You are on page 1of 2

Schedule of Accreditation

issued by
United Kingdom Accreditation Service
2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK

Calibration UK Ltd
Issue No: 025 Issue date: 28 September 2017
Unit 17 Contact: Mr Tony Cox
Hindley Business Centre Tel: +44 (0)1942-526164
Platt Lane Fax: +44 (0)1942-525335

0463 Hindley E-Mail: tonycox@pullman.co.uk


Wigan Website: www.cal-uk.com
Accredited to WN2 3PA
ISO/IEC 17025:2005
Calibration performed at the above address only

DETAIL OF ACCREDITATION

Measured Quantity Range Calibration and Measurement Remarks


Instrument or Gauge Capability (CMC) Expressed
as an Expanded Uncertainty
(k=2)
LENGTH NOTES

Plain plug gauges (parallel) 1 to 50 diameter 1.0 1 The uncertainty


cylindrical setting standards and 50 to 100 diameter 1.5 on diameter quoted is for the departure
rollers 100 to 150 diameter 2.0 from flatness,
straightness, or
Plain ring gauges (parallel) and 1 to 10 diameter 1.5 squareness, i.e. the
setting standards 10 to 50 diameter 1.0 on diameter distance separating the
50 to 100 diameter 1.5 two parallel planes which
100 to 150 diameter 2.0 just enclose the surface
under consideration.
Plain gap gauges (parallel) 0.5 to 100 diameter 3.0
2. Single start,
100 to 150 diameter 5.0 symmetrical thread forms
only.
Screw plug gauges (parallel) 1 to 100 diameter 3.0 on pitch diameter
including check and setting plugs 3. Includes use of check
See Note 2 plugs for screw rings from
1 mm to 6 mm diameter
Screw ring gauges (parallel) 1 to 100 diameter 5.0 on pitch diameter
See Notes 2 and 3
4. Functional test of size
Screw pitch 0.2 to 8 1.5 using setting plugs
Screw flank angle 0° to 52° 5.0 minutes of arc calibrated with a CMC of
3.0 µm
Screw thread adjustable caliper 1 to 150 diameter See note 4
gauges (parallel) 5. Simple height gauges
- vernier, dial and digital
Length gauges, flat and spherical 0 to 600 1.0 + (8.0 x length in m) instruments designed only
ended for measuring distances
parallel to the beam.
Engineers parallels BS 906:1972 1.5 to 5.0
5 to 50 x 100 x 400 6. Conformance
statements cannot be
Squares made against
Blade type BS 939:2007 specifications whose
50 to 300 3.0 See Note 1 magnitudes are smaller
300 to 450 5.0 than the specified CMC
values

Assessment Manager: DT Page 1 of 2


S c he dul e of Ac c r e di ta ti on
issued by
United Kingdom Accreditation Service
2 Pine Trees, Chertsey Lane, Stai nes -upon-Tham es, TW 18 3HR, UK

0463 Calibration UK Ltd


Accredited to
Issue No: 025 Issue date: 28 September 2017
ISO/IEC 17025:2005

Calibration performed at main address only

Measured Quantity Range Calibration and Measurement Remarks


Instrument or Gauge Capability (CMC) Expressed
as an Expanded Uncertainty
(k=2)
MEASURING INSTRUMENTS
AND MACHINES

Micrometers BS 870:2008
External (including ball and 0 to 600 Heads: 2.0
thread BS 959:2008 Setting and extension rods:
micrometers) 0 to 900 1.0 + (8.0 x length in m)
Internal BS 6468:2008
Depth 0 to 300

Micrometer heads BS 1734:1951 1.0


0 to 50

Bore micrometer (three point) 3 to 150 diameter Overall performance 5.0


and Bore Gauges

Bevel protractors BS 1685:2008 6.0 min of arc


0° to 360°

Height gauges - (Simple) BS EN ISO 13225:2012 Length measurement error (E):


including vernier, dial and digital 0 to 1000 10 + (30 x length in m)
types (See note 5 and note 6)

Vernier caliper, height and depth BS 887:2008 Overall performance


gauges (including digital and dial 0 to 1000 10 + (30 x length in m)
instruments) BS 1643:2008 (withdrawn)
0 to 1000
BS 6365:2008
0 to 600

Dial gauges and dial test BS 907:2008 and BS 2795:1981 1.0


indicators 0 to 50

Feeler gauges BS 957:2008 3.0


0.05 to 1

Steel Rules BS 4372:1968


0 to 1000 15 + (20 x length in m)

Thickness Gauges 0 to 50 Dependent on size and performance


(dial and digital types) Minimum 3.0

Spirit levels BS 958:1968 6.0 seconds of arc


5 seconds of arc to 60 minutes of
arc nominal sensitivity

Vee blocks BS3731:1987 2.5 to 5.0


20 to 150

FORM

Straightedges BS 5204:Part 1:1975 3.0 (see note 1)


Cast iron, Steel and Granite BS 5204:Part 2:1977
0 to 1500

END

Assessment Manager: DT Page 2 of 2

You might also like