You are on page 1of 7

Ordering number : ENN6501

LA4627
Monolithic Linear IC

LA4627
Two-Channel Audio Frequency Power Amplifier

Overview Package Dimensions


The LA4627 is a 2-channel power amplifier de- unit : mm
veloped for use in radio/cassette player products. 3022B-DIP12F
The LA4627 reduces the number of required ex-
[LA4627]
ternal components by 50% over earlier products
(BS/NF capacitors and oscillation prevention RC
19.0
components) and thus can contribute significantly 12 7
to space saving in end products.

7.62
6.45
Features

0.4
• Provided in the DIP12F. 1 5.12 6
• PO :2.0 W ✕ 2 (VCC = 9 V, RL = 4 Ω) 3.6 1.25

4.26max
2.5 W ✕ 2 (VCC = 9 V, RL = 3 Ω)

(3.46)
• Standby function built in

0.51min
(supports direct microcontroller control).

3.5
• Built-in thermal protection circuit.
0.5 1.3
(0.61) 2.54 3.81
SANYO : DIP12F(300mil)

Specifications
Maximum Ratings at Ta = 25°C
Parameter Symbol Conditions Ratings Unit
Maximum supply voltage VCC max Rg = 0 22 V
Allowable power dissipation Pd max When mounted on the Sanyo-recommended PCB 4.0 W
Operating temperature Topr --25 to +75 °C
Storage temperature Tstg --55 to +150 °C

Operating Conditions at Ta = 25°C


Parameter Symbol Conditions Ratings Unit
Recommended supply voltage VCC 9 V
Recommended load resistance RL 3 Ω
Operating voltage range VCC op Under conditions such that the maximum ratings are not exceeded. 5.0 to 20 V
Recommended operating load resistance RL op 2.7 to 8.0 Ω

Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft's
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.

SANYO Electric Co.,Ltd. Semiconductor Company


TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN

42000 RM (IM) No.6501-1/6


LA4627

Operating Characteristics at Ta = 25°C, VCC = 9 V, RL = 3 Ω, f = 1 kHz, Rg = 600 Ω


Ratings
Parameter Symbol Conditions Unit
min typ max
Quiescent current ICCO Rg = 0 17 30 70 mA
Voltage gain VG VO = 0 dBm 43 45 47 dB
Total harmonic distortion THD PO = 0.33 W(VO = 1.0 V) 0.1 0.8 %
Output power PO(1) THD = 10 % 2.0 2.5 W
PO(2) THD = 10 %, RL = 4 Ω 2.0 W
Output noise voltage VNO Rg = 0, DIN AUDIO 0.15 0.5 mVrms
Ripple rejection ratio SVRR Rg = 0, fR = 100 Hz, Vr = 0 dBm, DIN AUDIO 45 52 dB
Channel separation CHsep Rg = 0, VO = 0 dBm, DIN AUDIO 50 60 dB
Standby current IST Rg = 0 1.0 10 µA
Input resistance Ri 20 30 40 kΩ
Standby pin voltage VST The pin 1 voltage such that the amplifier is on 1.5 5.0 V

Pd max -- Ta
7
6.4 Copper heat sink (Fin 1)
Allowable power dissipation, Pd max -- W

25.0
8.7
6 5.7 Steel heat sink (Fin 1) 10.7

5 4.9
Steel heat sink (Fin 2)
Mounted on the recommended
printed circuit board. 25.0

53.0
4
4.0 8.7
10.7
3

12.0
2 1.9
Independent IC

3.6 0.5 3.6 0.5


8.0

8.0
1

0
--20 0 20 40 60 80 Fin 1 Fin 2
Ambient temperature, Ta -- °C ILA00055 ILA00056

Application Circuit

+
output 1
100 µF

+ +
4.7 µF

1000 µF
RL POWER 1 µF
+
GND input 1
12 11 10 Fin 9 8 7

VCC OUT1 P. P DC IN1


VCC (R. F)
1000 µF

+ LA4627

PRE
STBY OUT2 GND IN2

*Rx 1 2 3 Fin 4 5 6
+
4.7 kΩ input 2
STBY
+5 V 1 µF
Top view
+ • Pins 3, 5, 10 must be left open.
output 2
1000 µF *• Rx: If the STBY pin (pin 1) is used, observe the following:
RL
Insert the resistor Rx in series to limit the inflowing current.
(The amplifier will be on when a voltage is applied to pin 1.) ILA00057

No.6501-2/6
LA4627

Block Diagram
STBY VCC
1 12

Standby SW

ch1
7 ch1
Input ch1 input Output
11
amplifier amplifier Output

Rf1

RNf1

REF
PRE GND 4 amplifier TSD protector Fin POWER GND

RNf2
Rf2

ch2 input Output ch2


ch2 amplifier amplifier 2
Output
Input 6

Pop noise prevention block Ripple filter

9 8

P.P Filter

ILA00059

Pin Functions
1. Standby switch function (pin 1)

Rx STBY 2 kΩ
1
+
2 kΩ

Applied standby
voltage Vx The inflowing current at an
applied voltage of 1.5 V, i.e.
the point when the amplifier
turns on, is approximately
750 µA.
ILA00058
STBY pin applied voltage: 5 V
To hold the pin 1 inflow current to about 750 µA insert a resistor (Rx) of 4.7 kΩ
STBY pin applied voltage: 12 V
To hold the pin 1 inflow current to about 750 µA insert a resistor (Rx) of 14 kΩ (12 kΩ).
STBY pin applied voltage: Other value (Vx)
To hold the pin 1 inflow current to about 750 µA insert a resistor (Rx) of (Vx - 1.5 V)/750 µA.

• If a microcontroller output signal is applied directly, insert a resistor in series


and adjust the current to a level optimal for the drive capability of the
microcontroller.

2. Input pins (pins 6 and 7)


The input pin voltage is about 2VBE (1.4 V).
The input pin impedance is about 30 kΩ.
• Although the recommended value for the input capacitor is 0.22 µF, the starting time can be modified by changing the
value of this capacitor. (The time from the point a voltage is applied to the standby pin to the point sound is emitted.)

Input capacitor 1.0 µF 2.2 µF 3.3 µF 4.7 µF 10 µF


Starting time (ts) 0.2 s 0.3 s 0.5 s 0.65 s 1.5 s

No.6501-3/6
LA4627

3. FILTER (decoupling) pin (pin 8)


The pin voltage is about 1/2 VCC.
The recommended value for the filter capacitor is 100 µF.
The pulse noise that occurs when the standby pin is set low (power off) will be degraded if a value under 100 µF is
used.
AC voltage (100 mV) AC voltage (200 mV)

Output DC voltage Output DC voltage

ILA00061 ILA00062

Filter capacitor = 100 µF Filter capacitor = 47 µF

VCC

4. P.P (pulse noise) pin (pin 9)


Pin 9 pin voltage ≈ VCC - VCE (about 0.3 V) - 5.6 V + 5.6 V
2 kΩ

5 kΩ
• The recommended value for the P.P capacitor is 4.7 µF.
The pulse noise that occurs when the standby pin is set low (power off) will 9
be degraded if a value under 2.2 µF is used.

5 kΩ
Furthermore, if a value over 10 µF is used, the signal may not be cut off and
sound may remain audible when the standby pin is set low (power off).
Zener voltage
= 5.6 V
To the input amplifier
block/bias system

ILA00063

5. MUTE (Muting)
The output signal can be controlled by shifting the pin 8 (FILTER) level towards ground with a 300 to 500 Ω resistor.
However, note that the degree of suppression is reduced if a value of 750 Ω or more is used.

Output AC voltage

Output DC voltage

Mute ON Mute OFF ILA00064

No.6501-4/6
LA4627
VCC -- PO VCC -- ICCO
10 140
f = 1 kHz Rg = 0
THD = 10 % RL = 3 Ω
120

Quiescent current, ICCO -- mA


8

Output power, PO -- W

4 100
=
RL
6
80


3
=
4
RL Ω 60
=8
RL
40

2
20

0 0
4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20 22 24
Supply voltage, VCC -- V ILA00065 Supply voltage, VCC -- V ILA00066
THD -- f THD -- PO
10 100
7 VCC = 9 V 7 VCC = 9 V
5 RL = 3 Ω 5
RL = 3 Ω
Total harmonic distortion, THD -- %

Total harmonic distortion, THD -- %


3
3 VO = 1 Vrms 2
2 10
7
1.0 5
7 3
5 2
3 1.0 f = 10 kHz
7

100 Hz
2 5

1 kHz
3
0.1 2
7
5 0.1
7
3 5
2 3
2
0.01 0.01
10 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k 0.1 2 3 5 7 1.0 2 3 5 7 10
Frequency, f -- Hz ILA00067 Output power, PO -- W ILA00068
CHsep -- f SVRR -- fR
0 0
VCC = 9 V VCC = 9 V
--10 RL = 3 Ω RL = 3 Ω
Ripple rejection ratio, SVRR -- dB

--10
Channel separation, CHsep -- dB

VO = 0 dBm Rg = 0
--20
Rg = 10 kΩ Vr = 150 mVrms
--20 DIN AUDIO
--30
--30
--40
--40
--50
➝1
CH2 --50
2
--60 CH1➝

--70 --60

--80 --70
10 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k 10 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k
Frequency, f -- Hz ILA00069 Ripple frequency, fR -- Hz ILA00070
f -- Response VNO -- Rg
2 1.0
VCC = 9 V VCC = 9 V
RL = 3 Ω 0.9 RL = 3 Ω
Output noise voltage, VNO -- mVrms

0 VO = 0 dBm DIN AUDIO


VG = 45.5 dB 0.8

0.7
--2
Response -- dB

0.6

--4 0.5

0.4
--6
0.3

0.2
--8
0.1

--10 0
10 2 3 5 7100 2 3 5 7 1k 2 3 5 710k 2 3 5 7100k 1k 2 3 5 7 10k 2 3 5 7 100k
Frequency, f -- Hz ILA00071 Signal source resistor, Rg -- Ω ILA00072

No.6501-5/6
LA4627
Pd -- PO
5
f = 1 kHz
Pd = VCC ✕ ICC -- 2 ✕ PO
4
Power dissipation, Pd -- W


3 =3
RL
V/
=9
VC C
4627
2 LA
=4Ω
9V / RL
27 VC C=
1 LA42

0
0.1 2 3 5 7 1.0 2 3 5 7 10
Output power, PO -- W ILA00073

Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer’s
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer’s products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products(including technical data,services) described or
contained herein are controlled under any of applicable local export control laws and regulations,
such products must not be exported without obtaining the export license from the authorities
concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.

This catalog provides information as of April, 2000. Specifications and information herein are subject
to change without notice.
PS No.6501-6/6
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.

You might also like