You are on page 1of 10

®

THE PEELLE COMPANY


FREIGHT DOORS I CAR GATES I CAR ENCLOSURES

226
LIGHT CURTAIN
INSTALLATION GUIDE
GUIDE

4697 & 4698 Series

VSD
VERTICALLY
SLIDING 04/23/2014 - V1
DOORS
IMPORTANT INFORMATION
FOLLOW THE INSTRUCTIONS GIVEN IN THIS MANUAL CAREFULLY. FAILURE TO DO SO MAY CAUSE CUSTOMER
COMPLAINTS, INJURY, AND / OR SERIOUS CALL BACKS. KEEP INSTRUCTION MANUAL ON SITE.

DO NOT USE THIS PRODUCT IN EXPLOSIVE ATMOSPHERES, RADIOACTIVE ENVIRONMENTS OR FOR MEDICAL
APPLICATIONS! USE ONLY SPECIFIC AND APPROVED DEVICES FOR SUCH APPLICATIONS OTHERWISE SERIOUS
INJURY OR DEATH OR DAMAGE TO PROPERTY MAY OCCUR!

THIS DEVICE MUST NOT BE USED AS A PROTECTIVE DEVICE FOR DANGEROUS MACHINERY NOR IN
EXPLOSIVE ATMOSPHERES OR RADIOACTIVE ENVIRONMENTS

IT IS IN THE SOLE RESPONSIBILITY OF THE PLANNER AND/OR INSTALLER AND/OR BUYER THAT THIS PRODUCT
IS USED ACCORDING TO ALL APPLICABLE CODES AND STANDARDS IN ORDER TO ENSURE SAFE OPERATION
OF THE WHOLE APPLICATION.

ANY CHANGE OF THE DEVICE BY THE BUYER OR USER MAY RESULT IN AN UNSAFE CONDITION.

PEELLE DENIES EVERY LIABILITY AS WELL AS WARRANTY CLAIMS WHICH RESULT FROM SUCH
MANIPULATION.

CAUTION!
GATE
THE LIGHT CURTAIN IS DESIGNED TO DETECT
PASSENGERS AND FREIGHT OF A SPECIFIC SIZE

OBJECTS SMALLER THAN THE SPACING BETWEEN LIGHT CURTAIN


SENSORS
THE LIGHT BEAMS MAY NOT BE DETECTED.
TRANSPARENT OBJECTS MAY NOT BE DETECTED.

AVOID IMPROPER USE

THE PEELLE COMPANY 1


226
LIGHT CURTAIN
FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
INSTALLATION GUIDE
TECHNICAL SUPPORT 1-800-787-5020 ext 275
edge, the control unit as well as the pluggable be switch
allow a industrial car gate to close. However, if one device
cables. checks all relevant safety circuits including Figure 2
or more beams are interrupted, the output signal is the output relay. If this internal test is successful, the sensor e
Introduction
inactivated in order to prevent the gate from closing Safety
output Integrity
relay closes Check its contacts and allows the
Block diagram installatio
or to reopen the gate during closing. door/gate to operate. If this internal test fails, the
Because
Therelay the light2curtain
Figure is a safety device,
The light curtain is an optoelectronics sensor. A number of output contactsshows remain the openblock and prevent diagramtheof Factory s
The light curtain is an optoelectronic sensor. safety mechanisms
the light must
curtain. inAsa dangerous be integrated
indicated, itway. by theofuser,
consists an
infrared beams, emitted bybeams,
an emitter edge and received door/gate operating
A NCnumber of infrared emitted by an emitter so emitter
that itsand safe functioning
a receiver edge is thatensured.
are connected Its safe with
by a receiver
NO
edge, separated by a given
NC NO
edge and received by a receiver edge, separated distance, form bya Jumper
functioning
detachable cancables
be guaranteed
to the control using unit. a "test signal".
grid that
a COMMON is called a light curtain.
given distance, form a gridCOMMON If all infrared beams
that is called a light are
The Important
signal is putsafety eithernotes: in an end position of the gate
free (not interrupted),
curtain. If all infraredan outputbeams
signal isare activated,
free e.g. (notto
or
Thisontest a sequence
high-level must control. This
be implemented test signal otherwise puts Jumpe
allow an industrial
interrupted), an gate
outputto close.
signalHowever,
is activated,if one or
e.g. moreto the light curtaincannot into be a1 guaranteed!
WAGO 6 x 5.08
test mode where the
a safe operation Positio
beams
Figure are
allow interrupted,
a1:industrial
Light
car the
gateoutput
Curtain Function signal
to close. is inactivated
However, if onein device checks all relevant safety circuits including Set
2
order to prevent the gate from closing
or more beams are interrupted, the output signal or to reopen the is the output relay.toIf this
N
internal test Input”
is successful, the
Please refer section
P
3
“Test for more
gate
The during
Peelle
inactivated closing.
light tocurtain
in order preventlight
the gate curtain
from isclosing output relay closes
4
its 5 contacts and 250allows the
application details.COMMON VAC / 8 A

especially designed Not set


the gate to avoidclosing.
a collision between a NC
or to reopen during door/gate to operate. If 6 this internal test fails, the
125 VDC / 0.5 A
The safety
closing light curtain
vertical Lightand
car gate curtain is especially
an object that isdesigned
NO 30 VDC / 8 A
outputblanking
Auto relay contacts modeGND remain open and min.
1 prevent the
to
in avoid a collision
the closing areabetween a closing
of the gate. Due to vertical car gate
its extremely
5 VDC / 10 mA
door/gate operatingTestin a dangerous 2
way.
and an
compact
NC object
NO
that is in the closing
design, it is possible NC to
area of the gate.
NO install the light
Due Due to the possibility of installingWAGO the2 light curtain
to its extremely compact design, it is possible to install
x 5.08 Permane
curtain edges near the guide profile of the car gate exactly in theOut:closingYellow LED area of the car gate, a much input on “
the lightThe
itself.
COMMON
curtain
wideedges near range
operating the COMMON
guide profileaoflotthe
provides of car higherImportant safety
Power: Green LED
safety level can notes:be achieved compared to
gate
freedomitself.forThe
manywideapplications
operating range provides a lot of
with automatic This test sequence
solutions where the must light be implemented
curtain has to beotherwise installed Operatin
freedom
vertical for many applications with automatic vertical car a safea operation
with small offset cannot to the be carguaranteed!
gateSwitch: panels.
Buzzer on / off However, a
Figure 1:car
Lightgates.
Curtain Function
gates. closing car gate that interruptsJP1 the light beams of the A sensitiv
Please
light curtainreferin to section “Test
a sequential order Input”
from
Potentiometer:
top for more
rangeto down
operating
The Peelle light curtain light curtain is application details.
does not affect the function. The light curtain re-
min. ... max. operating
short ran
especially designed to avoid a collision between a cognizes
Figure 4:the gate diagram
Connection movement control unit and automatically
closing vertical car gate and an object that is Auto
blanks
FIGUREblanking
the2 BLOCK
beams mode that are interrupted by the gate
DIAGRAM
in the closing area of the gate. Due to its extremely itself. Hence, the
compact design, it is possible to install the light DueThe to thecontrol unit light
possibility contains curtain
of installing the differentiates
power
the light supply
curtain
be-
and the
tween the gate and an object that has to be protec-

Switch
curtain edges near the guide profile of the car gate logic inthat
exactly the manages
closing area the sensorof the car edges. gate,A arelay much
ted.provides the status output of the light curtain grid to
itself. The wide operating range provides a lot of higher safety level can be achieved compared to
freedom for many applications with automatic the carwhere
solutions gate the control lightunit.curtain In the has to be installed
vertical car gates. withfollowing
a small sections,
offset to the the car individual
gate panels. elements of the a
However,
whole device are described in
closing car gate that interrupts the light beams of the detail.
Figure1: Typical application The ideal mounting location of the optical edges is in
light curtain in a sequential order from top to down
the Input
guide rails
supply of thevoltagegate. Please refer to Figure 3.
does not affect the function. The light curtain re- Figure 6: S
Features cognizes
The light the curtain
gate movement has a unique anduniversal
automatically power buzzer. Fa
blanks
supply that operates within an input by
the beams that are interrupted the gate
voltage range
x Extremely dense protective field itself. Hence,
between 17the
to 240 lightVolt curtain
AC ordifferentiates
DC. No adjustment be- is Should o
x Installed near the guide rails tween the gateThe
necessary. andpower an object supply thatautomatically
has to be protec- detects sensitivity
x Wide operating range ted.the voltage and adjusts itself for proper function.
x Robust and reliable 1. Ensur
x Sophisticated ASIC technology Output relay poten
x Simple mounting The output relay provides 2. Turn
Figure1: Typical application The ideal mounting location that status
of the of the
optical lightisgrid
edges in until th
x Detachable cables to the gate or door drive control unit.
the guide rails of the gate. Please refer to Figure 3. stop tu
x Virtually no alignment necessary Pleas
Features
x Wide power supply range 17 … 240 VDC Stop OK switch
Main Features of Light Curtain
Installation
x
x Test input 24
Extremely and
VDC
dense Operation
protective field Manual cegard/Max-G32
Figure 3: The light curtain can be installed yellow
x All
•x Self gold-plated
calibrating,
Installed near thecontacts,
fault
guide PCBs and connectors
tolerant
rails directly inside the guide rail illumin
The muting function may be deactivated by remov-
3. Reme
•xBuzzer
Wideinstallation
operating range Test
ingInput
NC
Easy without alignment JP1NOdepending on national
NC NO codes and regula-

tions, i.e. all light beams 4. Now


check are used
The for object detec-
x
• The Robust
Muting and reliable
function
control unit has a buzzer that is active when The safety integrity of Protector clockw
x Sophisticated ASICare technology tion. COMMON COMMON
(described in section Safety Integrity Check) is
• Very densebeams
one or more surveillance interrupted.
area The buzzer can determ
x Simple mounting
be switched on and off with the slide switch located The installer
initiated is fully
by a test input responsible
signal as follows:for complying to
•xbetween
Robust and cables
reliable of the sensor edges.
the connectors
Detachable local
Figurecodes
3: Relay and
outputfor correct installation.
status
•x Integrated
Virtually nodiagnostics
alignment necessary 1. In normal operation, the Test Input has to be set
It is very useful to verify 17 the…installation Inactive mode
x Wide power supply 240 VDC with a to high level. In this mode, the output relay
Applications
turned-on buzzer (page range
4) follows the status of the light
x Test input 24 VDC The protective function maybeams
Figure 3: The light curtain can be installed
as shown in
be deactivated i.e. for
cegard/Max
x is ideal
All gold-plated for more
contacts, PCBs comfort and improved
and connectors Figure
servicing 6. elevator
directly inside the guide rail cars. To deactivate move hand
Jumper JP1 2. slowly
Prior tofromgate/door closing, bottom.
the Test The
Input light
has to
safety on automatic elevator doors and other auto- top towards curtain
matic
Jumperdoors. Complete
JP1 controls kits for modernization,
the auto-blanking function: a be set to deactivated
remains low level. TheforOutput
appr.Relay changes and
10 seconds its the
vast range of accessories or special configurations status beeps.
buzzer to ‘Stop’ as if one or more beams are
are available. Auto
Jumper Comments interrupted. This is the indication that
Position Blanking The Protector is performing an internal safety
Installation
Mode ® check.
cegard/Max must not be used as a protective 3. Due
If thisto internal
the large optical
checkaperture angle (no
and the

226
Set Enabled A moving gate is detec- safety is successful
device for dangerous machinery nor in explo- automatic calibration feature there
failure detected) and no beam is interrupted, theis no alignment
ted and automatically needed as longchanges
as the edges aretowithin
sive atmospheres
THE PEELLEorCOMPANY
radioactive
blanked
environments 2 Output Relay its state ‘OK’ the
so aperture
the
angle.
gate/door drive can close the gate/door. LIGHT CURTAIN
FREIGHT DOORS I CAR
Not set GATES I CAR
Disabled ENCLOSURES
A moving gate is detec- INSTALLATION GUIDE
TECHNICAL SUPPORT 1-800-787-5020
ted like ext
any275other object 4. If the internal safety check detects a failure of
Functional description and triggers the output For installation of opto edges
The Protector meaning that the device pleaselooses
note that,
its safety functionality, the status of the Output
Installation
Assembly (Breakdown)
Assembly
x The sensorx The
edges sensor
mustedges
not be mustbentnotor bebe bent or be
1. Fasten the
1. sensor
Fastenedges the sensorwith 3edgesscrews to a
with 3 flat
screws to a flatexposed to tension.
exposed to tension.
wall or near the
wallguide
or near tracks. The lenses
the guide tracks.ofThe thelenses of the
sensor edges (blackedges
sensor points) mustpoints)
(black face each must face each
other. other.
2. Mount the2. control
Mount unit the withcontrol2 or unit
4 screws
with 2 or to 4a screws to a
stable location
stablenearlocation
the emitter near edge.
the emitterPlease edge. Please
x The sensorx edges
The sensor
have edges
to be aligned
have tobetter
be aligned
than better than
note that thenote
cable thatlength
the cable
of thelength
emitter of (white
the emitter (white
± 10°. ± 10°.
markings) is markings)
5 m only, is whereas
5 m only, the whereas
cable of the cable of the
receiver (bluereceiver
markings) (blue hasmarkings)
a length has of 15a m.length of 15 m.

88
3. Connect 3.
the Connect
cables from the thecables
sensorfromedges
the sensor
to the edges to the
control unit. control
Guide unit.and fix Guidethemand properly
fix them andproperly and
separate them,separate
as farthem,as possible,
as far as from possible,
cables from cables
that carry high
thatvoltages
carry high and/or
voltages
high currents
and/or high in currents in
order to minimize
orderpossible
to minimize EMIpossible
interferences.
EMI interferences.
4. Connect 4.theConnect
control unit the to control
the gate/door
unit to thedrive gate/door drive
unit (Relay Output,
unit (Relay
Test Output,
Input). Test Input).
5. Connect 5.theConnect
protective theground
protectiveterminal
ground of theterminal ofxtheThe cablesxshall
The not
cables
be stretched
shall not be
or squeezed.
stretched or squeezed.
control unit with
control
a lowunitimpedance
with a lowcable impedance
of AWG cable of AWG
x Ensure a xcable
Ensureradius
a cable
R > radius
80 mmR and > 80 avoid
mm and avoid
15 / 1.5 mm2 15or/ 1.5
thicker
mm2 andor athicker
maximum and alengthmaximum length
contaminationcontamination
by oil or greasy
by oil
liquids.
or greasy liquids.
of 200 mm to of a200
protective
mm to a grounded
protective frame
grounded
or a frame or a
protective ground
protective
socket. ground socket.
6. Connect 6.power
Connect

LED
to thepower
indicates thatindicates
on the greenon
it is receiving
the(power).
are free andarethefree
control

green LED
testand
to unit.
that it power
When
input
the control
is receiving
(power).
theistest
The device
by switching-
all lightWhen
on input
unit. The device
power by switching-
beams
“high”,is the
all light beams
on “high”, the
8 8
R R
output relay output
changes relay to changes
the state to“OK” the (relay
state “OK” (relay
output NO) andoutput
the NO)
yellow and LEDthegoes
yellow out.LED goes out.

If there are Ifdifferent


there areLED different
readingsLED than
readings
stated than
in stated in
paragraph 6, paragraph
please go 6, toplease
the gotrouble-shooting
to the trouble-shootingx Please note that thenote
x Please lightthat
curtain
the light
is ancurtain
optical is an optical
section. section. device. Therefore,
device. avoidTherefore,
dust and avoiddirt duston andthe dirt on the
lenses. lenses.
Assembly Notes Assembly Notes x Other infrared
x Other lightinfrared
sourceslight likesources
optoelectronic
like optoelectronic
sensors, flashlights,
sensors,directflashlights,
sun light,
directetc.sun
shall
light,
notetc. shall not
x The cablexoutlets of theoutlets
The cable sensorofedges must be
the sensor at must be shine
edges at directlyshine
into directly
the receiver
into the edge. receiver
They edge.
can They can
the top, as thethegate/door
top, as themust enter the
gate/door protective
must enter the protective the lightwith
interfere withinterfere curtain
the and
light maycurtain
leadand to may lead to
area from theareatop.from the top. instable function.
instableIn such
function.
a case,In such
please a case,
swapplease
the swap the
emitter and the emitter
receiver
and edge,
the receiver
as the edge,
emitterasedge
the emitter edge
is not sensitiveis not
to optical
sensitivedisturbance.
to optical disturbance.
x Fix the control
x Fixunitthe with
control
2 orunit
4 screws
with 2 or in order
4 screws to in order to
avoid vibration.avoid vibration.
x Close thexcoverCloseofthe thecover
controlof unit
the control
in orderunit to in order to
IP65 IP65 IP65 IP65
avoid dust, avoid dirt, humidity,
dust, dirt,and humidity,
liquids and
on the liquids on the
electronic circuits
electronic
and to circuits
avoid andelectrical
to avoidhazards.
electrical hazards.

Connect terminal IP54 IP54


protective earth PE with
E E R R low impedance (< 10 Ω)
to protective earth of the
●● ensure light curtain edges are securely fastened power supply.
CEDES CEDES

●● the cable is well fastened and routed


part No. 104 477 part No. 104 477
17 ... 240 VAC / DC 17 ... 240 VAC / DC

●● avoid obstruction from door wings, cables etc. in Danger of high


Danger
voltage!
of high voltage!
the protective area Disconnect power
Disconnect
beforepower
opening
before
the opening the
cover of the control
cover ofunit!
the control unit!

THE PEELLE COMPANY 3


226
LIGHT CURTAIN
FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
INSTALLATION GUIDE
TECHNICAL SUPPORT 1-800-787-5020 ext 275
Light Curtain #1
Installation Mounting Bracket

Sensor Edge Mounting

Light
Curtain
Sensor
Edge
Tx or Rx

PLAN VIEW
Peelle single section car gate,
right hand rail

Secure light
curtain cables to
using cable ties.

Ensure the
cable clamp
is installed.

Secure light
curtain cables to
using cable ties.

Light Curtain #1
Mounting Bracket

1/4-20 x 1/2”
Hex Bolts, Washers &
B Lock Washers
THIS DRAWING IS THIRD ANGLE PROJECTION
THE CONFIDENTIAL
PROPERTY OF THE
PEELLE COMPANY
AND MAY NOT BE
Light Curtain
COPIED,
REPRODUCED,
UNLESS OTHERWISE SPECIFIE
Sensor Edge
TRANSMITTED OR
DIMENSIONS ARE IN INCHES.
TRANSFERRED IN
ANY MANNER OR REMOVE ALL BURRS & SHARP
FORM, OR USED
FOR ANY PURPOSE TOLERANCES
Use sheetANGLE
WITHOUT THE metal0° ±.1°
FRACTION 0/0
WRITTEN CONSENT ±1/64
screws provided
OF THE PEELLE
1 DECIMAL 0.0 ±.020
COMPANY. 2 DECIMAL 0.00 ±.010
3 DECIMAL 0.000 ±.005
Use a screwdriver to pry out
tab if alignment is necessary

THE PEELLE COMPANY


THIS DRAWING IS
THE CONFIDENTIAL
THIRD ANGLE PROJECTION
4 Freight Elevator Doors Since 1905
® FINISH
226
PROPERTY OF THE LIGHT CURTAIN
FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
PEELLE COMPANY
AND MAY NOT BE
INSTALLATION GUIDE
TECHNICAL SUPPORT 1-800-787-5020 ext 275
COPIED, We still service equipment we built 50 years ago
REPRODUCED,
UNLESS OTHERWISE SPECIFIED
TRANSMITTED OR TITLE REV SCALE SHEET
DIMENSIONS ARE IN INCHES.
TRANSFERRED IN
ANY MANNER OR REMOVE ALL BURRS & SHARP EDGES.
FORM, OR USED
Installation - New Installation (Peelle Car Gates and PLC)

Troubleshooting

EMITTER RECEIVER

POWER

JP1
OUT
min ... max
transmitting
power

Indication  NOTESyellow
green AND EXCEPTIONS:
Action
No function, door open  1.
{ Code {
compliance is theok?
Power supply responsibility
Fuse ok? of the installer.
Gate open, free protective area  2.
z For other
z control interfaces, please contact Peelle
Obstruction?
Troubleshooting engineeringInstallation?
for assistance.
EMC-interference?
Problem Solution Protective earth (PE) connected?
Control unit damaged?
Clean Light Curtain Lenses
Alignment of sensor edges not appropriate?
Dirty sensor edges?
Check to ensure that the Cedes controller is properly
Test input grounded
set to high level?
Semitransparent objects are not  z z Operating range < 3m?
detected Check that the Light Curtain Connection Cables are not running beside High
Sensitivity potentiometer correctly set?
Voltage motor wires
Receiver R problem?    Receiver not connected?
Intermitent Reversal / No Check that the Plugs are securely fastened using the cable clamps provided. ( Do
Receiver damaged?
Function Not tape plugs together )
Receiver cable damaged?
Emitter E problem? Check to ensure
 Receiver
 is notin direct sunlight.
Emitter Swap the transmitter and
not connected?
receiver if the receiver is affected
Emitter damaged?
Emitter cable damaged?
Check to ensure proper alignment. Please see line of site diagram on page 5.
Person or object detected z z Normal operation
If Warning strobe lights are used in close proximity of receiver, relocate light or

No object shield if possible. z { Normal operation
Light Curtains Plugged  & RD wires are connected to the proper relay output contact. RD
Verify that the +24
in
z= / No
LEDReversal
on {/ =
NoLED off  = LED flashing
relay in Peelle controller must be on (no detection) and off for reversal.
Closing

Cleaning of the sensor edges


The edges shall be cleaned with a soft tissue and little soap water only. Any use of abrasive or inappropriate
cleaning solvents may cause loss of range or may damage the device.

THE PEELLE COMPANY 5


226
LIGHT CURTAIN
FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
INSTALLATION GUIDE
TECHNICAL SUPPORT 1-800-787-5020 ext 275
77.4
7 20
0
Light Curtain Edges (pair) IP65 Standard
Ɣ Mounting holes ø 4.5
16
Parameter Specification
Cross-section
ø 4.5 4697 - NEMA1 (IP65) - 13 Ft Range
W ith IP54 Control Unit

CEDES
12

cegardTM/Max 4698 - NEMA1 (IP65) - 24 Ft Range


ø 4.5 Light Curtain W ith IP54 Control Unit
Special configuration M IP67 Dimensions in mm
NO TEST INPUT 4697M - NEMA4 (IP67) - 13 Ft Range
Country code Order No. Position
With IP54 Control unit & IP67 moisture protection kit
Cable outlet
US - 001
C 4698M - NEMA4 (IP67) - 24 Ft Range
To be filled out by customer: (See unit & IP67 moisture protection kit
With IP54 Control
desing guidelines on back side)
1814
Ground screw = 1858 mm

24 No. of light beams 24


Opto edges: Emitter
23 1736 Min. objectReceiver
size to be detected 78 mm at 1900 mm edge
1717 X Emitter and receiver
22 1658 Response time max. 180 ms, typical 90 ms
Element number: 8 Element (34 Beams)
21 1580 Power supply
16 voltage
Element 17 … 240 VAC / DC
(74 Beams)

X consumption
Power 24 Element (114 Beams)
6 VA 115 / 230 VAC, 130 mA / 24 VDC
20 1502
32 Element (154 Beams)
1424 Fuse 6.3 A (slow-to-blow, 250 V, measurement: 5 x 20 mm)
19
Colour of edges: X Black
5 anodized
250 VAC / 8 A, 30 VDC / 8 A (resistive load),
18 1346 Aluminum
Relay output anodizedmin. 5 VDC / 10 mA
RAL Nr. (Extra cost)
1268 Temperature range -20 ... +65°C
17
Other (Extra cost)
45

Vibration and shock resistance IEC 68-2-6


1190
Cover length = 1868 mm

16 Cable length: Emitter 5 m


(Standard 5m, max. 10m)
15 1112
Receiver 5 m
1034 (Standard 5m, max. 30m)
14

Open cover: C= 32 mm (Standard 32mm)


13 956
1900 Control unit: Elevator application (17-240 V AC/DC)
12 878
Elevator application (24 V AC/DC)
847
11 800 Elevator application with test input
Industrial application (17-240 V AC/DC)R
Jumper
10 722
To be filled out by CEDES:
9 644 LED b
Part. No. Configuration
Out z { No.
E
Power z z
Total length of opto edges = 1900 mm

8 566 System 101 893 M0xxx


128

Test +
80

7 488 Transmitter 102 070 M0xxx


max. 30VDC - Connect
protective
NO earth
Output NC
6 410 Receiver 102 071 M0xxx COM
Power 6.3AT P
17..240VAC/DC N
5 332 Control unit max. 5VA

4 254 Manual

3 176
Configured Approved 130
2 98 Date 21.06.2010 176
188
1 20 Signature IBR
200
07
Dimensions in mm

CEDES • Phone +41-81-307-2323 • Fax +41-307-2325 • E-mail:info@cedes.com • www.cedes.com


®

THE PEELLE COMPANY 6


226
LIGHT CURTAIN
FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
INSTALLATION GUIDE
TECHNICAL SUPPORT 1-800-787-5020 ext 275
Maintenance and Inspection
1. Doors and gates shall be maintained in accordance with Peelle Detail Installation and Maintenance
Guide 215 Section 19.
2. Maintenance and inspection of the light curtains system shall be performed on a monthly basis. More
frequent maintenance may be necessary where car gates are subject to demanding environments of
dust, corrosion, moisture, grease, chemical or other conditions.
3. Where necessary, the elevator should be taken out of service for maintenance following proper
procedures by trained maintenance personnel.
4. Refer to Guide 215 Section 19 for gate rail, panel and operating component maintenance.
5. Ensure that each light curtain edge is properly secured to the gate rail according to the installation
instructions.
6. Ensure there is no debris affixed to the car gate panel or rails, for example plastic bags or other rubbish.
7. Check and clean the plastic lens filters on the edges to keep the system in optimum working condition.
8. Where provided, check the gate leading edge rubber astragal for wear or damage and replace if
necessary. Make sure the astragal is properly seated in the holding extrusion.
9. Where pull straps have been provided for manual operation of power operated car gates, the
pull strap should be removed to avoid interfering with the light curtain. If it is desirable to retain
the pull strap, the strap shall be held in position above the leading edge of the car gate. An
electric contact shall be provided that will break the contact, and prevent power operation of the
car gate when the strap is removed from the held position for use. The contact shall be wired
according to the car gate controller manual and wiring diagram.
Note to Maintenance:
The light curtain system represents an important safety device of the elevator and relies on integrity of all
components. Should any part or function of the system be observed not to be in proper order, the elevator
should be taken out of service until such time as the system is repaired.

THE PEELLE COMPANY 7


226
LIGHT CURTAIN
FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
INSTALLATION GUIDE
TECHNICAL SUPPORT 1-800-787-5020 ext 275
®

THE PEELLE COMPANY


FREIGHT DOORS I CAR GATES I CAR ENCLOSURES

TECHNICAL SUPPORT
1-800-787-5020 ext 275
NORTH AMERICAN SALES
sales@peelledoor.com
EXPORT SALES
exportsales@peelledoor.com

You might also like