Professional Documents
Culture Documents
1.True or False
A hub forwards any signal received from any port to all other ports .
√ ×
Correct answer:
√
2.True or False
In broadcast network of OSPF protocol, any two DR Others will neither exchange LSA nor send Hello packet to each other due to the
existence of DR.
√ ×
Correct answer:
×
3.True or False
When network condition changed, a static route can be rectified automatically without reconfiguration by the network administrator .
√ ×
Correct answer:
×
4.True or False
One of the significant features of the PPP protocol is the authentication function.A PPP connection is established only when the
authentication is successful.
√ ×
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 1/20
9/18/2018 Show question answer
Correct answer:
√
5.True or False
If you want to reset the routers configuration. The administrator need to delete the configuration files saved in the storage devices and
then rebooting the router.
√ ×
Correct answer:
√
6.True or False
Root bridges only provide root ports .
√ ×
Correct answer:
×
7.True or False
The fram-relay map information is show as below. The IP address 10.1.1.2 is configured on the local device.
[RTA]dis fr map-info
Map Statistics for interface Serial0 (DTE)
DLCI = 100, IP INARP 10.1.1.2, Serial0
create time = 2007/06/04 17:34:59, status = ACTIVE
encapsulation = ietf, vlink = 20, broadcast
√ ×
Correct answer:
×
8.True or False
The ICMP protocol (RFC792) is not applied to Application Layer but Network Layer.
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 2/20
9/18/2018 Show question answer
√ ×
Correct answer:
√
9.True or False
When you configure Frame Relay on Quidway routers, you can configure Inverse ARP instead of static address mapping because the
function of Inverse ARP is to provide dynamic address mapping.
√ ×
Correct answer:
√
10.True or False
If the optimal path to the destination IP address is unavailable after a change occurs in a network topology, the dynamic routing protocol
can make adaptation to this change and determine another optimal path to the destination IP address.
√ ×
Correct answer:
√
11.True or False
A static route can be either configured manually by a network administrator or generated automatically.
√ ×
Correct answer:
×
12.True or False
Routing Information Protocol (RIP) is available in the RIPv1, RIPv2, and RIPv3 versions.
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 3/20
9/18/2018 Show question answer
√ ×
Correct answer:
×
13.True or False
A Trunk port always sends tagged frames to the peer equipment.
√ ×
Correct answer:
×
14.True or False
In 802.1Q, a four byte field is inserted into the ethernet frame, but only 12 bits is used for VLAN ID?
√ ×
Correct answer:
√
15.True or False
When a trunk port receive an untagged frame , the switch will drop the frame.
√ ×
Correct answer:
×
16.True or False
A MAC address has 32 bits, the first 16 bits represent the manufactor.
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 4/20
9/18/2018 Show question answer
√ ×
Correct answer:
×
17.True or False
On a port running frame relay,We can apply several logical sub-interface, and in each logical sub-interface, one or more MAP items can
exist.
√ ×
Correct answer:
√
18.True or False
One router forwards the packets according the routing table on itself without considering the routing table of any neighbor routers.
√ ×
Correct answer:
√
19.True or False
In OSPF protocol, most of the packets are sent by using reserved multicast address and unicast. This can reduce the impact on non-
OSPF speaking devices.
√ ×
Correct answer:
√
20.True or False
RTA connects with RTB through interface Serial0. The configuration on RTA is as follow:
[RTA]aaa
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 5/20
9/18/2018 Show question answer
√ ×
Correct answer:
√
21.Single
In Window XP system, which of the following commands is used to release the IP address assigned by the DHCP Server?
a.ipconfig /all
b.ipconfig /renew
c.ipconfig /release
d.ipconfig
Correct answer:
c
22.Single
multiple PCs are connected to the same hub through twisted pair cables. What's its logical topology structure?
a.Star
b.Tree
c.Mesh
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 6/20
9/18/2018 Show question answer
d.Ring
e.Bus
Correct answer:
e
23.Single
Which class does IP address 190.233.27.13 belong to?
a.A
b.B
c.C
d.D
Correct answer:
b
24.Single
The data forwarding of the switch is based on ( ).
c.Source IP address
d.Destination IP address
Correct answer:
b
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 7/20
9/18/2018 Show question answer
25.Single
Each router only knows how to forward the packet to the next hop IP address. It doesn't know the end to end forwarding path. This type
of forwarding is called ( )
Correct answer:
a
26.Single
According to OSI reference model, switch operates at ( ) layer.
a.Physical
b.Data link
c.Transport
d.Application
Correct answer:
b
27.Single
Which of the following applications can be used to detect the path along which the data packets are transmitted from the source to the
destination?
a.Route
b.Nestat
c.Tracert
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 8/20
9/18/2018 Show question answer
d.Send
Correct answer:
c
28.Single
Which of the following is used by routers to forward the packets on the network?
a.DNS lookups
b.ARP tables
c.Routing tables
Correct answer:
c
29.Single
Which of the following is the broadcast MAC address?
a.FF-FF-FF-FF
b.FF-FF-FF-FF-FF-FF
c.00-00-00-00-00-00
d.00-00-00-FF-FF-FF
Correct answer:
b
30.Single
After a change occurs in a network topology, which of the following routes does not change automatically but changes only after the
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 9/20
9/18/2018 Show question answer
a.RIP route
b.OSPF route
c.BGP route
d.Static route
Correct answer:
d
31.Single
OSPF takes the precedence to select ( ) as a router ID unless you specify a router ID manually.
c.127.0.0.1
Correct answer:
a
32.Single
Which of the following standards is defined by IEEE to regulate the implementation of VLAN between switches?
a.802.1x
b.802.1d
c.802.1q
d.802.3
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 10/20
9/18/2018 Show question answer
Correct answer:
c
33.Single
After OSPF divides an AS into different areas, what type of information is send between these areas?
Correct answer:
a
34.Single
What does the distance vector routing protocol focus on according to the discovered routes and calculated routes?
c.Whether the egress port on the route belongs to a port aggregation group
Correct answer:
a
35.Single
What is the main function of DNS?
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 11/20
9/18/2018 Show question answer
b.Remote Access
c.File Transfer
d.Mail Transfer
Correct answer:
a
36.Single
Which of the following descriptions about function of VRRP is true?
d.VRRP provides the same default gateway for different network segments, thus simplifies gateway configuration of PCs in the
network
Correct answer:
a
37.Single
The protocol data unit that resides at network layer is called ( ).
a.Segment
b.Packet
c.Bit
d.Frame
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 12/20
9/18/2018 Show question answer
Correct answer:
b
38.Single
Which of the following parameters is used by RIP to calculate the value of cost?
a.MTU
b.Delay
c.Bandwidth
d.Hop count
Correct answer:
d
39.Single
On VRP platform, which of the following is the default route preference value for OSPF routing protocol?
a.10
b.1
c.100
d.120
Correct answer:
a
40.Single
Which of the following descriptions about learning state in STP is incorrect?
b.The port in learning state can learn the source MAC address of data packet
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 13/20
9/18/2018 Show question answer
c.The port in learning state can only learn the source MAC address but cannot transmit the data packet.
d.The port in learning state can forward part of the data packet
Correct answer:
d
41.Single
In STP calculation, a port identifier consists of two parts: one-byte ( ) and one-byte port number.
a.Port priority
b.Link priority
Correct answer:
a
42.Single
This device is used between the zones with different security level, control the information exchanged between two networks, enforce
the implementation of unified security policy, and prevent the intruder from copying and accessing the important information illegally. In
short words, it protects the security of the system. Which of the following devices provides the function mentioned above?
a.Firewall
b.Gateway
c.Router
d.IDS
Correct answer:
a
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 14/20
9/18/2018 Show question answer
43.Single
The network address of 125.3.54.56 with default subnet mask is ( )
a.125.0.0.0
b.125.3.0.0
c.125.3.54.0
d.125.3.54.32
Correct answer:
a
44.Single
Which of the following class has the first octet beginning with "1110"?
a.Class A
b.Class B
c.Class C
d.Class D
Correct answer:
d
45.Single
VLAN is short for?
Correct answer:
a
46.Multiple Choice
Which of the following statements regarding the route preference are correct?
Correct answer:
bcd
47.Multiple Choice
A routing table can be formed by using different methods. Which of the following protocols are used to form a routing table?
c.Application-level protocol
d.Transport-level protocol
Correct answer:
ab
48.Multiple Choice
The evolution of firewall technology goes through the following three stages, and these stages include ( )
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 16/20
9/18/2018 Show question answer
b.Proxy firewall
c.Stateful firewall
d.Link-layer firewall
Correct answer:
abc
49.Multiple Choice
What functions does a router mainly provide?
Correct answer:
acd
50.Multiple Choice
Which of the following applications are based on the TCP protocol?
a.PING
b.FTP
c.TELNET
d.OSPF
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 17/20
9/18/2018 Show question answer
Correct answer:
bc
51.Multiple Choice
OSPF routers are classified into four types. Which of the following statements about interior routers (IRs) are true?
d.If all the ports on an IR belong to area 0, this IR functions as a backbone router.
Correct answer:
ad
52.Multiple Choice
Packet filtering firewall filters packet based on quintuplet. Which of the following are the components of quintuplet?
a.IP address
b.Protocol number
c.Port number
d.Application program
e.MAC address
Correct answer:
abc
53.Multiple Choice
Which of the following statements are incorrect?
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 18/20
9/18/2018 Show question answer
d.For those routes to the same destination on VRP platform, the one with higher preference value is more preferred over the one
with lower preference value.
Correct answer:
cd
54.Multiple Choice
Which of the following devices operate at data link layer?
a.Hub
b.Bridge
c.Switch
d.Router
e.Firewall
Correct answer:
bc
55.Multiple Choice
Which of the following statements regarding RIP routing information are correct?
a.User can specify the route preference of RIP higher than that of static routes.
b.If the route calculated by other routing protocol which is imported by RIP does not specify the cost value, the cost value will be set
as 1 by default
c.User can specify the route preference value of RIP lower than that of direct routes.
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 19/20
9/18/2018 Show question answer
Correct answer:
ab
close
http://e-learning.huawei.com/exam/usermain/paper/userpaper.viewuserhispaperqueslist.flow?p_id=5384789881637533&trys=6&rserverid=100 20/20