Professional Documents
Culture Documents
(
http://www.erdc.usace.army.mil/Library.aspx)
Show simple item record (/xmlui/handle/11681/19038)
dc.date.accessioned 2016-10-03T18:54:29Z
dc.date.available 2016-10-03T18:54:29Z
dc.date.issued 1956
dc.identifier 3-441
dc.identifier 4557308
dc.identifier 2439
dc.identifier http://cdm16021.contentdm.oclc.org/cdm/ref/collection/p266001coll1/id/2439
dc.identifier.uri http://hdl.handle.net/11681/19038
https://erdc-library.erdc.dren.mil/xmlui/handle/11681/19038?show=full 1/5
5/17/2018 Mathematical expression of the CBR relations
empirical tool used to evaluate materials in flexible pavement systems. The CBR
values are considered to be indica-tive of the resistance of subgrade and base course
materials to the stresses that may be imposed upon them by repetitive wheel loads.
The design curves used with the CBR method express relationships between loads,
protective thickness of superior material, and CBR of the pertinent layer in the flexible
pavement system. 2. Theoretical shear-stress relationships, allowable deformations,
and relationships between relative sizes of loaded areas were used to ex-trapolate the
basic California Highway Department curves to airplane loadings. Subsequently,
theoretical relationships such as shear stresses, vertical stresses, and vertical
deflections have been used to study the pattern of the CBR design curves. Graphical
relationships have also been used. These studies and service behavior records show
that the CBR de-sign curves can be divided into two parts. At the greater depths
beneath the surface of flexible pavements, required strengths are governed pri-marily
by the gross magnitudes of applied loads. These greater depths are the zone in which
the smaller CBR values are usually encountered. At the lesser depths beneath the
pavement surface, on the other hand, the intensity of applied loads is the primary
governing factor in the deter-mination of required strengths. These lesser depths are
the zone in which the larger CBR values are usually encountered. 3. The
developments presented in this report are concerned with the small CBR range
(greater depths) for which they establish a firm mathematical pattern interrelating the
various pertinent factors. Mathematical Developments 4. Prior work has already
established a relation between design thickness, wheel load, and a constant
dependent on the CBR for single 2 wheel loads having the same contact pressure
(tire pressure).1, 4* This relation is expressed as follows: t = K (1) where: t = thickness
P = wheel load K = a constant dependent on the CBR. The formula is arrived at in the
following manner: Relations obtained from the theory of elasticity for homogeneous-
isotropic material under a uniformly loaded circular area show that for a given intensity
of sur-face load the stresses beneath total loads of different magnitudes will be equal
at homologous points. Homologous points are points beneath two loads of the same
intensity for which the ratio of the depth to the radius of the load is a constant. It is
reasonable to assume that the needed strength and therefore the required CBR will
be the same at depths at which the stresses are identical. Therefore, it may be as-
sumed that for a given CBR and intensity of load, the depth of cover or thickness of
protective layer for any magnitude of load must be such that the ratio of the thickness,
t , to the radius of contact area, r , is a constant, C , or = . (2) r The relation between
load, P , load intensity, p , and radius of con-tact area, r , is: P=pnr2 or r =V x - . (3)
Combining equations 2 and 3 gives: * Raised numbers refer to the list of references at
the end of the text. C X VT.(4) Now being a constant can be designated as K . Thus, K
is a constant dependent on the CBR for a given intensity of pressure. Sub-stituting K
for results in equation 1. t = K . (1) This is the expression presented in earlier work.11
Use of this rela-tion permits the development of increasingly larger wheel load CBR
curves from existing CBR curves. The relation has been shown to give values in good
agreement with those determined by service behavior and empirical tests for CBR
values below about 15 to 20. In the initial development of the CBR relations, tire
pressure was not considered. However, tire pressures used originally in developing
service behavior records for airplane loadings ranged from 60 to slightly above 100
psi. Therefore, when preparation of design curves for 200-psi tires became necessary
the established relationships were assumed to be valid for tire pres-sures up to 100
psi. The simple relation for equal stress at homologous points applies only for a single
https://erdc-library.erdc.dren.mil/xmlui/handle/11681/19038?show=full 2/5
5/17/2018 Mathematical expression of the CBR relations
intensity of applied load and would not serve for extrapolating the design curves from
100- to 200-psi tire pressures, but it was found that the relations of the theory of elas-
ticity for deflection beneath the center of a uniform circular load could be used.1 The
pertinent relation is: 2 w = 1.5 E x r (5) m Yr 2 +t 2 r + t where: w = deflection E =
modulus of elasticity m p, r, and t are the same as in equations 2 and 3. By
considering that an increase in tire pressure would require an in-crease in protective
thickness (depth) such that the theoretical de-flections would be equal, CBR relations
were developed for higher tire pressures. These have since been validated by field
test results.3 5. Equation 5 can be combined with equation 3 to give the following: P 1
2 2 W = 1.5- 1.5 x p x or r + t= (6) xE wnE m 2 2m For a given situation E can be
considered to have a single value, and m if the total load is considered to be constant
and tire pressure per-mitted to vary, the right-hand side of equation 6 is constant when
the deflection is constant and the following expression can be written: r2 +2 =C' (7)
where r and t are as defined previously and C' is a constant. 6. It is now possible to
examine the effect on thickness require-ments of changes in gross load and of
changes in tire pressure. First, consider a change in gross load from Pa to Pb. at
equal tire pres-sure. From equation 1, the following can be written: ta = K =tb or tb- =
b where pa = b (8) a ( a a Now consider a change in tire pressure from pb to pc with
no change in gross load (P = Pc ) . From equation 7, the following can be written: r +
=+Ct' =rc +tc oorr t+t r = tb + b - re wwhheerree Pb == PP . ((99)) Squaring equations
8 and 9 and combining gives: 2 2 b 2 2 tc =t + rb rc (10) This can be developed in the
following manner to give an expression for the combined effect of variations in total
load and tire pressure: 2 2 2 2 Pb xpb rb c re t =t + c a Pb a P P 5 but, npr2 = P,
therefore: 2 2 b Pb Pc t =t +--- - --- c a a spb spc and since, pa -=b and Pb P c P P 2 2
c c 1 1 c a P- p p Sa P This may be written: tc + Pc Pa1 Pc1 (11) a2 It may also be
written: t 2 2 a +--- 1 = c + ---1- . P n Pc Pc a a C c Since the subscripts represent
arbitrary sets of values, the following more general expression can be written: 2 t 2 t 2
2 a 1 c 1 e 1 n 1 -+ - = + = .... - + - a a c c e e n n Or, since any set of values
combined in this way must equal any other set so combined, it follows that the
expression must equal a constant: -t-2 + 1 = D ,where D is a constant . (12) P pit 7.
This expression is similar to equation 1 except that it will accommodate variations in
tire pressure as well as in gross load. The similarity of equations 1 and 12 is readily
apparent, and their combina-tion provides a relation between the constants D and K .
This relation is: D = K + -p-1n (13) 6 Reference to paragraph 4 will show that K can be
considered to have the in. in. 2 units --- and therefore D will have the units in. . Since
K is dependent on the CBR, it follows that D is also dependent on CBR. 8. Values for
the constant K were carefully developed as shown in reference 4. The values
developed in that reference and in reference 1 are shown in the following table. These
are from single-wheel CBR curves for design (or evaluation) of flexible airfield
pavements for capacity operation (5000 coverages). In evaluation of the constant K ,
units must be assigned to the various quantities, therefore t has been taken in inches,
P in pounds, and K in pounds per square inch. Values of K For 100-p For 200-psi R
curves CER curves 0.195 0.199 0.166 0.171 0.147 0.152 0.132 0.138 0.120 0.126
0.111 0.118 0.103 0.110 0.096 0o. 104 0.085 0.093 0.073 0.082 0.067 0.075 0.059
0.068 Values of K2 For 100-psi For 200-psi CER curves CR curves 0.03803 0.03961
0.02755 0.02923 0.02161 0.02311 0.01742 0.01905 0.01440o 0.01588 0.01232
0.01392 0.01060 0.01210 0.00921 0.01o81 0.00723 0.00865 0.00533 0.00672
0.00oo49 0.00563 0.00348 0.00oo462 Values of D = + For 100-psi For 200-psai CBR
curves CBR curves 0.04121 0.04120 0.03073 0.03082 0.02479 0.02470 0.02060
https://erdc-library.erdc.dren.mil/xmlui/handle/11681/19038?show=full 3/5
5/17/2018 Mathematical expression of the CBR relations
dc.format pdf
dc.language eng
dc.rights This document was published by a federal government agency and is in the public
domain.
dc.source 0558MATH.pdf
https://erdc-library.erdc.dren.mil/xmlui/handle/11681/19038?show=full 4/5
5/17/2018 Mathematical expression of the CBR relations
https://erdc-library.erdc.dren.mil/xmlui/handle/11681/19038?show=full 5/5