Professional Documents
Culture Documents
CATALOGUE
PLATES
Plates
The rolling mill was founded in 1971 and underwent a large modernization in 1999 which facilitated a considerable improvement
of the rolled material geometry, surface quality and expansion of the product mix. Plates are made from concast slabs. Plates are rolled
in the thickness range from 5 to 80 mm, and in the width range from 1,000 to 3,300 mm.
EVRAZ VÍTKOVICE STEEL, a.s. holds the Quality Management System (QMS)
Certificate acc. to EN ISO 9001:2000, API Spec. Q1 and Environmental Management
System Certificate (EMS) acc. to EN ISO 14001:2004.
EVRAZ VÍTKOVICE STEEL, a.s. has also certification of its products according
to the requirements of classification societies and legislation.
2
Contents
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ARMOUR PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
DELIVERY CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
MATERIAL CERTIFICATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MARKING OF PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DIMENSIONAL TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
• Table 1 – Maximum available plates length for steels with minimum tensile strength Rm up to 530 MPa
• Table 2 – Maximum available plates length for steels with minimum tensile strength Rm more than 530 MPa
• Table 3 – Maximum available plates length for thermomechanical rolled plates
3
Plates
Introduction
This catalogue briefly outlines chemical and mechanical properties of commonly used steel plates.
1) All dimensions listed are approximate. Actual plate sizes available depend on the combination of length, width and thickness as well
as on material specification. For particular information, contact EVRAZ VÍTKOVICE STEEL, a.s.
2) Higher thicknesses on agreement
AR – As rolled
N – Normalized
N+T – Normalized and tempered
A – Annealed
M (TMCP) – Thermomechanical rolled
Q+T – Quenched and tempered
4
Plates of structural steels
PLATES OF STEELS ACCORDING TO EN 10025-2
The most commonly used structural steels having minimum yield strength min. 235 MPa and guaranteed weldability that can be used for
low demanding steel structures for bridges, halls, parts of railway and motor vehicles, etc.
1) CEV = C + Mn + Cr + Mo + V + Ni + Cu ; valid for thickness up to 30 mm, for higher thickness refer to the standard
6 5 15
2) Valid for thickness up to 16 mm, for higher thickness refer to the standard
EQUIVALENT DESIGNATION
5
Plates
Structural steels with guaranteed fine-grain structure and low carbon equivalent. Because of the yield strength up to 460 MPa and impact
energy guaranteed at temperature -50 °C these steels are suitable for more demanding steel structures and their supporting elements.
They are suitable for construction of railway and motor vehicles, too.
1) CEV = C + Mn + Cr + Mo + V + Ni + Cu ; valid for thickness up to 63 mm; for higher thickness refer to the standard
6 5 15
2) Valid for thickness up to 16 mm, for higher thickness refer to the standard
EQUIVALENT DESIGNATION
6
Plates of structural steels
THERMOMECHANICAL ROLLED PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10025-4
Thermomechanical rolled plates of structural steels having low carbon equivalent, and thus an excellent weldability. They are used for more
demanding steel structures and their supporting elements. The impact energy is guaranteed also at temperature -50 °C which facilitates
a wide range for their usage.
1) CEV = C + Mn + Cr + Mo + V + Ni + Cu ; valid for thickness up to 63 mm; for higher thickness refer to the standard
6 5 15
2) Valid for thickness up to 16 mm, for higher thickness refer to the standard
3) Higher thickness on agreement
EQUIVALENT DESIGNATION
S275M S275M –
S275ML S275ML –
S355M S355M QStE 380 TM
S355ML S355ML –
S420M S420M QStE 420 TM
S420ML S420ML –
S460M S460M QStE 460 TM
S460ML S460ML –
7
Plates
FINE-GRAIN STEELS
8
Plates of structural steels with improved
atmospheric corrosion resistance (ATMOFIX)
Plates of structural steels with improved atmospheric corrosion resistance do not require – unlike common steels – expensive surface
treatments (painting). They feature increased resistance even against impacts of atmosphere which contains sulphur. Their key use is
in the area of construction and building of bridges but they can be used for chimney/stack and waste gas ducts structures, too.
1) CEV = C + Mn + Cr + Mo + V + Ni + Cu
6 5 15
2) Valid for plates with thickness up to 16 mm, for higher thickness refer to the standard
3) Plates with thickness up to 12 mm only
EQUIVALENT DESIGNATION
S235J0W S235J0W – – –
S235J2W S235J2W – WTSt 37 - 3 –
S355J0WP S355J0WP 15217 – –
S355J2WP S355J2WP – – –
S355J0W S355J0W – – –
S355J2W S355J2G2W 15127 WTSt 52 - 3 350AT
S355K2W S355K2G2W – – –
9
Plates
0.43 2)
42 289 427–565 18/22 -40/27 1
0.45 3)
345 2) 0.43 4)
50 483–620 16/21 -40/34 2
324 3) 0.45 5)
1) CEV = C + Mn + Cr + Mo + V + Ni + Cu
6 5 15
2) For width to 2 1 ⁄ 2“
3) For width over 2 ⁄ 2“ 1
4) For width to 2“
5) For width over 2“
10
Thermomechanical rolled plates
for welded pipes
Thermomechanical rolled plates of non-alloyed and micro-alloyed steels with excellent weldability, designed exclusively for welded pipelines
for combustible and non-combustible fluids. These can be supplied only upon agreement on the basis of Technical Conditions negotiated
between the manufacturer and the customer for supplies of these plates. Technical Conditions must specify all requirements of the customer
for the plates subject to the order.
1) Standards API 5L and EN 10208 are technical conditions for supplies of welded pipes, not for plates
2) Informative values
3) Higher thickness on agreement
API 5L EN 10208-2
B L 245 MB
X 42 L 290 MB
X 52 L 360 MB
X 60 L 415 MB
X 65 L 450 MB
X 70 L 485 MB
11
Plates
Plates of structural steel grades according to the requirements of the inspection companies ABS, BV, DNV, LR, and others, with a yield
strength 235 to 355 MPa, are used for ship and watercraft construction. Quality of this assortment is guaranteed by product approbations
awarded by individual shipping companies.
DNV – Det Norske Veritas
GL – Germanischer Lloyd
PC – Morskoj Registr
LR – Lioyd's Register
BV – Bureau Veritas
Bureau of Shipping
Yield Strength ReH
Impact Energy KV
ABS – American
Sudochodstva
Steel Group
of Shipping
RINA –
[MPa]
Min.
Min.
– A A A A A A A/24 A 1
Normal Strength
Steel Grades
0/27 B B B B B B S/24 B 1
235
-20/27 D D D D D D SS/24 D 1
-40/27 E E E E E E E/24 E 1
0/31 AH 32 AH 32 A 32 A 32 A 32 AH 32 S/32 A 32 1
-40/31 EH 32 EH 32 E 32 E 32 E 32 EH 32 E/32 E 32 1
0/34 AH 36 AH 36 A 36 A 36 A 36 AH 36 S/36 A 36 1
-40/34 EH 36 EH 36 E 36 E 36 E 36 EH 36 E/36 E 36 1
12
Plates for ship building
PLATES ACCORDING TO A 131
13
Plates
Standard methods used for processing these plates are bending, flanging, cold roll forming, etc. Based on agreement these plates can be
delivered in the condition suitable for hot-dip zinc-coating. These plates have excellent weldability because of low carbon equivalent.
EQUIVALENT DESIGNATION
14
Hot-rolled plates for cold forming
NORMALIZED (ROLLED) PLATES OF STEELS ACCORDING TO EN 10149-3
These plates guarantee suitability for cold forming because of their technological processing. Standard methods used for processing
these plates are bending, flanging, cold roll forming, etc. Based on agreement these plates can be delivered in the condition suitable for
hot-dip zinc-coating.
EQUIVALENT DESIGNATION
EN SEW 092
15
Plates
Quenched and tempered plates of 500 Q and 690 Q steel grades are supplied in the form suitable for steel structures (S500 …, S690 …)
as per EN 10025-6 or in the form suitable for pressure vessels (P500…, P690…) as per EN 10028-6.
Designation as per EN 10025-6: S500 Q, S500 QL, S500 QL1, S690 Q, S690 QL, S690 QL1.
Designation as per EN 10028-6: P500 Q, P500 QH, P500 QL1, P500 QL2, P690 Q, P690 QH, P690 QL1, P690 QL2.
Thickness 20–80 mm
Width 1) 1,000–2,500 mm
Length max. 11,000 mm
Weight of one piece of plate max. 8,000 kg
Total volume of plates ordered multiples of 50 t
1) Valid for thickness ≤ 50 mm, for higher thickness refer to the standard
2) On agreement; valid for temperature 300 °C and thickness ≤ 50 mm; for other temperatures (lower)
or higher thickness refer to the standard EN 10028-6
3) For other temperatures (higher) refer to the standard
4) CEV = C + Mn + Cr + Mo + V + Ni + Cu ; only for plates supplied as per EN 10025-6; valid for thickness ≤ 50 mm;
6 5 15
for higher thickness refer to the standard EN 10025-6
16
Plates of non alloy or alloy steels
for quenching and tempering
PLATES OF STEELS ACCORDING TO EN 10083-2 AND EN 10083-3
They are used for machinery parts in all machinery production areas. These plates are difficult for welding in most cases. They are supplied in soft
annealed (+A) or normalized (+N) condition according to the following table. Products of these plates are further processed with heat treatment
(usually quenching and tempering), after such treatment they obtain their typical properties, i.e. high toughness, hardness and strength.
1) Valid for plates in normalized condition and for thickness up to 16 mm, for higher thickness refer to the standard
2) EN 10083-2
3) EN 10083-3
EQUIVALENT DESIGNATION
17
Plates
Dimension Dimension
Grade Grade
Designation table Designation table
(SAE Number) (SAE Number)
number number
1009 1 1006 1
1020 1 1008 1
1035 2 1009 1
A 827
1040 2 1010 1
1045 2 1012 1
1050 2 1015 1
1330 2 1016 1
1335 2 1017 1
1340 2 1018 1
1345 2 1019 1
4118 2 1020 1
4130 2 1021 1
4135 2 1022 1
4137 2 1023 1
4140 2 1025 1
4142 2 1026 1
4145 2 1030 1
4150 2 1033 1
A 829 4615 2 A 830 1035 2
4617 2 1037 2
4620 2 1038 2
8615 2 1039 2
8617 2 1040 2
9620 2 1042 2
8622 2 1043 2
8625 2 1045 2
8627 2 1046 2
8630 2 1049 2
8637 2 1050 2
8640 2 1055 2
8742 2 1060 2
18
Plates with mechanical wear
(abrasive wear) resistance
PLATES OF STEEL ACCORDING TO VN 414320 (ABRAZIT)
Grade 14320 is fine-grain steel which is used for rolling of plates for production of parts exposed to extreme abrasion and mechanical wear.
These plates can be used for transport routes and chutes for gravel, stone, coal, cement etc. Resistance against abrasion, and hardness are
guaranteed either in the condition without heat treatment (so called as rolled – 14320.0), or after quenching.
Machining in the condition without heat treatment (14320.0) is difficult; in the soft annealed condition (14320.3) it is good. Cold forming
is not possible, hot forming at temperature of 850–1,150 °C is good.
Joints between parts are usually made as bolted joints; or in the form of fixing welds, using preheating up to 200 °C at minimum (thickness
up to 10 mm without preheating); however the welded joint does not reach the strength of the parent base. Cutting plates by means
of flame cutting, or flame cutting shaped plates is also performed with preheating up to 200 °C at minimum. Shearing is not recommended
for plate cutting.
These plates can be delivered as semi-trimmed plates having thickness from 8 to 25 mm in the condition without heat treatment (14320.0),
or from 8 to 30 mm in the soft annealed condition (14320.3). Other thickness and dimension on agreement.
Tensile strength (Rm) in the condition without heat treatment (14320.0) is approx. 930 to 1,370 MPa, the lowest yield strength (ReH)
is approx. 75 % of the tensile strength, the lowest elongation (A5) is 8 % and Brinell hardness is approx. 270 to 400 HB. Tensile strength
can be improved to approx. 1,400 MPa by quenching. Tensile strength, yield strength, and elongation are not subject to testing and
acceptance inspections because test samples are difficult to be made.
In the soft annealed condition (14320.3) the Brinell hardness is max. 260 HB.
19
Plates
Plates with low yield strength for simple pressure vessels and storage facilities, e.g. for compressed air or other fluids operating under
normal outdoor temperatures.
Min. Yield Min. Yield Tensile Min. Elongation Min. Impact Dimension
Designation Strength ReH 1) Strength Rp0.2 2) Strength Rm (L0 = 5.65√S0) Energy KV Table No.
[MPa] [MPa] [MPa] [%] [°C/J] – longitudinal
1) Valid for thickness up to 16 mm, for higher thickness refer to the standard
2) Valid for temperature 300 °C, for other temperatures (lower) refer to the standard
20
Plates of steels for pressure vessels
PLATES OF STEELS ACCORDING TO EN 10028-2
Plates of unalloyed as well as alloyed steels for pressure loaded vessels and facilities, operating under normal as well as elevated tempera-
tures. These plates are usually delivered in normalized condition or in normalized and tempered condition.
Min. Yield Min. Yield Tensile Min. Elongation Min. Impact Dimension
Designation Strength ReH 1) Strength Rp0,2 2) Strength Rm (L0 = 5.65√S0) Energy KV 3) Table No.
[MPa] [MPa] [MPa] [%] [°C/J] – transverse
1) Valid for thickness up to 16 mm, for higher thickness refer to the standard
2) On agreement; valid for temperature 300 °C and thickness up to 16 mm; for other temperatures or higher thickness refer to the standard
3) For other temperatures refer to the standard or on agreement
4) Maximum value of the carbon equivalent on agreement when ordering for steels P235GH, P265GH, P295GH and P355GH based
on the following formula C + Mn + Cr + Mo + V + Ni + Cu
6 5 15
EQUIVALENT DESIGNATION
P235 GH 11368 HI
P265 GH 11418 H II
P295 GH 13030 (11478) 17Mn4
P355 GH 11523 19Mn6
16Mo3 15020 15Mo3
13CrMo4-5 15121 13CrMo44
10CrMo9-10 15313 10CrMo910
18MnMo4-5 15223 (15219) –
21
Plates
These steels feature guaranteed fine-grain structure and low carbon equivalent. Mechanical properties of these plates are guaranteed at
high temperatures (up to 400 °C) – yield strength Rp0,2 as well as at low temperatures (down to -50 °C) – impact energy KV; therefore,
they can be used for constructions of more demanding pressure vessels working under high as well as low temperatures.
1) Valid for thickness up to 16 mm, for higher thickness refer to the standard
2) On agreement; valid for temperature 300 °C and thickness up to 16 mm, for other temperatures or higher thickness refer to the standard
3) For other temperatures refer to the standard
4) On agreement; CEV = C + Mn + Cr + Mo + V + Ni + Cu ; valid for thickness up to 60 mm, for higher thickness refer to the standard
6 5 15
EQUIVALENT DESIGNATION
22
Plates of steels for pressure vessels
THERMOMECHANICAL ROLLED PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10028-5
Thermomechanical rolled plates having higher yield strength up to 460 MPa are designed for pressure vessels and facilities working under
normal or low temperatures. These plates have excellent weldability because of low carbon equivalent. Impact energy is guaranteed even
at temperature -50 °C.
1) Valid for thickness up to 40 mm, for higher thickness refer to the standard
2) Valid for thickness up to 16 mm, for higher thickness refer to the standard
3) For other temperatures refer to the standard
4) On agreement; CEV = C + Mn + Cr + Mo + V + Ni + Cu ; valid for thickness up to 16 mm, for higher thickness refer to the standard
6 5 15
5) Higher thickness on agreement
23
Plates
FINE-GRAIN STEELS
24
Armour plates
Plates of armour steels are manufactured in several degrees of hardness, or shooting resistance. Armours of middle hardness are used
mostly for armouring heavy vehicles; armours of high hardness are used for lightweight military vehicles, resistant mainly against infantry
weapons. Armour plates of martenzitic steels can be welded utilizing usually manual arc welding or automatic submerged-arc welding
methods. An advantageous method is shielded welding.
1) approximate values
2) CEV values for information only
25
Plates
Tapered plates are used especially for various types of steel structures where their usage results in consider-
able economical savings (structure weight reduction, reduction of welded joints, etc.)
In order to reach as much economical contribution as possible, and easy application in all steel structures,
various shapes of tapered plates consisting of several tapered and flat segments can be manufactured and
used.
Tapered plates are manufactured of steels according to the standards EN 10025-2 and EN 10025-3.
26
Delivery conditions
APPLICABLE STANDARDS
Automatic ultrasonic TÜV NORD certified line is used or manual testing is available to meet stricter conditions.
27
Plates
Material certificates
QUALITY ASSURANCE CERTIFICATES AS PER EN 10204 : 2004
Quality Assurance certificates shall be issued by the Quality Assurance Department stating chemical composition
of heat and material testing results (e.g. ultrasound, mechanical testing) as required by the customer:
Inspection Companies
a) national: ŘJ, ČD, ZVS, INSPEKTA, ČLPR, and others
b) international: LR, DNV, ABS, BV, GL, TÜV, RINA, Russian Naval Register of Shipping, and others
c) inspection carried out directly by the customer
28
Marking of plates
Product marking is performed by stamping and painting. A punch for stamping in cold condition is used for marking of plates (Four-High
Mill) in low-stress spot method. Manual low-stress stamping (Two-High Mill) the low-stress method has to be agreed in the order. White
paint marking is carried out with automatic marking machines, or manually (usually using templates). In case of any specific customer‘s
requirement for a special plate marking, either in the form of a text (sprayed with white color on the plate), or in the form of color
marking, marking is carried out within the frame of each individual order based on agreement. The “Colour Marking Catalogue” containing
individual patterns is available to make the color marking easier.
Rolled product No. Plate serial No. from the rolled product Manufacturer’s symbol Heat origin Heat No.
Plate
thickness
Steel
grade Heat treatment
code
Rolled product No. Heat origin Heat no. Plate serial No. Plate width
from the rolled product
29
TABLE 1 – MAXIMUM AVAILABLE PLATES LENGTH FOR STEELS WITH MINIMUM TENSILE STRENGTH Rm up to 530 MPa
width [mm] 1,001 1,101 1,251 1,301 1,401 1,501 1,601 1,701 1,801 1,901 2,001
thickness [mm] 1,000 1,100 1,250 1,300 1,400 1,500 1,600 1,700 1,800 1,900 2,000 2,100
5 12 10 10 12 12 12 12 12
6 12 12 12 10 10 10 12 12 12 12 12 12
7 14 14 14 14 14 14 14 14 14 14 14 14
8 15 15 15 15 15 15 15 15 15 15 15 15
9 16 16 16 16 16 16 16 16 16 16 16 16
10 16 16 16 16 16 16 16 16 16 16 16 16
11 16 16 16 16 16 16 16 16 16 16 16 16
12 16 16 16 16 16 16 16 16 16 16 16 16
13 16 16 16 16 16 16 16 16 16 16 16 16
14 16 16 16 16 16 16 16 16 16 16 16 16
15 16 16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 16 16 16
17 16 16 16 16 16 16 16 16 16 16 16 16
18 16 16 16 16 16 16 16 16 16 16 16 16
19 16 16 16 16 16 16 16 16 16 16 16 16
20 16 16 16 16 16 16 16 16 16 16 16 16
21 16 16 16 16 16 16 16 16 16 16 16 16
22 16 16 16 16 16 16 16 16 16 16 16 16
23 16 16 16 16 16 16 16 16 16 16 16 16
24 16 16 16 16 16 16 16 16 16 16 16 16
25 16 16 16 16 16 16 16 16 16 16 16 16
26 16 16 16 16 16 16 16 16 16 16 16 16
28 16 16 16 16 16 16 16 16 16 16 16 16
30 16 16 16 16 16 16 16 16 16 16 16 16
32 16 16 16 16 16 16 16 16 16 16 16 15
34 16 16 15 16 16 16 16 16 16 16 15 14
36 16 16 15 16 16 16 16 16 16 15 14 13
38 16 16 14 16 16 15 16 16 15 14 13 12
40 16 15 13 16 15 14 16 15 14 13 12 12
42 16 14 12 16 14 13 15 14 13 12 12 11
44 15 13 12 15 14 13 14 13 13 12 11 11
46 14 13 11 14 13 12 14 13 12 11 11 10
48 14 12 11 14 13 12 13 12 11 11 10 10
50 13 12 10 13 12 11 12 12 11 10 10 9
52 12 11 10 12 11 11 12 11 10 10 9 9
54 12 11 9 12 11 10 11 11 10 9 9 8
56 11 10 9 11 11 10 11 10 10 9 9 8
58 11 10 9 11 10 9 11 10 9 9 8 8
60 11 10 8 11 10 9 10 9 9 8 8 7
65 10 9 8 10 9 8 9 9 8 8 7 7
70 9 8 7 9 8 8 9 8 7 7 7 6
75 8 7 6 8 8 7 8 7 7 7 6 6
80 8 7 6 8 7 7 7 7 6 6 6 5
10 10 10 10 10 5
12 12 12 12 12 10 10 10 10 6
14 14 14 14 14 13 13 12 12 7
15 15 15 15 15 15 15 15 15 15 8
16 16 16 16 16 16 16 16 16 16 16 16 9
16 16 16 16 16 16 16 16 16 16 16 16 10
16 16 16 16 16 16 16 16 16 16 16 16 11
16 16 16 16 16 16 16 16 16 16 16 16 12
16 16 16 16 16 16 16 16 16 16 16 16 13
16 16 16 16 16 16 16 16 16 16 16 16 14
16 16 16 16 16 16 16 16 16 16 16 16 15
16 16 16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 16 16 17
16 16 16 16 16 16 16 16 16 16 16 16 18
16 16 16 16 16 16 16 16 16 16 16 16 19
16 16 16 16 16 16 16 16 16 16 16 15 20
16 16 16 16 16 16 16 16 16 15 15 14 21
16 16 16 16 16 16 16 16 15 15 14 14 22
16 16 16 16 16 16 16 15 15 14 14 13 23
16 16 16 16 16 16 15 14 14 13 13 13 24
16 16 16 16 15 15 14 14 13 13 12 12 25
16 16 16 15 15 14 14 13 13 12 12 11 26
16 16 15 14 14 13 13 12 12 11 11 11 28
15 15 14 13 13 12 12 11 11 11 10 10 30
14 14 13 12 12 11 11 11 10 10 9 9 32
13 13 12 12 11 11 10 10 9 9 9 9 34
13 12 11 11 10 10 10 9 9 9 8 8 36
12 11 11 10 10 9 9 9 8 8 8 8 38
11 11 10 10 9 9 9 8 8 8 7 7 40
11 10 10 9 9 8 8 8 7 7 7 7 42
10 10 9 9 8 8 8 7 7 7 7 6 44
10 9 9 8 8 8 7 7 7 7 6 6 46
9 9 8 8 8 7 7 7 6 6 6 6 48
9 8 8 8 7 7 7 6 6 6 6 5 50
8 8 8 7 7 7 6 6 6 6 5 5 52
8 8 7 7 7 6 6 6 6 5 5 5 54
8 7 7 7 6 6 6 6 5 5 5 5 56
7 7 7 6 6 6 6 5 5 5 5 5 58
7 7 6 6 6 6 5 5 5 5 5 60
6 6 6 6 5 5 5 5 65
6 6 5 5 5 5 70
5 5 5 5 75
5 5 5 80
TABLE 2 – MAXIMUM AVAILABLE PLATES LENGTH FOR STEELS WITH MINIMUM TENSILE STRENGTH Rm more than 530 MPa
width [mm] 1,001 1,101 1,251 1,301 1,401 1,501 1,601 1,701 1,801 1,901 2,001
thickness [mm] 1,000 1,100 1,250 1,300 1,400 1,500 1,600 1,700 1,800 1,900 2,000 2,100
5 10 10 10 10 10 10 10 10
6 12 12 12 10 10 10 12 12 12 12 12 12
7 12 12 12 14 14 14 14 14 14 14 14 14
8 14 14 14 14 14 14 14 14 14 14 14 14
9 15 16 16 16 16 16 16 16 16 16 16 16
10 16 16 16 16 16 16 16 16 16 16 16 16
11 16 16 16 16 16 16 16 16 16 16 16 16
12 16 16 16 16 16 16 16 16 16 16 16 16
13 16 16 16 16 16 16 16 16 16 16 16 16
14 16 16 16 16 16 16 16 16 16 16 16 16
15 16 16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 16 16 16
17 16 16 16 16 16 16 16 16 16 16 16 16
18 16 16 16 16 16 16 16 16 16 16 16 16
19 16 16 16 16 16 16 16 16 16 16 16 16
20 16 16 16 16 16 16 16 16 16 16 16 16
21 16 16 16 16 16 16 16 16 16 16 16 16
22 16 16 16 16 16 16 16 16 16 16 16 16
23 16 16 16 16 16 16 16 16 16 16 16 16
24 16 16 16 16 16 16 16 16 16 16 16 16
25 16 16 16 16 16 16 16 16 16 16 16 16
26 16 16 16 16 16 16 16 16 16 16 16 16
28 16 16 16 16 16 16 16 16 16 16 16 16
30 16 16 16 16 16 16 16 16 16 16 16 16
32 16 16 16 16 16 16 16 16 16 16 16 15
34 16 16 15 16 16 16 16 16 16 16 15 14
36 16 16 15 16 16 16 16 16 16 15 14 13
38 16 16 14 16 16 15 16 16 15 14 13 12
40 16 15 13 16 15 14 16 15 14 13 12 12
42 16 14 12 16 14 13 15 14 13 12 12 11
44 15 13 12 15 14 13 14 13 13 12 11 11
46 14 13 11 14 13 12 14 13 12 11 11 10
48 14 12 11 14 13 12 13 12 11 11 10 10
50 13 12 10 13 12 11 12 12 11 10 10 9
52 12 11 10 12 11 11 12 11 10 10 9 9
54 12 11 9 12 11 10 11 11 10 9 9 8
56 11 10 9 11 11 10 11 10 10 9 9 8
58 11 10 9 11 10 9 11 10 9 9 8 8
60 11 10 8 11 10 9 10 9 9 8 8 7
65 10 9 8 10 9 8 9 9 8 8 7 7
70 9 8 7 9 8 8 9 8 7 7 7 6
75 8 7 6 8 8 7 8 7 7 7 6 6
80 8 7 6 8 7 7 7 7 6 6 6 5
10 10 10 10 10 5
12 12 12 12 12 10’ 10’ 10’ 10’ 6
14 14 14 12 12 10 10 10 10 7
14 14 14 14 14 13 13 13 13 12 8
16 16 16 14 14 13 13 13 13 12 12 12 9
16 16 16 16 16 16 16 16 16 16 16 16 10
16 16 16 16 16 16 16 16 16 16 16 16 11
16 16 16 16 16 16 16 16 16 16 16 16 12
16 16 16 16 16 16 16 16 16 16 16 16 13
16 16 16 16 16 16 16 16 16 16 16 16 14
16 16 16 16 16 16 16 16 16 16 16 16 15
16 16 16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 16 16 17
16 16 16 16 16 16 16 16 16 16 16 16 18
16 16 16 16 16 16 16 16 16 16 16 16 19
16 16 16 16 16 16 16 16 16 16 16 15 20
16 16 16 16 16 16 16 16 16 15 15 14 21
16 16 16 16 16 16 16 16 15 15 14 14 22
16 16 16 16 16 16 16 15 15 14 14 13 23
16 16 16 16 16 16 15 14 14 13 13 13 24
16 16 16 16 15 15 14 14 13 13 12 12 25
16 16 16 15 15 14 14 13 13 12 12 11 26
16 16 15 14 14 13 13 12 12 11 11 11 28
15 15 14 13 13 12 12 11 11 11 10 10 30
14 14 13 12 12 11 11 11 10 10 9 9 32
13 13 12 12 11 11 10 10 9 9 9 9 34
13 12 11 11 10 10 10 9 9 9 8 8 36
12 11 11 10 10 9 9 9 8 8 8 8 38
11 11 10 10 9 9 9 8 8 8 7 7 40
11 10 10 9 9 8 8 8 7 7 7 7 42
10 10 9 9 8 8 8 7 7 7 7 6 44
10 9 9 8 8 8 7 7 7 7 6 6 46
9 9 8 8 8 7 7 7 6 6 6 6 48
9 8 8 8 7 7 7 6 6 6 6 5 50
8 8 8 7 7 7 6 6 6 6 5 5 52
8 8 7 7 7 6 6 6 6 5 5 5 54
8 7 7 7 6 6 6 6 5 5 5 5 56
7 7 7 6 6 6 6 5 5 5 5 5 58
7 7 6 6 6 6 5 5 5 5 5 60
6 6 6 6 5 5 5 5 65
6 6 5 5 5 5 70
5 5 5 5 75
5 5 5 80
TABLE 3 – MAXIMUM AVAILABLE PLATES LENGTH FOR THERMOMECHANICAL ROLLED PLATES
width [mm] 1,001 1,101 1,251 1,301 1,401 1,501 1,601 1,701 1,801 1,901 2,001
thickness [mm] 1,000 1,100 1,250 1,300 1,400 1,500 1,600 1,700 1,800 1,900 2,000 2,100
8 14 14 14 14 14 14 14 14 14 14 14 14
9 15 16 16 16 16 16 16 16 16 16 16 16
10 16 16 16 16 16 16 16 16 16 16 16 16
11 16 16 16 16 16 16 16 16 16 16 16 16
12 16 16 16 16 16 16 16 16 16 16 16 16
13 16 16 16 16 16 16 16 16 16 16 16 16
14 16 16 16 16 16 16 16 16 16 16 16 16
15 16 16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 16 16 16
17 16 16 16 16 16 16 16 16 16 16 16 16
18 16 16 16 16 16 16 16 16 16 16 16 16
19 16 16 16 16 16 16 16 16 16 16 16 16
20 16 16 16 16 16 16 16 16 16 16 16 16
21 16 16 16 16 16 16 16 16 16 16 16 16
22 16 16 16 16 16 16 16 16 16 16 16 16
23 16 16 16 16 16 16 16 16 16 16 16 16
24 16 16 16 16 16 16 16 16 16 16 16 16
25 16 16 16 16 16 16 16 16 16 16 16 16
26 16 16 16 16 16 16 16 16 16 16 16 16
28 16 16 16 16 16 16 16 16 16 16 16 16
30 16 16 16 16 16 16 16 16 16 16 16 16
32 16 16 16 16 16 16 16 16 16 16 16 15
34 16 16 15 16 16 16 16 16 16 16 15 14
36 16 16 15 16 16 16 16 16 16 15 14 13
38 16 16 14 16 16 15 16 16 15 14 13 12
40 16 15 13 16 15 14 16 15 14 13 12 12
14 14 14 14 14 8
16 16 16 14 14 9
16 16 16 16 16 16 16 10
16 16 16 16 16 16 16 11
16 16 16 16 16 16 16 12
16 16 16 16 16 16 16 13
16 16 16 16 16 16 16 16 16 14
16 16 16 16 16 16 16 16 16 15
16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 17
16 16 16 16 16 16 16 16 16 18
16 16 16 16 16 16 16 16 16 19
16 16 16 16 16 16 16 16 16 20
16 16 16 16 16 16 16 16 16 21
16 16 16 16 16 16 16 16 15 22
16 16 16 16 16 16 16 15 15 23
16 16 16 16 16 16 15 14 14 24
16 16 16 16 15 15 14 14 13 25
16 16 16 15 15 14 14 13 13 26
16 16 15 14 14 13 13 12 12 28
15 15 14 13 13 12 12 11 11 30
14 14 13 12 12 11 11 11 10 32
13 13 12 12 11 11 10 10 9 34
13 12 11 11 10 10 10 9 9 36
12 11 11 10 10 9 9 9 8 38
11 11 10 10 9 9 9 8 8 40
EVRAZ VÍTKOVICE STEEL, a. s.
Headquarters: Štramberská 2871/47, 709 00 Ostrava-Hulváky, Czech Republic
Postal address: EVRAZ VÍTKOVICE STEEL, a. s., 706 02 Ostrava-Vítkovice, Czech Republic
Phone: +420 595 952 435, Fax: +420 595 952 144
E-mail: tradesteel@cz.evraz.com