You are on page 1of 4

Exam: SA-2- April - 2017

Date: 18/04/2017 B.E.P.M.S

Time: 60 Minutes Std. 9 Total Mark: 40

Instruction: The question paper contains 40 questions. Each question carries 1 Mark

1) ___________coating is done on a galvanized sheet.


A) Brass B) Tin C) Copper D) Zinc
2) ___________ Sheet is used for Medical tools, dairy & food processing tools.
A) Stainless steel B) Galvanized C) Copper D) Tin
3) If the gauge number is high that means sheet is______?
A) Thicker B) Thinner C) Lighter D) Smaller
4) _______________sheet used to support sheet metal for making it flat and straight.
A) Hammer B) Snip C) Flatter D) Anvil
5) The process of joining two ends of a sheet metal by different ways is called ________.
A) Seaming B) Wiring C) Bending D) Hollowing
6) Flux is used __________process.
A) Forming B) Punching C) Hollowing D) Wiring
7) _____________used to cut thick sheet metal.
A) Hammer B) Snip C) Hand shear D) Set Hammer
8) The worker is known as ______who made product form metal sheet.
A) Welder B) Tinsmith C) Carpenter D) Forman
9) Gauge number for sheet metal shows its________.
A) Thickness B) Thinness C) Length D) Breadth
10) ___________ Sheet is used in domestic utensils aircraft and automobile industry.
A) Stainless steel B) Galvanized C) Copper D) Aluminum
11) ____________ is responsible for the process of corrosion.
A) Oxidation B) Lubrication C) Reduction D) Moisture
12) Which factor is affect form atmosphere to the corrosion process?
A) Carbon B) Oxygen C) Hydrogen D) None
13) Clearance between two parts is a result of __________.
A) Tear B) Wear C) Crack D) Friction
14) Rapid wearing away of parts in a short time is called _________.
A) Normal wear B) Abnormal wear
C) Proper wear D) Improper wear
15) Machine parts are subjected to __________due to constant use.
A) Wear B) Friction C) Fatigue D) Rusting
16) ______________is used to check wear in the alignment of shaft and bearing.
A) Feeler gauge B) Venire caliper
C) Micro meter D) pitch gauge
17) ____________maintenance is done before break down of plant or machine.
A) Corrective B) Preventive C) Break down D) None
18) To reduce the friction ____________is used.
A) Oxidation B) Lubrication C) Reduction D) Maintenance
19) _____________is used to check wear on cylindrical parts.
A) Feeler gauge B) Venire caliper
C) Micro meter D) pitch gauge
20) _____________type of maintenance is undertaken when machine stops working.
A) Corrective B) Preventive C) Break down D) None
21) ___________ should not be used to put off fire due to Electricity.
A) Salt water B) Liquid carbon Dioxide C) Carbon D) Ethanol
22) Opening or lifting fragile substance wrongly is an example of ____________.
A) Unsafe working method B) Unsafe work place
C) Safe working method D) Safe work place
23) __________should not be spilled on floor in Electric Workshop.
A) Kerosene B) Water C) Oil D) Grease
24) ____________should be used in circuit for Electrical safety.
A) MCB B) Plug C) Socket D) Switch
25) Feeling of insecurity in job can lead to ___________.
A) Safety B) Accident C) Maintenance D) Any
26) Gas cylinder for gas welding should be moved by________.
A) Rolling B) Dragging C) trolley D) By pushing
27) All wires should be treated as _____________unless otherwise confirmed
A) Phase B) Neutral C) Earthling D) Any
28) _________ should not be spilled on floor in mechanical workshop.
A) Kerosene B) Water C) Oil D) Grease
29) _________ is done to prevent major break down in machinery.
A) Repairing B) Maintenance C) Cleaning D) None
30) ________is used to put off fire due to short circuit.
A) Water B) Liquid carbon Dioxide
C) Carbon D) Acid Chemical
31) Name the process done by using Die & punch press?
A) Shearing B) Extrusion C) Embossing D) Joining
32) ________°tempreture is needed for soldering
A) 400 B) 200 C) 100 D) 300
33) Which process is used for making tube, rod& thin wire?
A) Hot drawing B) cold drawing C) Forging D) Rolling
34) Up to what mm thickness metal can be coated in electroplating?
A) 0.005 B) 0.2 C) 0.005 to 0.2 D) 5
35) What is metal removing process called?
A) Hot drawing B) Machining C) Bending D) metal casting
36) Which is solder metal?
A) Tin-Zinc B) Tin- Lead C) Copper - Zinc D) Zinc- Lead
37) Which process is used to prepare tooth paste tube?
A) Bending B) Shearing C) Forging D) Extrusion
38) To join cutting tips on a turning tools___________ process is done.
A) Soldering B) Welding C) Brazing D) Revelting
39) ___________is made by cold drawing process.
A) Cylinder B) Plate C) Wire D) Gun
40) Extra metal added during brazing is called____________.
A) Electrode B) Filter C) Spelter D) None
…………………….*******************……………………………********************

You might also like