Professional Documents
Culture Documents
‘ Y ’ STRAINERS
15701.PIP.MEC.SDS
REV. 1
February 1996
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 2
FOREWORD
Rev. n. 0 N° sheets 25
September 1993
Issue
This specification has been restructured from the conceptual and graphical point
of view as “Company specification”; the general revision has been performed in
accordance with the requirements of CEE rules which require to evidence the
functional requirements and the elimination of discriminating elements.
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 3
CONTENT
1 GENERAL
1.1 Scope
2.5 Ergonomics
2.6 Safety
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 4
2.9 Documentation
3 SUPPLEMENTARY ELEMENTS
3.1.1 Annexes
3.1.2 Attachements
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 5
1 GENERAL
1.1 Scope
This specification and the attached Data sheets for “Normalized ‘Y’ strainers”
include also ND 2 strainers with threaded or socked welded ends in accordance
with international Codes.
Company Codes restrict the use of threaded and socked welded ends up to ND
1 1/2.
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 6
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 7
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 8
1.2.3 Legislation
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 9
The criteria used for the identification of ‘Y’ strainers are reported in annex 1.
Inside the specification and individual Data sheets for “Normalized ‘Y’ strainers”
the abbreviation reported in the following paragraphs have been used for
recalling various materials.
The following table reports the materials abbreviations considering the relation
between forged materials and corresponding casting materials.
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 10
The following table reports the abbreviations of materials for bolts and nuts
evidencing their combined use .
PLATES MATERIALS
Abbreviation Designation
AISI 304 ASTM A240 Type 304
AISI 316 ASTM A240 Type 316
AISI 321 ASTM A240 Type 321
AISI 316L ASTM A240 Type 316L
MISCELLANEOUS MATERIALS
Abbreviation Designation
MONEL Alloy corresponding to ASTM B 164
ARMCO ARMCO Steel type, hardness HB ≤90
ALLOY 20 Alloy corresponding to ASTM A 351 Gr. CN 7M
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 11
Individual Data sheet for “Normalized ‘Y’ strainers” should consider the
following factors:
- fluids aggressiveness;
- design temperatureand design pressure;
- constructive features (dimensions, ends, weight, materials);
Strainers fabrication shall be in accordance with the individual Data sheets for
Normalized ‘Y’ strainers.
In addition to what requested in the individual Data sheets for Normalized ‘Y’
strainers, the following requirements shall be applied:
- flanged ends shall be integral with body; only for steel strainers the flanges
may be fitted by means of full penetration butt welding;
- strainers shall have an arrow indicating the flow direction in relief on the
body;
- The foltering elements shall not vibrate or move during the operation; they
shall be easily removable and fabricated using shaped and welded plates with
end edges conveniently reinforced;
- the ratio filtering area (intended as the clear span of filtering element) and
strainer bore, unless otherwise indicated in the Data Sheet “Additional
requirements for ‘Y’ strainers” in other documents issued for the specific
project, shall be equal to:
- for strainers with screwed body-bonnet joint, the body thickness shall be
defined by the Contractor and anyway suitable for the requested pressure
conditions.
For strainers with flanged body-bonnet or pressure-seal joint, the thickness
shall be that one foreseen by API Std 600;
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 12
The nominal diameters indicated in the individual “Data sheets for Normalized
‘Y’ strainers” are correponding to those designated as “Nominal Pipe Size
(inches)” in the ANSI/ASME Codes B16.5.
- ANSI/ASME B16.5 for strainers with steel body and its alloys;
- ASME B16.24 for strainers with bronze body;
- ASME B16.11 for strainers with cast iron body;
The types of joint facing foreseen usually for flanged strainers are:
- FF (flat face): ANSI/ASME B16.1 for strainers with cast iron and
bronze body;
The socket welded ends of strainers (SW) shall be in accordance with ASME
Codes B 16.11.
End to end or face to face indicated in the individual Data sheets for Normalized
‘Y’ strainers have been drawn from codes or Manufacturer’s standards.
Different end to end or face to face from the indicated ones may be accepted
only in case of strainers with threaded or socked welded connections.
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 13
This specification and the Data sheets for Normalized ‘Y’ strainers indicate the
materials requested for fabricating various components. Equivalent materials
may be submitted for Company approval; the proposal shall be justified and
documented, and shall satisfy the chemical analysis and mechanical properties
specified in the above mentioned codes.
2.3.4 Repairs
The Contractor is allowed to repair the bodies strainers only after Company
authorisation; the repairing shall be carried out in accordance with ASME Code
Sect. VIII Div. I appendix 7.
Contractor shall supply a spare parts list for two years operation.
Painting and packing shall be in accordance with the Data Sheet “Additional
requirements for ‘Y’ strainers” and the documents issued for the specific project.
2.3.7 Marking
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 14
Contractor’s name and/or trademark, body material code and nominal diameter
shall be marked on the strainer body (casted or forged).
ADDITIONAL REQUIREMENTS FT
SMOOTH Finish or 125, 250, 500 R a (on flange with RF facing) X
Internal diameter of pipe to be connected X
Supplementary tests X
Tests X
Supplementary tests X
(Ra = aritmetic average of the deviation absolute values measured fromthe center
line of the roughness profile).
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 15
2.5 Ergonomics
2.6 Safety
Flanged or butt welding ends shall be protected with wooden covers having a
diameter not less than the ends.outside diameter.
Screwed or socked welded ends shall be protected with plastic material or
paperboard plugs.
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 16
Strainers and their parts shall be submitted at Contractor care to all tests and
checks foreseen by Inspection Data Sheet (IDS) and particularly:
3) dimensional check;
4) hydraulic test;
Contractor shall notify to the Company, 10 days at least in advance, the set up of
the material to be tested.
The quantity of pieces to be submitted for hydraulic tests (excluding the
supplementary tests) is as follows:
STRAINERS TO BE TESTED
rating Quantity
≤ 800 for ND ≤ 14 Q= N
≤ 800 for ND ≥ 16 100 %
≥ 900 for all ND
where :
Any test with negative result shall require an additional test on a double number
of pieces belonging to the same lot (lot means a group of valves of the same
constructive type, diameter, rating and materials submitted for testing. In
alternative to double testing the Contractor may submit for testing a new lot of
new strainers; finished and unfinished single components of strainers rejected
during the tests inspection may not be used again. The new lot shall be
submitted, after a new heat treatment, to all tests as previously established, not
keeping in account the results of the first testing execution.
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 17
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 18
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 19
The following table reports for each supplementary tests the requested sampling
type.
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 20
P.S.2
N
P.S.3 Q=
2 P
P.S.7 P.S.4 Q= N
P.S.2 Q = 100%
P.S.3 R
P.S.4 Q = N
where :
When the piece shape or the location of the zones to be radiographed do not
allow to get radiographies of clear interpretation a supplementary test P.S.2
shall be carried out.
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 21
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 22
2.9 Documentation
Documentation shall be send to Company for approval and shall include at least:
- top, side, and sectional views, to show overall di mensions and weighs;
- list of inspections, testing, examinations, checks and tests which has been
carried out;
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Sheet 23
3 SUPPLEMENTARY ELEMENTS
3.1.1 Annexes
3.1.2 Attachements
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Annex 1 Sheet 1
Type
Category
Body material group
Rating
Company symbol
Characteristics and materials
Strainer ends
Nominal diameter
type :
FT - "Y" Strainer
category :
0 - cast iron
1 - carbon steel
2 - low alloyed steel
3 - stainless steel
5 - cupper and its alloys (Bronze, Brass, etc.)
7 - metals and special alloys (Hastelloy, Titanium, Monel,
etc.)
8 - non-metallic materials (PVC, Teflon, etc.)
rating:
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1996
Annex 1 Sheet 2
- EXECUTION
- BODY/COVER MATERIAL
- FILTERING ELEMENT MATERIAL
strainers ends:
BW - butt welding
FP - flanged: flat face
GR - flanged: (raised face)
FF - flanged ANSI/ASME: (flat face)
RF - flanged ANSI/ASME: (raised face)
RF 125 R a - flanged ANSI/ASME: RF-125 R a
RF 250 R a - flanged ANSI/ASME: RF-250 R a
RF 500 R a - flanged ANSI/ASME: RF-500 R a
RJ - flanged ANSI/ASME: (ring joint)
THDD - threaded BS/DIN/etc.
NPT - threaded ASME B1.20.1 NPT
SW - socked welded ASME B16.11
SW/THDD - socket welded ends and other threaded ends
nominal diameter:
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
15701.PIP.MEC.SDS
Rev. 1 February 1995
Annex. 2 Sheet 1
The annex reports series of tables with the ‘Y’ strainer used in the Normalized
“Piping design specifications”. The tables are ordered according the
corresponding costructive shapes and materials of body strainer.
The annex allows, considering these characteristics, to find the individual Data
Sheet of Normalized ‘Y’ strainers.
–––––––––––––––––––––––––––––
Il presente documento è RISERVATO ed è di proprietà dell'AGIP. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
FLOW FLOW
P.S.:
- Figures shown are for illustration purpose only.
- Variations in the individual parts are acceptable,
provided that they comply with the Standard
requirements.
RATIO OF FILTERING AREA TO STRAINER BORE 3 : 1 <= 2" - 2 : 1 >= 3" 3 : 1 <= 2" - 2 : 1 >= 3"
BODY MATERIAL
CARBON ASTM A 105 / ASTM A 216 WCB 911AG 2C 913AG 2C 915AG 2C 916AG 3C 917AG 3C
STEEL ASTM A 350 LF2 / ASTM A 352 LCB
OTHER ALLOYS
15701.PIP.MEC.SDS Agip
Internal Normalization "Y" STRAINERS
Issued Approved Date February 1996 FLANGED OR BUTT- WELDING ENDS
Annex 2 Sheet 2 __________ __________ Rev. 1 - SUMMARY -
FLOW
P.S.:
- Figures shown are for illustration purpose only.
- Variations in the individual parts are acceptable,
provided that they comply with the Standard
requirements.
ESECUTION 9.5
RATING 150 800 1500
SIZES RANGES (inches) 1/2÷ 4 1/2 ÷ 2 1/2 ÷ 2
MANUFACTURING CODE
BODY MATERIAL
CARBON ASTM A 105 / ASTM A 216 WCB
STEEL ASTM A 350 LF2 / ASTM A 352 LCB
15701.PIP.MEC.SDS Agip
Internal Normalization "Y" STRAINERS
Issued Approved Date February 1996 THREADED OR SOCKET- WELD OR BUTT-WELDING ENDS
Annex 2 Sheet 3 __________ __________ Rev. 1 - SUMMARY -