Professional Documents
Culture Documents
VAS 5052
This booklet describes a new diagnostic tool which performs the tasks
as a successor model, and complements the Vehicle Diagnostic, Testing and Information System VAS 5051.
In addition, it is capable of offering further functions in the field of displaying Service Information (ELSA).
The new diagnostic tool thus offers compatibility with predecessor models and a familiar, clearly arranged operation.
The diagnostic tool has been developed particularly for mobile use as a second or third unit and can also be used in
the workshop as a workpad.
NEW Important
Note
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
- Diagnostic tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
- Mechanical design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
- Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Operating Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
- Vehicle self-diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
- Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
- Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3
At a Glance
Administration
It makes it possible to perform various tasks in
Print Help
IrDA + -
V.A.G 1551
7
C
8
0
9
Q - document fault entries, measured values and test
procedures in the form of a hardcopy.
256_006
4
What are the reasons for a new
diagnostic system?
As electronic systems increasingly evolve and on- The necessary interfaces are provided for
board systems are increasingly interlinked and accessing service information available on local
networked, this gives rise to a wide range of servers or for accessing Internet data.
changed tasks in the vehicle service and fault
finding sectors. A Scan Tool mode permits the data transfer with
The fault reader V.A.G 1551 is no longer able to control units which have an influence on exhaust
fully satisfy these requirements and therefore emissions, of all vehicle manufacturers, as is
must be replaced by a successor unit. mandatory as part of the On-Board Diagnosis
(OBD) concept.
A first step in being able to satisfy these changed
service requirements, was undertaken with the It is also possible to display on the screen of the
introduction of the Vehicle Diagnostic, Testing diagnostic tool a wide range of service
and Information System VAS 5051. This information, such as maintenance table, current
diagnostic tool for the first time offered the flow diagrams, workshop manuals etc. from the
operating modes of „Guided fault finding“ and „ELSA“ system.
„Test instruments“, which in the meantime have
been shown to be useful aids in fault-finding All the required information is available directly
electronic on-board systems. at the vehicle and is always as up-to-date as
possible.
The new Vehicle Diagnostic and Service
Information System VAS 5052, will be a The two Diagnostic Systems VAS 5051 and
replacement for the previous fault readers while VAS 5052 form the basic equipment for all
at the same time complementing the support workshops of the Volkswagen Group by virtue of
concept for modern electronic vehicle systems. their modern technology and future-oriented
capabilities.
This diagnostic tool is a complete solution
comprising hardware and software and includes
all the necessary diagnostic and service
information.
It performs tasks within the sector of vehicle
servicing, such as interrogating the fault
memories of all the control units, update
programming of control units or resetting service
interval displays.
5
At a Glance
– interrogating the contents of fault memories – use as workpad in the workshop process, in
of all the control units in a vehicle particular in combination with the Electronic
Service Information System (ELSA)
– performing service routines via the diagnostic
interfaces, such as resetting the service inter- – directly integrated into training concepts as a
val display, adapting new vehicle keys, deac- result of the multimedia capability of the unit
tivating or activating front passenger/side
airbags
6
VAS 5052
Vehicle Diagnosis and Service Information System
Version -GB- / V01.02 20/08/2001
Vehicle
Self-diagnosis
WO R KS H O P
EQUIPMENT ElsaWin
Applications
Administration
Print Help
IrDA + -
VAS 5052
256_027
– mobile diagnostic tool for servicing vehicles – infrared interface for linking to an external
with electronic systems printer
– for use as a stand-alone unit or in the – integrated DVD drive for CD-ROM with
Client-Server version (refer to p. 29) repair information and multimedia
applications in the specific language
– an integral rechargeable battery enables the
tester to be operated without mains supply for – software updating by means of CD-ROM or
short periods (charger is integrated) on-line
– identical user interface as VAS 5051 in the – display for Electronic Service Information
„Vehicle Self-Diagnosis“ operating mode System (ELSA), electronic workpad
– diagnosis communication possible with all – Scan Tool for On-Board Diagnosis (OBD)
(present and future) vehicles of the VW
Group – standard interfaces for future applications,
e. g. Telediagnosis, Wireless LAN (wireless
local area network)
7
Design and Interfaces
Diagnostic tool
1 2
Front view 3
VAS 5052 4
Vehicle Diagnosis and Service Information System
Version -GB- / V01.02 20/08/2001
5
Vehicle
Self-diagnosis 6
ElsaWin
Applications
Administration
Print Help
IrDA + -
VAS 5052
256_007
7 8 9 10 11
Top view
12 13 14 15 16 17 18 19
COMPACT DVD-ROM
256_008
Bottom view
20 156_026 256_009
21 22
8
Legend relating to p. 8:
11 On/Off switch
9
Design and Interfaces
Mechanical design
– On/Off switch
10
A base station with integral mains unit, included in
the parts supplied, rounds off the VAS 5052 system
for fixed installation.
USB interface
– USB interface
– interface for base station
– inlet connector Interface
of base station
The mains unit incorporated in the base station can Inlet connector
also be used for recharging the battery.
A quick-charge in normal ambient conditions 256_010
(+ 5 °C up to 40 °C) takes about 120 minutes.
Accessories
Also supplied in addition to the base station Further available accessories
VAS 5052/2 the following parts are also included
– the diagnostic adapter, VAS 5051/2
– one diagnostic cable (5 m), VAS 5052/3 (for older vehicles)
– one test adapter for diagnostic cable, VAS – the LT diagnostic cable, VAS 5051/4 and
5052/4 – the Self-Study Programme „VAS 5052“,
– one carry case, VAS 5052/5 VAS 5052/22
– one abbreviated instructions, VAS 5052/6
– the base CD, VAS 5052/7 can be ordered as required.
– headphones, VAS 5052/8
– the multimedia CD „VAS 5052“, VAS 5052/9
– three touchpens, VAS 5052/11 and
– a case as packaging and for transportation,
VAS 5052/15.
11
Operating Modes
– Vehicle Self-Diagnosis
– Applications
– Administration and
– Help
– Screens
– Buttons
– Selection lists
– Scroll bars
– Cursor
– Virtual keypads in different versions
– Hour glass for displaying processes in
progress
12
Switching on tester and booting
The tester is supplied ready for operation. When the tester is switched on for the first time,
the following screen appears:
It is switched on by pressing the On/Off button.
When this is done, the booting operation is
started, the computer performs the start process
and after a short time displays the start screen.
VAS 5052
Vehicle Diagnosis and Service Information System
Version -GB- / V01.02 20/08/2001
Administration
Print Help
256_011
When the tester is operated for the first time, it is Select the button „Administration“ in order to
necessary to enter the dealer data in order to open the screen „Administration/Select function“
have available the buttons for the operating for entering the „Workshop code“:
modes of „Vehicle Self-Diagnosis“ and
„Applications“.
Select function
Install update
Self-test
Enter workshop code
Signal generator
Date/Time
Expanded functions
Choose starting image
Table of Contents
Print format
ESIS Installation or Update
ELSA Installation
Activate Telediagnosis
Go to Print Help
256_012 13
Operating Modes
Confirmation of entry
Warning:
After confirmation of the entry,
no further change
in the importer number and the dealership
number is possible.
Cancel OK
Go to Print Help
256_013
14
Administration Equipment number: 54329
Importer number: 452
Dealership number: 54325
Select function John Smith, Ltd.
Install update
Self-test
Change dealership identification
Signal generator
Date/Time
Expanded functions
Select initial graphics
CD contents list
Print format
Install or update ESIS
User manual
Activate telediagnosis
Enter IP address
Install ELSA
Go to Print Help
256_014
15
Operating Modes
– Step 1:
The 3-digit VZ/Importer number is requested in
a separate dialog screen. This number is 452
entered by the user using the virtual numerical
keypad which is displayed. 1 2 3
The digits entered are shown in the a display
field.
4 5 6
It is possible to enter up to three digits. A 7 8 9
warning signal sounds if too many digits are
entered. C 0 Q
256_003
– Step 2:
You are now requested to enter the 5-digit
dealership number.
The entry is basically made in the same way as 54325
before.
1 2 3 4 5 6 7 8 9 0
After these two steps are completed, a check
question appears to ensure that the data q w e r t y u i o p
entered are correct. You have the opportunity to a s d f g h j k l SH
make any corrections at this stage.
C z x c v b n m Q
If you confirm the check question - Confirm
entry with „OK“ -, the screen for the third step 256_002
„Enter dealership identification“ now appears.
– Step 3:
This entry is made using a virtual,
alphanumerical keypad with a switch function
using the key „SH“, into a display field with two
entry lines.
The equipment number which appears in front
„SH“ (Shift) means switch over between upper
of the VZ/Importer number is already entered
case/lower case letters.
in the factory.
„Q“ (Quit) - confirming each line - is pressed to
complete the entry.
16
The dialog between the user and the VAS 5052
makes use of standardised screens, the layout
being basically the same as shown below.
1 - Screen
Vehicle self-diagnosis
2 - Button
4
Select vehicle system
3 - Working window
59 - TowingInformation
protection 5
3 69 - Trailer function
4- Information window
33 - OBD IIText
Select vehicle system using address word 6
5 - Selection bar
01 - LT Diesel regulation
25 - LT Immobiliser 7
6 - Dialog box 81 - LT Engine management
82 - LT ABS
92 - LT ABS/ABD 5.3
7 - Scroll bar Overview
83 - LT Tachograph Close
8
84 - LT Auxiliary heater
87 - LT Airbag/belt tensioner
8 - Cursor
Go to Print Help
9 - Navigation line 9
256_015
1 2
Buttons are used for switching functions on/off. A selection bar identifies the line you have
The graphical appearance of the buttons selected. The bar appears „black“ and the
changes according to the selection. lettering „white“.
In the majority of cases, the next screen appears
Working windows offer selection lists for as soon as you have made your selection.
completing data. You can make your selection,
for example, by touching (touchscreen) the A dialog box is an information field in a main
appropriate line with your finger. The selection is screen. It displays additional information,
activated when you take your finger away. operating facilities in order to be able to perform
further steps, or fault messages.
Information windows are provided in the
majority of screens above the working window. A scroll bar is shown at the right-hand margin of
The left-hand information window shows the the dialog box or of a screen if it is not possible
operating mode, subfunctions in the operating to show all of the text.
mode and operating instructions. It consists of a slide and two arrows. It is possible
The right-hand window shows terms which have to move up and down within the text by touching
previously been selected, or results. the symbols.
You can „scroll“ line-by-line using the „up“ or
„down“ arrows.
17
Operating Modes
The navigation line is positioned in the bottom Virtual keypads are displayed in the different
part of the screen. operating modes depending on the particular
function, and hidden again after the data entries
With the buttons located in this line it is possible have been completed.
to select Help and Service functions. Depending on the function, a numerical or
The number of buttons depends on the particular alphanumerical keypad is shown (refer to p. 16).
screen and on the current state.
Go to Print Help
256_017
256_016
18
Vehicle self-diagnosis
With the diagnostic cable connected and the This operating mode is started by clicking the
ignition switched on (depending on the vehicle button „Vehicle Self-Diagnosis“ in the start
system), it is possible in this operating mode to screen.
communicate with the systems fitted to the
vehicle.
Vehicle self-diagnosis
256_019
What appears is a listing of all the vehicle The process is displayed in the left-hand
systems introduced and the user-specific information window by means of the text
extensions. „Establishing communication“.
Communication is maintained until the
The consecutive list is subdivided by blank lines diagnostic function „End output“ is selected or by
into pressing the button „Back“ in the navigation line.
19
Operating Modes
In this function, the fault memories relating to all It is possible to make a selection from the vehicle
the vehicle systems entered in the screen „Select systems of the light van.
vehicle system“, are read out one after the other In the case of the LT2 vehicle systems it is only
(provided they are installed) and their contents possible to use the LT functions or the OBD functions.
are displayed together with a number of stored The LT diagnostic cable VAS 5051/4 is required.
faults in the screen which follows.
33 - OBD function
Vehicle self-diagnosis
33 - OBD
Select diagnosis mode
Go to Print Help
256_020
20
Diagnostic functions for vehicle systems
After communication with the control unit has In the screen displayed, all the diagnostic
been started by making a selection in the screen functions are shown as a standard feature.
„Select vehicle system“, the subsequent screen
then appears. If a function is not available in connection with a
particular vehicle system, the tester answers in
the left information window with the message:
A selection of the diagnostic functions (repair „Function unknown or cannot be carried out at
orders) matching the vehicle appears on the left the moment“.
of the screen while the control unit identification
read from the vehicle system, is shown at the top
right in the information window.
The functions offered depend on the vehicle
system.
Go to Print Help
256_021
21
Operating Modes
Administration
Print format
Install or update ESIS Administration
User’s manual
Activate telediagnosis Help
Enter IP address
Install ELSA
Go to Print Help
256_018
After the tester has been started for the first time, „Change dealership identification“ makes it
it is possible to set the diagnostic system in the possible to enter a different name or address of
operating mode „Administration/Select function“ the company.
- as you are familiar with from VAS 5051.
„Signal generator“ - For certain operating
processes an audible signal is generated, the
The „Install update“ function makes it possible to duration and volume of which can be set here.
load more recent programme versions from the
CD to the hard disc. „Date/Time“ - Date and time can be displayed
At the same time the specific language is set in here After completing the entry, it is then only
the system by the CD-ROM. possible to change the time.
The new version status is shown in the start Hours and minutes can be set independently of
screen. each other. There are two buttons available
which can be selected separately. The time is
The „Self-test“ function performs an internal changed accordingly by pressing on the side
check of the EDIC (Electronic Diagnostic direction arrows.
Interface Computer) diagnostic bus interface
card. The diagnostic cable should be
disconnected for this step. For the remaining
parts of the self-test, the diagnostic cable should
be plugged in again - with a special test adapter The date can only be changed after
provided. The diagnostic cable is tested for short re-installation of a base CD.
circuits and open circuits in the wiring. After confirming the entry with the
„Accept“ button, it is no longer
possible to address the date setting.
The button is no longer shown.
22
„Expanded functions“ are not required in normal „User Manual“ - When this function is selected,
workshop operation. the Adobe Acrobat Reader displays the PDF
They are available only to a selected group of document „Manual.pdf“ in a separate screen.
users and are activated by means of the so- (The base CD should not be inserted for this
called code CDs. step.)
The screen consists of a large display field
„Select start graphic“ - Different start images are (including slide control), four buttons arranged
part of the base CD data. vertically at the right-hand margin for operating
The user is able to select an image from these. the „Zoom“, „Original size“, „Back“, „Forward“
This image is then displayed in the start screen. functions and also the navigation line at the
bottom margin of the screen.
„CD contents list“ - The CD contents file is part of The „Back“, „Go to“, „Print“ and „Help“ buttons
the base CD data. This function can be used to are positioned on this line.
display the contents list of the base CD installed. Display of the PDF document is integrated in the
user interface of VAS 5052.
„Print format“ - Here you can select one of the
formats - either 4 or US Letter - for the next log „Activate telediagnosis“ - This function is
printout or screen extract. provided for activating the telediagnosis. After
being selected, the display changes to
„Install or Update ESIS“ - This function can be „Deactivate telediagnosis“.
used to optionally install the „Electronic Service
Information System“. „Enter IP address“ makes it possible to enter the
This is used only in the US market. IP address assigned to the tester.
The ESIS CD set is not part of the scope of supply.
„Install ELSA“ - This function is used for installing
the „Electronic Service Information System -
ELSA“.
The ELSA CD set is not part of the scope of
supply.
23
Operating Modes
Applications
After the „Applications“ mode has been started, – Title display and selection
the selection list of the available applications is – Start
then displayed.
Applications
Select application
Go to Print Help
IrDA + -
VAS 5052
256_022
24
Applications
Select application
Applications
Service Training
Yes No
Vehicle electronics 3
Mr
Mrs
First name:
Last name:
Date of birth:
Contents
Customer number:
Dealership number:
~ ! @ # $ % ^ & * ( ) _ +
1 2 3 4 5 6 7 8 9 0 - =
/
´
Q W E R T Y U I O P { }
[ ] Enter
Vehicle electronics 3
: Confirm:
Caps A S D F G H J K L “
Lock ; Batteries and rechargable batteries
Z X C V B N M < > ?
, . /
Electrics fields and capacities
Measurements
Final test
Vehicle Electronics 3
256_028
25
Operating Modes
Job note:
Workshop Manual
Maintenance Tables
Internet
Emission Test
256_023
26
Example:
Electronic Service Information System - [Workshop Manual]
Service Edit View Settings ? After selecting the icon „Workshop Manual“ a
Job note:
Search for:
screen appears for the „Vehicle Identification“
_
Overview
X which then has to be completed.
Brand Designation Sales Type Designation OK
Selection locked
V Volkswagen 3B2 Passat
Cancel
Model year
200
Code
1 AKN
Type
TP
CCM
2.5
kW
110
Designation
TURBO-DIESEL Reset
After entering „OK“ to confirm the identification,
Vehicle ID No.: Gearbox Type Number Designation a list of the „Assemblies“ which can be selected
DQT 6 01E.J
drawings.
Job Note:
Search for:
_
Overview
+ Brake system
+ Electrical system
+ Running gear Electronic Service Information System - [Workshop Manual]
Overview
Job Note:
Search for:
VAS 5052 together with the ELSA software can
7 Attention! be used in combination with a server as a client-
1
2
Bonded rubber mountings can only be twisted slightly. Therefore,
the vehicle must be standing on its wheels before you tighten the
bolted connections on the control arms of the suspension.
server version, or by installing on the hard disc
6 5
1 - Coupling with rubber mounting
Rubber mounting with attached shim -A-
must be bolted to anti-roll bar.
of the equipment.
2 - Self-locking hexagon nut
A 3 40 Nm and turn 90° further
4 3 - Hexagon nut
Overview
256_024 27
Operating Modes
Help Print
Here you can display operating information and The Print function is selected by pressing on the
explanations of functions relating to a particular „Print“ button in the navigation line.
context or of a general nature. The Print functions available are shown in the
selection list.
The data which you wish to print are transmitted
via an IrDA interface (infrared data transfer).
„Help“ is not a substitute for the User Manual! It is possible to print out the contents file of
It can, however, assist you in the workshop if the base CD with up-to-date information in the
there are any unclear questions regarding „Administration“ mode.
how to use the screens and the buttons.
The following Print functions are available in the
„Vehicle self-diagnosis“ mode:
– Store results
The Help functions are divided into two groups: – Self-diagnosis log
– Output medium (printer or disc, the output
– Subjects medium disc is intended for future applicati-
– Buttons ons)
– Enter licence plate/vehicle identification num-
The „Help“ button appears in every screen and ber (for display in self-diagnosis log)
always at the same point in the navigation line.
28
A further attribute of VAS 5052, in addition to its
use as a stand-alone version in the workshop, is
that it can be linked via a server to the office, the
parts store, reception … in the client-server
version (software basis is the VAUDIS-VW Audi
Information System).
Stand-alone unit
The illustration below shows how the VAS 5052 is
linked to the office and to other processors.
IrDA + -
VAS 5052
256_029
VAS 5052
ELSA
Workshop network
(client-server)
Reception
VAUDIS
ELSA
VAUDIS
ELSA
Server
VAUDIS
ELSA (ELWIS)
IrDA + -
VAS 5052
29
Notes
30
Notes
31
256
Service.