Professional Documents
Culture Documents
TESTING MANUAL
TASK 71-21-00-213-801-B
EFFECTIVITY: ALL
ENGINE FORWARD MOUNT ASSEMBLY - INTERNAL
1. General
A. This task gives the procedure to do a detailed inspection of the engine-forward-mount assembly. The
inspection is applicable to the yoke, links, clevises, lugs and attachment hardware, and the LH/RH
internal sides of the nacelle.
HARD COPY IS UNCONTROLLED. ONCE PRINTED, THIS PAGE MUST NOT BE RETAINED FOR FUTURE REFERENCE.
D. Structural Significant Item(s): 71-21-001 - ENGINE FORWARD MOUNT ASSEMBLY.
2. References
BEFORE USING, MAKE SURE THIS HARD COPY IS THE LATEST ISSUE.
REFERENCE DESIGNATION
AMM TASK 06-43-00-800-801-A/100 Powerplant and Pylon Access Doors and Panels
Aircraft Maintenance Safety Procedures - Standard Proce-
AMM TASK 20-00-00-910-801-A/200
dures
Connection of the external AC power supply to the aircraft -
AMM TASK 24-42-02-860-801-A/200
Aircraft/System Configuration
Disconnection of the external AC power supply from the air-
AMM TASK 24-42-02-860-802-A/200
craft - Aircraft/System Configuration
AMM TASK 52-46-00-000-801-A/400 Middle Avionics-Compartment Access-Door - Removal
AMM TASK 52-46-00-400-801-A/400 Middle Avionics-Compartment Access-Door - Installation
AMM TASK 71-11-00-910-801-A/200 Fan Cowl - Open
AMM TASK 78-33-01-040-801-A/200 Isolation Control Unit (ICU) - Deactivation
AMM TASK 78-33-01-440-801-A/200 Isolation Control Unit (ICU) - Reactivation
AMM SDS 34-61-00/1 FLIGHT MANAGEMENT SYSTEM
ZONES
LOCATION REFERENCE
ACCESS
REFERENCE DESIGNATION
HARD COPY IS UNCONTROLLED. ONCE PRINTED, THIS PAGE MUST NOT BE RETAINED FOR FUTURE REFERENCE.
MCDU
TYPE DESIGNATION LOCATION BUS LOCATION TIP
PAGE
BEFORE USING, MAKE SURE THIS HARD COPY IS THE LATEST ISSUE.
CB E2 REVERSER RICC DC BUS 2 - -
DC ESS BUS EN-
SSPC E2 START VLV SPDA2 SPDA2-M5
2 GINE
CB SLAT ACE 1 LHCBP DC BUS 1 FLIGHT CONTROLS -
DC ESS BUS
CB SLAT ACE 2 RHCBP FLIGHT CONTROLS -
2
6. Job Set-Up
WARNING: MAKE SURE THAT THE AIRCRAFT IS IN A SAFE CONDITION BEFORE YOU DO THE
MAINTENANCE PROCEDURES. THIS IS TO PREVENT INJURY TO PERSONS AND/OR
DAMAGE TO THE EQUIPMENT.
WARNING: MAKE SURE THAT THE FLIGHT-CONTROL SAFETY LOCKS AND THE WARNING
NOTICES ARE IN POSITION. THIS IS TO PREVENT AN ACCIDENTAL COMMAND OF THE
FLIGHT CONTROL SURFACES AND INJURY TO PERSONS.
A. Do the procedure to make the aircraft safe for maintenance (AMM TASK 20-00-00-910-801-A/200).
B. Connect the external AC power supply to the aircraft (AMM TASK 24-42-02-860-801-A/200).
Filtered Serial Nº contained in this publication: 178
C. Open these circuit breakers and put a circuit breaker ring and tag (inoperative - do not operate) on
each one of them:
D. On the MCDU (AMM SDS 34-61-00/1), use the sequence in parentheses to open these SSPCs:
(2) Open and remove access door 147AL (AMM TASK 52-46-00-000-801-A/400).
F. Open these circuit breakers and put a circuit breaker ring and tag (inoperative - do not operate) on
each one of them:
HARD COPY IS UNCONTROLLED. ONCE PRINTED, THIS PAGE MUST NOT BE RETAINED FOR FUTURE REFERENCE.
H. Use a workstand (engine and pylon) to get access to the area that you will examine.
I. Open these access doors (AMM TASK 06-43-00-800-801-A/100 and AMM TASK 71-11-00-910-801-A/
200) to get access to the area where you will do the inspection:
• 412AR
BEFORE USING, MAKE SURE THIS HARD COPY IS THE LATEST ISSUE.
• 413AL
• 422AR
• 423AL
J. Before you do the inspection, clean the area with a lint-free wiper cloth soaked in water.
7. Procedure (Figure 1)
B. Use a 10X magnifying lens to do the detailed inspection of the engine-forward-mount assembly. The
inspection is applicable to the yoke, links, clevises, lug and attachment hardware, and the LH/RH
internal sides of the nacelle. Make sure that:
• There are no nicks, scratches, gouges, dents, corrosion and other signs of damage;
8. Indication Evaluation
A. Close these access doors (AMM TASK 06-43-00-800-801-A/100 and AMM TASK 71-11-00-910-801-A/
200) to get access to the area where you will do the inspection:
• 412AR
• 413AL
• 422AR
• 423AL
B. Remove the workstand (engine and pylon) and all tools, equipment and unwanted materials from the
worked area.
D. Remove the circuit breaker ring and tag (inoperative - do not operate) from each of these circuit
breakers and close them:
HARD COPY IS UNCONTROLLED. ONCE PRINTED, THIS PAGE MUST NOT BE RETAINED FOR FUTURE REFERENCE.
• E1 REVERSER-LICC (DC BUS 1)
BEFORE USING, MAKE SURE THIS HARD COPY IS THE LATEST ISSUE.
(1) Install and close access door 147AL (AMM TASK 52-46-00-400-801-A/400).
F. On the MCDU (AMM SDS 34-61-00/1), use the sequence in parentheses to close these SSPCs:
G. Remove the circuit breaker ring and tag (inoperative - do not operate) from each one of these circuit
breakers and close them:
H. Disconnect the external AC power supply from the aircraft (AMM TASK 24-42-02-860-802-A/200).
EFFECTIVITY: ALL
Engine-Forward-MountAssembly - Inspection
Figure 1
HARD COPY IS UNCONTROLLED. ONCE PRINTED, THIS PAGE MUST NOT BE RETAINED FOR FUTURE REFERENCE.
B
A
BEFORE USING, MAKE SURE THIS HARD COPY IS THE LATEST ISSUE.
ZONES
416
426
A
ENGINE FWD
MOUNT ASSEMBLY
SSI 71−21−001
SWING LINK
CLEVIS
FAIL−SAFE LUG
NK170NDT710010D.DGN
B CLEVIS
LEGEND: SWING LINK
INSPECTION AREA.