HALCRO dm38 stereo power amplifier has Less than 100 parts per million mains hum and ripple on the amplifier power rails. There are 3 heavily shielded compartments: a power supply unit at full power output, all harmonic distortion orders THD -110dB (3000 parts per billion) up to 20kHz (100kHz B.W.) at 350W into 4 ohms.
HALCRO dm38 stereo power amplifier has Less than 100 parts per million mains hum and ripple on the amplifier power rails. There are 3 heavily shielded compartments: a power supply unit at full power output, all harmonic distortion orders THD -110dB (3000 parts per billion) up to 20kHz (100kHz B.W.) at 350W into 4 ohms.
HALCRO dm38 stereo power amplifier has Less than 100 parts per million mains hum and ripple on the amplifier power rails. There are 3 heavily shielded compartments: a power supply unit at full power output, all harmonic distortion orders THD -110dB (3000 parts per billion) up to 20kHz (100kHz B.W.) at 350W into 4 ohms.
Specifications and Features Specifications and features
POWER • Operates from 90 to 140V RMS, supply to minimize E.M.I. and
45-65Hz, or 200 to 240V RMS, voltage transients, which improves Power output into 4ohms resistive 45-65Hz. reliability and power efficiency > 350W • Less than 100 parts per million Power output into 8ohms resistive mains hum and ripple on the COMPARTMENTS > 180W amplifier power rails • Conforms with all current emission There are 3 heavily shielded DISTORTION (Footnote 1). and safety standards compartments: A power supply unit At full power output, all harmonic OVERLOAD (Footnote 3). An input amplifier section distortion orders A power amplifier compartment THD <-110dB (<3000 parts per Recovery from hard overload at billion) up to 20kHz (100kHz B.W.) at 20kHz into 4ohms: 1us. F I LT E R I N G 350W into 4 ohms. THD @ 1kHz <-130dB (<300 parts PROTECTION Series and common mode EMI per billion). filtering is present For sum of 19 and 20kHz tones, The amplifier protection: on the mains input each delivering 100W into 4 ohms = • Is short-circuit proof between the amplifier and power peak power 350W, intermodulation • Has over current limiting supply products each <-110dB relative to • Will cut out if temperature is High frequency filtering is present at output. excessive the inputs and output. SMPTE-IM intermodulation products • Will cut out if a continuous D.C. each <-110dB relative to output. offset appears on output DIMENSIONS • Will cut out if output current INPUTS exceeds 10A average continuously Weight: 120 lbs. or 55 kg over a period of a few minutes Height: 31 inches or 79 cm There are 3 input modes: • Is protected against most input Width: 16 inches or 40 cm • An unbalanced voltage mode input overloads Depth: 16 inches or 40 cm with an impedance of 10kohm Shipping weight: • A balanced voltage mode input The power supply protection: 187 lbs. or 85 kg with an impedance of 10kohms + • Will cut out if most common faults 10kohms are detected in the power supply FOOTNOTES • A current-mode input with a (e.g. over-voltage, master clock at 1 THD specifications of our typical 60ohm input impedance to minimize incorrect frequency, excessive best competitors are, 200,000 parts cable reflections (to be fed from an temperatures etc) per billion. infinite impedance current source) • Is protected against most mains 2 Unique to the best of our Voltage gain of the balanced and transients knowledge. unbalanced inputs is 30V/V 3 Indicates no excessive negative The gain of the current mode is COMPONENTS feedback. 5V/mA (Footnote 4). 4 “Industrial” grade is a higher grade than the “commercial” grade NOISE All semiconductors are at least used by most manufacturers. industrial grade in both the power The equivalent input noise at the supply and amplifier, for reliability input is 5nV/sqrt(Hz) for the voltage All electrolytic capacitors are modes and 6pA/sqrt(Hz) for the exceptionally long life industrial current mode. grade in both the amplifier and power supply SLEW RATE LIMIT Only highly linear resistors and the = 100V/us lowest impedance polypropylene capacitors are employed in the P O W E R S U P P LY critical audio path (Footnote 2). 6-layer PCBs are used in the power amplifier to minimize stray magnetic Active power factor correction fields and to accurately define minimizes mains current harmonic voltages distortion 4-layer PCBs are used in the power TM