You are on page 1of 1

Universal isolate transducer

MODEL TW-4M-1-N, TW-4M-4-N


W !
NE
1. Setting or changing input range
SW1 SW2
on
0 to 5 V off
on
0 to 10 V off
on
0 to 60 mV off
on
1 to 5 V off
on
-5 to 5 V off
on
-10 to 10 V off
on
 Input Specification 0 to 20 mA off
on
Input Input resistance Input allowable range 4 to 20 mA off
0 to 5 VDC 1 2 3 4 1 2 3 4 5 6 7 8
2. Setting Speed 3. Setting Revers (Output)
0 to 10 VDC
SW2 SW2
0 to 60 mVDC on on
More than 1 MΩ 50 mS off MORMAL off
1 to 5 VDC
-50 to +150% F.S on on
-5 to 5 VDC 500 mS off
REVERS off
-10 to 10 VDC 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

0 to 20 mADC 4. Setting or changing output range


250 Ω
4 to 20 mADC SW3 SW3
on on
0 to 5 V off -10 to 10 V off
 Output Specification 0 to 10 V
on
off 0 to 20 mA off
on

on
Output Load resistance 1 to 5 V off 4 to 20 mA on
off
0 to 5 VDC on 1 2 3 4 5 6 7 8
1 to 5 VDC More than 2 KΩ -5 to 5 V off
1 2 3 4 5 6 7 8
-5 to 5 VDC
0 to 10 VDC
-10 to 10 VDC
More than 4 KΩ  Ordering Code
TW – 4M – –N
0 to 20 mADC 1. 100 to 240 VAC ±10%
Less than 550 Ω Code to
4 to 20 mADC specify power 4. 24 VDC ±10%

 General Specifications  Dimensions


1. Range settings before shipment: Side view 41 Front view
17.4 48
Input; 1 to 5 VDC, output; 4 to 20 mADC
Accuracy of range settings before shipment:
Within ±0.25% F.S
2. Error caused by input range setting change: Within ±1% F.S
Error caused by output range setting change: Within ±1% F.S

Sliding from 96 to 98
I/O range
3. Temperature characteristic: ±0.02% F.S/°C setting
4. Response time: Less than 50ms (Time required for arriving Dip SWs.
at 90% of rated output) ZERO/SPAN
35.4

35.2

64.5
94

adjusters
5. Insulation resistance: Between input and output or power supply,
More than 100 MΩ (At 500 VDC) I/O range
setting
6. Dielectric strength: Between input and output or power supply, Dip SWs.
For 1 min. (At 2000 VAC)
7. Power supply voltage: 100 to 240 VAC ±10% or 24 VDC ±10%
Consuming current:
Less than 50mA (At 100 VAC) 20
Less than 80mA (At 24 VDC) 4.5
8. Operating ambient temperature: -5 to +50°C
9. Operating humidity: Less than 90% RH (No dew-condensing)
 Connection Diagram
10. Storage temperature: -10 to +70°C -
Power
- Power
4 8 100-240VAC
11. Storage humidity: Less than 60% RH (No dew-condensing) Input
signal 50 / 60Hz 24VDC
12. Case material: Black PBT 94-V0
+ 3 7 50mA + 80mA
13. Weight: Approx. 130g 15V
MAX TW-4M
About solderless terminal to connect with 30mA
2 6 -
the screw type terminal block Output 18V
Signal 30mA
MAX
1.Screw size: M3.5×7L 1 5 +
2.Recommendation solderless terminal: Ring tongue (R type) M3.5
Spade tongue (A type) M3.5 ! Note : When conducting wiring, be careful with its polarity.
Applicable Wire AWG# 26 to22
3.Quality of material: Screw Iron, nickel plating
Connection board  Block Diagram
Yellow copper, tin plating
Isolation Amp ZERO SPAN
 Setting or changing input/output range 3(+) Input 5(+)
! Always set or change the input/output range with the power turned off. Input signal
circuit Output Output signal
4(-) circuit
The input/output range can be set or changed by dip switches SW1 6(-)
and SW2, SW3 on top of the transducer.
Power circuit

7(~), (+)
After finishing the setting, stick the attached seal to the window for dip Power
switch operation. Prior to factory shipment, the input is set 1 to 5 V 8(~), (-)
and the output, 4 to 20 mA.
SW1 SW2 SW3
Range settings on
before shipment off

Watanabe Electric Industry Co.,Ltd

You might also like