Professional Documents
Culture Documents
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:
SUMMARY REPORT
________________________________________________________________________________________________________________
| Segment/Length | Section Identification | Offset |
|No| From | To | Length | Folder | Section | Section | Z | Y |
| | m | m | m | Name | Name | Type | mm | mm |
________________________________________________________________________________________________________________
| 1| 0.000| 7.180| 7.180| HollowCore | HC1200X500Th | Hollow-Core | 0.0| 0.0|
________________________________________________________________________________________________________________
Span Length at Transfer = 7.180 m, Centre of Supports, Left @ 0.000 m, Right @ 7.180 m
Span Length in Service = 7.180 m, Centre of Supports, Left @ 0.000 m, Right @ 7.180 m
Total Beam Length = 7.180 m, Bearing Length, Left = 0.0 mm, Right = 7.2 mm
Beam is part of a slab.
CAST-IN-PLACE POUR LAYOUT
______________________________________________________________________________________________
| Segment/Length | Slab/Topping Parameters | Haunch Paramaters |Vertical|
|No| From | To | Length | Thick. | Width | Offset | Thick. | Width | Offset | Offset |
| | m | m | m | mm | mm | mm | mm | mm | mm | mm |
______________________________________________________________________________________________
| 1| 0.000| 7.180| 7.180| 75.0| 1200.0| 0.0| 0.0| 0.0| 0.0| 0.0|
______________________________________________________________________________________________
Beam is UNSHORED during the cast-in-place pour and superimposed dead load.
__________________________________________________________________________________________________________________________________
GROSS PRECAST SECTION PROPERTIES (NON-COMPOSITE)
(based on Ec of the precast beam - transformed area of rebar and strand NOT included)
_______________________________________________________________________________________________________
|Seg.| Section Properties | Section| Section| Shear |Volume /| Section Moduli |
| No.| A | I | yb | Height | Width | Width | Surface| Sb | St |
| | mm^2 | mm^4 | mm | mm | mm | mm | mm | mm^3 | mm^3 |
_______________________________________________________________________________________________________
| 1| 313000 | 9.946E+9 | 247.0| 500.0| 1200.0| 310.0| 94.00| -40.268E+6 | 39.313E+6 |
_______________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________
Note: Sb & St = bottom and top of the precast beam, Sbc & Stc = bottom and top of the cast-in-place pour.
__________________________________________________________________________________________________________________________________
Engineer: Company:
File: Shear case.con 1 of 6 Thu Oct 19 13:07:28 2017
Summary Report
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:
| 4.344| 311520 | 9.890E+9 | 247.7| 321479 | 10.263E+9 | 243.3| 320836 | 10.239E+9 | 243.6| 401333 | 15.837E+9 | 302.5|
| 5.062| 311520 | 9.890E+9 | 247.7| 321479 | 10.263E+9 | 243.3| 320836 | 10.239E+9 | 243.6| 401333 | 15.837E+9 | 302.5|
| 5.780| 311520 | 9.890E+9 | 247.7| 321479 | 10.263E+9 | 243.3| 320836 | 10.239E+9 | 243.6| 401333 | 15.837E+9 | 302.5|
| 6.498| 311520 | 9.890E+9 | 247.7| 321479 | 10.263E+9 | 243.3| 320836 | 10.239E+9 | 243.6| 401333 | 15.837E+9 | 302.5|
| 7.180| 311520 | 9.917E+9 | 247.7| 313008 | 9.947E+9 | 247.0| 313008 | 9.947E+9 | 247.0| 393505 | 15.388E+9 | 306.4|
__________________________________________________________________________________________________________________________________
These section properties can used to calculate uncracked concrete stresses using the following guidelines.
Net Precast Section at Transfer properties are used with the initial prestress after transfer (after elastic shortening loss).
Transformed Precast Section at Transfer properties are used with the precast beam self-weight.
Transformed Precast Section in Service properties are used with external loads applied to the non-composite precast beam.
Transformed Composite Section in Service properties are used with external loads applied to the composite precast beam.
__________________________________________________________________________________________________________________________________
PRESTRESSING STEEL TENDONS
__________________________________________________________________________________________________________
| | | | | | Offsets |End Offset & Type| Tendon | Jacking Force |
|ID|Qty| Grade |Type| Strand Size | x | y |Left **|Right **| Area | Pj | %fpu|
| | | MPa | * | | m | mm | m | m | mm^2 | kN | |
__________________________________________________________________________________________________________
| 1| 11| 1860| LRS| 12.7 (1/2") | 0.000| 50.0| 0.000 B| 0.000 B| 1085.70 | 1252.0 | 0.62|
| | | | | | 7.180| 50.0| | | | | |
| 2| 2| 1860| LRS| 12.7 (1/2") | 0.000| 75.0| 0.000 B| 0.000 B| 197.40 | 227.6 | 0.62|
| | | | | | 7.180| 75.0| | | | | |
| 3| 2| 1860| LRS| 12.7 (1/2") | 0.000| 450.0| 0.000 B| 0.000 B| 197.40 | 227.6 | 0.62|
| | | | | | 7.180| 450.0| | | | | |
__________________________________________________________________________________________________________
note: * Type = LRS - Low-Relaxation Strand, SRS - Stress-Relieved Strand, PB - Plain Bar,
DB - Deformed Bar, SW - Single Wire
** End Types = B - Fully Bonded, D - Debonded, C - Cut, A - Anchored (fully developed)
Calculated Losses: Initial = 4.5%, Final = 16.4%
Maximum Total Prestress Forces: Pj(jacking) = 1707.3 kN,
Pi(transfer) = 1629.8 kN,
Pe(effective) = 1428.1 kN @ x = 3.590 m,
See the "Development Length" text report for details of the strand transfer and development lengths
__________________________________________________________________________________________________________________________________
SHEAR STIRRUPS
_______________________________________________________________________________________________________
| | | Stirrup| Stirrup| Number of Legs | Total Stirrup Area | Stirrup Spacing |
| From | To | Grade | Size | Stirrup |Interface| Stirrup | Interface | Stirrup |Interface|
| m | m | MPa | | in Beam | Ties | mm^2 | mm^2 | mm | mm |
_______________________________________________________________________________________________________
| 0.000| 7.180| 400| 15M | 0| 0| 0.0 | 0.0 | 0.0| 0.0|
_______________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________
TORSION PARAMETERS
Seg. Torsion Parameters
_____________________________________
|No.| Aoh | Ph |
| | mm^2 | mm |
_____________________________________
| 1| 0.0 | 0.0 |
_____________________________________
Aoh is the area enclosed by the centerline of the outermost closed transverse torsional reinforcement.
Ph is the perimeter of the area defined as Aoh.
__________________________________________________________________________________________________________________________________
____________________________________________________
| Segment/Length | Linear Weight |
| | From | To | Beam | Cast-in-Place |
|No.| m | m | kN/m | kN/m |
____________________________________________________
| 1| 0.000| 7.180| 7.3663 | 2.1181 |
____________________________________________________
__________________________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________
ANALYSIS RESULTS SUMMARY - IN SERVICE
__________________________________________________________________________________________
| | Total Unfactored Moments| Total Factored Effects |
| x | Total | Sustained | Shear | | Moment | | Torsion | |
| m | kNm | kNm | kN | [*]| kNm | [*]| kNm | [*]|
Engineer: Company:
File: Shear case.con 2 of 6 Thu Oct 19 13:07:28 2017
Summary Report
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:
__________________________________________________________________________________________
| 0.000| 0.0 | 0.0 | 198.2 |[ 1]| 0.0 |[ 1]| 0.0 |[ 1]|
| 0.682| 72.9 | 40.5 | 152.9 |[ 1]| 117.5 |[ 1]| 0.0 |[ 1]|
| 1.400| 132.7 | 74.0 | 115.1 |[ 1]| 213.8 |[ 1]| 0.0 |[ 1]|
| 2.118| 175.6 | 98.1 | 77.4 |[ 1]| 282.9 |[ 1]| 0.0 |[ 1]|
| 2.836| 201.7 | 112.7 | 39.6 |[ 1]| 324.8 |[ 1]| 0.0 |[ 1]|
| 2.908| 203.4 | 113.6 | 35.8 |[ 1]| 327.5 |[ 1]| 0.0 |[ 1]|
| 3.554| 210.9 | 117.9 | 1.8 |[ 1]| 339.7 |[ 1]| 0.0 |[ 1]|
| 3.590| 211.0 | 117.9 | -0.1 |[ 1]| 339.7 |[ 1]| 0.0 |[ 1]|
| 3.626| 210.9 | 117.9 | -2.0 |[ 1]| 339.7 |[ 1]| 0.0 |[ 1]|
| 4.272| 203.3 | 113.6 | -36.0 |[ 1]| 327.4 |[ 1]| 0.0 |[ 1]|
| 4.344| 201.6 | 112.7 | -39.8 |[ 1]| 324.6 |[ 1]| 0.0 |[ 1]|
| 5.062| 175.4 | 98.1 | -77.6 |[ 1]| 282.5 |[ 1]| 0.0 |[ 1]|
| 5.780| 132.4 | 74.0 | -115.4 |[ 1]| 213.2 |[ 1]| 0.0 |[ 1]|
| 6.498| 72.5 | 40.5 | -153.2 |[ 1]| 116.7 |[ 1]| 0.0 |[ 1]|
| 7.180| 0.0 | 0.0 | -189.1 |[ 1]| 0.0 |[ 1]| 0.0 |[ 1]|
__________________________________________________________________________________________
_________________________________________________________________
| | x | Stress | Limit | Overstress|
| Location | m | MPa | MPa | Notice |
_________________________________________________________________
|STRESSES AT TRANSFER |
|Critical Compression |
| Top of Beam | 3.590| 0.56 | 21.00 | 0%|
| Bottom of Beam | 6.606| 10.65 | 21.00 | 0%|
| | Longitudinal Tensile Rebar Needed (mm^2)
|Critical Tension | Required Provided Additional
| Top of Beam | 6.606| -0.52 | -2.95 | 0%|
| Bottom of Beam | 0.000| 0.01 | -2.95 | 0%|
_________________________________________________________________
|STRESSES DURING INITIAL LIFTING |
|Critical Compression |
| Top of Beam | 3.590| 0.56 | 21.00 | 0%|
| Bottom of Beam | 6.606| 10.65 | 21.00 | 0%|
| | Longitudinal Tensile Rebar Needed (mm^2)
|Critical Tension | Required Provided Additional
| Top of Beam | 6.606| -0.52 | -2.95 | 0%|
| Bottom of Beam | 0.000| 0.01 | -2.95 | 0%|
_________________________________________________________________
|STRESSES DURING ERECTION LIFTING |
|Critical Compression |
| Top of Beam | 3.590| 0.60 | 24.00 | 0%|
| Bottom of Beam | 6.606| 9.90 | 24.00 | 0%|
| | Longitudinal Tensile Rebar Needed (mm^2)
|Critical Tension | Required Provided Additional
| Top of Beam | 6.606| -0.46 | -3.15 | 0%|
| Bottom of Beam | 0.000| 0.01 | -3.15 | 0%|
_________________________________________________________________
|STRESSES DURING CAST-IN-PLACE POUR |
|Critical Compression |
| Top of Beam | 3.590| 0.94 | 24.00 | 0%|
| Bottom of Beam | 0.574| 9.81 | 24.00 | 0%|
| |
|Critical Tension |
| Top of Beam | 0.574| -0.36 | -3.15 | 0%|
| Bottom of Beam | 0.000| 0.01 | -3.15 | 0%|
_________________________________________________________________
|STRESSES IN SERVICE |
|Critical Compression |
| Top of Beam | 3.590| 2.84 | 24.00 | 0%|
Engineer: Company:
File: Shear case.con 3 of 6 Thu Oct 19 13:07:28 2017
Summary Report
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:
* Tensile stress limit given is for Class T (controlled cracking). Beyond this limit crack control is required.
Tensile stress limit given for the cast-in-place pour is the flexural cracking strength of the concrete.
At Transfer During Lifting In Service
Modulus of Rupture, fr = -3.68 MPa -3.68 MPa -3.94 MPa
Strength Required for Transfer, f'c = 17.8 MPa (f'c specified = 35 MPa)
Strength Required for Initial Lifting, f'c = 17.8 MPa (f'c assumed = 35 MPa)
__________________________________________________________________________________________________________________________________
Beam not cracked, cracking is controlled, or crack depth is less than concrete cover.
__________________________________________________________________________________________________________________________________
Live load includes roof load, and fluid weight. Wind and earthquake are not included.
Deflection growth is estimated by use of the PCI suggested multipliers - see the Deflection Multipliers report.
Span/Deflection Limits: DL growth + LL = L / 480 for non-structural attachments
L / 240 otherwise
LL alone = L / 360 for floors
L / 180 for roofs
__________________________________________________________________________________________________________________________________
SUPPORT ROTATIONS, AND CHANGE OF LENGTH AT ALL STAGES
Engineer: Company:
File: Shear case.con 4 of 6 Thu Oct 19 13:07:28 2017
Summary Report
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:
______________________________________________________________________________________________________________________
| | Factored | Design | Cracking | Minimum * | Depth in | Net Tensile| Flexural | | Notes & |
| | Moment | Strength | Moment | Required | Compression| Strain |Classication| | Warnings |
| x | Mu | Mn | Mcr | Strength | c | | | | |
| m | kNm | kNm | kNm | kNm | mm | | | | |
______________________________________________________________________________________________________________________
| 0.000| 0.0 | 0.5 | 198.3 | 0.0 | 0.8 | 2.0970|Tension | 0.75| |
| 0.682| 117.5 | 491.1 | 697.2 | 235.0 | 56.0 | 0.0252|Tension | 0.75| |
| 1.400| 213.8 | 669.9 | 696.4 | 427.5 | 76.8 | 0.0175|Tension | 0.75| |
| 2.118| 282.9 | 854.3 | 695.8 | 565.7 | 93.8 | 0.0138|Tension | 0.76| |
| 2.836| 324.8 | 1038.6 | 695.5 | 649.7 | 96.0 | 0.0134|Tension | 0.90| |
| 2.908| 327.5 | 1038.6 | 695.5 | 655.1 | 96.0 | 0.0134|Tension | 0.90| |
| 3.554| 339.7 | 1038.6 | 695.4 | 679.3 | 96.0 | 0.0134|Tension | 0.90| |
| 3.590| 339.7 | 1038.6 | 695.4 | 679.4 | 96.0 | 0.0134|Tension | 0.90| |
| 3.626| 339.7 | 1038.6 | 695.4 | 679.3 | 96.0 | 0.0134|Tension | 0.90| |
| 4.272| 327.4 | 1038.6 | 695.5 | 654.7 | 96.0 | 0.0134|Tension | 0.90| |
| 4.344| 324.6 | 1038.6 | 695.5 | 649.3 | 96.0 | 0.0134|Tension | 0.90| |
| 5.062| 282.5 | 854.3 | 695.8 | 565.0 | 93.8 | 0.0138|Tension | 0.76| |
| 5.780| 213.2 | 669.9 | 696.4 | 426.4 | 76.8 | 0.0175|Tension | 0.75| |
| 6.498| 116.7 | 491.1 | 697.2 | 233.5 | 56.0 | 0.0252|Tension | 0.75| |
| 7.180| 0.0 | 0.5 | 198.3 | 0.0 | 0.8 | 2.0970|Tension | 0.75| |
______________________________________________________________________________________________________________________
Points of Maximum and Minimum Factored Moment
| 3.590| 339.7 | 1038.6 | 695.4 | 679.4 | 96.0 | 0.0134|Tension | 0.90| |
| 0.000| 0.0 | -0.4 | 154.8 | 0.0 | 4.3 | 0.3146|Tension | 0.75| |
Points of Maximum Ratio of Factored Moment to Design Strength
| 2.046| 277.2 | 821.2 | 695.9 | 554.3 | 92.0 | 0.0141|Tension | 0.75| |
| 0.000| 0.0 | -0.4 | 154.8 | 0.0 | 4.3 | 0.3146|Tension | 0.75| |
______________________________________________________________________________________________________________________
* Minimum Strength Only Checked at Points of Maximum and Minimum Moment.
__________________________________________________________________________________________________________________________________
SHEAR DESIGN CHECK
Design Code Used: Custom Code based on ACI 318-02
_____________________________________________________________________________________________________________________
| | Design | Prestress| Concrete | Core Fill| Strength Provided | Min. Strength Req'd | Notes & |
| | Shear | Component| Strength | Strength | Stirrups | Total | Stirrups | Total | Warnings |
| x | Vu | Vp | Vc |Vc (core)| Vs | Vn | Vs | Vn | |
| m | kN | kN | kN | kN | kN | kN | kN | kN | |
_____________________________________________________________________________________________________________________
| 0.000| 198.2 | 0.0 | 267.4 | 330.7 | 0.0 | 598.1 | 0.0 | 267.4 | |
| 0.682| 152.9 | 0.0 | 420.0 | 0.0 | 0.0 | 420.0 | 0.0 | 420.0 | |
| 1.400| 115.1 | 0.0 | 357.5 | 0.0 | 0.0 | 357.5 | 0.0 | 357.5 | |
| 2.118| 77.4 | 0.0 | 204.2 | 0.0 | 0.0 | 204.2 | 0.0 | 204.2 | |
| 2.836| 39.6 | 0.0 | 152.7 | 0.0 | 0.0 | 152.7 | 0.0 | 152.7 | 7 |
| 2.908| 35.8 | 0.0 | 152.7 | 0.0 | 0.0 | 152.7 | 0.0 | 152.7 | 7 |
| 3.554| 1.8 | 0.0 | 152.7 | 0.0 | 0.0 | 152.7 | 0.0 | 152.7 | 7 |
| 3.590| -0.1 | 0.0 | -152.7 | 0.0 | 0.0 | -152.7 | 0.0 | -152.7 | 7 |
| 3.626| -2.0 | 0.0 | -152.7 | 0.0 | 0.0 | -152.7 | 0.0 | -152.7 | 7 |
| 4.272| -36.0 | 0.0 | -152.7 | 0.0 | 0.0 | -152.7 | 0.0 | -152.7 | 7 |
| 4.344| -39.8 | 0.0 | -152.7 | 0.0 | 0.0 | -152.7 | 0.0 | -152.7 | 7 |
| 5.062| -77.6 | 0.0 | -205.0 | 0.0 | 0.0 | -205.0 | 0.0 | -205.0 | |
| 5.780| -115.4 | 0.0 | -359.2 | 0.0 | 0.0 | -359.2 | 0.0 | -359.2 | |
| 6.498| -153.2 | 0.0 | -420.0 | 0.0 | 0.0 | -420.0 | 0.0 | -420.0 | |
| 7.180| -173.8 | 0.0 | -267.4 | -330.7 | 0.0 | -598.1 | 0.0 | -267.4 | 5 |
_____________________________________________________________________________________________________________________
Notes & Warnings
5 - Note: Design shear force limited to critical section near support.
7 - Note: The calculation of the shear strength of the concrete used the simplified method.
Note: Beam is part of a slab.
__________________________________________________________________________________________________________________________________
_________________________________________________________________________________________
| | Design | Threshold| Combined Shear | Torsion Strength | Notes & |
| | Torsion | Torsion | and Torsion | Provided | Required | Warnings |
| x | Tu | Tcr/4 | Stress | Limit | Tn | Tn | |
| m | kNm | kNm | MPa | MPa | kNm | kNm | |
_________________________________________________________________________________________
| 0.000| 0.0 | 20.4 | 0.00 | 0.00 | 0.0 | 0.0 | 2 |
| 0.682| 0.0 | 33.4 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 1.400| 0.0 | 33.7 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 2.118| 0.0 | 34.0 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 2.836| 0.0 | 34.2 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 2.908| 0.0 | 34.2 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 3.554| 0.0 | 34.2 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 3.590| 0.0 | 34.2 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 3.626| 0.0 | 34.2 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 4.272| 0.0 | 34.2 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 4.344| 0.0 | 34.2 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 5.062| 0.0 | 34.0 | 0.00 | 0.00 | 0.0 | 0.0 | |
Engineer: Company:
File: Shear case.con 5 of 6 Thu Oct 19 13:07:28 2017
Summary Report
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:
_______________________________________________________________________________________________________________________
| | Shear Steel Required |Shear Steel| Stirrup | Stirrup Spacing | Additional Long. Steel| Notes & |
| | Total | Torsion* | Provided | Provided | Provided | Required | for Torsion, Al | Warnings |
| x | (Av+2At)/s| At/s | Av/s | Av+2At | s | s | Total |Reduction**| |
| m | mm^2/m | mm^2/m | mm^2/m | mm^2 | mm | mm | mm^2 | mm^2 | |
_______________________________________________________________________________________________________________________
| 0.000| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 0.682| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 1.400| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 2.118| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 2.836| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 2.908| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 3.554| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 3.590| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 3.626| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 4.272| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 4.344| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 5.062| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 5.780| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 6.498| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | |
| 7.180| 0 | 0 | 0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 5 |
_______________________________________________________________________________________________________________________
Notes & Warnings
5 - Note: Design torsion force limited to critical section near support.
Note: Beam is part of a slab.
Note: Additional long. steel in compression side of section has been reduced.
* Portion of the total stirrup area required to resist torsional shear flow (one leg around periphery).
** The allowable reduction in Al within the flexural compression zone.
__________________________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________
HORIZONTAL SHEAR DESIGN CHECK BY SECTION
Design Code Used: Custom Code based on ACI 318-02
Top of precast beam is considered intentionally roughened.
_____________________________________________________________________________________________________________
| |Horizontal| Strength | Required | Tie Size | Spacing | Spacing | Strength | Strength | Notes & |
| | Shear | with no | Ties | Provided | Required | Provided | Required | Provided | Warnings |
| x | Vu | ties | Av/s | Av | s | s | Vnh | Vnh | |
| m | kN | kN | mm^2/m | mm^2 | mm | mm | kN | kN | |
_____________________________________________________________________________________________________________
| 0.000| 198.2 | 300.1 | 0 | 0.0 | 0.0 | 0.0 | 198.2 | 300.1 | 3 |
| 0.682| 152.9 | 300.1 | 0 | 0.0 | 0.0 | 0.0 | 152.9 | 300.1 | 3 |
| 1.400| 115.1 | 300.1 | 0 | 0.0 | 0.0 | 0.0 | 115.1 | 300.1 | 3 |
| 2.118| 77.4 | 300.1 | 0 | 0.0 | 0.0 | 0.0 | 77.4 | 300.1 | 3 |
| 2.836| 39.6 | 300.1 | 0 | 0.0 | 0.0 | 0.0 | 39.6 | 300.1 | 3 |
| 2.908| 35.8 | 300.1 | 0 | 0.0 | 0.0 | 0.0 | 35.8 | 300.1 | 3 |
| 3.554| 1.8 | 300.1 | 0 | 0.0 | 0.0 | 0.0 | 1.8 | 300.1 | 3 |
| 3.590| -0.1 | -300.1 | 0 | 0.0 | 0.0 | 0.0 | -0.1 | -300.1 | 3 |
| 3.626| -2.0 | -300.1 | 0 | 0.0 | 0.0 | 0.0 | -2.0 | -300.1 | 3 |
| 4.272| -36.0 | -300.1 | 0 | 0.0 | 0.0 | 0.0 | -36.0 | -300.1 | 3 |
| 4.344| -39.8 | -300.1 | 0 | 0.0 | 0.0 | 0.0 | -39.8 | -300.1 | 3 |
| 5.062| -77.6 | -300.1 | 0 | 0.0 | 0.0 | 0.0 | -77.6 | -300.1 | 3 |
| 5.780| -115.4 | -300.1 | 0 | 0.0 | 0.0 | 0.0 | -115.4 | -300.1 | 3 |
| 6.498| -153.2 | -300.1 | 0 | 0.0 | 0.0 | 0.0 | -153.2 | -300.1 | 3 |
| 7.180| -173.8 | -300.1 | 0 | 0.0 | 0.0 | 0.0 | -173.8 | -300.1 | 3 |
_____________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
| Region of Beam | Shear | Peak | Horizontal | Strength | Tie Area * | Tie Area | Maximum | Notes & |
| | Length | Moment | Shear | with no | Required | Provided | Spacing | Warnings |
| x | lv | M | Fh | ties | Acs | Acs | s | |
| m | m | kNm | kN | kN | mm^2 | mm^2 | mm | |
_____________________________________________________________________________________________________________________
| 0.000 to 3.590| 3.590| 339.7 | 800.7 | 2067.4 | 0.0 | 0.0 | 300 | |
| 3.590 to 7.180| 3.590| 339.7 | 800.7 | 2067.4 | 0.0 | 0.0 | 300 | |
_____________________________________________________________________________________________________________________
* Required ties should be distributed in proportion to distribution of shear force (or stirrups).
Engineer: Company:
File: Shear case.con 6 of 6 Thu Oct 19 13:07:28 2017