Professional Documents
Culture Documents
There are many ways of modeling bolted connections using ANSYS workbench FE software. This article provides an
overview of various methods including best practices. Here is my list in order of increasing complexity and modeling
fidelity:
This is the simplest connection. Bolts and nuts are removed from the assembly. A bonded connection is created around the
bolt hole as shown. The bonded region can be taken as having a diameter equal to the washer used as shown in the figure.
The bonded region simulates friction grip of the joint around the bolted connection.
1
Bonded Connection
This type of connection is ideally used in the global analysis of large assemblies where modeling of bolts will become
computationally intensive. A key assumption here is that the bolted joint maintains its friction grip and does not slip. A
subsequent sub-modeling analysis of this bolted connection with 3D solid bolts will reveal its true integrity i.e., whether it
slips or not. The bonded connection enables linear analysis which is much faster than a non-linear contact.
2) Beam Bolts:
The way to create Beam bolts is to import the CAD file into design modeler and use bolt and nut head boundary edge to
create imprints on the plate surfaces in contact with the bolt and nut (see image below). If a washer is used, then use the
washer boundary edge for imprinting. Next, suppress the solid bolt and nut and open up the model in mechanical application
where beam connections are made via Body-Body -> Beam connection. For reference and mobile surfaces use the hexagonal
or circular imprints created in design modeler.
Beam Bolts. The red lines represent constraint equations that connect the beam element to bolted faces (hexagonal imprints)
2
The beam connection creates constraint equations between beam nodes and reference and mobile surfaces. The behavior can
be set to rigid or deformable, although none of these options can capture the true stiffness of bolt head and nut. The bolt
pretension can be computed using the following formula
Where:
In recent versions of ANSYS bolt pretension can be applied on beam bolts. In earlier versions APDL commands can be
used. The contact between the mating plates is
3) Spring Bolts
The third type of bolted connection is a spring bolt. It is applied in a similar manner to beams. A pretension or pre-load value
is defined in the details of spring joint. In addition, spring stiffness “Ks’ is computed based on bolt shank geometry: Ks = E
At/Ls. Where E is the young’s modulus, ‘At’ is the tensile bolt shank area and Ls is the shank length equal to the combined
thickness of the mating plates.
Spring Bolt
3
4) 3D Solid Bolts
This is the highest fidelity bolted connection model so far. This model enables us to capture the bolt and nut stiffness as well
as post slip effect when the shank comes into contact with bolt hole. The downside is significant computational cost, in
particular, if there are several bolts in a big assembly. Therefore, this analysis is best suited to sub-modeling. The key steps
in modeling solid bolts are shown below:
The bolt shank diameter should be based on ‘At’, the tensile area. This change should be made in CAD when converting the
bolt for FEA analysis. It is also a good practice to remove any features such as chamfers, fillets or protrusions in the bolt or
nut body in CAD in order to obtain a nice mesh.
After the bolt is imported into ANSYS Design modeler, the bolt shank surface should be split as shown via projection
method using the nut face edge. The splitting of the shank at the nut face is very important since pretension load in
mechanical will split the shank body in half and pull it together to impose the pretension load. The selected pretension
surface should be separate from any bonded contacts such as nut-to-shank bonded contact, otherwise it may cause problems
when pretension is applied. The bolt should be hex meshed using the multi-zone method. There should be a frictional contact
between mating plate faces. The contacts between bolt head-to-plate and nut-to-plate can be either frictional or if bonded.
Frictional contact is more realistic but is also computationally intensive. In case of post slip failure of bolt needs to be
analyzed, a frictional contact should be created between the bolt shank and plate holes. See details of contacts below.
4
Solid bolt contacts
Simulation Results
5
Post Processing Bolted Connection Results
Post processing involves getting key results out of our analysis that we can use for making critical decisions. As far as the
bolted connection is concerned, we can look at peak stress, contact slippage as well as total axial load on the shank. The last
one is used for analysis of threads. For the beam bolts, finding axial load is straight forward using beam probe. This gives us
axial load, moment and shear forces at nodes I & J. For the 3D solid bolt, we need to create a construction surface cutting the
shank. This surface should not be located at least one or two elements away from the pretension split region otherwise we
will get erroneous results. The split region is easy to identify by looking at total deformation as shown below.
Now in order to find the total force, we select force reaction probe > Location Method = Surface > then select the
construction surface created above. This will give us the resultant force as shown above. Here is a brief comparison of bolted
connection models. The contact behavior can also be displayed using the “contact tool”. Notice the sticking region has
shrunk slightly after the application of full load. This shrinking implies local slippage of plates. If the sticking region
vanishes, we consider that a failure of the friction-grip type bolted connection. The figure below shows contact status of
solid bolt. The contact results for beam bolts are very similar if not identical.
6
Conclusion
A summary table of key results is shown. Note that the spring based bolted connection is identical to the beam bolt so its
results are presented in this table.
These results show that the bonded contact model solves in a fraction of time compared to beam and 3D solid bolts. The
difference is largely due to linear analysis in the case of bonded connection. The simulation time looks comparable for beam
and solid bolts. However, in a sub-model comprising of many bolts, this difference will become significant. Beam bolts can
also be used in global analysis, in particular, if the problem size is not very large. The downside is that a non-linear analysis
will have to be performed due to frictional contact between the plates. Solid bolts should always be used in sub-models of
critical joints in a big assembly.
Related Articles
Finite Element Models of Varying Fidelity
Models of various fidelity can be used for analyzing structures or any physical system. The decision is made based on
desired results as well as computational resources available. In this...
ANSYS and SolidWorks: Creating a Two Way Link
In this article I will show how ANSYS Workbench and solidworks CAD softwares can be linked so that when a parameter is
changed in one, it is automatically updated in...
Validating FEA Results
The purpose of this article is to post-process and understand FEA results by comparing with standard text book theory and
hand calculations. I will use the example of a cantilever I-beam...