You are on page 1of 4

文档名称 文档密级

Call Drop Analysis Guide

1. Relationship of different counters

CS call drop counter


VS.RAB.NormRel.AMR Normal call terminate times

VS.RAB.AbnormRel.AMR Call drop times

For call drop, below counter describe the reasons:

Main counter Sub counter


VS.RAB.AbnormRel.CS.RF.SRBReset

VS.RAB.AbnormRel.CS.RF.ULSync
VS.RAB.AbnormRel.CS.RF
VS.RAB.AbnormRel.CS.RF.UuNoReply

VS.RAB.AbnormRel.CS.OM

VS.RAB.AbnormRel.CS.Preempt

VS.RAB.AbnormRel.CS.UTRANgen
Other reason
VS.RAB.AbnormRel.CS.IuAAL2

VS.RAB.AbnormRel.CS.OLC

PS call drop counter


VS.RAB.AbnormRel.PSR99 PS R99 drop times

VS.RAB.NormRel.PSR99 Normal call terminate times

VS.RAB.AbnormRel.PS PS drop times(including R99 and HSDPA)

VS.RAB.NormRel.PS Normal call terminate times

2014-1-31 华为机密,未经许可不得扩散 第 1 页, 共 4 页
文档名称 文档密级

Main counter Sub-counter


VS.RAB.AbnormRel.PS.RF.SRBReset

VS.RAB.AbnormRel.PS.RF.ULSync
VS.RAB.AbnormRel.PS.RF
VS.RAB.AbnormRel.PS.RF.UuNoReply

VS.RAB.AbnormRel.PS.RF.TRBReset

VS.RAB.AbnormRel.PS.GTPULoss

VS.RAB.AbnormRel.PS.OM

VS.RAB.AbnormRel.PS.Preempt
Other reason
VS.RAB.AbnormRel.PS.OLC

2. Common Reason

Call drop for abnormal reasons


Failure reason Common reason
VS.RAB.AbnormRel.CS.OM Caused by some risk operation
VS.RAB.AbnormRel.CS.Preempt Check whether congestion
VS.RAB.AbnormRel.CS.UTRANgen Check alarms
VS.RAB.AbnormRel.CS.IuAAL2 Check IUCS transmission configuration and
alarm.
VS.RAB.AbnormRel.CS.OLC Check RTWP / congestions
VS.RAB.AbnormRel.PS.GTPULoss Check IUPS transmission alarms

For RF reasons:
VS.RAB.AbnormRel.CS.RF.SRBRes Check missing neighbors, alarms, coverage
et
VS.RAB.AbnormRel.CS.RF.ULSync UL limited, check RTWP, check UE TX power
VS.RAB.AbnormRel.CS.RF.UuNoRe Check missing neighbor, coverage
ply

2014-1-31 华为机密,未经许可不得扩散 第 2 页, 共 4 页
文档名称 文档密级

Optimization SOP for RF reason call drops

1. check alarms

2. Using Nastar to check missing neighbors/ pilot pollution

3. Using the Naster to check the coverage of the cells.

How to solve the call drops if the cell located in weak coverage area/network edge?

1. Identify whether RF tuning is required or not (if some area a lot sites around but still

coverage not good then RF tuning is required)

2. Modify the handover threshold/cell reselection parameters, let UE come to 2G quickly

when 3G coverage become bad.

3. If UL limited, change the CPICH power or down tilt.

MML reference for Call drop optimization:

MOD UCELLSELRESEL: CellId=13041, QualMeas=CPICH_ECNO,

QrxlevminExtSup=FALSE, IdleSintrasearch=7, SsearchRat=4,

NonhcsInd=NOT_CONFIGURED;

UE will do intra-cell reselection when 3G EcIo is below -4dB, will do inter-RAT cell

reselection when 3G EcIo is below -10dB.

ADD UCELLINTERRATHOCOV: CellId=13041,

InterRatReportMode=PERIODICAL_REPORTING, InterRATCSThd2DEcN0=-10,

InterRATCSThd2FEcN0=-8, InterRATCSThd2DRSCP=-95, InterRATCSThd2FRSCP=-92;

UE will start compress mode when 3G EcIo is below -10 or RSCP is below -92.

MOD UPCPICHPWR: CellId=13451, MaxPCPICHPower=370, MinPCPICHPower=320;

MOD UCELL: CellId=13451, PCPICHPower=340;

Change the Cell CPICH power from 36dBm to 34dBm.

2014-1-31 华为机密,未经许可不得扩散 第 3 页, 共 4 页
文档名称 文档密级

2014-1-31 华为机密,未经许可不得扩散 第 4 页, 共 4 页

You might also like