You are on page 1of 11

Hollowcore Slab Design

Design of Hollowcore Slabs 200mm Covering Case Freezone Substation Wh,


Substation-Building 1,Building 2 & LIU Substation Building 1,Building 2:
Design of the Typical Hc-Slabs For Gravity Loads:

Hollowcore Slabs Thick: = 200 mm


C.I.S Top Slabs Thick: = 75 mm

Strands Number & Size Offset from soffit Jacking Force


Layer-1 7 - # 12.7mm 30 110 kN

Max Span Length = 6.03 m


Max imposed Live Load = 2.5*1.2 = 3 kN/m
Max imposed Dead Load = 3*1.2 = 3.6 kN/m
Additional load cover slab = 5 kN/m(conservatively apply over full span)
(conservatively consider distributed along the slab)
Dead Load of topping = 0.075*25*1.2 = 2.25 kN/m

Please find attached below the output of Concise Beam 5.59x


HC1200X200Xtec

Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:

Section Name: HC1200X200Xtec


Section Type: Unspecified
Folder Name: HollowCore
Library File:

Section Properties
Area: 128600 mm^2
Moment of Inertia: 644.035E+6 mm^4
Height of Section: 200 mm
Height of NA: 102 mm
Shear Width: 263 mm
Volume/Area: 47 mm

Polygon Node Coordinates (mm)

Polygon 1 2 3 4 5 6 7
Type Solid Void Void Void Void Void Void
Node x y x y x y x y x y x y x y
1 -600 0 -547 95 -359 95 -171 95 18 95 206 95 394 95
2 600 0 -542 128 -354 128 -166 128 23 128 211 128 399 128
3 580 200 -523 153 -335 153 -147 153 41 153 229 153 417 153
4 -580 200 -499 164 -311 164 -123 164 65 164 253 164 441 164
5 -470 170 -282 170 -94 170 94 170 282 170 470 170
6 -441 164 -253 164 -65 164 123 164 311 164 499 164
7 -417 153 -229 153 -41 153 147 153 335 153 523 153
8 -398 130 -210 130 -22 130 167 130 355 130 543 130
9 -394 95 -206 95 -18 95 171 95 359 95 547 95
10 -396 67 -208 67 -20 67 169 67 357 67 545 67
11 -408 43 -220 43 -32 43 157 43 345 43 533 43
12 -433 30 -245 30 -57 30 131 30 319 30 507 30
13 -507 30 -319 30 -131 30 57 30 245 30 433 30
14 -533 44 -345 44 -157 44 31 44 219 44 407 44
15 -544 66 -356 66 -168 66 21 66 209 66 397 66

Engineer: Company:
File: hc200 design.con 1 of 1 Tue Oct 17 15:13:44 2017
Flexural Design Graph
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:

Flexural Design
300

270

240

210
Moment - kNm

180

150

120

90

60

30

0.000 0.603 1.205 1.808 2.410 3.013 3.615 4.218 4.820 5.423 6.025

Distance From Left End of Beam - m

Factored Moment, Mu: +ve Bending


Design Strength, Mn: +ve Bending

Engineer: Company:
File: hc200 design.con Tue Oct 17 14:56:57 2017
Shear Design Graph

Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:

Shear Design
200

160

120

80

40
Shear - kN

-40

-80

-120

-160

-200

0.000 0.603 1.205 1.808 2.410 3.013 3.615 4.218 4.820 5.423 6.025

Distance From Left End of Beam - m

Factored Design Shear, Vu


Total Strength Provided, Vn
Minimum Strength Required
Concrete Strength Provided, Vc
Critical Section for Shear Loading

Engineer: Company:
File: hc200 design.con Tue Oct 17 16:15:46 2017
Concrete Stress in Service, Beam Graph
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:

Concrete Stress in Service, Beam


35.00

30.00

25.00
Stress (compression +ve) - MPa

20.00

15.00

10.00

5.00

0.00

-5.00

-10.00

-15.00

0.000 0.603 1.205 1.808 2.410 3.013 3.615 4.218 4.820 5.423 6.025

Distance From Left End of Beam - m

Stress at Top of Beam


Stress at Bottom of Beam
Compression Limit
Tension Limit, Controlled Cracking (Class T)
Tension Limit, Full Prestressing (Class U)

Engineer: Company:
File: hc200 design.con Tue Oct 17 14:57:36 2017
Deflection Estimate on Final Supports Graph
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:

Deflection Estimate on Final Supports


30.00

27.00

24.00

21.00
Deflection - mm

18.00

15.00

12.00

9.00

6.00

3.00

0.00

0.000 0.603 1.205 1.808 2.410 3.013 3.615 4.218 4.820 5.423 6.025

Distance From Left End of Beam - m

Deflection @ Erection
Deflection On Completion
Final DL Deflection
Final DL + LL Deflection

Engineer: Company:
File: hc200 design.con Tue Oct 17 14:57:20 2017
Summary Report

Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:

SUMMARY REPORT

Design Code Used: ACI 318-08


__________________________________________________________________________________________________________________________________

CONCRETE MATERIAL PROPERTIES


Precast Beam Cast-in-Place Pour
___________________________ ___________________________
Concrete Density Wt = 2400 kg/m^3 Wt = 2400 kg/m^3
Compressive Strength f'c = 40.0 MPa f'c = 32.0 MPa
Modulus of Elasticity Ec = 31783 MPa Ec = 28427 MPa
Strength at Transfer f'c = 28.0 MPa
Modulus of Elast. at Transfer Ec = 26591 MPa
Strength at Lifting f'c = 28.0 MPa
Modulus of Elast. at Lifting Ec = 26591 MPa

Curing Method = Moist


Relative Humidity in Service = 70 %
Ambient Temperature in Service = 20 deg C

__________________________________________________________________________________________________________________________________

PRECAST BEAM LAYOUT


________________________________________________________________________________________________________________
| Segment/Length | Section Identification | Offset |
|No| From | To | Length | Folder | Section | Section | Z | Y |
| | m | m | m | Name | Name | Type | mm | mm |
________________________________________________________________________________________________________________
| 1| 0.000| 6.025| 6.025| HollowCore | HC1200X200Xtec | Unspecified | 0.0| 0.0|
________________________________________________________________________________________________________________
Span Length at Transfer = 6.025 m, Centre of Supports, Left @ 0.000 m, Right @ 6.025 m
Span Length in Service = 5.925 m, Centre of Supports, Left @ 0.050 m, Right @ 5.975 m
Total Beam Length = 6.025 m, Bearing Length, Left = 100.0 mm, Right = 100.0 mm
Beam is part of a slab.
CAST-IN-PLACE POUR LAYOUT
______________________________________________________________________________________________
| Segment/Length | Slab/Topping Parameters | Haunch Paramaters |Vertical|
|No| From | To | Length | Thick. | Width | Offset | Thick. | Width | Offset | Offset |
| | m | m | m | mm | mm | mm | mm | mm | mm | mm |
______________________________________________________________________________________________
| 1| 0.000| 6.025| 6.025| 75.0| 1200.0| 0.0| 0.0| 0.0| 0.0| 0.0|
______________________________________________________________________________________________
Beam is UNSHORED during the cast-in-place pour and superimposed dead load.
__________________________________________________________________________________________________________________________________
GROSS PRECAST SECTION PROPERTIES (NON-COMPOSITE)
(based on Ec of the precast beam - transformed area of rebar and strand NOT included)
_______________________________________________________________________________________________________
|Seg.| Section Properties | Section| Section| Shear |Volume /| Section Moduli |
| No.| A | I | yb | Height | Width | Width | Surface| Sb | St |
| | mm^2 | mm^4 | mm | mm | mm | mm | mm | mm^3 | mm^3 |
_______________________________________________________________________________________________________
| 1| 128600 | 644.035E+6 | 102.0| 200.0| 1200.0| 263.0| 47.00| -6.314E+6 | 6.572E+6 |
_______________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________
UNCRACKED SECTION PROPERTIES SUMMARY
__________________________________________________________________________________________________________________________________
| | Net Precast Section | Transformed Precast Section | Transformed Precast Section |Transformed Composite Section|
| | at Transfer (based on Eci) | at Transfer (based on Eci) | in Service (based on Ec) | in Service (based on Ec) |
| |(include rebar,deduct strand)| (include rebar and strand) | (include rebar and strand) | (include rebar and strand) |
| x | A | I | yb | A | I | yb | A | I | yb | Ac | Ic | ybc |
| m | mm^2 | mm^4 | mm | mm^2 | mm^4 | mm | mm^2 | mm^4 | mm | mm^2 | mm^4 | mm |
__________________________________________________________________________________________________________________________________
| 0.000| 127909 |640.434E+6 | 102.4| 128605 |644.059E+6 | 102.0| 128604 |644.054E+6 | 102.0| 209100 | 1.591E+9 | 154.2|
| 0.050| 127909 |640.434E+6 | 102.4| 129018 |646.197E+6 | 101.8| 128940 |645.791E+6 | 101.8| 209436 | 1.596E+9 | 154.0|
| 0.524| 127909 |640.434E+6 | 102.4| 132985 |666.020E+6 | 99.6| 132159 |661.989E+6 | 100.1| 212656 | 1.645E+9 | 152.1|
| 1.117| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 1.709| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 2.301| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 2.539| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 2.894| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 3.013| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 3.131| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 3.486| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 3.724| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 4.316| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 4.909| 127909 |640.434E+6 | 102.4| 133106 |666.602E+6 | 99.6| 132257 |662.467E+6 | 100.0| 212754 | 1.646E+9 | 152.0|
| 5.501| 127909 |640.434E+6 | 102.4| 132985 |666.020E+6 | 99.6| 132159 |661.989E+6 | 100.1| 212656 | 1.645E+9 | 152.1|
| 5.975| 127909 |640.434E+6 | 102.4| 129018 |646.197E+6 | 101.8| 128940 |645.791E+6 | 101.8| 209436 | 1.596E+9 | 154.0|
| 6.025| 127909 |640.434E+6 | 102.4| 128605 |644.059E+6 | 102.0| 128604 |644.054E+6 | 102.0| 209100 | 1.591E+9 | 154.2|
__________________________________________________________________________________________________________________________________

These section properties can used to calculate uncracked concrete stresses using the following guidelines.

Net Precast Section at Transfer properties are used with the initial prestress after transfer (after elastic shortening loss).
Transformed Precast Section at Transfer properties are used with the precast beam self-weight.
Transformed Precast Section in Service properties are used with external loads applied to the non-composite precast beam.
Transformed Composite Section in Service properties are used with external loads applied to the composite precast beam.

__________________________________________________________________________________________________________________________________

PRESTRESSING STEEL TENDONS

__________________________________________________________________________________________________________

Engineer: Company:
File: hc200 design.con 1 of 5 Tue Oct 17 15:15:50 2017
Summary Report

Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:

| | | | | | Offsets |End Offset & Type| Tendon | Jacking Force |


|ID|Qty| Grade |Type| Strand Size | x | y |Left **|Right **| Area | Pj | %fpu|
| | | MPa | * | | m | mm | m | m | mm^2 | kN | |
__________________________________________________________________________________________________________
| 1| 7| 1860| LRS| 12.7 (1/2") | 0.000| 30.0| 0.000 B| 0.000 B| 690.90 | 758.2 | 0.59|
| | | | | | 6.025| 30.0| | | | | |
__________________________________________________________________________________________________________
note: * Type = LRS - Low-Relaxation Strand, SRS - Stress-Relieved Strand, PB - Plain Bar,
DB - Deformed Bar, SW - Single Wire
** End Types = B - Fully Bonded, D - Debonded, C - Cut, A - Anchored (fully developed)
User predefined losses: Initial = 0.0%, Final = 0.0% (Varies with concrete stress)
Maximum Total Prestress Forces: Pj(jacking) = 758.2 kN,
Pi(transfer) = 758.2 kN,
Pe(effective) = 758.2 kN @ x = 3.013 m,

See the "Development Length" text report for details of the strand transfer and development lengths
__________________________________________________________________________________________________________________________________

PRECAST BEAM AND CAST-IN-PLACE POUR SELF-WEIGHT

____________________________________________________
| Segment/Length | Linear Weight |
| | From | To | Beam | Cast-in-Place |
|No.| m | m | kN/m | kN/m |
____________________________________________________
| 1| 0.000| 6.025| 3.0265 | 2.1181 |
____________________________________________________

__________________________________________________________________________________________________________________________________
EXTERNALLY APPLIED LOADS
________________________________________________________________________________________________________________
| Load Case |Type| Label | Description | Distribution |
________________________________________________________________________________________________________________
|SDL AT | D |SDL |Vertical: 3.6 kN/m full length |No Load Distribution|
|SDL AT | D |Cover Slab |Vertical: 5 kN/m full length |No Load Distribution|
|Live Load | L |Load #1 |Vertical: 3 kN/m full length |No Load Distribution|
________________________________________________________________________________________________________________
Load Combinations
Factored Combination 1 = 1.40D + 1.40F
Factored Combination 2 = 1.20D + 1.60L + 0.50SRLr + 1.20F
Factored Combination 3 = 1.20D + 1.00L + 1.60SRLr
Factored Combination 4 = 1.20D + 1.60SRLr + 0.80W
Factored Combination 5 = 1.20D + 1.00L + 0.50SRLr + 1.60W
Factored Combination 6 = 1.20D + 1.00L + 0.50SRLr + 1.60W
Factored Combination 7 = 0.90D + 1.60W
Factored Combination 8 = 0.90D + 1.00E
__________________________________________________________________________________________________________________________________
ANALYSIS RESULTS SUMMARY - IN SERVICE
__________________________________________________________________________________________
| | Total Unfactored Moments| Total Factored Effects |
| x | Total | Sustained | Shear | | Moment | | Torsion | |
| m | kNm | kNm | kN | [*]| kNm | [*]| kNm | [*]|
__________________________________________________________________________________________
| 0.000| 0.0 | 0.0 | 0.0 |[ 1]| 0.0 |[ 1]| 0.0 |[ 1]|
| 0.050| 0.0 | 0.0 | -1.1 |[ 2]| 0.0 |[ 2]| 0.0 |[ 1]|
| 0.050| 0.0 | 0.0 | 63.1 |[ 2]| 0.0 |[ 2]| 0.0 |[ 1]|
| 0.524| 21.6 | 17.7 | 53.0 |[ 2]| 27.5 |[ 2]| 0.0 |[ 1]|
| 1.117| 43.4 | 35.6 | 40.4 |[ 2]| 55.1 |[ 2]| 0.0 |[ 1]|
| 1.709| 59.2 | 48.6 | 27.8 |[ 2]| 75.3 |[ 2]| 0.0 |[ 1]|
| 2.301| 69.2 | 56.8 | 15.1 |[ 2]| 88.0 |[ 2]| 0.0 |[ 1]|
| 2.539| 71.6 | 58.8 | 10.1 |[ 2]| 91.0 |[ 2]| 0.0 |[ 1]|
| 2.894| 73.3 | 60.2 | 2.5 |[ 2]| 93.3 |[ 2]| 0.0 |[ 1]|
| 3.013| 73.5 | 60.3 | 0.0 |[ 1]| 93.4 |[ 2]| 0.0 |[ 1]|
| 3.131| 73.3 | 60.2 | -2.5 |[ 2]| 93.3 |[ 2]| 0.0 |[ 1]|
| 3.486| 71.6 | 58.8 | -10.1 |[ 2]| 91.0 |[ 2]| 0.0 |[ 1]|
| 3.724| 69.2 | 56.8 | -15.1 |[ 2]| 88.0 |[ 2]| 0.0 |[ 1]|
| 4.316| 59.2 | 48.6 | -27.8 |[ 2]| 75.3 |[ 2]| 0.0 |[ 1]|
| 4.909| 43.4 | 35.6 | -40.4 |[ 2]| 55.1 |[ 2]| 0.0 |[ 1]|
| 5.501| 21.6 | 17.7 | -53.0 |[ 2]| 27.5 |[ 2]| 0.0 |[ 1]|
| 5.975| 0.0 | 0.0 | -63.1 |[ 2]| 0.0 |[ 2]| 0.0 |[ 1]|
| 5.975| 0.0 | 0.0 | 1.1 |[ 2]| 0.0 |[ 2]| 0.0 |[ 1]|
| 6.025| 0.0 | 0.0 | 0.0 |[ 1]| 0.0 |[ 1]| 0.0 |[ 1]|
__________________________________________________________________________________________

* Critical ULS Load Combination


__________________________________________________________________________________________________________________________________

SUPPORT REACTIONS (kN)


(+ve = upwards)

Unfactored Support Reactions


___________________________________________________________________________________________
| | In Service | During Lifting | During Transport |
| Load Case | Left | Right | Left | Right | Left | Right |
___________________________________________________________________________________________
|Beam Weight| 9.1 | 9.1 | 9.1 | 9.1 | 9.1 | 9.1 |
|SDL BT | 0.0 | 0.0 | | | | |
|CIP Weight | 6.4 | 6.4 | | | | |
|SDL AT | 25.9 | 25.9 | | | | |
|LL Sustain | 0.0 | 0.0 | | | | |
|Live Load | 9.0 | 9.0 | | | | |
|Roof Load | 0.0 | 0.0 | | | | |
|Fluid Wgt | 0.0 | 0.0 | | | | |
|Wind | 0.0 | 0.0 | | | | |
|Seismic | 0.0 | 0.0 | | | | |
|Constrct LL| 0.0 | 0.0 | | | | |
___________________________________________________________________________________________

Engineer: Company:
File: hc200 design.con 2 of 5 Tue Oct 17 15:15:50 2017
Summary Report

Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:

|SLS Maximum| 50.4 | 50.4 | 9.1 | 9.1 | 9.1 | 9.1 |


|SLS Max DL | 41.4 | 41.4 | | | | |
|SLS Min DL | 41.4 | 41.4 | | | | |
|SLS Max Sus| 41.4 | 41.4 | | | | |
___________________________________________________________________________________________

ULS Support Reactions


_________________________________________________
|Load Combo.| Left [*]| Right [*]|
_________________________________________________
|ULS Maximum| 64.1 [ 2]| 64.1 [ 2]|
|ULS Minimum| 37.3 [ 7]| 37.3 [ 7]|
_________________________________________________

* Critical Factored Load Combination


__________________________________________________________________________________________________________________________________

CONCRETE STRESS RESULTS (UNCRACKED ANALYSIS)


(+ve = compression, -ve = tension)

_________________________________________________________________
| | x | Stress | Limit | Overstress|
| Location | m | MPa | MPa | Notice |
_________________________________________________________________
|STRESSES AT TRANSFER |
|Critical Compression |
| Top of Beam | 0.000| 0.00 | 19.60 | 0%|
| Bottom of Beam | 4.672| 13.23 | 16.80 | 0%|
| | Longitudinal Tensile Rebar Needed (mm^2)
|Critical Tension | Required Provided Additional
| Top of Beam | 4.672| -0.99 | -1.32 | 0%|
| Bottom of Beam | 0.000| 0.01 | -2.64 | 0%|
_________________________________________________________________
|STRESSES DURING INITIAL LIFTING |
|Critical Compression |
| Top of Beam | 0.000| 0.00 | 19.60 | 0%|
| Bottom of Beam | 4.672| 13.23 | 16.80 | 0%|
| | Longitudinal Tensile Rebar Needed (mm^2)
|Critical Tension | Required Provided Additional
| Top of Beam | 4.672| -0.99 | -1.32 | 0%|
| Bottom of Beam | 0.000| 0.01 | -2.64 | 0%|
_________________________________________________________________
|STRESSES DURING ERECTION LIFTING |
|Critical Compression |
| Top of Beam | 0.000| 0.00 | 28.00 | 0%|
| Bottom of Beam | 4.672| 13.04 | 24.00 | 0%|
| | Longitudinal Tensile Rebar Needed (mm^2)
|Critical Tension | Required Provided Additional
| Top of Beam | 4.672| -0.96 | -1.58 | 0%|
| Bottom of Beam | 0.000| 0.01 | -3.15 | 0%|
_________________________________________________________________
|STRESSES DURING CAST-IN-PLACE POUR |
|Critical Compression |
| Top of Beam | 3.013| 0.97 | 24.00 | 0%|
| Bottom of Beam | 4.672| 12.15 | 24.00 | 0%|
| |
|Critical Tension |
| Top of Beam | 5.383| -1.14 | -3.15 | 0%|
| Bottom of Beam | 0.000| 0.01 | -3.15 | 0%|
_________________________________________________________________
|STRESSES IN SERVICE |
|Critical Compression |
| Top of Beam | 3.013| 2.45 | 24.00 | 0%|
| Bottom of Beam | 5.383| 11.01 | 24.00 | 0%|
| Top of CIP Pour| 3.013| 3.40 | 19.20 | 0%|
|Critical Tension |
| Top of Beam | 5.383| -0.55 | -6.30 |* 0%| Class U member - not cracked
| Bottom of Beam | 0.000| 0.01 | -6.30 |* 0%| Class U member - not cracked
| Top of CIP Pour| 0.050| 0.00 | -3.52 |* 0%|
_________________________________________________________________
|STRESSES IN SERVICE (SUSTAINED LOADS ONLY) |
|Critical Compression |
| Top of Beam | 3.013| 2.06 | 18.00 | 0%|
| Bottom of Beam | 5.383| 11.45 | 18.00 | 0%|
_________________________________________________________________
* Tensile stress limit given is for Class T (controlled cracking). Beyond this limit crack control is required.
Tensile stress limit given for the cast-in-place pour is the flexural cracking strength of the concrete.

At Transfer During Lifting In Service


Modulus of Rupture, fr = -3.30 MPa -3.30 MPa -3.94 MPa
Strength Required for Transfer, f'c = 22.0 MPa (f'c specified = 28 MPa)
Strength Required for Initial Lifting, f'c = 22.0 MPa (f'c assumed = 28 MPa)

__________________________________________________________________________________________________________________________________

DISTRIBUTION OF FLEXURAL STEEL & CRACKING


(+ve = tension, -ve = compression)

Beam not cracked, cracking is controlled, or crack depth is less than concrete cover.

__________________________________________________________________________________________________________________________________

DEFLECTION ESTIMATE AT ALL STAGES

Design Code Used: ACI 318-08

THESE DEFLECTIONS ARE BASED ON MIDSPAN PROPERTIES THROUGHOUT THE LENGTH OF THE BEAM.

A. Deflections at All Stages


(-ve = deflection down, +ve = camber up)
_____________________________________________________________________________________________________________
| | Net Deflection | Change in Deflection |

Engineer: Company:
File: hc200 design.con 3 of 5 Tue Oct 17 15:15:50 2017
Summary Report

Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:

|Location| Net @ | Net @ | Net @ | Net DL | Net Total| DL growth| LL | Span/Deflection |


| x | Transfer | Erection |Completion| @ Final | @ Final | + LL | alone | DL growth| LL |
| m | mm | mm | mm | mm | mm | mm | mm | + LL | alone |
| Column | A | B | C | D | E | E - C | E - D | | |
_____________________________________________________________________________________________________________
| 0.000| 0.0 | -0.6 | -0.6 | -0.5 | -0.4 | 0.2 | 0.0 | 544 | 4026 |
| 0.050| 0.4 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0 | 0 |
| 0.524| 3.6 | 5.9 | 5.7 | 4.2 | 3.9 | -1.7 | -0.2 | 3429 | 25481 |
| 1.117| 7.0 | 11.9 | 11.3 | 8.1 | 7.6 | -3.7 | -0.5 | 1583 | 11886 |
| 1.709| 9.4 | 16.3 | 15.3 | 10.6 | 9.9 | -5.4 | -0.7 | 1097 | 8311 |
| 2.301| 10.8 | 18.9 | 17.6 | 12.0 | 11.1 | -6.5 | -0.9 | 908 | 6915 |
| 2.539| 11.2 | 19.5 | 18.2 | 12.3 | 11.4 | -6.8 | -0.9 | 872 | 6645 |
| 2.894| 11.4 | 20.0 | 18.6 | 12.5 | 11.6 | -7.0 | -0.9 | 846 | 6454 |
| 3.013| 11.5 | 20.0 | 18.6 | 12.5 | 11.6 | -7.0 | -0.9 | 844 | 6442 |
| 3.131| 11.4 | 20.0 | 18.6 | 12.5 | 11.6 | -7.0 | -0.9 | 846 | 6454 |
| 3.486| 11.2 | 19.5 | 18.2 | 12.3 | 11.4 | -6.8 | -0.9 | 872 | 6645 |
| 3.724| 10.8 | 18.9 | 17.6 | 12.0 | 11.1 | -6.5 | -0.9 | 908 | 6915 |
| 4.316| 9.4 | 16.3 | 15.3 | 10.6 | 9.9 | -5.4 | -0.7 | 1097 | 8311 |
| 4.909| 7.0 | 11.9 | 11.3 | 8.1 | 7.6 | -3.7 | -0.5 | 1583 | 11886 |
| 5.501| 3.6 | 5.9 | 5.7 | 4.2 | 3.9 | -1.7 | -0.2 | 3429 | 25481 |
| 5.975| 0.4 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0 | 0 |
| 6.025| 0.0 | -0.6 | -0.6 | -0.5 | -0.4 | 0.2 | 0.0 | 544 | 4026 |
_____________________________________________________________________________________________________________
Col. A: Net deflection at transfer includes prestressing and beam weight on temporary supports.
Col. B: Net deflection at erection includes prestressing and all dead loads applied before the cast-in-place
pour plus long-time deflection growth of the prestressing and beam weight up to erection
Col. C: Net deflection at completion of construction includes prestressing and all dead loads
plus long-time deflection growth of the prestressing and dead load up to completion
Col. D: Net DL deflection at final includes prestressing, all dead loads, and sustained live loads,.
plus long-time deflection growth.
Col. E: Net total deflection at final includes prestressing, all dead loads, and all live loads,
plus long-time deflection growth.

Live load includes roof load, and fluid weight. Wind and earthquake are not included.
Deflection growth is estimated by use of the PCI suggested multipliers - see the Deflection Multipliers report.
Span/Deflection Limits: DL growth + LL = L / 480 for non-structural attachments
L / 240 otherwise
LL alone = L / 360 for floors
L / 180 for roofs
__________________________________________________________________________________________________________________________________
SUPPORT ROTATIONS, AND CHANGE OF LENGTH AT ALL STAGES
Design Code Used: ACI 318-08
B. Unrestrained Support Rotations at All Stages
(-ve = counter-clockwise rotation, +ve = clockwise rotation)
_____________________________________________________________________________________________________
| | Net Rotation | Change in Rotation |
| Support| Net @ | Net @ | Net @ | Net DL | Net Total | DL growth | LL |
|Location| Transfer | Erection | Completion | @ Final | @ Final | + LL | alone |
| | degrees | degrees | degrees | degrees | degrees | degrees | degrees |
| Column | A | B | C | D | E | E - C | E - D |
_____________________________________________________________________________________________________
| Left | -0.4066 | -0.7355 | -0.7098 | -0.5277 | -0.4992 | 0.2106 | 0.0285 |
| Right | 0.4066 | 0.7355 | 0.7098 | 0.5277 | 0.4992 | -0.2106 | -0.0285 |
_____________________________________________________________________________________________________

C. Unrestrained Longitudinal Change of Length Due to Creep and Shrinkage


(-ve = shortening, +ve = elongation)
Elastic Shortening = -1.20 mm
__________________________________________________________________________________________________
| | Total Change of Length (after elastic shortening) | Difference in Change |
| | | Erection |Completion| Final | | to Compl.| to Final | to Final |
| | | mm | mm | mm | | mm | mm | mm |
| | | B | C | D | | C - B | D - C | D - B |
__________________________________________________________________________________________________
| Creep | | -0.96| -1.36| -2.56| | -0.40| -1.21| -1.60|
| Shrink.| | -1.61| -2.46| -3.35| | -0.85| -0.89| -1.73|
| Total | | -2.57| -3.82| -5.91| | -1.24| -2.09| -3.33|
__________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________

FLEXURAL DESIGN CHECK

Design Code Used: ACI 318-08


used: for precast beam = 0.760 , for cast-in-place pour = 0.818

Modulus of Rupture of Precast Concrete, fr = 3.94 MPa (tension)

______________________________________________________________________________________________________________________
| | Factored | Design | Cracking | Minimum * | Depth in | Net Tensile| Flexural | | Notes & |
| | Moment | Strength | Moment | Required | Compression| Strain |Classication| | Warnings |
| x | Mu | Mn | Mcr | Strength | c | | | | |
| m | kNm | kNm | kNm | kNm | mm | | | | |
______________________________________________________________________________________________________________________
| 0.000| 0.0 | 0.1 | 40.8 | 0.0 | 0.8 | 0.8617|Tension | 0.75| |
| 0.050| 0.0 | -1.2 | 24.8 | 0.0 | 1.6 | 0.0551|Tension | 0.75| |
| 0.524| 27.5 | 104.5 | 161.5 | 55.0 | 22.1 | 0.0302|Tension | 0.75| |
| 1.117| 55.1 | 165.9 | 188.1 | 110.3 | 33.6 | 0.0188|Tension | 0.80| |
| 1.709| 75.3 | 219.4 | 187.9 | 150.6 | 41.6 | 0.0146|Tension | 0.86| |
| 2.301| 88.0 | 257.4 | 187.8 | 176.1 | 47.5 | 0.0125|Tension | 0.90| |
| 2.539| 91.0 | 257.4 | 187.8 | 182.0 | 47.5 | 0.0125|Tension | 0.90| |
| 2.894| 93.3 | 257.4 | 187.7 | 186.5 | 47.5 | 0.0125|Tension | 0.90| |
| 3.013| 93.4 | 257.4 | 187.7 | 186.8 | 47.5 | 0.0125|Tension | 0.90| |
| 3.131| 93.3 | 257.4 | 187.7 | 186.5 | 47.5 | 0.0125|Tension | 0.90| |
| 3.486| 91.0 | 257.4 | 187.8 | 182.0 | 47.5 | 0.0125|Tension | 0.90| |
| 3.724| 88.0 | 257.4 | 187.8 | 176.1 | 47.5 | 0.0125|Tension | 0.90| |
| 4.316| 75.3 | 219.4 | 187.9 | 150.6 | 41.6 | 0.0146|Tension | 0.86| |
| 4.909| 55.1 | 165.9 | 188.1 | 110.3 | 33.6 | 0.0188|Tension | 0.80| |

Engineer: Company:
File: hc200 design.con 4 of 5 Tue Oct 17 15:15:50 2017
Summary Report

Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - EVALUATION USE ONLY
Project:
Problem:

| 5.501| 27.5 | 104.5 | 161.5 | 55.0 | 22.1 | 0.0302|Tension | 0.75| |


| 5.975| 0.0 | -1.2 | 24.8 | 0.0 | 1.6 | 0.0551|Tension | 0.75| |
| 6.025| 0.0 | 0.1 | 40.8 | 0.0 | 0.8 | 0.8617|Tension | 0.75| |
______________________________________________________________________________________________________________________
Points of Maximum and Minimum Factored Moment
| 3.013| 93.4 | 257.4 | 187.7 | 186.8 | 47.5 | 0.0125|Tension | 0.90| |
| 5.975| 0.0 | -1.2 | 24.8 | 0.0 | 1.6 | 0.0551|Tension | 0.75| |
Points of Maximum Ratio of Factored Moment to Design Strength
| 3.013| 93.4 | 257.4 | 187.7 | 186.8 | 47.5 | 0.0125|Tension | 0.90| |
| 5.975| 0.0 | -1.2 | 24.8 | 0.0 | 1.6 | 0.0551|Tension | 0.75| |
______________________________________________________________________________________________________________________
* Minimum Strength Only Checked at Points of Maximum and Minimum Moment.

Engineer: Company:
File: hc200 design.con 5 of 5 Tue Oct 17 15:15:50 2017

You might also like