Professional Documents
Culture Documents
Part #1110-0104-11 “Black Ice” Part #1110-B104-11 Upper Only Part #1110-010U-11
Quantity Description Part No. Quantity Description Part No. Quantity Description Part No.
1 Upper Mesh Grille (includes): ************* 1 Upper Mesh Grille (includes): ************* 1 Upper Mesh Grille (includes): *************
(1) Top Mounting Plate 1110-0210-11 (1) Top Mounting Plate 1110-0210-11 (1) Top Mounting Plate 1110-0210-11
(1) 12 Gage Stainless Steel Surround 1110-0038-11 (1) 12 Gage Stainless Steel Surround 1110-0038-11 (1) 12 Gage Stainless Steel Surround 1110-0038-11
(1) Upper “Heavy” Mesh Section 1110-0040-11 (1) “Black Ice“ Heavy Mesh Section 1110-0040-11BI (1) Upper Mesh Section 1110-0040-11
(1) Lower Retainer w/Mounting Pins 1110-0042-11 (1) Lower Retainer w/Mounting Pins 1110-0042-11 (1) Lower Retainer w/Mounting Pins 1110-0042-11
(16) #8-32 ESNA Half Nuts 1999-0065-00 (16) #8-32 ESNA Half Nuts 1999-0065-00 (16) #8-32 ESNA Half Nuts 1999-0065-00
(2) Small Black Plastic Washers 1999-0256-00 (2) Small Black Plastic Washers 1999-0256-00 (2) Small Black Plastic Washers 1999-0256-00
1 Lower Mesh Grille Surround 1110-0022-11 1 Lower Mesh Grille Surround 1110-0022-11 1 Hardware Kit (components listed below) 1110-1903-11
1 Lower “Heavy” Mesh Section 1110-0041-11 1 Lower “Black Ice” Heavy Mesh Section 1110-0041-11BI (1) Hole Location Template 1110-0039-11
1 Hardware Kit (components listed below) 1110-1902-11 1 Hardware Kit (components listed below) 1110-1902-11 (2) #10 Stainless Steel Lock Washers 1999-9555-00
(8) 1” x .189” x .064” Black Plastic Washers 1999-0264-00 (8) 1” x .189” x .064” Black Plastic Washers 1999-0264-00 (2) #8-32 Stainless Steel Hex Nuts 1999-9072-00
(6) #8-32 ESNA Half Nuts 1999-0065-00 (6) #8-32 ESNA Half Nuts 1999-0065-00 (1) Emblem Mounting Plate 1110-0158-08X
(5) 8-32 x .1” Black Cap Plugs 1999-0241-00 (5) 8-32 x .1” Black Cap Plugs 1999-0241-00 (2)#8 x 1/2” Truss Head Screws 3999-9035-00
(1) Upper Grille Hole Location Template 1110-0039-11 (1) Upper Grille Hole Location Template 1110-0039-11 (1’) .045” x 1/4” Double Faced Tape 3004-9250-92
(2) #10 Stainless Steel Lock Washers 1999-9555-00 (2) #10 Stainless Steel Lock Washers 1999-9555-00 (2) 1” x .189” x .064” Black Plastic Washers 1999-0264-00
(2) #8-32 Stainless Steel Hex Nuts 1999-9072-00 (2) #8-32 Stainless Steel Hex Nuts 1999-9072-00
(1) Emblem Mounting Plate 1110-0158-08X (1) Emblem Mounting Plate 1110-0158-08X Lower Only Part #1110-010L-11
(4)#8 x 1/2” Truss Head Screws 3999-9035-00 (4)#8 x 1/2” Truss Head Screws 3999-9035-00
(1’) .045” x 1/4” Double Faced Tape 3004-9250-92 (1’) .045” x 1/4” Double Faced Tape 3004-9250-92 Quantity Description Part No.
1 Lower Mesh Grille Surround 1110-0022-11
1 Lower “Heavy” Mesh Section 1110-0041-11
1 Hardware Kit (components listed below) 1110-1905-11
Important information before you begin: (6) 1” x .189” x .064” Black Plastic Washers 1999-0264-00
(6) #8-32 ESNA Half Nuts 1999-0065-00
(5) #8 x 3/4” Black Cap Plugs 1999-0241-00
This E&G grille installation kit includes grille (2)#8 x 1/2” Truss Head Screws 3999-9035-00
hole location template(s) to drill mounting
holes in the vehicle. 1
2
Before marking or drilling any holes into the
vehicle, you MUST verify that the template(s)
provided in this kit match the mounting pin
locations on the grille(s).
7
6
8
10
9. The outer lower corners of the grille slide out from 10. Pull the grille straight out to remove it from the
8. Remove the factory grille from the bumper cover by mounting channels in the headlight mounting bumper cover. Unbolt the license plate bracket (if
unclipping the four (4) push fasteners from across panel. equipped) prior to lower mesh grille installation.
the bottom of the factory grille (see enlargement).
Use a large screwdriver to push down on the center
of the push pins to release them.
2 Copyright 2010 by E&G Classics, Inc.
WARNING:
PLEASE HANDLE WITH CARE ! THE
EDGES OF THE STAINLESS STEEL MESH
& GRILLE CAN BE EXTREMELY SHARP!
14
10
13
11. Trim the ends from the black cap plugs and push
them down onto the lower mounting studs to 13. Peel the protective layer from the mesh surround 14. Install the supplied large black plastic washers and
conceal them once the lower grille is installed. prior to installation. Apply masking tape to the #8-32 ESNA half nuts onto each of the mounting
12. Align the lower mesh section to the back of the lower factory grille opening to protect the paint studs and tighten until the washers no longer
lower surround. during the lower grille installation. Align the mesh freely rotate. DO NOT OVERTIGHTEN or you could
and surround into place. damage the lower surround at the stud locations.
16
17
15
9 20
19
18
18. Use a .125” (1/8”) drill bit to drill through the 19. Use a 5/16” drill bit to enlarge the hole drilled in 20. Use a 1/2” diameter drill bit to enlarge the holes in
marks made onto the upper portion of the bumper the previous step. the bumper cover for lower ESNA half nut clear-
cover for preinstalled ESNA nut clearnace. ance.
23
22
21
22. Shop Tip: For cars painted colors other than black 23. Remove the emblem from the factory grille and
or dark blue: Tape 1/4” inside the upper bumper install it onto the supplied emblem mounting plate
21. Reinstall the hood latch surround back onto the opening and use a scotch brite pad or fine sand- using the supplied double faced tape. Apply tape
radiator support panel, then use a disc grinder to paper to scuff the factory paint and paint the to the sides of the emblem and one strip down
remove the four (4) tabs across the front egde. return with flat or semi-gloss black paint. For all each side of the “H”.
cars: Paint any visible portion of the radiator and
core support with flat or semigloss black paint and
allow to dry.
25
25. Align the mesh grille mounting pins with the holes
drilled in Step 14. Once all the pins are aligned,
24. Align the emblem mounting plate onto the mesh push the mesh grille down to begin seating the
pins. Carefully remove the protective masking tape 27. Install the factory push pins through the cover and
grille, making sure that the plate is centered and into the top plate on the E&G grille and through
level. Install the large black plastic washers, #10 from the painted bumper cover by peeling it back
over itself to minimize tape breakage (not shown), the bumper cover on the outer edges.
lock nuts and #8-32 stainless steel hex nuts and
tighten. then finsh pushing the grille tightly against the
bumper cover.
26. Realign the radiator cover, making sure the sides of
the top mounting plate fit into the radiator cover.
28 30
16
29
8