You are on page 1of 3

Page 1 of 3 Fastenal Product Standard REV-07

Date: May 25, 2017 USA.STB.B7.ASMBL.P

Stud Bolts, ASTM A193/A193M and ASME SA193/SA193M, Grade B7 Stud with
ASTM A194/A194M and ASME SA194/SA194M Grade 2H Heavy Hex Nut, Plain
Finish, Assembled with 2 nuts, Manufactured in the USA
The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order. If
the order received does not meet these requirements, it may result in a supplier corrective action request, which could jeopardize your
status as an approved vendor. Unless otherwise specified, all referenced consensus standards must be adhered to in their entirety.

D (inch)
Nominal
Major Diameter
Size
Min. Max.
1/4" .2408 .2489
5/16" .3026 .3113
3/8" .3643 .3737
7/16" .4258 .4361
1/2" .4876 .4985
9/16" .5459 .5609
5/8" .6112 .6233
3/4" .7353 .7482
7/8" .8592 .8731
1" .9830 .9980
1-1/8" 1.1079 1.1229
1-1/4" 1.2329 1.2479
1-3/8" 1.3578 1.3728
1-1/2" 1.4828 1.4978
1-5/8" 1.6078 1.6228
1-3/4" 1.7327 1.7477
1-7/8" 1.8577 1.8727
2" 1.9827 1.9977
2-1/4" 2.2326 2.2476
2-1/2" 2.4826 2.4976
2-3/4" 2.7325 2.7475
3" 2.9824 2.9974
3-1/4" 3.2324 3.2474
3-1/2" 3.4824 3.4974
Page 2 of 3 Fastenal Product Standard REV-07

Date: May 25, 2017 USA.STB.B7.ASMBL.P

EL
Effective Length Tolerance
< 12 inch +/- 0.062"
12 < 18 inch +/- 0.125"
18 inch < +/- 0.250"

Stud Specification Requirements:

• Dimensions: See Table Above


• Stud Ends (U length): Both ends of the stud shall be pointed. Points may be flat and
chamfered, rounded or sheared at the manufacturer’s option;
except that the U length shall not exceed 2 thread pitches in length at
each end.
• EL Diameters: Diameters within the Effective Length shall be of full thread
form throughout its entire length and shall conform to System 21,
thread gaging per ASME B1.3
• Material &
Mechanical Properties: ASTM A193/A193M and ASME SA193/193M; B7
• Thread Requirements: ASME B1.1, 2A
- UNC for all stud diameters 1” and smaller
- UN8 for all stud diameters greater than 1”
• Finish: Light Protective Oil
• Product Marking: Grade mark in accordance with ASTM A193/A193M and ASME
SA193/193M:
B7 and manufacturer’s identification symbols shall be applied to one
end of studs 3∕8 in. [10 mm] in diameter and larger. If the available area
is inadequate, the grade symbol may be marked on one end and the
manufacturer’s identification symbol marked on the other end of studs.
• Manufacturer: Manufactured in the USA, from steel melts originating in USA
• Material Test Reports: The MTR must have documented lot traceability, dimensional
results, full chemical test results and full mechanical test results
to the specification(s) above. In addition, the MTR shall be in full
compliance with Fastenal’s MTR Requirements.
Page 3 of 3 Fastenal Product Standard REV-07

Date: May 25, 2017 USA.STB.B7.ASMBL.P

F H
Nominal
Width Across Flats Thickness
Size
Max. Min. Max. Min.
1/4 .500 .488 .250 .218
5/16 .562 .546 .314 .280
3/8 .688 .669 .377 .341
7/16 .750 .728 .441 .403
1/2 .875 .850 .504 .464
9/16 .938 .909 .568 .526
5/8 1.062 1.031 .631 .587
3/4 1.250 1.212 .758 .710
7/8 1.438 1.394 .885 .833
1 1.625 1.575 1.012 .956
1 1/8 1.812 1.756 1.139 1.079
1 1/4 2.000 1.938 1.251 1.187
1 3/8 2.188 2.119 1.378 1.310
1 1/2 2.375 2.300 1.505 1.433
1 5/8 2.562 2.481 1.632 1.556
1 3/4 2.750 2.662 1.759 1.679
1 7/8 2.938 2.844 1.886 1.802
2 3.125 3.025 2.013 1.925
2 1/4 3.500 3.388 2.251 2.155
2 1/2 3.875 3.750 2.505 2.401
2 3/4 4.250 4.112 2.759 2.647
3 4.625 4.475 3.013 2.893
3 1/4 5.000 4.838 3.252 3.124
3 1/2 5.375 5.200 3.506 3.370

Nut Specification Requirements:

• Dimensions: ASME B18.2.2 Heavy Hex


• Thread Requirements: ASME B1.1, 2B
- UNC for all stud diameters 1” and smaller
- UN8 for all stud diameters greater than 1”
• Nut Material &
Mechanical Properties: Grade 2H per ASTM A194/A194M
• Nut Product Marking: Manufacturer ID and 2H for forged, or 2HB if machined from
bar stock
• Finish: Light Protective Oil
• Manufacturer: Manufactured in the USA, from steel melts originating in
USA
• Material Test Reports: The MTR must have documented lot traceability, dimensional
results, full chemical test results and full mechanical test
results to the specification(s) above. In addition, the MTR
shall be in full compliance with Fastenal’s MTR
Requirements.

You might also like