Professional Documents
Culture Documents
Website http://biz.lgservice.com
SERVICE MANUAL
Mini Hi-Fi System
SERVICE MANUAL
1-1
SECTION 1
SUMMARY
CONTENTS
1-2
SERVICING PRECAUTIONS
NOTES REGARDING HANDLING OF THE PICK-UP
1. Notes for transport and storage
1) The pick-up should always be left in its conductive bag until immediately prior to use.
2) The pick-up should never be subjected to external pressure or impact.
2. Repair notes
1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials.
2) The pick-up should always be handled correctly and carefully, taking care to avoid external pressure and
impact. If it is subjected to strong pressure or impact, the result may be an operational malfunction and/or
damage to the printed-circuit board.
3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reason
the adjustment point and installation screws should absolutely never be touched.
4) Laser beams may damage the eyes!
Absolutely never permit laser beams to enter the eyes!
Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.
Pressure
Magnet
Pressure
Conductive Sheet
6) Never attempt to disassemble the pick-up.
Spring has excess pressure. If the lens is extremely dirty, apply isopropyl alcohol to the cotton swab.
(Do not use any other liquid cleaners, because they will damage the lens.) Take care not to use too much
of this alcohol on the swab, and do not allow the alcohol to get inside the pick-up.
1-3
NOTES REGARDING COMPACT DISC PLAYER REPAIRS
1. Preparations
1) Compact disc players incorporate a great many ICs as well as the pick-up (laser diode). These components
are sensitive to, and easily affected by, static electricity. If such static electricity is high voltage, components
can be damaged, and for that reason components should be handled with care.
2) The pick-up is composed of many optical components and other high-precision components. Care must be
taken, therefore, to avoid repair or storage where the temperature or humidity is high, where strong magnet-
ism is present, or where there is excessive dust.
2. Notes for repair
1) Before replacing a component part, first disconnect the power supply lead wire from the unit
2) All equipment, measuring instruments and tools must be grounded.
3) The workbench should be covered with a conductive sheet and grounded.
When removing the laser pick-up from its conductive bag, do not place the pick-up on the bag. (This is
because there is the possibility of damage by static electricity.)
4) To prevent AC leakage, the metal part of the soldering iron should be grounded.
5) Workers should be grounded by an armband (1 MΩ)
6) Care should be taken not to permit the laser pick-up to come in contact with clothing, in order to prevent stat-
ic electricity changes in the clothing to escape from the armband.
7) The laser beam from the pick-up should NEVER be directly facing the eyes or bare skin.
Armband
Resistor
(1 MΩ)
Resistor
Conductive
(1 MΩ)
Sheet
1-4
ESD PRECAUTIONS
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated
circuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive surface
such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can
generate electrical charges sufficient to damage ESD devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD
devices.
6. Do not remove a replacement ESD device from its protective package until immediately before you are
ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive materials).
7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the
protective material to the chassis or circuit assembly into which the device will by installed.
CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER
SAFETY PRECAUTIONS.
8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate
static electricity sufficient to damage an ESD device).
1-5
HIDDEN KEY MODE
Push both Front key and RCU key to activate it for 5 seconds.
3. Clear EEPROM
Front Key : STOP
RCU Key : SKIP-
4. Edit EEPROM
Front Key : STOP
RCU Key : SKIP+
You can change the digit of option by SKIP+/-.
You can edit 0~f by REPEAT or PLAY/PAUSE key.
5. Bluetooth DUT
Front Key : STOP
RCU Key : PROGRAM
Bluetooth model only
1-6
SERVICE INFORMATION FOR EEPROM
POWER ON
NAME HEX
OP0 05
FLD ‘OP-0…. OP1 00
OP2 00
OP3 00
OP4 00
Move to appropriate position and OP5 69
make changes with remote control. OP6 80
( , , /■ , REPEAT ) OP7 45
OP8 00
OP9 01
Remote control ‘ ’ +
Front ‘STOP’ push same timing.
Completed
1-7
PROGRAM UPGRADE GUIDE
1. Check the download file name.
4. VFD Display
1) MICOM : “WRITE XX”
2) Mpeg(DSP) : “FIRMWARE”
3) EQ : “EQ DOWN”
4) DEMO : “FIRMWARE”
5. Complete Update
1) When the Set is turned off automatically after display "UPDATED", remove the USB storage.
2) Unplugged the power cord after display "FINISHED", then remove the USB storage.
1-8
SPECIFICATIONS
• GENERAL
Power requirements Refer to the main label.
Power consumption Refer to the main label.
Dimensions (W x H x D) 285 x 398 x 357mm
Net Weight (Approx.) 8.2 kg
Operating temperature 5 °C to 35 °C (41 °F to 95 °F)
Operating humidity 5 % to 90 %
Bus Power Supply USB DC 5 V 500 mA
• INPUTS
Auxiliary Input 2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
Microphone Input 6.3 mm jack
Portable Input 1.2 Vrms (3.5 mm stereo jack)
• TUNER
FM Tuning Range 87.5 to 108.0 MHz or 87.50 to 108.00 MHz
AM Tuning Range 522 to 1 620 kHz, 520 to 1 720 kHz or 522 to 1 710 kHz
• CD
Frequency Response 40 to 20 000 Hz
Signal-to-noise ratio 75 dB
Dynamic range 80 dB
• AMPLIFIER
Stereo mode 420 W x 2 (THD 20 %)
Surround mode Front 420 W x 2 (THD 20 %)
Surround 210 W x 2 (THD 20 %)
Subwoofer 420 W x 2 (THD 20 %)
• FRONT SPEAKER
Type 2 Way 2 speaker
Impedance 6Ω
Rated Input Power 420 W
Max. Input power 840 W
Net Dimensions (W x H x D) 263 x 445 x 357 mm
Net Weight 8.6 kg
• SUBWOOFER
Type 1 way 1 speaker
Impedance 6Ω
Rated Input Power 420 W
Max. Input power 840 W
Net Dimensions (W x H x D) 456 x 602 x 453 mm
Net Weight 20.8 kg
1-9
MEMO
1-10
SECTION 2
CABINET & MAIN CHASSIS
CONTENTS
2-1
MEMO
2-2
EXPLODED VIEWS
1. CABINET AND MAIN FRAME SECTION (CM9530)
NOTES) THE EXCLAMATION POINT WITHIN AN
EQUILATERAL TRIANGLE IS INTENDED
268 443 TO ALERT THE SERVICE PERSONNEL
TO THE PRESENCE OF IMPORTANT
SAFETY INFORMATION IN SERVICE
443 LITERATURE.
443
A43 VFD
443
C
CABLE3 443
CABLE1
G
CABLE4 L
443
A53
H
B/T
MIC
A42
254
Portable 270
443 SMPS
A47 A
443 B
F
CABLE2 267
M 443
252 M
E D
443 443
269
443 C K
D 443
E
VOLUME
K
A54
F MAIN
G
251
A46
259
B A
252
L 300
253 443 266
A44
272
271
MEMO
2. MECHANISM DECK SECTION (DP17TM)
1439
1002
A001
1005 1001
1024
1437
1030
1437
1024
1024
1012
1049
1013 1016 1437
1015
1024
1020
1011
A006
1019
1043
1018 A005
1045
1439
3. PACKING ACCESSORY SECTION
803 Packing
804 Bag
803 Packing
802 Box
4. SPEAKER SECTION
4-1. FRONT SPEAKER (NS9530F)
A60
A61A
653
651
653
652
4-2. SUBWOOFER SPEAKER (NS9530W)
• LEFT SUBWOOFER
A90L
A91A
953
951
953
952
SUBWOOFER SPEAKER (NS9530W)
• RIGHT SUBWOOFER
A90R
A91A
953
951
953
952
2-10
SECTION 3 ELECTRICAL
CONTENTS
ONE POINT REPAIR GUIDE ............................................................................................................................ 3-2
1. NO POWER ............................................................................................................................................ 3-2
2. NO BOOTING WHEN POWER ON THE SET ....................................................................................... 3-4
3. VFD IS NOT DISPLAYED WHEN POWER ON THE SET..................................................................... 3-5
4. NO BOOTING IN CD/USB FUNCTION .................................................................................................. 3-6
5. NO OPERATION OF MD ..................................................................................................................... 3-10
6. NO SOUND .......................................................................................................................................... 3-15
7. AUDIO OUTPUT IS SMALL OR NO AUDIO OUTPUT ........................................................................ 3-22
8. NO POWER ON (STANDBY LED IS BLINKING) ................................................................................ 3-23
9. SPEAKER NO AUDIO .......................................................................................................................... 3-24
3-1
ONE POINT REPAIR GUIDE
1. NO POWER
If the unit doesn’t work by no power problem, repair the set according to the following
guide.
[^WmVY\W}hj [^WmVY\W}hj
{o`WW
mo`WX m`WX
mo`WY
X Y \
y`WX y`WY y`WZ
y`W[ y`W\ y`W]
Xt
Y X
Xt
ZZWmVY^\}hj
XU\t
ZZWmVY^\}hj
y`WW
muyTX[r]_X{
{XYhsVY\W}
H
{o`WX
j`WX
nwZ`WTWYwT{z
{wX\
{wXZ
OXYhGY\W}P
[
jt`WX
X
}y`WW
jt`WY
]WW}VXWh
\
Xt
wu`WX
Xt
{o`WY X Y
{X\hsVY\W}
{wX]
mvytw
{wX[
Y
[ Z ik`WX X
ylhk
j`WY
{zXWr]WTWX
Xt
Xt
Y
Z
[
s m` W Y
Y\X\
oz`W]
Y _ o
sm`WX
H
H
nuk
j`WZ
nuk
XWWWmVY\W}hj
j`W`
XWWWmVY\W}hj
j`W]
Xm V\\W}
< F901 > < BD901 > < TH900 ~ TH902 >
If F901 is not short-circuit, If BD901 is short-circuit, If TH900 ~ TH902 is open,
replace it with a same replace it with a new one. replace it with a new one.
specifications one.
3-2
ONE POINT REPAIR GUIDE
NO POWER
If the unit doesn’t work by no ±PVDD problem, repair the set according to the follow-
ing guide.
wj`WZ
oz`W\GoVz
Y\TeZZW {o`XZ
{o`XY ^WTeYUY wUnuk
Y
wmj{o
in w{msW[inYYYxYu\XhWOinP
thyranY
mo`XY
m`XX nuk
X Y
wmjv|{ Y X
Z_W}
XWYwm
XWYwm
mo`XX
j`^`
]UZhVY\W}
j`^_
oz`W[
\WX\
wUnuk
wUnuk H
Z
Y
[
{`WZ YW
ylhk
j`^Y
Y X`
wUnuk
ij`XX Yk
y`_] {w[]
Z X_
XWW Xn
j`Z\ {w[_y``Z Zz
ylhk
k`XY
[^Wm ZUZ
y`__{w]W k`ZY
x`W\ [ X^
y``W
XWr
ztmiX[
[U^
k`Z\
V\W} ztmiX[
pwh]WyX`Wl]
\ X]
{w[Y y``Y wUnuk
{w[Z
{`WY
ZUZ jt`^YWGw|szl
X\
XW
]
^
]
ztmiX[
k`Z[
~X
~Z
vuVvmmaXXUZ¥XYU^}
y`h]
~Y
Xt
{w]Y ^ X[
i_[TjX]
wUnuk
YYm V\W}
_
^
]
\
XZ
nuk
on
y`[\
}jj
sn
_
XWm
Xt
j`ZZ
k`W[
j`ZY
{w]Z pjlXozWXnTX
pj`WY
XY
y`[[
}jzsaWU_}
Xt
}jzoaXU]Z}
{w][ mioa[U\}Gv}lysvhk XX
mtpu X
Yk
jz Y
mi Z
}puz [
}aXUY\}
Xn
Xt
XWW
{w]\ wUnuk k`Y] Zz Y_{a_{
ylhk
y`i_ {w]X
k`X^
YZWoa\Zo
{w[X y`[` [U^
x`W]
y`i`
ztmiX[
XWr
pwh]WyX`Wl]
y`[Y
Xt
YY
}puzGaY_\} {wZ` j`Z[
XL
y`\W
XWr
i_[TjXW
XWWm
ylhk
YYm
j`[Z
k`X[
y`[X
j`[W
Y[r
[^m VY\}
{wZ_
WUWZZmVXWWW}
j`[Y
k`X\
wUnuk
y`\X
XYr
XWm
j`^^
XWWm
uj
j`Z`
ylhk
ylhk
y`Y^
ylhk
y`h_
XzzZ\\
y`_W
Xr}
[^
X~
H
y`\X aY[rde]\ro k`YX j`_Y
3-3
ONE POINT REPAIR GUIDE
2. NO BOOTING WHEN POWER ON THE SET
The set doesn’t work when press the power button on the front board or the remote
control.
X100
(32.768 kHz)
X101
IC101
(12 MHz) KEY1
(Pin15)
< MAIN board top view >
3-4
ONE POINT REPAIR GUIDE
3. VFD IS NOT DISPLAYED WHEN POWER ON THE SET
When power on the set, any icons or characters on VFD are not displayed.
737373
3-5
ONE POINT REPAIR GUIDE
4. NO BOOTING IN CD/USB FUNCTION
After you turn on power key and displayed message in the following order
(HELLO --> VOL XX --> CD or USB) on VFD,
it will not display other message on VFD, and it will not boot-up normally.
,&
'
3-6
ONE POINT REPAIR GUIDE
NO BOOTING IN CD/USB FUNCTION
After you turn on power key and displayed message in the following order
(HELLO --> VOL XX --> CD or USB) on VFD,
it will not display other message on VFD, and it will not boot-up normally.
,&
X500
;
3-7
ONE POINT REPAIR GUIDE
NO BOOTING IN CD/USB FUNCTION
After you turn on power key and displayed message in the following order
(HELLO --> VOL XX --> CD or USB) on VFD,
it will not display other message on VFD, and it will not boot-up normally.
VCC
CS#
CLK
DO
3-8
ONE POINT REPAIR GUIDE
NO BOOTING IN CD/USB FUNCTION
After you turn on power key and displayed message in the following order
(HELLO --> VOL XX --> CD or USB) on VFD,
it will not display other message on VFD, and it will not boot-up normally.
} jj
y
V jz
y hz
V~l
jhz
3-9
ONE POINT REPAIR GUIDE
5. NO OPERATION OF MD
When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the servo motors in MD don’t work. This step is for checking the
SPINDLE MOTOR among them.
63
63
zwR
zwT
< Waveform of SP- & SP+ < Signal check point >
for driving SPINDLE motor >
3-10
ONE POINT REPAIR GUIDE
NO OPERATION OF MD
When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the servo motors in MD don’t work. This step is for checking the
SLED MOTOR among them.
zsR 6/
6/
zsT
< Waveform of SLED- & SLED+ < Signal check point >
for driving SLED motor >
3-11
ONE POINT REPAIR GUIDE
NO OPERATION OF MD
When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the servo motors in MD don’t work. This step is for checking the
TRAY OPEN/CLOSE MOTOR among them.
svT
svROylkP
tv{vwlu
tv{jsvzl
< Waveform
for driving TRAY open / close motor >
/2 /2
027B23(1 027B23(1
SLQRI,& SLQRI,&
3-12
ONE POINT REPAIR GUIDE
NO OPERATION OF MD
When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the pickup module in MD doesn’t work. This step is for checking the
LASER TRACKING ACTUATOR.
7
SLQRI&1
{T Gju[W[
{RGGju[W[
7
SLQRI&1
< Waveform of T±
for driving TRACKING actuator >
3-13
ONE POINT REPAIR GUIDE
NO OPERATION OF MD
When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the pickup module in MD doesn’t work. This step is for checking the
LASER FOCUSING ACTUATOR.
)
SLQRI&1
mRGGju[W[
mT Gju[W[
)
SLQRI&1
3-14
ONE POINT REPAIR GUIDE
6. NO SOUND
There is no sound output in the CD FUNCTION, repair the set according to the follow-
ing guide.
< I2S Signal Flow > < Waveform of I2S audio interface signals >
LRCK / BCK / DATA(IC501 Pin83, 84, 85)
3-15
ONE POINT REPAIR GUIDE
NO SOUND
There is no sound output in the USB FUNCTION, repair the set according to the fol-
lowing guide.
< USB function signal flow > < Waveform of USB D± signal >
USB D+ / D- (CN502 Pin5, 6 & 8, 9)
3-16
ONE POINT REPAIR GUIDE
NO SOUND
There is no sound output in the AUX FUNCTION, repair the set according to the fol-
lowing guide.
$8;B5WR5
AUX_L/R
IC202 AUX
CS5346
$8;B/WR5
DAC_MCLK ADC_DATA
IC501 DAC_BCK
DAC_LRCK
IC600
MLC3700 TAS5548 IR AMP
$'&0,&B'$7$WR
5
IRS2092+IRF6775
PWM
0&6B%&.WR5
0&6B/5&.WR5
0&6B0&/.WR5
< AUX function signal flow > < Signal check point >
3-17
ONE POINT REPAIR GUIDE
NO SOUND
There is no sound output in the PORT. IN FUNCTION, repair the set according to the
following guide.
POT. IN 37%B5WR5
{T POT_L/R
IC202 MIC/PTB
CS5346 Board 37%B/WR5
DAC_MCLK ADC_DATA
IC501 DAC_BCK
DAC_LRCK
IC600 IR AMP $'&0,&B'$7$WR
MLC3700 TAS5548 IRS2092+IRF6775 5
PWM
0&6B%&.WR5
0&6B/5&.WR5
0&6B0&/.WR5
< PORT. IN function signal flow > < Signal check point >
3-18
ONE POINT REPAIR GUIDE
NO SOUND
There is no sound output in the TUNER FUNCTION, repair the set according to the
following guide.
TUNER 781(5B5WR&
{T TUNER_L/R
IC202
CS5346 781(5B5WR&
DAC_MCLK ADC_DATA
IC501 DAC_BCK
DAC_LRCK
IC600 IR AMP $'&0,&B'$7$WR
MLC3700 TAS5548 IRS2092+IRF6775 5
PWM
0&6B%&.WR5
0&6B/5&.WR5
0&6B0&/.WR5
< TUNER function signal flow > < Signal check point >
3-19
ONE POINT REPAIR GUIDE
NO SOUND
There is no sound output in the MIC IN FUNCTION, repair the set according to the
following guide.
0,&B,1387
MIC IN
MIG_SIG IC506 Y
IC202 MIC
CS5346 S4308 Board
DAC_MCLK MIC_I_DATA
IC501 DAC_BCK
DAC_LRCK
IC600 IR AMP
MLC3700 TAS5548 IRS2092+IRF6775
PWM
0,&B287387
< Signal check point >
< MIC IN function signal flow >
3-20
ONE POINT REPAIR GUIDE
NO SOUND
There is no sound output in the BLUETOOTH FUNCTION, repair the set according to
the following guide.
B/T Module
BT_RX,
BT_TX
IC501 IC600
MLC3700 TAS5548
PWM
DAC_BCK
DAC_LRCK
DAC_DATA
IR AMP
IRS2092+IRF6775 %WB5;5
%WB7;5
%WB5765
3-21
ONE POINT REPAIR GUIDE
7. AUDIO OUTPUT IS SMALL OR NO AUDIO OUTPUT
Audio signal output is small or not. when you power on the Middle Power Mini
System.
3-22
ONE POINT REPAIR GUIDE
8. NO POWER ON (STANDBY LED IS BLINKING)
It doesn’t turn on, and blinks standby LED(Red).
3-23
ONE POINT REPAIR GUIDE
9. SPEAKER NO AUDIO
Speaker No Audio
9-1. AMP IC
9-1-1. Solution
Please check and replace the component on MAIN board.
&1
%9
3*1'
%9
3-24
ELECTRICAL TROUBLESHOOTING GUIDE
1. POWER SUPPLY ON SMPS BOARD
No output 5.6 VA
NO
F901 normal? Replace F901 (same fuse).
YES
NO
BD901 normal? Replace BD901.
YES
Is the VCC NO
(11 V ~ 25 V) supplied to IC901 D960, D961 normal?
Pin4?
YES
No 12 V
Is the NO
VCC 12 VA supplied to IC951 Check or replace D965.
Pin1?
YES
Is there NO
‘H’ signal at IC951 Check P_CTL from μ-com.
Pin4?
YES
3-25
ELECTRICAL TROUBLESHOOTING GUIDE
No -5 V
Is the NO NO
VCC -7 VA supplied to IC953 D959 normal? Check or replace D959.
Pin2?
YES YES
Is there NO
‘H’ signal at Q953 Check P_CTL from μ-com.
Base?
YES
No output VFD
NO
R968 normal? Replace R968.
YES
NO
D957, D958 normal? Replace D957, D958.
YES
NO
ZD951, ZD952 normal? Replace ZD951, ZD952.
YES
3-26
ELECTRICAL TROUBLESHOOTING GUIDE
Is the VCC NO NO
13 VA supplied to IC952 R952 normal? Check or replace R952.
Pin1 to Pin3?
YES YES
3-27
ELECTRICAL TROUBLESHOOTING GUIDE
No AMP output
Is the NO NO
C904 voltage PFC P.CTL OK? Check PFC P.CTL from μ-com.
about 380 V?
YES YES
Is the NO
VCC 12 V supplied to Replace D908, Q955, PC903.
IC904 Pin16?
YES
Check or replace
IC904, Q907 ~ Q910.
NO YES
Is the NO
Replace F911. VCC 12 V supplied to Replace D908, Q956, PC902.
IC902 Pin8?
NO
YES
Q905, Q906 OK?
NO
3-28
ELECTRICAL TROUBLESHOOTING GUIDE
2. SYSTEM PART
Power on.
“HELLO” NO CN105 NO
Display on FLD cable connection Check 25p FFC cable.
OK? OK?
YES YES
CN301
NO
Pin13, 19, 20, 22 Check SMPS board.
power OK?
YES
CN301
NO
Pin14~17 data signal Check MAIN board.
OK?
YES
Replace DIG301.
YES YES
Replace LED
(LD351 ~ LD366).
YES YES
3-29
ELECTRICAL TROUBLESHOOTING GUIDE
3. NO AUDIO PART
CD FUNCTION
YES
YES YES
Check IC501.
Is motor impedance NO
Check Loading motor.
about 12 Ω?
Check IC408.
NO
YES YES
YES YES
IC501 NO
Pin95,96,97 I2S input Check IC501.
signal OK?
YES
3-30
ELECTRICAL TROUBLESHOOTING GUIDE
USB play
IC501 NO
Pin16, 18 USB_HUB_D output Check IC501.
signal OK?
YES
YES YES
AUX
IC202 NO
Pin23,24 AUX input signal Check audio cable.
OK?
YES
IC202 NO
Pin42,43,44 I2S input signal Check IC501.
OK?
YES
IC202 NO
Pin41 ADC data output signal Replace IC202.
OK?
YES
3-31
ELECTRICAL TROUBLESHOOTING GUIDE
POT. IN
IC202 NO
Pin9,10 POT. IN input signal Check MIC board.
OK?
YES
IC202 NO
Pin42,43,44 I2S input signal Check IC501.
OK?
YES
IC202 NO
Pin41 ADC data output signal Replace IC202.
OK?
YES
TUNER
IC202 NO TU101 NO
Pin23,24 TUNER_L/R input TUNER_L/R output Check +3.3 V of TU101.
signal OK? signal OK?
YES YES
IC202 NO
Pin42,43,44 I2S input Check IC501.
signal OK?
YES
IC202 NO
Pin41 ADC data output Replace IC202.
signal OK?
YES
3-32
ELECTRICAL TROUBLESHOOTING GUIDE
IC501 NO
Pin82, 83, 84 I2S data output Check IC501.
signal OK?
YES
IC501 NO
pin 85 I2S data signal Check IC501.
OK?
YES
IC600 NO
PWM data output signal Replace IC600.
OK?
YES
IC600 NO
Pin38,39,40,41,44,45,46,47,48,49
(FR,FL,RR,RL,SW1±) Check IC600.
signal OK?
YES
IC206, NO
IC207,IC208 audio signal Check IC206,IC207,IC208.
OK?
YES
Pin13 of NO
IC700 ~ IC705 Audio signal Check IC700 ~ IC705.
OK?
YES
±62 V, -50 V, NO
-28 V, ±5 V power voltage Check SMPS.
OK?
YES
Q705 ~ Q708, NO
Q711 ~ Q718 Check Q705 ~ Q708, Q711 ~ Q718.
OK?
YES
YES
OK
3-33
ELECTRICAL TROUBLESHOOTING GUIDE
4. NO LIGHTING (FRONT/ WOOFER SPEAKER)
CN100 ~ CN103 NO
Pin6,7 I2C signal OK? Check IC501.
YES
CN100 ~ CN103 NO
Check SMPS board.
Pin1,2 +12 V OK?
YES
CN100 ~ CN103 NO NO
Check IC204. Replace IC204.
Pin3 5V OK?
YES YES
3-34
WAVEFORMS OF MAJOR CHECK POINT
1. WAVEFORM OF SERVO
2
3
4
5
3-35
2. WAVEFORM OF MOTOR DRIVE
SL+
8
SP+ 9
6 SL-
7
SP-
00
Figure 2-1. SP- & SP+ for driving SPINDLE motor Figure 2-2. SL- & SL+ for driving SPINDLE motor
(IC408 Pin17, 18) (IC408 Pin11, 12)
10 LO-
MOT_OPEN
11 LO+(RED)
MOT_CLOSE
3-36
3. WAVEFORM OF AUDIO SIGNAL
12 AUDIO_L
LRCK
13 BCK
DATA
14
AUDIO_R
15 MCK
16 LRCK
18 D+
17 BCK
19 D-
3-37
6. WAVEFORM OF CRYSTAL 7. WAVEFORM OF VFD GRID CURRENT DRIVER
20 XI
22
CH1:R327(TP304)
23 CH2:Q301 Emitter
21 XO
3-38
WIRING DIAGRAM
(#0
670'4 5RGCMGT6GTOKPCN
8%% 52- 52- 52- 52-
/QFWNG .KIJV .KIJV .KIJV .KIJV
2
((%2OO
$ğFKP*CT
2 2OO #9)%6;2'
P/UP #WZLCEM
((%%QP2
#&%
9CHGT2
MOT AMP AMP AMP
%&&52
+4#/2$.1%-
XGk ljrGG
t ljohupzt 4(
5'481
((%%QP2
75$&6[RG*CT 2 OO
((%2OO
/+%1/
29/
%#$.'2#9)
((%2OO
&6[RG((%2OO
%6[RG((%2OO $ğFKP*CT
R
/#+02%$ BT VFD
2#9)&6;2'
%#$.'2#9)
((%2OO
%#$.'2#9) 8(&2%$
$VQ$RKP
*CTPGUU2
*CT2 OO
((%2OO
6TCPU
6TCPU
6TCPU
6TCPU
USB1 USB2
&6[RG*CT2 OO
*CTPGUU
((% 8QNWOG2%$ 8QNWOG2%$
5/252%$ *CTPGUU2
3-39 3-40
BLOCK DIAGRAMS
1. SMPS BLOCK DIAGRAM
Ǹ 8(&
/#+05/25 8 8--
+%
Ǹ
564#& 8 (.
(N[DCEM
/#+0 8 12#/2
9FF 64#05
WEQO$6
2(%1WV Ǹ
8# 75$/2')
2(%+%
8 /QVQT&KTXG
Ǹ
4## ('6 8 (#0.'&/KE
6QVGO #
RQNG 8 1P1HH
+PVGTNGCXGF
'# 2(%
&%/ )CVG
1P1HH
2%64.
&TKXG
1P1HH
#/2
#%.KPG 1P1HH Ǹ Ǹ 2%64.
(KNVGT$NQEM
8CTKUVQT 9FF 4A.
:%CR
.KPG(KNVGT 4A4
6JGTOKUVQT
*CNH )#6'
*CNH$TKFIG (A.
..%
('6 $TKFIG &KIKVCN
2WNUG #
4GUQPCPV+% 6TCPU 8
..%
28&& 2QYGT
+%'*5) '# 64#05
8
#/2 (A4
)CVG
#/2
&TKXG 28&& 59A.
#%
8
59A4
%*9
3-41 3-42
2. MAIN SYSTEM BLOCK DIAGRAM
Ucom Interface
A,B,C,D,E,F,PD
8A4(
8A%&
8
16.9344MHz
USB1 USB2
8%% LD BU9543KV
SPDO/SLDO/FOD/TRD RF+ SERVO
P/UP
CD_DIN_DOUT
CD_MCK/BCK
BUSY,CD_16M
,
/LRCK/DATA
CD_R/W,
SUBSYQ,
CD_RST
8A75$
USB2512
LOADs,SLEDs,
8 USB HUB
SPINs,TRs,Fs
M
S3053 MOT_MUTE,CLOSE,OPEN USB_HUB_DP/DN
Motor Drive
8A%&8%%
OP_SW,CL_SW,UP_SW,DN_SW,D_SE NSE MIC_SIG0 MIC_DET
A/+%
k ljrGG /+%%1&'% MIC_SIG
t ljohupzt S4308 MIC
8A%&
'# --> '# 128Mbit
SDRAM MLC3700
MCS LOGIC
8
8A%&
8A%&
DAC_MCLK
8A#&%
/BCK/LRCK
4MByte
8MByte
Serial Flash ADC_DATA PT_L/R
Serial Flash CS5346 Portable
(for Demo sound) #&%%1&'%
AUX_L/R
CD_DVD_CE/ AUX
CLK/DO/RST
TUNER_L/R
8
9.8304MHz
8A7%1/ CD_DVD_DI TUNER
PWM_MCK/BCK/ CLK/DAT/CE/RST/GPO2
32.768KHz MIC_O_DATA0
LRCK
AGL_F/R
FRONT VFD_STB/CLK/DO/RS T
STANDBY_LED,VOL_LED1~7
12.288MHz
8
8(& USB_PWR_CTRL FL· FL FL
DAC IC FL
&+) KEY1~3,JOG_A/B RL· RL RL
AZ4580 RL
VOL_A/B,EXP_CLK/D AT
S_DJ_1/2,REMOCON
+4
MICOM FR· FR DRIVER FR FET
4GEGKXGT I2C/EXT_MUTE/RST TAS5548 DAC IC FR
EXP_DAT1/CLK1~2 LC87F085 RR· RR IRS2092 IRF6775
PWM AZ4580
(x 6EA) RR (x 12EA) RR
8QNWOG E2PROM_CLK/DATA
-G[ SW DAC IC SW SW1
8A7%1/ SPENA SW1
AZ4580 SW2
SW2
EEPROM
AMP_OSC
3-43 3-44
3. MAIN POWER BLOCK DIAGRAM
39V 51mA
} rr
4.4V 300mA } mk
ms G·
RXY} mh uVzwrGslkOmS~PSzwlhuhStpjGhtwOz[ZW_P
3.7V ??A
h XXX^ioThkq h ^WY^Gylzl{
pj XW[ Tj vt
l lwyvt
h ^WY^Gw zluz
3.7V
h XXX^ioThkq z {TiGslk
??A
pj yt jGy
3.3V
R\U]} h i|`\[Zr}
0.6A t sjZ^WW
s t Y`X\YyzThkq h XXX^ioTXUYGOpj\W`P z kyht
pj \W\ z mshzo
j z \Z[]
iV {Gt
5V 1A |z iY\XYi
s t Z^XWYkGO pjZP x2EA
{|uly
5V 36mA
s t Z^XWYkThkqGO pj^W^P pyzYW`Y w z `_\[
5V 550mA h [\_W i|YW`W
s t Z^XWYkThkqGO pjYW[P
z ZW\Z
T\} w pjrT|w
TiRXY} pyzYW`Y
Ti
pym]^^\t
Ri
3-45 3-46
IMPORTANT SAFETY
12
11
10
Warning
Parts that are shaded are critical with
respect to risk of fire or electrical shock.
CAUTION:
1 Danger if fuse is incorrectly replaced.
Replace only with the type identical to fuse rating SMPS #1
and(or) model name described in main label. EAX65026601_9.1.9_SMPS_SD_1
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-47 3-48
2. SMPS - POWER #2 CIRCUIT DIAGRAM
12
11
10
Warning
1 Parts that are shaded are critical with
respect to risk of fire or electrical shock. SMPS #2
EAX65026601_9.1.9_SMPS_SD_2
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-49 3-50
3. MAIN - MICOM CIRCUIT DIAGRAM
12
11
10
1
MAIN - MICOM
EAX64910902_2.1.0_MAIN&_SD_1
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-51 3-52
4. MAIN - CD DSP CIRCUIT DIAGRAM
12
11
10
20
21
19
18
2
13 12 14
1
: WAVEFORM NUMBER MAIN - CD DSP
EAX64910902_2.1.0_MAIN&_SD_2
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-53 3-54
5. MAIN - SERVO CIRCUIT DIAGRAM
12
11 2
3
5
10
6 1
5
4
3
11
10
8
2 9
6 7
1
: WAVEFORM NUMBER MAIN - SERVO
EAX64910902_2.1.0_MAIN&_SD_3
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-55 3-56
6. MAIN - ADC/ PWM CIRCUIT DIAGRAM
12
11
10
15 16 17
1
: WAVEFORM NUMBER MAIN - ADC/PWM
EAX64910902_2.1.0_MAIN&_SD_4
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-57 3-58
7. MAIN - AMP CIRCUIT DIAGRAM
12
11
10
1
MAIN - AMP
EAX64910902_2.1.0_MAIN&_SD_5
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-59 3-60
8. VOLUME CIRCUIT DIAGRAM
12
11
10
1
VOLUME
EAX65025101_5.1.4_Volume_SD
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-61 3-62
9. VFD CIRCUIT DIAGRAM
12
11
10
23
22
8
1
: WAVEFORM NUMBER VFD
EAX64911002_0.1.0_VFD_SD
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-63 3-64
10. MIC CIRCUIT DIAGRAM
12
11
10
1
MIC
EAX64986002_0.1.0_MIC_SD
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-65 3-66
11. PORTABLE CIRCUIT DIAGRAM
12
11
10
1
PORTABLE
EAX65072302_0.1.0_Portable_SD
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-67 3-68
12. FRONT SPEAKER LED - DRIVER CIRCUIT DIAGRAM
12
11
10
1
F-SPK LED-DRIVER
EAX65032202_0.1.0_F.SPK.LED.Driver_SD
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-69 3-70
13. FRONT SPEAKER LED - SUB CIRCUIT DIAGRAM
12
11
10
1
F-SPK LED-SUB
EAX65032302_0.1.0_F.SPK.LED.Sub_SD
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-71 3-72
14. WOOFER SPEAKER LED - DRIVER CIRCUIT DIAGRAM
12
11
10
1
W-SPK LED-DRIVER
EAX64935302_0.1.0_W.SPK.LED.Driver_SD
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-73 3-74
15. WOOFER SPEAKER LED - SUB CIRCUIT DIAGRAM
12
11
10
1
W-SPK LED-SUB
EAX64986102_0.1.0_W.SPK.LED.Sub_SD
2013. 01. 17
A B C D E F G H I J K L M N O P Q R S T
3-75 3-76
CIRCUIT VOLTAGE CHART MEMO
100V-10% 240V/50Hz+10%
Location No. Value Capacitor (uF) Voltage_Spec.
Measured voltage Measured voltage
SMPS Board
C904 330uF 450V 380V 380V
C911 100uF 50V 12.5V 12.8V
C930 68uF 450V 138V 336V
C932 22uF 50V 14V 14.5V
C936 1000uF 16V 5.65V 5.68V
C947 100uF 50V 31.2V 31.5V
C956 470uF 16V 5.1V 5.08V
C957 100uF 16V -5V -5V
C958 100uF 16V 12V 12V
C964 220uF 25V 11.99V 11.98V
C966 2200uF 80V 62V 62V
C968 2200uF 80V 62V 62V
3-77 3-78
PRINTED CIRCUIT BOARD DIAGRAMS
1. SMPS P.C.BOARD
(TOP VIEW)
3-79 3-80
SMPS P.C.BOARD NOTE) Warning
(BOTTOM VIEW) Parts that are critical with respect to risk
of fire or electrical shock.
3-81 3-82
2. MAIN P.C.BOARD
(TOP VIEW)
3-83 3-84
MAIN P.C.BOARD
(BOTTOM VIEW)
3-85 3-86
3. VOLUME P.C.BOARD
(TOP VIEW)
3-87 3-88
VOLUME P.C.BOARD
(BOTTOM VIEW)
3-89 3-90
4. VFD P.C.BOARD
(TOP VIEW)
(BOTTOM VIEW)
3-91 3-92
5. MIC P.C.BOARD
(TOP VIEW) (BOTTOM VIEW)
6. PORTABLE P.C.BOARD
(TOP VIEW) (BOTTOM VIEW)
3-93 3-94
7. FRONT SPEAKER LED - DRIVER P.C.BOARD
(TOP VIEW) (BOTTOM VIEW)
3-95 3-96
9. WOOFER SPEAKER LED - DRIVER P.C.BOARD
(TOP VIEW) (BOTTOM VIEW)
3-97 3-98