You are on page 1of 20

Reason for the Job

Operational test to verify correct operation of mechanical control between


yaw damper system 2 and rudder

Equipment and Materials


Electrical Ground Power Unit - 3-Phase, 115/200 V, 400 Hz, 90 kVA
Cart-Hydraulic Ground Power Supply
Cable Holding Strap
Electronic Rack-Ventilation

Reason for the Job AMM-32-00-00/501


Continuity test of module unit proximity detector.
Equipment and Materials
Electrical Ground Power Unit - 3-Phase, 115/200 V, 400 Hz, 90 kVA
Cable Holding Strap
Electronic Rack-Ventilation

Reason for the Job AMM-52-10-11/601


General visual check of fuselage doors and panels for satisfactory
condition.
Equipment and Materials
Electrical Ground Power Unit - 3-Phase, 115/200 V, 400 Hz, 90 kVA
Cable Holding Strap
Electronic Rack-Ventilation
Variable Platform 3.5 to 16.5 m (11 ft. 6 in. to 54 ft. 2 in.)
Support Struts UDC Door-98A52308002222
Set-Safety Pin Emergency Control Handle-98A52108003000
Safety Lock Cargo Compartment Door Actuator-98A52307567001 or
98A52307628000
Lock wire CorrosionResistant Steel 0.63 mm (0.03 in) Dia
Circuit Breaker Safety Clips
Safety Pin-Passenger Door Damper and Emergency Operation Cylinder

Reason for the Job AMM-215100/601


Check cooling air inlets/outlets for general condition.
Equipment and Materials
Access Platform, 1.5 m (4 ft. 11 in.)
Solvent Lotoxane
Lint free Cloth
Inspection Light

Reason for the Job AMM 236000/601


Check presence of all static dischargers located on wing zones 500/600
and empennage zone 300.
Equipment and Materials
Variable Platform 3.5 to 16.5 m (11 ft. 6 in. to 54 ft. 2 in.)

Reason for the Job AMM-28-24-00/500


Check APU fuel duct drain mast holes (at frame 53) for obstruction and
for fuel leakage with tank 1 booster pump operating.
Equipment and Materials
Electrical Ground Power Unit - 3-Phase, 115/200V, 400Hz, 90kVA
Cable Holding Strap
Electronic Rack-Ventilation

Reason for the Job AMM-34-11-15/601


General visual check of pitot probes, static ports, temperature sensors
and angle of attack sensors for security of attachment, satisfactory
condition and clear appearance of markings and placards.
Equipment and Materials
Access Platform 2.5 m (8 ft. 2 in.)

Reason for the Job AMM 561112/601


Detailed visual inspection of all cockpit windows from inside.
Equipment and Materials
Access Platform 2.5 m (8 ft. 2 in.)
Variable Platform, 3.5 m to 16.5 m (11 ft. 6 in. to 54 ft. 2 in.)
Sponge
Lint free Cloth
Chamois Leather
Special Material- Mat. No. 10-002
Reason for the Job
Operational test of slat retraction interlock (mechanical control).
Equipment and Materials
Electrical Ground Power Unit - 3- phase, 115/200 V, 400 Hz, 90 Kva
Hydraulic Ground Power Unit, 150 L/min (36.6 US Gpm)
Access Platform, 1.8 m (5 ft. 11 in.)
Headset - Interphone with Extension Cord

Reason for the Job AMM-27-38-00/501


Operational test of slat asymmetry monitoring circuit.
Equipment and Materials
Electrical Ground Power Unit - 3- phase, 115/200 V, 400 Hz, 90 Kva
Access Platform, 1.80 m (5 ft. 11 in.)
Connector - Pressurizing Hydraulic Reservoir-97A29102035000
Connector - Depressurizing Hydraulic Reservoir-97A29102062000
Compressed Air Source
Container, 5.0 L (1.3 US gal)
Hydraulic Ground Power Unit, 150 L/min (36.6 US Gpm)
Access Platform, 1.8 m (5 ft. 11 in.)
Headset - Interphone with Extension Cord

Reason for the Job


General visual inspection of cargo loading system latches end stops,
guides and rollers for general condition, obvious damage and proper
attachment
Equipment and Materials
Electrical Ground Power Unit - 3- phase, 115/200 V, 400 Hz, 90 Kva
Access Platform 2.8 m (9 ft. 2 in.)
Access Platform 2.5 m (8 ft. 2 in.)
Safety Lock. Cargo Compartment Door Actuator

Reason for the Job


Check all internal flight compartment and passenger (MDC) compartment
lights (including fasten seat belt/no smoking signs) for burnt out bulbs,
missing spare bulbs and fuses (spare box).
Equipment and Materials
Electrical Ground Power Unit - 3- phase, 115/200 V, 400 Hz, 90 Kva
Access Platform 2.8 m (9 ft. 2 in.)
Access Platform 2.5 m (8 ft. 2 in.)
Safety Lock. Cargo Compartment Door Actuator

Reason for the Job


Check net and attachments for satisfactory condition.
Equipment and Materials
Flash Light
Stepladder

Reason for the Job


Check pressure of portable fire extinguisher at gage in cabin area.

Reason for the Job


Check net and attachments for satisfactory condition.
Equipment and Materials
Electrical Ground Power Unit - 3-Phase, 115/200 V, 400 Hz, 90 kVA
Access Platform 2.8 m (9 ft. 2 in.)
Vacuum Cleaner
Cable Holding Strap - 98A24403000000

Reason for the Job AMM 21-23-00/601


General visual check of external battery cooling orifices for
obstruction.
Equipment and Materials
Electrical Ground Power Unit - 3-Phase, 115/200 V, 400 Hz, 90 kVA
Access Platform 2.8 m (9 ft. 2 in.)
Vacuum Cleaner
Cable Holding Strap - 98A24403000000

Reason for the Job AMM 29-14-13/301


Check by-pass opening indicator on pressurization line filter of "ENG 1"
air bleed is not protruding.

Equipment and Materials


Access Platform, 1.8 m
Reason for the Job AMM 21-23-00/601
Check by-pass opening indicator on pressurization line filter of "ENG 1"
air bleed is not protruding.

Equipment and Materials


Access Platform, 1.8 m

Reason for the Job AMM 29-14-13/301


Remove, inspect and clean Green return manifold filter element (1066).

Equipment and Materials


Access Platform, 2.6 m
Torque Wrench up to 8.0 m.daN (59 lbf. ft.)
Blanking Plugs/Caps
Lock wire, Corrosion Resistant Steel, 0.8 mm (0.032 in.) Dia
O-Ring (Ref. IPC 29-11-03 Fig. 7A Item 283)- NAS1611-016
O-Ring (Ref. IPC 29-11-03 Fig. 7A Item 80)- NAS1612-12
Filter Element (as required) (Ref. IPC 29-11-03 Fig. 7A Item 280A)-
CG0203103461C00
Solvent- Mat. No. 11-003

Reason for the Job AMM 25-51-00/701


Vacuum cleaning of FWD cargo conveyance system.
General visual inspection of FWD cargo latches, end stays and guides.

Equipment and Materials


Electrical Ground Power Unit 3-Phase, 115/200 V, 400 Hz, 90 kVA
Circuit Breaker Safety Clips
Access Platform 2.5 m (8 ft. 2 in)
Safety Lock Cargo Compartment Door-98A52307567001
Vacuum Cleaner
Cleaning Equipment (Sponge, Brush, Lint-Free Cloth)
Non-Metallic Scraper
Cable Holding Strap

Reason for the Job AMM 25-51-00/701


Vacuum cleaning of AFT cargo conveyance system.
General visual inspection of AFT cargo Latches, and stops and guides.

Equipment and Materials


Electrical Ground Power Unit 3-Phase, 115/200 V, 400 Hz, 90 kVA
Circuit Breaker Safety Clips
Vacuum Cleaner
Access Platform 2.5 m (8ft. 2 in.)
Non Metallic Scraper

Reason for the Job AMM 27-51-65


Check jettison discharge nozzle (At flap track no. 5) for general
condition.

Equipment and Materials


Access Platform, 2.8 m (9 ft. 2 in.)

Reason for the Job AMM 28-11-00


Check fuel tank areas for fuel leaks especially in areas of pylon
attachment and inboard of rib 1.

Equipment and Materials


Access Platform, 2.8 m (9 ft. 2 in.)
Access Platform, 1.80 m (5 ft. 11 in.)

Reason for the Job AMM 72-65-00/600


Visual inspection of LH link mount spherical bearing for evidence ofg
wear and mount bracket for cracking.

Equipment and Materials


Access Platform, 1.5 m (4 ft. 11 in.)
Circuit Breaker Safety Clips
Pump Hydraulic- 2C6983

Reason for the Job


Bore scope inspection of combustion liner for indication of fishmouth
seal failure (inner). Inspect HPT nozzle vane leading edge at 5 to 6
oclock position for indication of discoloration and burning.

Equipment and Materials


Access Platform, 1 m (3 ft. 1 in.)
Access Platform 2.2 m (7ft. 2 in.)
Bore scope set(Ref TEM 72-51-00)
Torque wrench up to 1.8 daN*m (160 lbf. in.)
Anti Size Compound GP 460- Mat.-No C02-058
Washer-9609M43P01
Washer-9609M43P03
Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips

Reason for the Job AMM 75-22-01/601


Inspect the 7TH stage air manifold/tube for cracks, loose or worn clamps
and brackets.

Equipment and Materials


Access Platform, 1.5 m (4 ft. 11 in.)
Magnifying Glass, 10 X
Bright Light
Torque Wrench, up to 1.7 m.daN (175 lbf.in.)
Wrench Set, Spanner Airtube Nuts-2C6352
Anti-Seize Compound, Fel-Pro C 601, MIL-T-5544- Mat. No. C02-001
Circuit Breaker Safety Clips
Pump Hydraulic-2C6983
Access Platform, 1.5 m (4 ft. 11 in.)

Reason for the Job AMM 72-32-00/201


Bore scope inspection (ports B1-6 and B1-7) of HPC vane stage 6 and 7
trailing edge root for notches.

Equipment and Materials


From Olympus. Flexible Bore scope, End viewing (Side Viewing
optional) 6 mm Diameter * 2m nominal long.
Olympus Model ILV or Equivalent, High Powered Light Source.
Spanner Wrench Set. To Remove Stage 7 manifold.
Access Platform, 1.5 m (4 ft. 11 in.)
Torque Wrench up to - 1.7 m.daN (150 lbf.in.)
Lock wire, Corrosion Resistant Steel, 0.8 mm (0.032 in.) Dia.
O-Ring- MS 9873-021
Anti-Seize Compound GP 440 - Mat. No. C02-058
Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic
Circuit Breaker Safety Clips
Reason for the Job AMM 72-33-00/201
Bore scope inspection (ports B1-6 and B1-7) of HPC vane stage 6 and 7
trailing edge root for notches.
Equipment and Materials
From Olympus. Flexible Bore scope, End viewing (Side Viewing
optional) 6 mm Diameter * 2m nominal long - IF6D3-20
Olympus Model ILV or Equivalent, High Powered Light Source.
Spanner Wrench Set. To Remove Stage 7 manifold-2C6352G02
Access Platform, 1.5 m (4 ft. 11 in.)
Torque Wrench up to - 1.7 m.daN (150 lbf.in.)
Lock wire, Corrosion Resistant Steel, 0.8 mm (0.032 in.) Dia.
O-Ring- MS 9873-021
Anti-Seize Compound GP 440 - Mat. No. C02-058
Circuit Breaker Safety Clips
Pump Hydraulic-2C6983
Access Platform, 1.5 m (4 ft. 11 in.)

Reason for the Job AMM 72-33-00/200


Visual inspection of circumferential rib of fwd HPC case for cracks,
nicks, dents gouges and scratches.

Equipment and Materials


Access Platform, 1.5 m (4 ft. 11 in.)
Circuit Breaker Safety Clips
Pump Hydraulic-2C6983

Reason for the Job AMM 72-33-00/200


Visual inspection of rear compressor case flanges and welt joints for
cracking.

Equipment and Materials


Access Platform, 1.5 m (4 ft. 11 in.)
Circuit Breaker Safety Clips
Pump Hydraulic-2C6983

Reason for the Job AMM 72-33-00/200


Detailed visual inspection of compressor rear frame forward flanges
(without doublers installed) for cracks.

Equipment and Materials


Access Platform, 1.5 m (4 ft. 11 in.)
Circuit Breaker Safety Clips
Pump Hydraulic-2C6983

Reason for the Job AMM 72-31-00/201


Boroscope inspection of compressor rotor blades stage 14 for domestic
object damage.
Equipment and Materials
Bore scope Set-2C6388G03
Access Platform, 1.5 m (4 ft. 11 in.)
Torque Wrench up to 1.7 m.daN (150 lbf.in.)
Lock wire, Corrosion Resistant Steel, 0.8 mm (0.032 in.) Dia.
Pneumatic Powered Core Turning Tool- MSE-44
O-Ring- MS 9873-021
O-Ring- R149P156
Gasket-9185M83P01
Anti-Seize Compound GP 440- Mat. No. C02-058
Lubricant- C02-007
Rotor drive N2,3/4 in.2
Circuit Breaker Safety Clips
Pump Hydraulic-2C6983

Reason for the Job AMM 72-41-00/201


Bore scope inspection of combustion liner assembly and dome area in
accordance with GE NTM.
Equipment and Materials
Access Platform, 1.5 m (4 ft. 11 in.)
Access Platform 1 m (3 ft. 1 in.)
Access Platform 2.2 m (3 ft. 2 in.)
Torque Wrench up to 1.8 dN*m (160 lbf. in.)
Bore scope Set (Ref. GE-NTM 72-40-00/7)- 2C6388G03
Anti Size Compound GP 440 - Mat-No C02-058
Corrosion Resistant Lock wire 0.8 mm (0.0321 in.)
Washer-Flat-9609M43P03
Circuit Breaker Safety Clips
Pump Hydraulic-2C6983

Reason for the Job AMM 72-22-00/601


Detailed visual inspection of:
- Fan rotor blades (with particular attention to blade leading and
trailing edges, tips and mid span shrouds) for damage
- Low pressure compressor I.G.V.
Equipment and Materials
Access Platform, 1.5 m (4 ft. 11 in.)
Spot Light
Inspection Mirror
Rubber mat

Reason for the Job AMM 72-22-00/601


Bore scope inspection of combustion liner for indication of fishmouth
seal failure (inner). Inspect HPT nozzle vane leading edge at 5 to 6
oclock position for indication of discoloration and burning.
Equipment and Materials
Access Platform, 1.5 m (4 ft. 11 in.)
Access Platform, 1 m (3 ft. 1 in.)
Access Platform 2.2 m (7ft. 2 in.)
Bore scope set(Ref TEM 72-51-00)- 2C6388
Torque wrench up to 1.8 daN*m (160 lbf. in.)
Anti Size Compound GP 460- Mat.-No C02-058
Washer-9609M43P01
Washer-9609M43P03
Corrosion Resistant Lock wire 0.8 mm (0.0321 in.)
Circuit Breaker Safety Clips
Pump Hydraulic-2C6983

Reason for the Job AMM 72-51-00/601


Bore scope inspection of HPT nozzle stage 1 (HPTN-1) via combustion ports
and ports between 5 and 7 oclock position.
Equipment and Materials
Bore scope Set
Access Platform 1 m (3 ft. 1 in.)
Access Platform, 2.2 m (7 ft. 2 in.)
Torque Wrench up to - 1.8 m*daN (160 lbf.in.)
Anti-Seize Compound GP 460- Mat. No. C02-058
Circuit Breaker Safety Clips
Pump Hydraulic-2C6983
Access Platform, 1.5 m (4 ft. 11 in.)
Reason for the Job AMM 72-53-00/201
Bore scope inspection of HP turbine rotor blades stage 1.
Equipment and Materials
Bore scope Set
Access Platform, 1.5 m (4 ft. 11 in.)
Torque Wrench up to - 1.8 m.daN (160 lbf.in.)
3/4 in. Square Drive Wrench (Rotor Cranking)
Lock wire, Corrosion Resistant Steel, 0.8 mm (0.032 in.) Dia.
Anti-Seize compound, MIL-L-5544- Mat. No. C02-001
O-Ring Gasket - J221P156/9185M83P01
Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips

Reason for the Job AMM 72-53-00/201


Bore scope inspection of HP turbine rotor blades stage 2.
Pay particular attention to blade leading edge for damage indicating
possible stage 2 nozzle defects such as bending or torsion or sag
(Repaired stg. 2 nozzle assemblies).
Equipment and Materials
Bore scope Set
Access Platform, 1.5 m (4 ft. 11 in.)
Torque Wrench up to - 1.8 m.daN (160 lbf.in.)
3/4 in. Square Drive Wrench (Rotor Cranking)
Lock wire, Corrosion Resistant Steel, 0.8 mm (0.032 in.) Dia.
Anti-Seize compound, MIL-L-5544- Mat. No. C02-001
Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips
O-Ring- I221P156
Gasket -9185M83 P01

Reason for the Job


NDT (eddy current) of the HPTR thermal shield.
Equipment and Materials
Bore scope Set
Access Platform, 1.5 m (4 ft. 11 in.)
Pneumatic Powered Core Turning Tool- MSE-44
Metal Gasket- GE P/N 1100M65G128- VIN 63GA0021
Kit, HPT Thermal Shield ON-Wing Eddy Current Inspection with a

- Forster Defectometer Model 2.835, 2.836 or 2.164


- P/N 6196; Eddy Current Probe
- SGP-004; Calibration Standard with a Calibration Notch Electrodischarge
mMchined into ist Surface
-15-076C; Thermometer 0 to 230F (Fisher Scientific)

Reason for the Job AMM 72-57-00/201


Bore scope inspection of stage 1 LPT blade retainers for rubs.
Equipment and Materials
Access Platform, 1.5 m (4 ft. 11 in.)
Fiberscope Set, Flexible 6mm
Guide Tube, Bore scope Probe-2C6948P01
Torque Wrench, up to 1.7 m.daN (150 lbf.in.)
Lock wire, Corrosion Resistant Steel 0.032 in. (0.80 mm) Dia.
Compound, Anti-Seize, GP460- Mat. No. C02-058
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips

Reason for the Job AMM 72-54-00/200


Visual inspection of the engine turbine mid frame (TMF):
- Liner for clocking.
- Hat section and T/C boss for cracking.

Equipment and Materials


Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips

Reason for the Job AMM 72-41-00/601


Bore scope inspection of combustion liner assembly and dome area in
accordance with GE NTM.
Equipment and Materials
Access Platform, 1.5 m (4 ft. 11 in.)
Access Platform 1 m (3 ft. 1 in.)
Access Platform 2.2 m (3 ft. 2 in.)
Torque Wrench up to 1.8 dN*m (160 lbf. in.)
Bore scope Set (Ref. GE-NTM 72-40-00/7)- 2C6388G03
Anti Size Compound (GP 460)- Mat-No C02-058
Washer-Flat-9609M43P03
Corrosion Resistant Lock wire 0.8 mm (0.0321 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips

Reason for the Job AMM 72-57-00/201


Bore scope detailed visual inspection of stage 4 blade tip interlock for
wear.
Equipment and Materials
Access Platform 1.5 m (5 ft.)
Bore scope
Torch Lamp
Circuit Breaker Safety Clips

Reason for the Job AMM 72-54-00/200


Visual inspection of the engine turbine mid frame (TMF):
- Liner for clocking.
- Hat section and T/C boss for cracking.
Equipment and Materials
Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips

Reason for the Job AMM 75-22-01/601


Inspect the 7TH stage air manifold/tube for cracks, loose or worn clamps
and brackets.
Equipment and Materials
Magnifying Glass, 10 X
Bright Light
Torque Wrench, up to 1.7 m.daN (175 lbf.in.)
Wrench Set, Spanner Airtube Nuts-2C6352
Anti-Seize Compound, Fel-Pro C 601, MIL-T-5544- Mat. No. C02-001
Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips
Reason for the Job AMM 73-31-00/201
Bore scope inspection of compressor rotor blades stage 14 for domestic
object damage.
Equipment and Materials
Magnifying Glass, 10 X
Bore scope Set-2C6388G03
Access Platform, 1.5 m (4 ft. 11 in.)
Torque Wrench up to 1.7 m.daN (150 lbf.in.)
Lock wire, Corrosion Resistant Steel, 0.8 mm (0.032 in.) Dia.
Rotor drive N2,3/4 in.2
Pneumatic Powered Core Turning Tool- MSE-44
O-Ring- MS 9873-021
O-Ring- R149P156
Gasket-9185M83P01
Anti-Seize Compound 440- Mat. No. C02-058
Lubricant- C02-007
Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips

Reason for the Job AMM 72-65-00/600


Visual inspection of LH link mount spherical bearing for evidence ofg
wear and mount bracket for cracking.
Equipment and Materials
Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips

Reason for the Job AMM 72-57-00/201


Bore scope/detailed visual inspection of stage 4 blade tip interlock for
wear.
Equipment and Materials
Access Platform 1.5 m (5 ft.)
Borescope-2C6388G03
Torch Lamp
Circuit Breaker Safety Clips

Reason for the Job AMM 72-57-00/201


Detailed visual inspection of LP turbine rotor blades for damage (last
stage).
Equipment and Materials
Access Platform 1.5 m (5 ft.)
Torch Lamp
Circuit Breaker Safety Clips

Reason for the Job AMM 29-00-00/301


Check that EDP case drain filters clogging indicators are not protruding.

Reason for the Job AMM 72-57-00/201


Detailed visual inspection of LP turbine rotor blades for damage (last
stage).
Equipment and Materials
Access Platform 1.5 m (5 ft.)
Torch Lamp
Circuit Breaker Safety Clips

Reason for the Job


Detailed visual inspection of engine forward mount side links.
Equipment and Materials
Access Platform, 2.2 m (7 ft. 2 in.)
Inspection Mirror
Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips

Reason for the Job AMM-72-21-00/601


Detailed visual inspection of:
- fan rotor blades (with particular attention to blade leading and
trailing edges, tips and mid span shrouds) for damage
- Low pressure compressor I.G.V..
Equipment and Materials
Access Platform, 1.5 m (4 ft. 11 in.)
Spot Light
Inspection Mirror
Rubber mat

Reason for the Job AMM-29-00-00/301


Check that EDP case drain filters clogging indicators are not protruding.
Reason for the Job AMM-49-44-11/601
General visual inspection of APU electrical starter motor brushes and
brush leads for satisfactory condition, wear, corrosion and damage leads.
Equipment and Materials
Access Platform 6.0 m (19 ft. 8 in.)
Depth Micrometer

Reason for the Job AMM-49-42-12/601


Remove igniters plugs
Clean plugs
Detailed visual inspection of igniters plugs. For ceramic cracking and
aluminium spray deposits
Inspect threads for corrosion
Install igniters plugs.
Equipment and Materials
Access Platform 6.0 m (19 ft. 8 in.)
Circuit Breaker Safety Clips
Torque Wrench up to - 1.7 m.daN (150 lbf.in.)
Abrasive Cabinet Plug Cleaner or Stiff-Bristle Brush
Plastic Bag
Lock wire Corrosion Resistant Steel, 0.8 mm (0.032 in.) Dia
High Temperature Compound MIL-A-907 - Mat. No. 04-014
Solvent- Mat. No. C04-002
White Spirit PD 680- Mat. No. 11-002
Gasket-6800611
Gasket-1230609-13

Reason for the Job AMM-49-16-14/401


Remove air intake duct or remove inspection plug from bottom of inlet
cylinder.
Detailed visual inspection of LP compressor first stage rotor blades for
cracks, corrosion and FOD or perform bore scope inspection of LP
compressor first stage rotor blades.
Check LP compressor wheel stage 1 for free.
Equipment and Materials
Access Platform 6.0 m (19 ft. 8 in.)
Circuit Breaker Safety Clips
Flashlight
Inspection Mirror
Torque Wrench up to - 1.7 m.daN (150 lbf.in.)
Bore scope 8 mm (0.30 in.) Dia

Reason for the Job AMM-49-52-00/601


Detailed visual inspection of fan impeller for FOD and evidence of oil
leaks (no visible damage acceptable).
Inspect inlet duct for general condition.
Equipment and Materials
Access Platform, 6.0 m (19 ft. 8 in.)
Circuit Breaker Safety Clips
Flashlight
Inspection Mirror
Torque Wrench up to - 1.7 m.daN (150 lbf.in.)
Solvent Lotoxane- Mat. No. 11-026
Adhesive Sealant- Mat. No. 08-004
Gasket- NSA8210-180

Reason for the Job AMM-12-22-52/001


Lubrication of girt bar sliders and fittings.
Equipment and Materials
Access Platform 4.45 m 14 ft. 7 in.)
Safety Pin-Passenger Door Damper and Emergency Operation Cylinder-
701-2978000
Set-Safety Pin Emergency Control Handle-98A52108003000
Lock wire Corrosion-Resistant Steel 0.63 mm 0.03 in. Dia)
Circuit Breaker Safety Clips
Silicone Grease MIL-G-46886- Mat. No. 04-017
White Spirit PD 680- Mat. No. 11-002
Corrosion Preventive Compound- Mat. No. 15-004

Reason for the Job AMM-12-12-29


Check fluid level of hydraulic tanks (Green, Blue, and Yellow).
Equipment and Materials
Access Platform 4.45 m 14 ft. 7 in.)
Electrical Ground Power Unit - 3-Phase, 115/200 V, 400 Hz, 90 Kva
Access Platform, 2.1 m (8 ft. 11 in.)
Connector-Pressurizing Hydraulic Tank-97A29102035000
Unit-Topping up Hydraulic Tank-99A29001006000
Access Platform 2.1 m (6 ft. 11 in.)
Containers Fluid Recovery
Hydraulic Fluid- Mat. No. 02-003
Cable Holding Strap-98A24403000000
Hydraulic Ground Power Unit, 150 L/min (36.6 US Gpm)
Access Platform, 1.8 m (5 ft. 11 in.)
Headset - Interphone with Extension Cord

Reason for the Job AMM-12-12-32/001


Check fluid level in brake reservoir and refill if necessary.
Equipment and Materials
Access Platform, 6.0 m (19 ft. 8 in.)
Wheel Chocks
Vinyl Hose
Hydraulic Fluid Container
Unit-Filling Aircraft Brake System-98A29001001000
Hydraulic Fluid NSA-307-110- Mat. No. 02-003

Reason for the Job AMM-12-22-27/001


Lubrication of following items:

A. Ball nuts of screw jacks 1 to 6.


B. Carriage rollers of flap track 1 to 6.
C. Rubbing pads (carriage side location) track No. 1 only.
Equipment and Materials
Access Platform, 6.0 m (19 ft. 8 in.)
Electrical Ground Power Unit - 3-Phase, 115/200 V, 400 Hz, 90 kVA
Access Platform, 2.8 m (9 ft. 2 in.)
Access Platform, 1.8 m (5 ft. 11 in.)
Tool-Locking, Flap and Slat Control Lever-98A27901022000
Grease Gun

Synthetic Grease, MIL-G-23827- Mat. No. 04-004


ARMNA G4789- Mat. No. 04-024
White Spirit, PD-680 Type I- Mat. No. 11-002

Reason for the Job AMM-12-22-32/001


Clean and lubricate following points:
- Bogie beam articulation
- Pitch damper attach points
- Brake bars attach points
Equipment and Materials
Access Platform, 6.0 m (19 ft. 8 in.)
Grease Gun Assembly-90A79003000000
Access Platform 2.1 m (6 ft. 11 in.)
Synthetic Grease MIL-G-23827- Mat. No. 04-004
Water Repellent Protective Film MIL-C-81309- Mat. No. 15-004
White Spirit PD 680- Mat. No. 11-002
Lint free Cloth
Electrical Ground Power Unit - 3-Phase, 115/200 V, 400 Hz, 90 kVA
Access Platform 1.50 m (4 ft 11 in.)
Safety Barriers
Safety Collars NLG- C47281
Safety Collars MLG- D46237

Reason for the Job AMM-12-13-80/001


Oil change of pneumatic starter.
Equipment and Materials
Filling Syringe
Torque Wrench up to-1.7 m.daN (150 lbf. in.)
Corrosion Resistant Steel Lock wire Dia 0.8 mm
Packing, Filler Plug- S9413-012
Packing, Drain Plug- MS35769-9
Packing, Magnetic Plug- S9413-008
Oil-Engine, MIL-L-23699- Mat. No. C02-019
Access Platform, 1.5 m (4 ft. 11 in.)
Pump Hydraulic-2C6983
Circuit Breaker Safety Clips

Reason for the Job AMM-2411118/401


Check oil level of constant speed drive and replenish if necessary.
Check CSD scavenge filter and charge filter clogging indicators are not
protruding (as applicable).
Check manually the QAD ring for evidence of play.
Equipment and Materials
Filling Syringe
Tank-Engine Oil Filling Up-98A12001017000
Torque Wrench up to - 1.7 m.daN (150 lbf.in.)
33 Micron Filter
Synthetic Oil MIL-L-23699- Mat. No. 03-002
Reason for the Job AMM-2411118/401
Removal, inspection and cleaning of surge air valve filter and screen.
Equipment and Materials
Variable Platform 3.5 to 16.5 m (11 ft. 6 in. to 54 ft. 2 in.)
Packing- S8990-605
Washer- S8157N231-025
Washer-116702-1
Lock wire Corrosion Resistant Steel 0.6 mm 0.024 in.) Dia
Solvent- Mat. No.11-002
Circuit Breaker Safety Clips

Reason for the Job AMM-2411118/401


Removal, inspection and replacement of oil filter.
Removal of chip detector(magnetic plug contamination).
Equipment and Materials
Variable Platform 3.5 to 16.5 m (11 ft. 6 in. to 54 ft. 2 in.)
Circuit Breaker Safety Clips
Torque Wrench up to - 8.0 m.daN (59 lbf.ft.)
Blanking Cap
Strainer Element
Lock wire Corrosion Resistant Steel 1 mm 0.04 in.) Dia.
Packing- S9413-038
Packing- S9413-218
Packing- S9413-565
Packing- S9413-015
Filter Element-3601818-2
Synthetic Oil MIL-L-23699- Mat. No. 03-002
Solvent- Mat. No. 11-026

You might also like