Professional Documents
Culture Documents
Uses
Cicol NT Slurry produces an abrasion resistant, non-slip, Tensile strength, permanent strain after rupture and elastic
wearing course. The system may be applied to prepared modulus as function of temperature at a thickness of
concrete, steel or wooden substrates. Cicol NT Slurry resin is approximately 5 mm (In accordance to ASTM D 638, load
dressed with selected hard wearing aggregates. speed:3 mm/minutes):
o o
The thickness is 5 - 8 mm, depending on use and the type of Properties +20 C -20 C
dressing material selected which in turn provides the anti-skid
properties. Tensile strength at 22.2 64.0
2
break (MN/m ):
Applications include bridge decks, RO/RO link-spans, parking
areas, garages, ramps, walkways and cycle paths. Permanent strain after 16.0 3.8
rupture (%)
Advantages Elastic modulus 1350 2850
2
(MN/m )
Coaltar free - friendly to the environment.
Page 1
Cicol NT Slurry
amplitude of at least 100 micro-metre is required. The slurry Cicol NT Slurry is now ready for use.
must be applied immediately after blasting the steel.
Timber Under no circumstances can either thinners or solvents be
added.
The surface should be clean, dry and uncontaminated.
Hardwoods may require abrasion in order to obtain a good Mix proportions by weight (50 kg packs):
mechanical key. Cicol NT Slurry is applied without the need
of a primer.et 5-05 Mix ratio, A : B : C : 20.6 : 7.9 : 71.5, bw.
The prepared substrate should be primed with one even Heavy traffic 4.0 - 4.75 mm 7.2 - 8.6 kg
coat of Nitoprime 31DK at a rate of approx. 0.2 litre/m².
Nitoprime 31DK is a solvent-free, 2-component primer. The Table 1. These thickness exclude the subsequent dressing
primer must be mixed in below mentioned proportions by of the surface with aggregate.
weight (12.5 liters packs):
The mixed Cicol NT Slurry must be applied within the pot
Mix ratio, A : B : 2 : 1, bw. life (30 minutes at +20°C) of the material. It is
recommended that 100 mm wide self adhesive tape is
Comp. A (base) : 9.06 kg applied at the edges of the area to be treated.
Comp. B (hardener) : 4.53 kg Pour the slurry onto the prepared surface. Apply in lanes of
approximately 2-3 metre widths. The slurry is spread evenly
The entire contents of the hardener can (Comp. B) should be over the area with a steel trowel or squeegee. Care must be
poured into the base can (Comp. A) and the two materials taken to ensure that where the material is applied against
mixed thoroughly for at least one minute. The use of a heavy- existing Cicol NT Slurry, there is total contact, at a similar
duty, slow-speed, flameproof or air driven drill fitted with a thickness. It is essential that a wet film thickness gauge be
suitable mixing paddle is desirable. used to ensure an even thickness is achieved.
When mixed, the primer should be applied immediately with a The selected aggregate dressing, see Table 2, must be
stiff brush in a thin continuous film. Care should be taken to applied immediately after application of the slurry. The
avoid over application or puddles. slurry has to be dressed until obliterated and no slurry is
visible. The dressing is applied by methods that will ensure
Pot life for Nitoprime 31DK : 25 minutes at +20°C. that it falls vertically down onto the slurry. If hand-thrown,
there will be ridges created that cannot be remedied later.
The Cicol NT Slurry is applied “wet-on-wet”, normally before
1 hour at +20°C. Before the slurry cures, remove the adhesive border tape.
Table 2. The dressing aggregate depends on traffic type and traffic density.
Technical support
Cleaning
Precautions
Storage
Shelf life
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
www.fosroc.com Khamis Mushayt Tel: (07) 250 0469 Fax: (07) 250 0469 CSD Tel: (02) 608 0999 Fax: (02) 638 0693
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 3 FO SA/CICOL NT SLURRY/05/B