You are on page 1of 6

BreakMaster™ Load

Interrupter Switch
Typical User Configurations

The complete line of BreakMaster load interrupter switches can fill most distribution system requirements.
They are available in a variety of configurations to meet specific distribution needs, including: single switches,
two-position no-load selector switches, duplex switches, and line-ups. Motor operators, customer metering
and outdoor construction are also available.

Standard Configuration Features Single Duplex Selector Line-up


35” width ● ●
70” width ●
90” indoor height, 99” outdoor height ● ● ● ●
50” depth standard (includes arrester if required), 60” depth available ● ● ●
90” depth (requires rear access to equipment) ●
Available section widths: 55” mains/tie; 35” branches; 20” / 35” incoming

terminal compartments; 20” / 35” / 40” auxiliary sections
Extension required for oil-filled transformers only (18” wide) ● ● ● ●
Dry type and cast coil transformers require 3” in throat for outdoor enclosure ● ● ● ●
Key interlocking standard between switches and fuse compartment ● ●

Single Duplex Selector Line-up (main-tie-main)

Switch Ratings (In accordance with Standards in table at bottom right) Typical Weights
Impulse Amperes Momentary Fault Weight (lbs.)
Max kV Withstand Continuous Switch Close Configuration NEMA 1 NEMA 3R
kV (BIL) and Interrupting Closed Asym Asym
Single 1200 1550
600 40,000 40,000 Selector 2500 3200
600 61,000 61,000 Duplex 2500 3200
60 1,200 40,000 40,000 Mains/Ties 1800 2400
1,200 61,000 61,000 Branch 1200 1550
5.0 600 40,000 40,000 20” wide incoming cable 600 850
600 61,000 61,000 35” wide incoming cable 1050 1400
95 1,200 40,000 40,000
1,200 61,000 61,000
600 40,000 40,000 Standards
600 61,000 61,000
15.0 95 1,200 40,000 40,000 C37.20.3
1,200 61,000 61,000 ANSI/IEEE C37.20.4
C37.22
NEMA SG-6
Fuse Ratings IEC 60265
UL See ANSI standards
Fuse Fuse Type Voltage Class Ampere Range
C22.2, No. 31
5 kV 25A - 900A CSA C22.2, No. 193
Current Limiting Fuses EJO-1
15 kV 20A - 300A
RBA200 5 kV - 15 kV 40E - 200E
RBA400 5 kV - 15 kV 20E - 300E
Expulsion Fuses
RBA800 5 kV - 15 kV 450E-720E
For a complete list of available fuses, contact factory or refer to publication DET-266
(available first quarter 2001).
BreakMaster BreakMaster: rugged, efficient, versatile
load switching and protection

GE’s BreakMaster™ load interrupter switches provide


dependable, economical load switching and protection for
medium voltage circuit applications from 2.4kV through
15kV in 600 or 1200 ampere load interrupting ratings.

The BreakMaster switch consists of a 2-position (open,


closed), 3-pole, gang-operated, air interrupter switch
utilizing a spring charged mechanism for both closing
and opening functions. It is operated externally from
the front of the cubicle and is equipped with a quick
make/quick break mechanism that opens and closes
the switch regardless of the speed at which the operating
handle is moved.

Used mainly as a primary or secondary disconnect switch


for transformers, the variety of configurations in which
BreakMaster is available also make it useful for specific
distribution needs. It can, for example, be inserted as a
main or feeder switch in PowerVac switchgear or LimitAmp
motor controller lineups. Fault current protection is
available using a complete line of current limiting or
expulsion fuses.

BreakMaster components are manufactured under strict


quality guidelines, and they meet or exceed all applicable
ANSI, NEMA, and IEEE standards (see “Standards” table
on fold-in page), plus IEC 60265 for limited purpose
switches. UL Listed switches are available for most
standard configurations and options. When required,
BreakMaster switches also meet the seismic requirements
of the UBC and CBC Zone 4 building codes. All steel
surfaces are chemically cleaned prior to painting with
an ANSI 61 finish that is rated for 1000-hour salt spray.
Oversize inspection
window Full height
interphase barrier

Provisions for key


interlocks

Two, heavy-duty
11 gauge doors

Safety mechanical
interlock

Easily accessible Rigid bolted frame


ground bus construction
An array of optional multi-
function meters measure Standard Features
volts, amps, frequency, power
factor, watts and VARs, and • Copper silver-plated bus
can communicate via RS-232, • Full length ground bus
RS-485, Commnet and Modbus. • Polyester coat paint
For safety, an enclosed, low • ANSI 61 paint color (gray)
voltage panel completely • Oversized viewing window
isolates metering components. • Full height interphase barriers
• 11 gauge doors, barriers and covers
• Generous cable termination area
While accessing fuses, split • Permanent non-corrosive nameplate
door prevents access to the • Individual doors over switch and fuses
live side of the switch when • Concealed door hinges
the lower door is open. • Switch padlock provisions
Oversized viewing window • Key interlock provisions
and switch position markers • Split rear and side covers
allow visual verification of • Tungsten-tipped arc interrupting blade
switch position. • Mechanical switch and door interlocking
• Louvered ventilation at top and bottom
• Safety horizontal barrier
Full height interphase barriers
are standard on all switches.
Both current limiting and
Standard Outdoor Features
expulsion fuses are available.
• Removable filters for louvers
• Long life space heaters
• 4” channel base
• Sloped roof
• Bottom closure plates
• Rodent barriers

Standard 50” section depth


provides substantial space Optional Accessories and Features
for incoming or outgoing
cables. 60” depth is also • UL / cUL listing
available when customer • Copper tin-plated bus
preference and/or specific • Insulated bus and bus boots over joints
options require additional • 80kA momentary bus rating
space. • Weather resistant
• Dust resistant
• Nema 2 drip-proof enclosure
• Rear doors (full height or double)
Horizontal barriers between • Vertical barriers
the switch mechanism and • Rodent barriers
fuse compartment are a • Bottom closure plates
standard safety feature. • Seismic Zone 4 bracing
• Tamper resistant hardware
• Auxiliary switches (2NO-2NC)
• Thermostat
• Space heater (standard on outdoor,
optional on indoor)
• Porcelain insulators
• Customer metering
Convenient split rear covers
• Surge arresters
provide easy access to
• Mimic bus
cable terminations or
• Space heater switch
devices located in the rear
• Ground studs
of the section.
• Convenience light
• Duplex receptacle
• Top hat
• Run back bus
• And more!
Other dependable power distribution products from GE

ZTS Series automatic transfer switches from GE LimitAmp® motor control centers provide an
Zenith Controls are the preferred standard for economical means of centralizing motor starters and
quality and reliability in the related control equipment. They
electrical industry, providing permit motor control starters,
that same quality for installations feeders, isolator switches,
from 5kV to 15kV. Designed distribution transformers,
for use in the most critical interlocking relays, programmable
applications – hospitals, military control, metering and other
sites, airports, communications miscellaneous devices to be
facilities, computer installations obtained in a single floor-mounted
where emergency or standby structural assembly fed from
applications exist -- they meet a common enclosed main bus.
the need for dependable Sections are bolted together to
continuity of power. form a single line-up assembly.
The entire center may be powered by incoming
line connection at a single point. When possible,
LimitAmp motor control centers bear UL section
PowerVac® switchgear combines the features of met- and unit labels.
alclad construction with vacuum interrupter technology
in the manufacture and
design of a superior class GE liquid-filled transformers are designed for such
of medium voltage switch- industrial and commercial applications as chemical,
gear. Vacuum interrupter cement and manufacturing
technology is recognized facilities, paper or steel
for its many benefits over mills, schools, hospitals
other arc interruption and office buildings.
technologies. Its clean, They use sealed-tank
quiet, durable design, construction that
first introduced in 1977, effectively contains the
continues to offer customers windings and most live
reliable service throughout parts in a controlled
the world. atmosphere. When
specified, less flammable
liquid-filled units may be installed indoors.

For additional information on


BreakMaster load interrupter switches
or any of these related products,
contact your local GE sales office
or visit us at www.GEindustrial.com

GE Industrial Systems
General Electric Company
41 Woodford Avenue, Plainville, CT 06062
www.GEindustrial.com
DEA-052B 0701 © 2001 General Electric Company

You might also like