Professional Documents
Culture Documents
[SERVICE MANUAL]
Mstar MST719DU
1
MST719 Service Manual
Contents
1. Introduction chassis block diagram ----------------------------------4
1) Can’t work-------------------------------------------------30
4) No sound--------------------------------------------------33
2
MST719 Service Manual
!
1. warning!
2. Please confirm the power to Panel is +5V when change main board, if not ,the panel
3
MST719 Service Manual
CVBS
Audio R&L
Audio out
VGA_Auido
YPbPr
CVBS
CVBS_Out
Audio R&L
Y/C
U7 U8
U6
CN10
24C04 24C04
DVD socket
YPbPr PI5V330 RC4558
DVD switch
Tuner CVBS
Power
U4
Connect LIPS
Audio R&L Out
FLASH
U14 U26
PAL/SECAM EN25F40
BG/DK 74HC4052D 74HC4052D
Audio switch Audio switch MSTAR IC U20
DVD R&L
U13
IF
MST719DU
DVD socket CN8 CS4344 U21 U19
2D Combfilter
TV Audio HDMI DAC 2D interlace U18 24C32 24C04 CN21
X1 U10
U9 EEPROM HDCP
K9656M30 Speaker
NXP CVSB
X2 TDA9885TS Sound
K3953M30 Audio Out AMP ADC processor&
PCM1808 TAS5707
U28
U27 SN74LVC1GX04DCK
U16
2 X 5W
IR Board
LCD Panel
IR
4
MST719 Service Manual
2.MST719 IC Introduction
1).features description
5
MST719 Service Manual
6
MST719 Service Manual
7
MST719 Service Manual
8
MST719 Service Manual
9
MST719 Service Manual
10
MST719 Service Manual
11
MST719 Service Manual
12
MST719 Service Manual
3. TAS5707 IC Introduction
1) Features description
13
MST719 Service Manual
14
MST719 Service Manual
15
MST719 Service Manual
16
MST719 Service Manual
4. TDA9885 IC Introduction
1) features description
17
MST719 Service Manual
Block diagram:
18
MST719 Service Manual
19
MST719 Service Manual
20
MST719 Service Manual
21
MST719 Service Manual
22
MST719 Service Manual
6. SN74LVC1GX04DCK IC Introduction
23
MST719 Service Manual
7. EN25F40 IC Introduction
24
MST719 Service Manual
25
MST719 Service Manual
b) PI5V330 (U6) for option external module DVD or USB with YPbPr signal switch,If
not use DVD or USB function this IC no need install.
c) RC4558 (U4) for AV output audio amplifier, because the external audio signal by
74hc4502D switched the audio level not enough(under 620MVrms).
26
MST719 Service Manual
27
MST719 Service Manual
28
MST719 Service Manual
CN17 (For HDMI EDID Loading)
NO. Symbol Function Electronic parameter
1 WP
2 SDA
3 SCL
4 GND
5 +5V
CN20 ( Panel Power supply Selection )
NO. Symbol Function Electronic parameter
1 +12V Option +12V
2 Optional panel VCC Select power to panel power supply
3 +5V Option +5V
4 +3.3V Option +3.3V
6. Usual fault
1), Can’t work(fault description: LED is off or red LED is always on )
N
Check if the I2C of U18 pin61,pin62 and the
U21 I2C pin software data is ok. Check U20
flash IC is work and the software data
normal operation.
30
MST719 Service Manual
N Y
Firstly check if the power supply Check if the voltage of the CN21 pin4 STB
output 12V, 5VS and 5V_STB is ok. on/off is high level to 4.5V
N
Check the pin voltage of the Check the component Q7 and the relevant Y
connector CN21 pin 11 Bright on/off circuit work normal. Then check MST719
control is high level to 4.0V pin55 control level is low.
31
MST719 Service Manual
First check the LVDS line connect 1. Change the LVDS line.
from main board to panel interface N 2. If have not +5V power supply,
is OK, then check the panel supply Check U3 5V switch and MST719
power +5V I/O control circuit.
Y
N
As per input source picture If all the work condition are ready but
abnormity, Check TV source of still picture abnormity try to change
TDA9885,tuner ect. circuit. MST719 main IC.
AV,S-Video,VGA,Ypbpr,HDMI socket
to MST719 input circuit.
32
MST719 Service Manual
4). No Sound
N
Y
Check if the power supply FB8 12V NO Check the CN21 pin 8,9 power
is ok, FB5,FB16 +3.3V is OK. supply output 12V OK or not.
Check if the U16 TAS5707 pin 19 Check the Q23,Q21 and the I2C
voltage is high to 3.6V, Check the NO circuit.
pin23,24 software is ok.
Y
NO
1.U27 PCM1808 is the ADC IC,If not Check the power supply circuit or
sound output to speaker, need change the component of crystal.
check this IC work status, please
check the power supply: +3.3V and
5VS is ok or not. 2.U28 is the
crystal oscillation driver IC, check
the pin6 +3.3V is OK then check
the frequency of pin6 is 12.288M
33