You are on page 1of 28

SYLLABUS OF SEMESTER SYSTEM

FOR THE TRADE OF

Mechanic Auto Electrical &


Electronics

Under

Craftsmen Training Scheme (CTS)


(One year/Two Semesters)

Redesigned in
2014

By
Government of India
Ministry of Labour & Employment (DGE&T)
GENERAL INFORMATION

1. Name of the Trade : Mechanic Auto Electrical & Electronics

2. N.C.O. Code No : 7241.70, 7242.10, ASC/ Q 1408

3. Duration of Craftsmen Training : 1Year (Two Semester having duration of six


months each)

4. Power Norms : 3 KW

5. Space Norms : Space Area 100 Sq. Mt. (Including parking area)

6. Entry Qualification : Passed 10th class examination with maths and


Science

7. Unit strength : 16 + 30% super Numeric

8. Instructors Qualification : a) Degree in Automobile/ Mechanical Engg./


Electrical /Electronics & communication Engg
Engineering (with specialization in
Automobile) from recognised college/
University with one year experience in the
automobile industry and should possess valid
LMV driving license
OR
Diploma in Automobile/Mechanical
(specialization in automobile) / Electrical
Engineering / Electronics & communication
Engg from recognized board of technical
education with two years experience in the
automobile industry and should posses valid
LMV driving license.

OR
10th Passed + NTC/NAC in the Trade of
“Mechanic Auto Electrical & Electronics”
with 3 years post qualification experience in
the relevant field, and should posses valid
LMV driving license.
and
b) With “National Crafts Instructor
Certificate”.

* Note: 1) At least one Instructor must have Degree/Diploma in Automobile/ Mechanical


Engg/ Electrical Engineering / Electronics & communication. when applied for 02
units.
2) Instructor Qualification for WCS & E.D, as per the Training Manual.
9. For Employability Skills One Contract/Part Time/Guest Faculty for Generic Module .
i) MBA/ BBA with two years experience OR Graduate in Sociology / Social Welfare /
Economics with Two years experience OR Graduate / Diploma with Two years
experience and trained in Employability Skills from DGET institutes
AND
Must have studied English / Communication Skills and Basic Computer at 12th / Diploma
level and above
OR
Existing Social Study Instructors duly trained in Employability Skills from DGET
institutes

Distribution of training on Hourly basis:

Total hours Trade Trade Work Engg. Employability Extra


/week practical theory shop Cal. Drawing skills curricular
&Sc. activity
42 Hours 27 Hours 5 Hours 3 Hours 3 Hours 2 Hours 2 Hours

COURSE INFORMATION (MECHANIC AUTO ELECTRICAL AND ELECTRONICS)


1.Introduction :
 An intensive industrial survey was made to ascertain the requirements of skill-
gap in the automobile sector, a scientifically designed survey covering labour-
market survey web-survey was conducted. Based on the data obtained the skills
are identified and accordingly the syllabus has been drafted. Subsequently the
Trade expert committed reviewed.

2. Terminal Competencies/Deliverables :

After successful completion of the above course, the trainee shall be able to perform the
following skills with proper sequence.

 Installs, repairs replaces and overhauls wiring, starters, generators, distributors and other
electrical equipment of motor vehicles.

 Examines vehicle battery, checks voltage and specific gravity using special equipment such
as voltmeter hydrometer, heavy discharge tester, etc. and ensures that battery is in good
condition.

 Checks vehicle wiring, locates faults and rectifies defects by replacing damaged wire or
connecting ends with insulation tape.

 Starts engine to check whether alternator is charging correctly, and if distributor, condenser
coil and cut out are functioning properly.

 Estimates nature of defects and reports components to be replaced or repaired.

 Dismantles and repairs electrical units and components such s generator, distributor etc.
where required.

3
3
 Replaces repaired kit or unit in vehicle and connects it with battery.

 Conducts thorough examination of various electrical fittings such as lights, panel indicators,
fuel pumps, etc and rectifies defects.

 Checks condition and makes necessary adjustments. May do armature winding. May drive
vehicles on road. May charge batteries.

 Fits, assembles and repairs various kinds of electronic equipment in factory or workshop or at
place of use.

 Examines drawings and wiring diagrams; checks parts for accuracy of fit and minor
adjustments; assembles parts or mounts them on chassis or panels with aid of hand tools;
Installs and connects wiring, soldering joints equipment, diagnoses faults with aid of
electronic testing equipment;

 Dismantles equipment if required and replaces faulty parts or wiring.

3. Employment opportunities:
On successful completion of the course the candidates can either get employed, or become a
self-employed Entrepreneur in any one of the following fields.

a) Wage Employment b) Self Employment


1. Auto Electrician 1. Diagnostic Mechanic
2. Spare Parts Sales Assistant / Manufacturers' 2. Spare Parts Salesman
Representative 3. Spare Parts Dealer
3. Laboratory Assistant
4. Diagnostic Mechanic
5. Car AC Mechanic

4. Further learning pathways:

 On successful completion of the course trainee can get themselves enrolled in


Apprenticeship training in reputed Industrial organisation.
 The qualified candidates have scope for lateral entry into the Diploma courses offered by
some of the State Governments
 The qualified candidates can also get themselves upgraded by taking up the Second
Semester at his own convenience in the CTS scheme , since the first semester is common to
the following trades.

Craftsman Training Scheme


1. Mechanic Motor Vehicle - 2 Years ( 4 Sem)
2. Mechanic Diesel – 1 Year ( 2 Sem)
3. Mechanic Motor Cycle - 1 Year ( 2 Sem)
4. Mechanic Auto Electrical and Electronics - 1 Year ( 2 Sem)
5. Mechanic Agricultural Machinery - 2 Years ( 4 Sem)
6. Mechanic Tractor - 1 Year ( 2 Sem)
7. Pump Operator cum Mechanic - 1 Year ( 2 Sem)

4
4
Syllabus for the trade of Mechanic Auto Electrical & Electronics
First Semester (Semester code No. )
Duration: Six Months.
Syllabus for Trade practical and Trade Theory
Week Trade Practical (27 Hrs/week) Trade Theory (5 Hrs/week)
No.
1 Familiarisation with institute, Job Admission & introduction to the trade:
opportunities in the automobile Introduction to the Course duration, course
sector, Machinery used in Trade. content, study of the syllabus. General rule
Types of work done by the students pertaining to the Institute, facilities available–
in the shop floor. Hostel, Recreation, Medical and Library working
hours and time table
2 Practical related to Safety and Occupational Safety & Health
Health, Importance of Safety and general
Importance of maintenance and Precautions to be observed in the shop. Basic
cleanliness of Workshop. first aid, safety signs - for Danger, Warning,
Interaction with health centre and caution & personal safety message. Safe handling
fire service station to provide demo of Fuel Spillage, Fire extinguishers used for
on First aid and Fire safety, Use of different types of fire. Safe disposal of toxic dust,
fire extinguishers. safe handling and Periodic testing of lifting
Demonstration on safe handling and equipment, Authorization of Moving & road
Periodic testing of lifting equipment, testing vehicles.
and Safety disposal of Used engine Energy conservation-Definition, Energy
oil. Conservation Opportunities (ECOs)-Minor ECos
Energy saving Tips of ITI electricity and Medium ECOs, Major ECOs), Safety disposal
Usage of Used engine oil, Electrical safety tips.
3-5 Practice using all marking aids, like Hand & Power Tools:-
steel rule with spring calipers, Marking scheme, Marking material-chalk,
dividers, scriber, punches, Chisel Prussian blue. Cleaning tools- Scraper, wire
etc., brush, Emery paper, Description, care and use of
Layout a work piece- for line, circle, Surface plates, steel rule, measuring tape, try
arcs and circles. square. Calipers-inside and outside. Dividers,
Practice to measure a wheel base of a surface gauges, scriber, punches-prick punch,
vehicle with measuring tape. center punch, pin punch, hollow punch, number
Practice to measure valve spring and letter punch. Chisel-flat, cross-cut. Hammer-
tension using spring tension tester ball pein, lump, mallet. Screw drivers-blade
Practice to remove wheel lug nuts screwdriver, Phillips screw driver, Ratchet
with use of an air impact wrench screwdriver. Allen key, bench vice & C-clamps,
Practice on General workshop tools Spanners- ring spanner, open end spanner & the
& power tools. combination spanner, universal adjustable open
end spanner. Sockets & accessories, Pliers -
Combination pliers, multi grip, long nose,
flat-nose, Nippers or pincer pliers, Side cutters,
Tin snips, Circlip pliers, external circlips
pliers. Air impact wrench, air ratchet, wrenches-
Torque wrenches, pipe wrenches, car jet washers
Pipe flaring & cutting tool, pullers-Gear and
bearing.

5
5
6&7 Measuring practice on Cam height, Systems of measurement, Description, care &
Camshaft Journal dia, crankshaft use of - Micrometers- Outside and depth
journal dia, Valve stem dia, piston mirometer, Micrometer adjustments, Vernier
diameter, and piston pin dia with calipers, Telescope gauges, Dial bore gauges, Dial
outside Micrometers. indicators, straightedge, feeler gauge, thread pitch
Measuring practice on the height of gauge, vacuum gauge, tire pressure gauge.
the rotor of an oil pump from the
surface of the housing or any other
auto component measurement with
depth micrometer.
Measuring practice on valve spring
free length.
Measuring practice on cylinder bore,
Connecting rod bore, inside diameter
(ID) of a camshaft bearing with
Telescope gauges.
Measuring practice on cylinder bore
for taper and out-of-round with Dial
bore gauges.
Measuring practice to measure wear
on crankshaft end play, crankshaft
run out, and valve guide with dial
indicator.
Measuring practice to check the
flatness of the cylinder head is
warped or twisted with straightedge
is used with a feeler gauge.
Measuring practice to check the end
gap of a piston ring, piston-to-
cylinder wall clearance with feeler
gauge.
Practice to check engine manifold
vacuum with vacuum gauge.
Practice to check the air pressure
inside the vehicle tires is maintained
at the recommended setting.
8&9 Practice on General cleaning, Fasteners- Study of different types of screws,
checking and use of nut, bolts, & nuts, studs & bolts, locking devices, Such as lock
studs etc., nuts, cotter, split pins, keys, circlips, lock rings,
lock washers and locating where they are used.
Removal of stud/bolt from blind Washers & chemical compounds can be used to
hole. help secure these fasteners. Function of Gaskets,
Selection of materials for gaskets and packing, oil
Practice on cutting tools like seals.
Hacksaw, file, chisel, Sharpening of Cutting tools :- Study of different type of cutting
Chisels, center punch, safety tools like Hacksaw, File- Definition, parts of a
precautions while grinding. file, specification, Grade, shape, different type of
cut and uses., OFF-hand grinding with sander,
Practice on Hacksawing and filing to bench and pedestal grinders, safety precautions
given dimensions. while grinding.
Limits, Fits & Tolerances:-Definition of limits,

6
6
fits & tolerances with examples used in auto
components
10 & Practice on Marking and Drilling Drilling machine - Description and study of
11 clear and Blind Holes, Sharpening of Bench type Drilling machine, Portable electrical
Twist Drills Safety precautions to be Drilling machine, drill holding devices, Work
observed while using a drilling Holding devices, Drill bits.
machine. Practice on Tapping a Taps and Dies: Hand Taps and wrenches,
Clear and Blind Hole, Selection of Calculation of Tap drill sizes for metric and inch
tape drill Size, use of Lubrication, taps. Different type of Die and Die stock. Screw
Use of stud extractor. extractors. Hand Reamers – Different Type of
Cutting Threads on a Bolt/ Stud. hand reamers, Drill size for reaming, Lapping,
Adjustment of two piece Die, Lapping abrasives, type of Laps.
Reaming a hole/ Bush to suit the
given pin/ shaft, scraping a given
machined surface.
12 Practice on making Rectangular Sheet metal - State the various common metal
Tray. Sheets used in Sheet Metal shop
Pipe bending, Fitting nipples unions Sheet metal operations - Shearing, bending,
in pipes. Soldering and Brazing of Drawing, Squeezing
Pipes. Sheet metal joints - Hem & Seam Joints Fastening
Methods - Riveting, soldering, Brazing. fluxes
used on common joints. Sheet and wire-gauges.
The blow lamp- its uses and pipe fittings.
13 Practice in joining wires using Basic electricity, Electricity principles, Ground
soldering Iron, Construction of connections, Ohm's law, Voltage, Current,
simple electrical circuits, Measuring Resistance, Power, Energy. Voltmeter, ammeter,
of current, voltage and resistance Ohmmeter Mulitmeter, Conductors & insulators,
using digital multimeter, practice Wires, Shielding, Length vs. resistance, Resistor
continuity test for fuses, jumper ratings
wires, fusible links, circuit breakers.
14 Diagnose series, parallel, series- Fuses & circuit breakers, Ballast resistor,
parallel circuits using Ohm’s law, Stripping wire insulation, cable colour codes and
Check electrical circuit with a test sizes, Resistors in Series circuits , Parallel
lamp, perform voltage drop test in circuits and Series-parallel circuits, Electrostatic
circuits using multimeter, measure effects, Capacitors and its applications, Capacitors
current flow using multimeter in series and parallel.
/ammeter, use of service manual
wiring diagram for troubleshooting.
15 Cleaning and topping up of a lead Description of Chemical effects, Batteries &
acid cells, Lead acid batteries & Stay Maintenance
battery, Testing battery with Free (SMF) batteries, Magnetic effects, Heating
hydrometer, effects, Thermo-electric energy, Thermisters,
Connecting battery to a charger for Thermo couples, Electrochemical energy, Photo-
battery charging, Inspecting & testing a voltaic energy, Piezo-electric energy,
battery after charging, Measure Electromagnetic induction, Relays, Solenoids,
and Diagnose the cause(s) of Primary & Secondary windings, Transformers,
excessive Key-off battery drain stator and rotor coils.
(parasitic draw) and do corrective
action. Testing of relay and solenoids
and its circuit.

7
7
16 Identify and test power and signal Basic electronics: Description of Semi
connectors for continuity, Identify conductors, Solid state devices- Diodes,
and test different type of Diodes, NPN & Transistors, Thyristors, Uni Junction Transistors
PNP Transistors for its functionality, ( UJT), Metal Oxide Field Effect Transistors
Construct and test simple logic ( MOSFETs), Logic gates-OR, AND & NOT and
circuits OR, AND & NOT and Logic Logic gates using switches.
gates using switches.
17& Practice to make straight beads and
Introduction to welding and Heat Treatment
18 Butt, Lap & T joints Manual Metal
Arc Welding. Welding processes – Principles of Arc welding,
brief description, classification and applications.
Setting of Gas welding flames, Manual Metal Arc welding -principles, power
practice to make a straight beads and sources, electrodes, welding parameters, edge
joints Oxy – Acetylene welding
preparation & fit up and welding techniques; Oxy
Film on Heat treatment process – Acetylene welding - principles, equipment,
welding parameters, edge preparation & fit up and
welding techniques;.
Heat Treatment Process– Introduction, Definition
of heat treatment, Definition of Annealing,
Normalizing, Hardening and tempering. Case
hardening, Nitriding, Induction hardening and
Flame Hardening process used in auto
components with examples.
19 & Practice on Liquid penetrant testing Non-destructive Testing Methods- Importance
20 method and Magnetic particle testing of Non-Destructive Testing In Automotive
method. Industry, Definition of NDT, Liquid penetrant
Identification of Hydraulic and and Magnetic particle testing method – Portable
pneumatic components used in Yoke method
vehicle. Introduction to Hydraulics & Pneumatics: -
Tracing of hydraulic circuit on Definition of Pascal law, pressure, Force,
hydraulic jack, hydraulic power viscosity. Description, symbols and application in
steering, and Brake circuit. automobile of Gear pump-Internal & External,
Identification of components in Air single acting, double acting & Double ended
brake systems. cylinder; Directional control valves-2/2, 3/2, 4/2,
4/3 way valve, Pressure relief valve, Non return
valve, Flow control valve used in automobile.
Pneumatic Symbols, Description and function of
air Reciprocating Compressor. Function of Air
service unit (FRL-Filter, Regulator & Lubricator).
21 Identification of different type of Auto Industry - History, leading manufacturers,
Vehicle. development in automobile industry, trends, new
Demonstration of vehicle product. Brief about Ministry of Road transport &
specification data; Highways,
Identification of vehicle information The Automotive Research Association of India
Number (VIN). Demonstration of (ARAI), National Automotive Testing and R&D
Garage, Service station equipments.- Infrastructure Project (NATRIP), & Automobile
Vehicle hoists – Two post and four Association.
post hoist, Engine hoists, Jacks, Stands. Definition: - Classification of vehicles on the
basis of load as per central motor vehicle rule,
wheels, final drive, and fuel used, axles, position
of engine and steering transmission, body and

8
8
load. Brief description and uses of Vehicle hoists
– Two post and four post hoist, Engine hoists, Jacks,
Stands.
22-23 In-plant Training
24-25 Revision and Test
26 NCVT Exam

9
9
Automobile Group – 1 year Trade
1st Semster
Workshop Calculation and Science
Syllabus for the trade of Mechanic Auto Electrical & Electronics

Week Workshop calculation and


No. Science (3 Hrs/week)
1 Units, Derived and fundamental, types of system FPS, CGS, MKS and their conversion.
Metric weights and measurements, units conversion factors
2 Fractions- Addition and subtraction, Fractions and whole numbers, Combined addition
and subtraction, Multiplication and division of fractions. Operations in problems involving
fractions.
3 Order of performing (BODMAS) Mathematical operators , Integers – Rules for dealing
with integers, Addition, subtraction, Multiplication and division.
4&5 Ratio and proportion. Percentages, Examples of ratios in Automotive technology
6 profit and loss, Discount .
.
7 simple interest and compound interest
8 depreciation calculation
9-10 Time and work problem , Time and distance, clocks and calendar,
11 Brief description of manufacturing process of steel, and aluminum
12 Meaning of elasticity, malleability, brittleness, hardness, compressibility & ductility and
their examples , Properties and uses of cast iron, ferrous metal, gray cast iron, white cast
iron, wrought iron, and plain carbon steel, high speed steel and alloy steel.
13 Properties and uses in automobile industries- copper, zinc, lead, tin, aluminum, brass,
bronze, solder bearing metals, timber and rubber. Nylon, P.V.C., PP (poly prop line,
polymer).
14-15 Materials – Stress, strain,- Definition of Stress, Types of stress- Tensile, compressive,
shear , Examples of the three basic stresses in automotive components , calculation of stress
and strain in automotive application, Stress raisers, Strain-, Tensile, compressive, Shear
strain, Tensile strength, Factor of safety, Torsional stress, Strain energy.
16 Definition of cold working and Hot working and its properties on sheet metal. Advantage of
Deep drawing material. Importance of Iron- carbon diagram in heat treatment process.
17 Different Type of cutting fluids and their properties. Calculation of cutting speed, feed and
drilling time.
18-19 Forces – Definition of Force, Types of force -examples,– Direct forces, Attractive forces,
Explosive forces, Describing forces, Graphical representation of a force, Addition of
forces, Parallelogram of forces ,Triangle of forces, Resolution of forces, Mass,
Equilibrium, Pressure, Pressure in hydraulic systems, Hooke’s law, Practical applications.
20-21 Work energy, power– Definition and calculation of Work, Power and Work done by a
torque, Definition and calculation of Energy -Potential energy, Chemical energy,
Conservation of energy, Energy equation, Kinetic energy, Energy of a falling body, Kinetic
energy of rotation.

10
10
Automobile Group – 1 year Trade
1st Semster- Engineering Drawing
Syllabus for the trade of Mechanic Auto Electrical & Electronics

Week Engineering Drawing (3 Hrs/week)


No. 1st Semester
1 Importance of engineering drawing as a communication medium, different types of drawing
- Machine Drawing, Production Drawing, Part Drawing, Assembly Drawing, Drawing
instruments, equipment and materials and their uses
2&3 Scales - Recommended scales, reduced & enlarged Drawing Sheet sizes: A0, A1, A2, A3,
A4, A5, Layout of drawing sheet, sizes of title block and its contents. Using drawing
instruments to draw straight lines, rectangles, squares, circles, polygons.
4&5 Lettering and Dimensioning - Types of Lettering, Guide Lines for lettering, Recommended
sizes of letters and numbers, Single stroke letters, Dimensioning - rules and systems of
dimensioning – dimensioning a given drawing.
6&7 Identify the alphabet of lines- Read and Interpret the meaning of various line types with
examples- Object Lines, Hidden Lines, Center Lines, Phantom Lines, Dimension Lines,
Extension Lines, Leaders, Break Lines -Long-break Line, Round, Solid, Hollow Cross
Section, Section Lines – Common Manufacturing Materials, Cutting Plane Lines
8-11 Geometric Construction - Bisecting a line - perpendiculars - parallel lines - division of a
line; Angles - bisection, trisection, Tangent lines touching circles internally and externally
Polygons - Regular polygons - circumscribed and inscribed in circles. Conic sections -
Definitions of focus, directrix, eccentricity, Construction of Ellipse by Concentric circles
method, Construction of parabola by rectangular method.
12&13 Orthographic Projection - Definition - Planes of Projection - Four quadrants – Reference
Line, First angle projection - Third angle projection.
14-17 Isometric Projection - Definition - Isometric axes, lines and planes, Isometric Scale -
Isometric view. Drawing of isometric views of plane figures, Drawing of isometric views of
prisms and pyramids, Drawing of isometric view of cylinders and cones
18-21 Development of Surfaces - Need for preparing development of surface, Concept of true
length - Principal methods of development, Development of simple solids like cubes,
prisms, cylinders, pyramids, cones.

YLLABUS FOR EMPLOYABILITY SKILLS


SEMESTER-I
(pl ref to www.dget.nic.in)

11
11
Syllabus for the trade of Mechanic Auto Electrical & Electronics
Second Semester (Semester code No. )
Duration: Six Months.
Syllabus for Trade practical and Trade Theory

Week Trade Practical (27 Hrs/week) Trade Theory (5 Hrs/week)


No
1 Identification of parts in a diesel engine Introduction to Engine:
of LMV/ HMV Principle & working of 4-stroke diesel engine
Practice on starting and stopping of (Compression ignition Engine (C.I)), Principle
diesel engines. of Spark Ignition Engine(SI), difference
Observe and report the reading of between C.I engine and S.I Engine, Technical
Tachometer, Odometer, temp and Fuel terms used in engine, Engine specification.
gauge under ideal and on load Study of various gauges/instrument on a dash
condition. board of a vehicle- Speedometer, Tachometer,
. Odometer and Fuel gauge, and Indicators such
as gearshift position, Seat belt warning light,
Parking-brake-engagement warning light and
an Engine-malfunction light.
Different type of starting and stopping method
of Petrol/Diesel Engine
2 Practice to identify components and Electrical and Electronic Components:-
their locations indicated on the wiring Switches- Description of Normally open,
diagram. Normally closed, single pole single throw
switch (SPST), ganged, and mercury switches
Practice to identify the power source, used in Automobile circuit.
ground connection, and controls for Description of Relay, ISO Relays, Solenoids,
electrical circuits using a wiring Buzzers.
diagram. Resistors- Description of different type of
resistors and their colour codes.- Fixed,
stepped, and variable resistors-Rheostat,
Potentiometer.
Description of Diodes, Diode identification and
ratings, zener diodes, Avalanche diodes, Light
emitting diodes, photo diodes and clamping
diodes.
Transistors- Description of NPN, PNP, field-
effect transistor (FET), phototransistors.
Description of Integrated circuits.
Circuit protection devices- Description of
fuses, different type of fuses- glass or ceramic,
blade and bullet or cartridge fuses. Fusible
links, maxi fuses, circuit breaker, Positive
Temperature coefficient (PTC) resistor device

12
12
3 Diagnosis and remedy for- Speedometer Wiring and circuit diagrams- Automotive
shows no operation, fuel level meter Wiring- difference between primary wiring and
shows no operation, coolant temp meter secondary wiring. Comparison between solid
shows no operation, Oil pressure light and stranded primary wire.
shows no lighting. Description of wire size- Metric and American
wire gauge (AWG), Importance of ground
straps used in automotive wiring.
Description of different type of terminals and
connectors- Molded, multiple-wire hard shell,
bulkhead, weather-pack, metri-pack, heat-
shrink covered butt connectors.
Importance of printed circuit boards, wiring
harnesses, wiring diagrams and color codes and
circuit numbering.
Study of common electrical and electronic
symbols used in wiring diagrams.
4& Check and replace ignition coil, Ignition principles and Faraday’s laws,
5 overhauling Distributor Assembly. Primary and secondary winding of transformer,
Checking ignition timing, Checking & Ignition components, Spark plugs, Spark plug
changing a spark plug, Removing & components, Vacuum & centrifugal units, Plug
replacing contact points firing voltage, Contact breaker system, ballast
Diagnosis- Possible causes and remedy resistor coil, Dwell angle, Spark timing.
for Engine cranks, but will not or hard Battery power source, Description and function
to start, Poor fuel economy or engine of Capacitor/condenser, Distributors,
performance. Distributor types, High-tension leads, Advance
Identification and testing of Hall effect & retard mechanisms.
sensor, Optical sensor. Tracing and Principle of Induction –Mutual induction, self
testing of sensor circuits. Induction, Inductive system operation,
Tracing of Distributor less ignition Induction wiring, Hall effect sensors, Hall
systems circuit. effect operation, Optical type sensors
Distributor less ignition systems, Insulated
coils, Distributor less ignition system timing
6&7 Removing starter motor from vehicle, Starting system- purpose of starting system,
and Performance test for pull-in test, Staring system components, Starter motor
Hold-in test, pinion (plunger) return principles, study of starter control circuits.
test, No-load performance test. Starter motor construction, Starter magnet
Solenoid test for Hold in coil open types, Starter motor engagement,
circuit, Armature test – Ground test, Commutation, Switching, solenoid
Open circuit test, pull-in coil open construction..
circuit test, field coil test. Inspections of
brush length wear as per service
manual.
Trouble shooting , possible causes and
remedy for starter motor not running,
Starting motor running but too slow
(small torque), staring motor running,
but not cranking engine. Noise,
starting motor does not stop running.
Growler testing for rotors.
Checking a starting system, Jump-

13
13
starting a vehicle
8&9 Checking a charging system for the Charging system- The purpose of Charging
cause of undercharge, No charge, and system, charging system components, charging
over charge conditions. Removing & system circuit, Alternator principles,
replacing an alternator, Inspection of Alternating current, Alternator components,
rotor for ground, open circuit – field Rectification, Phase winding connections,
coil resistance, slip ring surface, Fan, Rotor circuit, Voltage regulation, System
bearing. Inspection of stator for operating voltage, High voltage charging
ground, open circuit, Inspection of systems, Rotor, Stator, Alternator end frames,
Drive end bearing rotation, Rectifier, Slip ring & brush assembly, Rectifier assembly,
brush length compare with service Alternator cooling fan.
manual. slip ring surface. Inspecting &
adjusting an engine drive belt,
Replacing an engine drive belt / pulleys
/ Tesnionsers and their alignments.
Trouble shooting, possible causes and
remedy for warning lamp does not glow
when ignition switch is on, Warning
lamp glows dim when ignition switch is
on, warning lamp ‘on’ while the
alternator is running, Warning lamp
glows ‘dim’ while the alternator is
running, warning lamp flickers
considerably.
10 - Identification of EDC components, Electronic Diesel control- Electronic Diesel
12 sensors, Testing of sensors and control systems, Common Rail Diesel Injection
actuators. (CRDI) system, Hydraulically actuated
Identification of various components of electronically controlled unit injector (HEUI)
MPFI system. Testing of MPFI diesel injection system. Sensors, actuators and
components and replacement if ECU (Electronic Control Unit) used in Diesel
necessary. Check delivery from fuel Engines.
Pump. Replacing a fuel filter. Introduction to Electronic fuel injection (EFI)
Identification of Electronic control Unit. fuel supply system, Multi-point injection
Set up for testing, Testing of Electronic systems (MPI/MPFI), EFI air cleaners,
Control Circuit. Fault finding in Electronic mufflers, EFI fuel supply system
Electronic circuit and remedies using components- Description of Fuel pumps, EFI
scan tool. sensors, Potentiometer, Auxiliary air valves,
Idle speed control devices, Inertia sensors.
Introduction to EFI Engine Management -
EFI operation Modes of EFI, Idle speed control
systems, Feedback & looping, Cold start
systems, Air measurement, Air-flow
monitoring, Variable intake manifold system,
Electrical functions, EFI wiring diagram,
Electronic control unit – ECU, EFI system
ECU, Electronic control unit settings, Engine
speed limiting, Malfunction indicator lamp.
Importance of Diagnostic Trouble Code (DTC)
& its general format. Use of scan tool and
retrievals of codes.

14
14
13 Identification of various sensors EFI sensors- Description, location and
installed in engine & its mounting. function of Intake Temperature sensor, Mass
Testing of Temperature sensor, airflow sensor, Manifold absolute pressure
Pressure senor, potentiometer, magnetic sensor, Air vortex sensor, Fuel system sensor,
induction sensor, cam shaft sensor, Throttle position sensor, Exhaust gas oxygen
crankshaft position sensor. sensor, Crank angle sensor, Hall effect voltage
sensor.
14 & Inspection of power steering control Steering, suspension and Brakes:-
15 module circuit. Checking & adjusting Description of Electric power assisted steering,
power steering fluid, Pressure testing a Basic electric power steering operation,
power steering system, Flushing a Electronic adjustable-rate shock absorbers,
power steering system. Electric brakes, Electro hydraulic braking
Trouble shooting and remedy for (EHB), ABS brake system, Antilock braking
steering wheel feels heavy at low speed, system operation, Principles of ABS braking,
poor recovery from turns, Vehicle pulls ABS master cylinder, Hydraulic control unit,
to one side during straight driving. Wheel speed sensors, ABS with Electronic
Identification of ABS components, Brake force Distribution (EBD) control unit.
checking of ABS warning lamp. Electronic control transmission -Electronic
Identification of Automatic control Unit, Fully hydraulically controlled
transmission components. transmission, Electronic shift programs,
Inspection of shift lever switch, throttle Manual selection
position sensor, speed sensor and
automatic transmission wiring harness
coupler.
16 & Identification of Air conditioning Heating Ventilation Air Conditioning
17 components, Performance test on A/c (HVAC) legislation, Vehicle heating,
unit, Checking Charged state of ventilation & cooling systems, Basic air-
refrigerant, Inspecting & adjusting an conditioning principles, Air-conditioning
engine drive belt, Replacing an engine capacity, Air-conditioning refrigerant,
drive belt. Humidity, Description and function of Fixed
Checking a heating system, orifice, Control devices, Thermostatic
Compressor rotation test, air Gap check, expansion valve system, Thermal expansion
Refrigerant recovery –evacuating – valves, Air-conditioning compressors,
charging of A/c system. Condensers & evaporators, Receiver drier,
Replenishing compressor oil level Lines & hoses, TX valve construction,
Trouble diagnose and remedy for Temperature monitoring thermostat,
No cooling or warm air, Cool air comes Refrigerants, Pressure switches, Heating
out only intermittently, cool air comes elements.
out only at high, Insufficient cooling, Air-conditioning ECU, Ambient air
Abnormal noise from compressor, temperature sensor, Servo motors, Electric
Magnetic clutch, condenser, evaporator, servo motors, Automatic climate control
Blower motor. sensors, Evaporator temperature sensor, Blower
Diagnosis test for High pressure gauge speed control, Ventilation systems.
–pressure high and low, Low pressure
gauge for pressure high and low.
18& Trace the light circuit - test bulbs, align Lighting system, Lamps/light bulbs,
19 head lamps, Aiming headlights. Lamp/light bulb information, LED lighting,
Changing a headlight bulb, Checking of Headlights-description of standard sealed
a head light switch and to replace if beam, halogen sealed beam, composite and
faulty. High intensity discharge (HID) headlights.
Trouble shooting and remedy for Headlight & dimmer circuits, Park & tail light

15
15
Headlight - headlight do not light up, circuits, Brake light circuits, turn signal
only one headlight does not light up, circuit, Cornering lights, Fog lights circuit,
Only one beam (“Hi” or “Lo”) does not interior lights- courtesy, reading and instrument
light.. panel lights, Smart lighting , Reverse lights.
Trouble shooting and remedy for turn
signal and hazard warning lights -Flash
rate high or one side only flashes, No
Flashing, flash rate low.
Trouble shooting and remedy for
clearance, tail and license plate lights -
All lights do not light up, some lights do
not light up.
Trouble shooting and remedy for Back-
up light - Back-up lights do not light up.
Trouble shooting and remedy for Brake
lights -Brake lights do not light up,
Brake light stay on.
Trouble shooting and remedy for fuel
meter and fuel gauge unit - Fuel meter
shows no operation or incorrect
operation.
Trouble shooting and remedy for
Engine coolant Temp (ECT) meter and
ECT Sensor – Engine coolant temp
meter shows no operation or incorrect
operation.
Trouble shooting and remedy for oil
pressure light – Oil pressure warning
light does not light up when ignition
switch is on at engine off.
Trouble shooting and remedy for brake
and parking brake warning light- Brake
warning light does not light up when
fluid flow level, Brake warning light
does not light up when parking brake
pull up, Brake warning lights stay on.
Trouble shooting and remedy for
interior light- Interior light do not light
up.
Trace the wiring circuit of traffic signal
flashers light circuit-tracing
defects in the flasher circuits, replacing
fuse bulb.
20 & Trouble shooting and remedy for Horn- Accessories: Horn circuit, wiper circuit, power
21 No horn operation, poor sound quality, window components and circuit. Power door
horn sounds continuously and to replace lock circuit, automatic door lock circuit, remote
the horn if faulty. keyless entry system circuit, antitheft system,
Remove and install wiper motors and immobilizer system. Navigation system, Car
wiper switches. Checking & replacing radio and cassette player, car videos.
wiper blades. Description and function of Airbags, Seatbelt,
Trouble shooting and remedy for Vehicle safety systems, Crash sensors, Seat belt

16
16
windshield wiper and washer - no pre-tensioners, Tire pressure monitoring
operation, intermittent operation, systems
continuous operation, and wipers will Integrated communications, Proximity sensors,
not park. Reflective displays, Global positioning
Diagnose causes for improper operation satellites, Triangulation/trilateration,
of the windshield washer system and to Telematics. Application of Automotive bus
replace the pump if faulty. system- currently used in cars: CAN (Control
Diagnose the power window system for Area Network) , LIN (Local Interconnect
– all power window motors do not Network), FlexRay™ and MOST(Media
operate, some switches do not operate. Oriented Systems Transport).
Diagnose the power door lock control , Importance of E/E Architecture
for – All power door locks do not
operate, only one power door lock not
operate.
Diagnose for remote keyless entry and
immobilizer system.
Familiarization of car radio wiring and
speaker circuits
Diagnose automatic seat belt systems,
Diagnose air bag system and service
warnings.
22-23 Industrial Training /Project
24-25 Revision and Test
26 NCVT Exam

17
17
Automobile Group – 1 year Trade
2nd Semster
Workshop Calculation and Science
Syllabus for the trade of Mechanic Auto Electrical & Electronics

Week Workshop calculation and


No. Science (3 Hrs/week)
Factorisation and quadratics: multiply expressions in brackets by a number, symbol or
1 & 2 by another expression in a bracket; by extraction of a common factor eg ax + ay, a(x + 2)
+ b(x + 2) ; by grouping eg ax − ay + bx − by ; quadratic expressions eg a2 + 2ab + b2 ;
roots of an equation eg quadratic equations with real roots by factorisation, and by the use
of formula
3 Geometry– Use of scientific calculator,/logarithmic table Angles -Angular measurement,
Angles and rotation, Examples of angles in automotive work, Adding and subtracting
angles. Types of angle- Adjacent angles, Opposite angles, Corresponding angles, Alternate
angle
4-6 Angles. Supplementary
Trigonometry- Types ofangles, Complementary
triangle - Acute angledangles,
triangle, Obtuse angled triangle,
Equilateral triangle, Isosceles triangle, Scalene triangle, Right angled triangle,
Labelling sides and angles of a triangle, Sum of the three angles of a triangle.
Pythagoras’ theorem, Circles, Ratio of diameter and circumference, Length of arc,
Timing marks, Wheel revolutions and distance travelled, Valve opening area.
Trigonometry- Using sines, cosines and tangents to solve vehicle problems.
7 -10 Formulae for Perimeter and Area of Plane figure - Rectangle, Square, Parallelogram,
Triangle, Hexagon, any regular polygon, Trapezium, Circle, sector, Fillet, Ellipse,
segment of a circle;
Formulae for Volume and surface area of solids- Rectangular solid, Prism, cylinder,
pyramids and cones, Frustum of pyramid and cones, sphere, Hollow sphere, segment of
sphere, circular ring, spherical sector,
Calculation of volume and weight of simple solid bodies such as cubes, square and
hexagonal prism-shop problem.
11-13 Statistics – Collecting and sorting raw data, Definition of Discrete variable, continuous
variable with Shop examples. Constructing pictographs-pie chart, Bar chart. Frequency
and tally Charts. Importance of the shape of a frequency distribution- histogram,
frequency polygon, Cumulative frequency plot. Interpreting statistics- sampling,
arithmetic mean, median,
14 & mode,and
Heat Range.
temperature –Temperature-Thermodynamic
Graphs- variables, scales, coordinates, straight line graphs.
temperature scale (Kelvin),
15 Cooling system temperature; Standard temperature and pressure (STP); Thermal expansion
with calculation; Heat- Sensible heat, Latent heat, Specific latent heat, Specific heat
capacity, Quantity of heat with calculation; Heat transfer – Conduction, Convection,
Radiation ;
16 & Heating, expansion and compression of gases - Absolute pressure, Absolute temperature;
17 Laws relating to the compression and expansion of gases -Heating a gas at constant volume,
Heating a gas at constant pressure, Charles’ law. Expansion or compression at constant
temperature – isothermal

18
18
18-20 Internal combustion engines- Engine power-Brake power, Horsepower, PS – the DIN,
Indicated power, Mean effective pressure, Calculation of indicated power, Cylinder
pressure vs. crank angle, Mechanical efficiency of an engine, Volumetric efficiency,
Torque vs. engine speed, Specific fuel consumption vs. engine speed, Brake power, torque
and sfc( Specific fuel consumption) compared, Brake mean effective pressure, Thermal
efficiency, Indicated thermal efficiency, Brake thermal efficiency petrol vs. Diesel.
21 Fuels and combustion- Calorific value, Combustion-Products of combustion, Relevant
combustion equations. Air–fuel ratio-Petrol engine combustion, Detonation, Pre-ignition,
Octane rating, Diesel fuel, Flash point , Pour point, Cloud point, Biofuels, Liquefied
petroleum gas (LPG) ,Hydrogen, Zero emissions vehicles (ZEVs)

19
19
Automobile Group –
2nd Semester
Engineering Drawing
Syllabus for the trade of Mechanic Auto Electrical & Electronics

Week Engineering Drawing (3 Hrs/week)


Nos. 2nd Semester
1-4 Read and interpret drawings- Determine information from the title block, Read and
interpret industrial prints, Read and interpret detailed and assembly drawings,
Identify casting drawings and machining drawings, Read and interpret diagrams,
Distinguish between a monodetail and a multidetail drawing.
5-8 Identify different drawing projections - Interpret pictorial and multi-view drawings.
Interpret auxiliary and section views, Determine views in a drawing and the
significance of the view being shown. Identify missing lines and missing views.
9-12 Free hand sketching of key and screw threads. Read and interpret three Types of
screw thread representation: pictorial, schematic and simplified presentation. Terms
used in describing a threaded Part, Designation of Thread Specifications, Left-Hand
Thread Notations, read and interpret the different type of Finish Symbols, Fillets and
Rounds and Machine Slots.
13 Make a simple sketch in plan view of a front engine FWD vehicle. Label the main
components: engine, clutch, gearbox, drive shafts, driving, wheels, radiator, fuel
tank.
14 Free hand Sketching of Fuel supply High Pressure system. Control unit
ingoing/outgoing information diagram.
15 Drawing of schematic diagram of ABS hydraulic circuit/Engine control module
assembly
16 Free hand sketch of Torque converter
Lay out for gearbox, Selector positions, Planetary gear set, High range power flow,
Low range power flow
17 Block diagram of MPFI system. Sketching of various Electronic devices used in
motor vehicle.
18 Free hand sketching of sensors. Free hand cut sectional view of petrol nozzle.
19 Sketching of Exploded view of alternator.
20 Sketching of Exploded view of starter motor.
21 Sketching of Air conditioning system using an expansion valve and orifice tube.

SYLLABUS FOR EMPLOYABILITY SKILLS


SEMESTER-II
(Pl ref to www.dget.nic.in)

20
20
21
21
TRADE: MECHANIC AUTO ELECTRICAL & ELECTRONICS

LIST OF TOOLS & EQUIPMNT

A. TRAINEES TOOL KIT per 4 Trainees FOR 20 TRAINEES +1 ISTRUCTOR

Sl.No. Item with specification Qty (Nos.)


1. Allen Key set of 12 pieces (2mm to 14mm) (5+1)
2. Back probe tools 6
3. Caliper inside 15 cm Spring 6
4. Calipers outside 15 cm spring 6
5. Center Punch 10 mm. Dia. x 100 mm. 6
6. Dividers 15 cm Spring 6
7. Electrician Screw Driver 250mm 6
8. Hammer ball peen 0.5 kg with handle 6
9. Hands file 20 cm. Second cut flat 6
10. Logic probe 6
11. Pliers combination 20 cm. 6
12. Screw driver 20cm.X 9mm. Blade 6
13. Screw driver 30 cm. X 9 mm. Blade 6
14. Scriber 15 cm 6
15. Spanner D.E. set of 12 pieces (6mm to 32mm) 6
16. Spanner, ring set of 12 metric sizes 6 to 32 mm. 6
17. Spanners socket with speed handle, T-bar, ratchet and universal upto 32 6
mm set of 28 pieces with box
18. Steel rule 30 cm inch and metric 6
19. Steel tool box with lock and key (folding type) 400x200x150 mm 6
20. Test light 6
21. Wire cutter and stripper 6

B. Tools Instruments and General Shop outfits

Sl.No. Item with specification Qty (Nos.)


1. AC alternator slip ring puller 1
2. Adjustable spanner (pipe wrench 350 mm) 2
3. Air blow gun with standard accessories 1
4. Air impact wrench with standard accessories 4
5. Air ratchet with standard accessories 4
6. Allen Key set of 12 pieces (2mm to 14mm) 2
7. Ammeter 300A/ 60A DC with external shunt 4
8. Angle plate adjustable 250x150x175 1
9. Angle plate size 200x100x200mm 2
10. Anti theft device 2
11. Anvil 50 Kgs with Stand 1
12. Auto Electrical test bench 1
13. Battery –charger 2
14. Battery terminal cleaner tool 2
15. Battery tester 1

22
22
16. Belt Tensioner gauge 1
17. Blow Lamp 1 litre 2
18. Caliper inside 15 cm Spring 4
19. Calipers outside 15 cm spring 4
20. Car Jet washer 1
21. Car stereo 1
22. Chisel 10 cm flat 4
23. Chisels cross cut 200 mm X 6mm 4
24. Circlip pliers Expanding and contracting type 15cm and 20cm each 2
25. Clamps C 100mm 2
26. Clamps C 150mm 2
27. Clamps C 200mm 2
28. Cleaning tray 45x30 cm. 4
29. Copper bit soldering iron 0.25 Kg 4
30. Cylinder bore gauge capacity 20 to 160 mm 4
31. DC Ohmmeter 0 to 300 Ohms, mid scales at 20 Ohms 4
32. Depth micrometer 0-25mm 4
33. Dial gauge type 1 Gr. A (complete with clamping devices and stand) 4
34. Distributor –Duel advance type, reluctance type 1 each
35. Dividers 15 cm Spring 4
36. Drift Punch Copper 15 Cm 4
37. Drill point angle gauge 1
38. Drill twist 1.5 mm to 15 mm (various sizes) by 0.5 mm 4
39. Electric Soldering Iron 230 V 60 watts 230 V 25 watts 2 each
40. Electric testing screw driver 4
41. Electrical horn ( different types ) 1 each
42. Engineer’s square 15 cm. Blade 4
43. Executive Auto Electrical tool kit 1
44. Feeler gauge 20 blades (metric) 1
45. File flat 20 cm bastard 4
46. File, half round 20 cm second cut 4
47. File, Square 20 cm second cut 4
48. File, Square 30 cm round 4
49. File, triangular 15 cm second cut 4
50. Files assorted sizes and types including safe edge file (20 Nos) 2 set
51. Flat File 25 cm second cut 4
52. Flat File 35 cm bastard 4
53. Glow plug tester 2
54. Granite surface plate 1600 x 1000 with stand and cover 1
55. Grease Gun 1
56. Growler 4
57. Hacksaw frame adjustable 20-30 cm 10
58. Hammer Ball Peen 0.75 Kg 2
59. Hammer Chipping 0.25 Kg 2
60. Hammer copper 1 Kg with handle 2
61. Hammer Mallet 2
62. Hammer Plastic 2
63. Hand operated crimping tool (i) for crimping up to 4mm and (ii) for 2
crimping up to 10mm

23
23
64. Hand reamers adjustable 10.5 to 11.25 mm, 11.25 to 12.75 mm, 12.75 2sets
to 14.25 mm and 14.25 to 15.75 mm
65. Hand Shear Universal 250mm 2
66. Hand vice – 37 mm 2
67. High rate discharge tester (cell tester) 1
68. Holders, lamp teakwood boards, plug sockets, solders, flux wires and As required
cables batteries round consumable blocks and other consumables as
required
69. Hollow Punch set of seven pieces 6mm to 15mm 2 sets each
70. Insulated Screw driver 20 cm x 9mm blade 4
71. Insulated Screw driver 30 cm x 9mm blade 4
72. Left cut snips 250mm 4
73. Lifting jack screw type 3 ton, 5ton & 20 Ton capacity 1 each
74. Magneto spanner set with 8 spanners 1 set
75. Magnifying glass 75mm 2
76. Marking out table 90X60X90 cm. 1
77. Multimeter digital 5
78. Multi-point fuel injection pump 1
79. Oil can 0.5/0.25 liter capacity 2
80. Oil Stone 15 cm x 5 cm x 2.5 cm 1
81. Oscilloscope 20MHz 2
82. Outside micrometer 0 to 25 mm 4
83. Outside micrometer 25 to 50 mm 4
84. Outside micrometer 50 to 75 mm 1
85. Outside micrometer 75 to 100 mm 1
86. Philips Screw Driver set of 5 pieces (100 mm to 300 mm) 2 sets
87. Pipe cutting tool 2
88. Pipe flaring tool 2
89. Pliers combination 20 cm. 2
90. Pliers flat nose 15 cm 2
91. Pliers round nose 15 cm 2
92. Pliers side cutting 15 cm 2
93. Portable electric drill Machine 1
94. Portable headlight aiming kit 1
95. Prick Punch 15 cm 4
96. Punch Letter 4mm (Number) 2 set
97. Right cut snips 250mm 4
98. Rivet sets snap and Dolly combined 3mm, 4mm, 6mm 4
99. Scriber 15 cm 2
100. Scriber with scribing black universal 2
101. Set of stock and dies - Metric 2 sets
102. Shear Tin Man’s 450 mm x 600mm 4
103. Sheet Metal Gauge 2
104. Sher Tinmans 300mm 8
105. Soldering Copper Hatchet type 500gms 5
106. Spanner Clyburn 15 cm 1
107. Spanner D.E. set of 12 pieces (6mm to 32mm) 4
108. Spanner T. flocks for screwing up and up-screwing inaccessible 2
positions

24
24
109. Spanner, adjustable 15cm. 2
110. Spanner, ring set of 12 metric sizes 6 to 32 mm. 2
111. Spanners socket with speed handle, T-bar, ratchet and universal upto 2
32 mm set of 28 pieces with box
112. Spark lighter 2
113. Spark plug spanner 14mm x 18mm x Size 2
114. Steel measuring tape 10 meter in a case 2
115. Steel rule 15 cm inch and metric 2
116. Steel rule 30 cm inch and metric 2
117. Straight edge gauge 2 ft. 1
118. Straight edge gauge 4 ft. 1
119. Stud extractor set of 3 2 sets
120. Stud remover with socket handle 1
121. Surface gauge with dial test indicator plunger type i.e. 0.01 mm 2
122. Tachometer (Counting type) 1
123. Taps and Dies complete sets (5 types) 1 set
124. Taps and wrenches - Metric 2 sets
125. Telescope gauge 4
126. Temperature gauge 0-100 deg c 2
127. Tester sparking plug ‘NEON’ Type 1
128. Thermostat 2
129. Thread pitch gauge metric, BSW 1
130. Timing lighter 1
131. Torque wrenches 5-35 Nm, 12-68 Nm & 50-225 Nm 1 each
132. Trammel 30 cm 2
133. Universal puller for removing pulleys, bearings 1
134. V’ Block 75 x 38 mm pair with Clamps 2
135. Vrnier caliper 0-300 mm with least count 0.02mm 4
136. Vice grip pliers 2
137. Voltmeter 50V/DC 5
138. Wire Gauge (metric) 5
139. Work bench 250 x 120 x 60 cm with 4 vices 12cm Jaw 1
140. 4 Point relays 2
141. 5 Point relays 2

C. General Installation/ Machineries

Sl.No. Item with specification Qty (Nos.)


1. Air bag simulator 1
2. Air conditioned MPFI vehicle with auto transmission and accessories 1
3. Air conditioning service Unit (Car) 1
4. Air conditioning trainer kit 1
5. Alternator assembly used for LMV 2
6. Arbor press hand operated 2 ton capacity 1
7. Bench lever shears 250mm Blade x 3mm Capacity 1
8. Cut section Model of Mock layout of a motor car –electrical system – 1
working model
9. Demonstration board Ignition system, ignition coil 1 set

25
25
10. Demonstration board of CRDI system working model 1
11. Demonstration board of MPFI system working model 1
12. Discrete Component Trainer / Basic Electronics Trainer 1
13. Drilling machine bench to drill up to 12mm dia along with accessories 1
14. Dual Magnetization Yoke : AC / HWDC, 230 VAC, 50Hz 1
15. Electronic engine control module 1 set
16. Grinding machine (general purpose) D.E. pedestal with 300 mm dia 1
17. wheels penetrant
Liquid rough andInspection
smooth kit 1 set

18. Memory keeper / Battery backups 1


19. Multi scan tool /ECU diagnostics kit 1
20. Petrol Engine(4-stroke) Motor Cycle/Scooter along with special tools 1
and accessories
21. Pipe Bending Machine (Hydraulic type) 12mm to 30mm 1
22. Pneumatic rivet gun 2
23. Spring tension tester 1
24. Starter motor axial type, pre-engagement type & Co-axial type 1each
25. Trolley type portable air compressor single cylinder with 45 liters 1
26. capacity AirInjection
Ultrasonic tank, along with equipment
cleaning accessories & with working pressure 6.5 1
27. kg/sq cm plant Oxy-Acetylene complete ( high pressure)
Welding 2
28. Welding Transformer ( 150-300 Amps) 1
29. Wiper motor assembly 2
30. Working Model of power windows 1

D. List of consumable:

Sl.No. Description Quantity

1. Assortment of diodes / electronic components As required


2. Automatic Transmission oils As required
3. Backing Soda As required
4. Battery cleaner spray As required
5. Battery- SMF As required
6. Brake fluids As required
7. Chalk, Prussian blue. As required
8. Chemical compound for fasteners As required
9. Diesel As required
10. Different type gasket material As required
11. Different type of oil seal As required
12. Drill Twist (assorted) As required
13. Emery paper - 36–60 grit , 80–120 As required
14. Fender cover As required
15. Gear oils As required
16. Hacksaw blade (consumable) As required
17. Hand rubber gloves tested for 5000 V 5 pair

26
26
18. Holders, lamp teakwood boards, plug sockets, As required
solders, flux wires and cables batteries round
consumable blocks and other consumables as
required
19. Hydrometer 8
20. Jumper wires As required
21. Lapping abrasives As required
22. Leather Apron 5
23. Petrol As required
24. Power steering oil As required
25. Radiator Coolants As required
26. Safety glasses As required
27. Steel wire Brush 50mmx150mm 5

E. Workshop Furniture

Sl. Description Quantity


No.
1. Book shelf (glass panel) 6½ ‘ x 3’ x 1½’ As required
2. Computer Chair 1+1
3. Computer Table 1+1
4. Desktop computer and related MS office software 1+1
5. Discussion Table 8’ x 4’ x 2½ ‘ 2
6. Fire Extinguishers, first- aid box As required
7. Instructional Material – NIMI Books/Ref.books As required
8. Internet connection with all accessories As required
9. Laser printer 1
10. LCD projector/ LED /LCD TV (42”) 1
11. Multimedia DVD for Automotive As required
application/subjects
12. Online UPS 2KVA 1
13. Stools 21
14. Storage Rack 6½ ‘ x 3’ x 1½’ As required
15. Storage shelf 6½ ‘ x 3’ x 1½’ As required.
16. Suitable class room furniture As required
17. Suitable Work Tables with vices As required
18. Tool Cabinet - 6½ ‘ x 3’ x 1½’ 2
19. Trainees locker 6½ ‘ x 3’ x 1½’ 2 Nos. to accommodate 20
Lockers

27
27
List of tools & Equipment for the Trade of
Mechanic Auto Electrical & Electronics - Engineering Drawing
(Note : Facilities available in Draughtsman trade can be utilized)
TRAINEE’S TOOLS KIT
Sl. No. Name of the items Quantity
1. Draughtsman drawing instrument box 20+1 set
2. Set square celluloid 45⁰ (250 X 1.5 mm) 20+1 set
3. Set square celluloid 30⁰-60⁰ (250 X 1.5 mm) 20+1 set
4. Mini drafter 20+1 set
5. Drawing board (700mm x500 mm) IS: 1444 20+1 set
GENERAL MACHINERY SHOP OUTFIT
Sl. No. Name & Description of Machine Quantity
1. Draughtsman table 20 Nos.
2. Draughtsman stool 20Nos.

28
28

You might also like