You are on page 1of 8

4 Troubleshooting

4 Troubleshooting
4-1 Common Acknowledge

- If you change the interface board, be sure that the U105, U106 and U103 these three components also
changed to the new I/F board because there was program inside. If not, please re-write EDID or upload
firmware into Flash memory via VGA Cable.
- If you adjust clock and phase, please do it at the condition of Windows shut down pattern.
- If you confirm the R.G.B. color is normal or not, please do it under 16-grey scalar pattern.
- This LCM is analog interface. So if the entire screen is an abnormal color that means the problem
happen in the analog circuit part, if only some scale appears abnormal color that stand the problem
happen in the digital circuit part.
- If you check the H/V position, please use the crosshatch pattern.
- This LCM support more than 30 timing modes, if the input timing mode is out of specification, the picture
may appears abnormally.
- If brightness uneven, repairs Inverter circuit or change a new panel.
- If you find the vertical line or horizontal line lost on the screen, please change panel.

4-1
4 Troubleshooting

4-2 No Power & Power LED Off

No power

Check primary Check circuit if Check IC802,


rectifier voltage short C805, T801

Check F801, P801,


RT,801,D801

Check pin6 of
IC802 voltage Check C810,D803,C807
about 12V

Check pin2 of
Check primary OVP, OLP
IC802 voltage
and secondary feedback,
about 3V

Check pin1 of
Check R811, R810,
IC802 voltage is
R809, R808,R814
voltage is below 1V

END

4-2
4 Troubleshooting

4-3 Output power is unstable

Unstable power

Check sampling Check R822, R823,


Circuit R824

Change R822, R823,


R824

Check the R pin Check the C pin


voltage of IC803 voltage of IC803 if Change IC803
about 2.5V 3V

Check R819, R820

Check pin1 of
Check R818, D804,
IC802 voltage is
C807 if short
5.8V

Change R818

Check pin1 of Change R808, R809,


IC802 voltage R810, R811
about 3V

END

4-3
4 Troubleshooting

4-4 Backlight can't be turned on

No backlight

Yes

No Yes
No power supply to Check the cable that from
LED lamp is OK
inverter I/F BD to P/I BD is ok

Yes

Is there 14V No No
voltage on pin 3,4 U501, U502 fail Check power supply
of T501, T502

Yes Replace U501, U502

Is there PWM No
signal on pin 4 of Check I/F BD
IC501

Yes

Is there High level No


voltage on pin10 of Check I/F BD
IC501

Yes

No
Vsense voltage
Lamp connector opened
2.9V

No

Are there PWM No


signal on pin1, IC501 failure
pin15 of IC501

Yes

Yes Yes
Pin 5 of IC501 Check C524,R528, R533,
Feedback circuit failure
voltage is Low level D507

Yes

Pin 3 of IC501 Yes Yes


voltage is high level IC501 protected Check D505, D511,
voltage D512, R513, R520, C520

END

4-4
4 Troubleshooting

4-5 Black Screen and backlight turn on

Black Screen

Check power No
supply: Pin1, 2 of Power Fail
CN102

Yes

Check pin34, 51, No


66, and 82 Of Check FB103 And U102
U105

Yes

Check pin12, 68, No


97 and 117 Of Check FB105 And U106
U103

Yes

Check Reset No
Check C149, R157
(pin19) Of U103

Yes

Check Crystal: No
Pin32, Pin33 Of Check: X1, C147, C148
U103

Yes

Check CCFL- Yes Yes


Check pin5 of
Enable (pin20) of Inverter Fail
CN102
U103

No No
Check R127, Q101,
R125, R126
MCU Fail

4-5
4 Troubleshooting

4-6 White Screen

White Screen

LVDS Cable Yes


Workmanship
Reinsert

No

Change LVDS Yes


LVDS Cable NG
Cable

No

Yes Yes
Check VLCD Is Check LVDS Panel Fail
5V? Signals

No No

Check Panel Check the HW No


Enable Of U103 Reset Of U103 Check C149 R157
(pin75) is High? pin19

No
Yes

Check R134, R176,


Q102, Q105
Check the pins Of
U103

END

4-6
4 Troubleshooting

4-8 Bad Screen

Bad Screen

LVDS Cable Yes


Workmanship
Reinsert

No

Change LVDS Yes


LVDS Cable NG
Cable

No

Check Yes
Crystal:Pin32, Check :X1, C147, C148
Pin33 of U103

Yes

Check the No Check: SDO, SCZ, SCK,


communication Of
SDI, Reset
U103 and U104

Yes

Check the pins of U103


and U104

4-7
4 Troubleshooting

Memo

4-8

You might also like