Professional Documents
Culture Documents
The designers decided to design a motion-based earthquake alarm device in order to detect
earthquakes, especially during the Big One. Usually, the alarm is being turned on by a person to
signal other people. But this time, the device will automatically make a sound and light to alert
people that there is an earthquake. The unique feature of this device was that it has a recorded
voice that will be played and reported about the current intensity of the earthquake every time it
changes. The bulb will also give indication of what the current intensity is.
This study is vital for the advancement of Electronics Engineers in LabVIEW programming
environment and designing systems for the benefit of most. The researchers structuralized a
water level-based emergency light system, specifically developed for calamity purposes. The
project, integrated by LabVIEW programming and NI MyRio, serves as a warning and alert system
to efficiently monitor the critical flood prone areas in real time basis. The component used in this
project was a sonic range finder, which measures the rate of change of water level using the
sonar effect. After the data gathered from the sensor were executed in the LabVIEW program, a
specific LED light will signal the water level status of the area.
In this project, the traffic light will be controlled by the program to be simulated in assembly
language and with the interfacing of the input and output connector which is the parallel
port.
Zarks Burgers Automated Order System has the capacity to execute orders with both
speed and accuracy. By removing human intervention in this phase of the order-handling
process, these systems can lower the number of errors. It is executed through assembly
language.
This documentation aims to demonstrate that Dual Polarity Power Supply can be a tool
for converting 220 Vrms AC voltage with 60Hz frequency to DC voltage ranging from 0V
to 24V having less than 5% ripple factor and load regulation by creating unique schematic
diagram with the use of its essential components such as center tapped transformer,
diodes, capacitors, resistors, Zener Diode and potentiometer embracing the principles
and theories in order that voltage produced is used to power all types of electronic circuits.
THE STUDY ON THE EFFECTS OF THE LOW PASS AND HIGH PASS FILTERS TO
THE OUTPUT SIGNAL
Technological Institute of the Philippines - Quezon City
March 19, 2017
This study is vital for the design of experiment of Audio Amplifier employing Bipolar
Junction Transistor. The researchers conducted a study on the effects of the Low Pass
and High Pass Filters to the Output Signal. The project presented on how the mentioned
Filters affects the output signal of the Amplifier.
SCHOLA COMPANY
Technological Institute of the Philippines - Quezon City
March 6, 2017
The focus of this project was to design an application of operational amplifier in laser
communication link by using C# as its programming language. The system will be using
a transmitter and a receiver. An operational amplifier is used in the receiver module to
amplify the signal coming from the transmitter via Laser. A C# programming language is
used to program the transmitter to convert the data from binary numbers to ON and OFF
state of the Laser. The project can be used in transmitting text messages without relying
on cellular sites. Some calculations, assumptions, and selections were made as a
consideration of a proper and realistic design.
The Operational Amplifier is a component that can amplify and invert voltage through its
high input impedance and high Open loop gain. One of its application is used as
Comparator. Together with the Arduino a platform with an open-source electronics
interface based on easy-to-use hardware and software that has been the brain of several
number of projects, from daily objects to complex instruments with the use of Arduino
Software IDE, the water level indicator with security laser was made with an objective to
monitoring the water level of any bodies of water and Security alarm around the vicinity.
In this paper, Water Level Indicator with Security Laser through the use of Light
Dependent Resistor using Operational Amplifier is presented. The project reads a certain
amount of water level then the output will be displayed digitally through 7 segment display
and will alarm when it reaches the critical levels. Once the critical level has been reached,
the laser will be ready to detect anyone might crossover the invisible ray within the critical
area which makes the LED lighten up. This project uses Aceduino (as alternative for
Arduino), LM 741, LM358, 555 timer, logic gates 74LS148 and 74LS47, 7 segment
display, buzzer, LED and LDR (Light dependent Resistor).
This case study aims to create a Simple Digital Logic Design (H-Bridge). Specifically, this
aims to: Design a simple motor controller that is used to provide 4 functions to an electric
motor: Forward, Reverse, Brake, and Coast; Build with 4 switches, and allows voltage to
be applied across the motor in either direction; and, aid the given situation by constructing
a logical equation using truth table and K-map.
This case study aims to create a soil moisture analyzer with automated watering system
using logic circuits. Specifically, this aims to: Design an adaptive equipment that can
serve as an automated watering system; Analyze and monitor content of the soil;
Produce an automated watering system dependent on the moisture content of the soil;
and, aid the given situation by constructing a logical equation using truth table and K-
map.
This case study generally aims to develop a voltage level indicator microcontroller-based
oscilloscope using ACEduino, decoder and demultiplexer. Specifically, this aims to:
Convert the AC analog signal to digital 4-bit binary by using ACEduino; Utilize the use of
demultiplexer by converting 4 bits to 8 bits to determine the real-time amplitude of the AC
signal; Provide LED indicators to represent the real-time amplitude of the waveform,
specifically the single output of the demultiplexer; Employ decoder in the circuit to convert
4 bits BCD to 8 bits; and , use a seven-segment LED display for further visualization aid
of the real-time amplitude of the input signal.