Professional Documents
Culture Documents
KEY BENEFITS
Q Low priced scalable options – event reports, waveform capture, Q Two settings groups
reclosure, breaker fail Q Password protection for local operation
Q Reduce troubleshooting and maintenance cost – Event Q Automatic display of last fault information
reports, waveform capture
Q AC/DC power supply
Q Design flexibility – Easy to use programming logic
Q Improved user interface
Q Asset monitoring – Breaker health, and breaker failure
Q Access via front panel keypad or communication links
protection
Q EnerVista compatible
Q Access to information – Modbus RTU communications
Q Isolated front RS232 serial port
Q Configurable logic, curves, I/Os and LEDs
Q Flash memory for field upgrades
APPLICATIONS
Q Primary circuit protection on distribution networks at any Q Backup/auxiliary protection for transformers, generators
voltage level and motors
FEATURES
Protection and Control Monitoring and Metering
Q Phase and ground TOC and IOC Q 32-event record
Q Thermal image protection Q Analog/digital oscillography
Q Option “N” for single phase or ground applications Q KI2 counter for breaker maintenance
Q IAC time-current curves Q Per phase current metering
Q EPTAR-C time-current curves Q Monitoring of the last 5 trips information from the display
Q Circuit breaker control (open and close) User Interface
Q Four shot autorecloser Q EnerVista for setting and monitoring
Q Cold load pickup element Q 2x16 character LCD display
Q Configurable breaker failure to open Q 6 LED indicators, 4 configurable in function and colour.
Q Configurable I/O Q Front RS232 and rear RS485 ports using ModBus®RTU
Q 6 outputs: trip, service required, 4 auxiliary protocol up to 19,200 bps
183
MIF II Feeder Protection System MIF II Feeder Protection System
distribution networks at any voltage level, urable curve. Each curve can be set with Level: ±1% at the rated current < 0.08 VA @ In = 1A secondary Approximate Weight:
allow setup and configuration of MIF units. customized time multipliers to coordinate ANSI Inverse, Very Inverse < 0.08 VA @ In = 1A sensitive ground, Net: 8.8 lbs (4 kgs)
or Extremely Inverse Ship: 9.9 lbs (4.5 kgs)
and backup/auxiliary protection for IAC Inverse, Very Inverse, Extremely
secondary
The MIF II can be accessed with a PC using with equipment. Inverse, Inverse Short or Inverse Long
Current Withstand:
transformers, generators and motors. Time delayed (0.00 to 600.00 sec. in 4 x In continuously TYPE TESTS
the M II EnerVista Setup Software via the steps of 0.01 sec. 100 x In for 1 sec. Test Standard Class
Basic protection features include time Time Dial: 0.05 to 2 in steps of 0.01 for IEC curves DIGITAL INPUTS InsulationTest Voltage:
RS232 communication port located in the Ground TOC (51G) 0.5 to 20 in steps of 0.1 for ANSI curves Voltage Level: 300 Vdc maximum
delayed overcurrent, instantaneous over- 0.5 to 10 in steps of 0.1 for IAC curves Recognition Time: < 4 ms
IEC 60255-5 2kV, 50/60 Hz 1 min
relay front panel. Use EnerVista to view or Reset Type: Instantaneous
Surge Test Voltage:
current (two levels), and thermal image This element has the same curve selection Timing Accuracy:
IEC 60255-5 5 kV, 0.5 J.
modify settings and relay configuration POWER SUPPLY (3 positive pulses
protection. Overcurrent elements can be choices and settings as the phase time ± 3% of set time for I > 1.50 times the
LOW RANGE
and 3 negative.)
(inputs, outputs, LEDs and configurable Actual Pickup Level for IEC/ANSI/ 1 MHz Interference:
three-phase and ground or single phase, overcurrent element. The ground signal is definite time curves Rated DC Voltage: 24 to 48 Vdc IEC 60255-22-1 III
logic), as well as to display metering ± 6% of set time for I > 1.50 times the Min./Max. DC Voltage: 19 / 58 Vdc Electrostatic Discharge:
depending on the selected model. normally derived as the residual sum of Actual Pickup for IAC curves
8 information, and real time status. If the Type/measure time: HIGH RANGE IEC 60255-22-2
EN 61000-4-2
IV
8 kV in contact,
8
An optional protection offering is also pro- the three-phase CTs eliminating the need DFT of 1 cycle Rated DC Voltage: 110 to 250 Vdc 15 kV through air
relay was furnished with the appropriate PHASE / GROUND INSTANTANEOUS OVERCURRENT Min./Max. DC Voltage: 88 / 300 Vdc
vided for cold load pickup, breaker failure for an additional ground sensor. For more (50P1, 50P2, 50G1, 50G2) Rated AC Voltage: 110 to 230 Vac @ 50 – 60 Hz
Radiointerference:
option, use EnerVista to display last fault Current: Fundamental Min./Max. AV Voltage: 88 / 264 Vac @ 50 – 60 Hz
IEC 60255-22-3: III
protection, breaker health, configurable sensitive detection, an additional core Pickup Level: 0.1 to 30.0 times In (rated current) in 40 MHz,
information such as event reports and an steps of 0.1 x In. (50P1/P2 & 50G1/G2 151 MHz,
logic, and autorecloser. balance (zero sequence) ground sensor for 1/5 A ground models)
Power Consumption: Max. = 10 W 450 MHz and
oscillography records. The MIF has a 0.005 to 0.12 A (50G1/G2 for sensitive Backup time: (date, time and log memory) cellular phone.
Each protection element can be selectively encircling the three-phase conductors can ground models) without power supply voltage Radiated Electromagnetic
drawout construction in 1/4 of a 19'' rack Dropout Level: 97% (typical) of Pickup > 1 week fields with amplitude
enabled either via the front panel or via be used. Overreach: < 2% modulation:
case. OUTPUTS ENV 50140 10 V/m
communications. Flexible settings, and Time Delay: 0.00 to 600.00 sec. in steps of 0.01 s
OUTPUT RELAYS Radiated Electromagnetic
selectable models for ANSI, IEC, IAC or Instantaneous Overcurrent (50) Reset Type: Instantaneous
Configuration: 6 Electro-Mechanical Form C fields with amplitude
Operate Time: Between 20 and 30 ms for I> 1.5 x Contact Material: Silver alloy suited for inductive modulation. Common mode.
EPTAR-C curves enable accurate coordina- Protection The MIF II includes two separately Timing Accuracy:
Actual Pickup loads
Maximum Operating Voltage:
ENV 50141
Radiated Electromagnetic
10 V/m
tion with other devices. adjustable IOC elements, each of which ± 3% of settled time for I > 1.5 times 400 Vac fields with frequency
The MIF II provides primary circuit the Actual Pickup Continuous Mode Current: modulation.
The basic MIF II has two fixed digital inputs can be independently enabled. MIF II Type/measure time: 16 A at 250 Vac. ENV 50204 10 V/m
protection for distribution networks of any DFT of 1 cycle
general purpose Fast Transients:
and six fixed digital outputs. An option is models provide two three-phase IOC THERMAL IMAGE ELEMENT (49) ¾ HP, 124 Vac ANSI/IEEE C37.90.1 IV
voltage, and backup/auxiliary protection Current: Fundamental IEC 60255-22-4 IV
elements and two ground IOC elements. 1-1/2 HP, 250 Vac
provided allowing the two inputs and four BS EN 61000-4-4 IV
for transformers, generators and motors. Pickup Level: 0.10 to 2.40 In in steps of 0.01 x In 10A, 250 Vac, 0.4 PF,
Magnetic fields at industrial
of the outputs to be user configurable. The pickup setpoint can be set from 0.1 to Dropout Level: Between 97% typical of Pickup Level B300 pilot duty
frequency:
As part of the M II Family, the MIF II Level Accuracy: ±1% at In
Make and Carry: 30 A
EN 61000-4-8 30 AV/m
30 times In and a time delay from 0 to 600 Breaking: 4000 VA
The basic MIF II has six fixed status LEDs. provides advanced digital protection ±3% in the complete range RELAY CONTACTS
Power Supply interruptions:
seconds. Heating Constant T1: Max rating for 10,000 operations
IEC 60255-11
An option is provided allowing four of these which includes: Temperature: IEC 57 (CO) 22
From 3 to 600 min in steps of 1 min. Voltage Make M&C Break Max RF Emission: EN 55011 B
LEDs to be user configurable. The front Cooling Constant T2: &Carry CONT. 0.2 seg Load Sinusoidal Vibration:
Thermal Image Unit (49) From 1 to 6 times ?1 in steps of 1. DC Resist 24 Vdc 16A 48A 16A 384W IEC 60255-21-1 II
panel also features a 5-button keypad and Overcurrent Protection Thermal Image Alarm: 48 Vdc 16A 48A 2.6A 125W Shock: IEC 60255-21-2 I
A thermal image element protects equip- From 70% to 100%Ipickup in steps 125 Vdc 16A 48A 0.6A 75W Insulation Test:
a 16x2 LCD display that provides an easy A variety of time curves are provided, of 1% 250 Vdc 16A 48A 0.5A 125W IEC255-5
ment against overheating due to excessive (Tested on CTs,
to use user interface. depending on model. It includes GE IAC, Timing Accuracy: AC Resist 120Vdc 16A 48A 16A 1920VA Power Supply
load. Several operating curves can be set 5% for operate times greater than 250 Vdc 16A 48A 16A 4000VA terminals,
The front keypad allows the user to set the ANSI, IEC, EPTAR-C (for resistive earths), 2 sec. Inductive 250 Vdc 10A 30A 10A 1000VA Contact Inputs
as a function of heating time constant T1 (PF=0.4) and Contact
baud rate and relay address for communi- definite time and user-programmable METERING Outputs)
(adjustable between 3 and 600 minutes). MECHANICAL CHARACTERISTICS
cation. curves. See ordering code for details. The FUNDAMENTAL CURRENT
APPROVALS
Cool down time constant T2 is adjustable Accuracy: ±1% at In • Metallic package in 1/4 19'' rack and 4 units high
A front RS232 and a rear RS485 communi- GE-IAC curves inverse, very inverse, ±3% in the complete range • Protection class IP52 (according to IEC 529) UL: UL listed
from one to six times the heating time CE: Conforms to EN/IEC 60255
cation port are provided for computer extremely inverse, short and long inverse ISO: Manufactured to an ISO9001 registered program
constant. MONITORING * Specifications subject to change without notice
access using ModBus®RTU protocol. The allow retrofit of most popular electro- OSCILLOGRAPHY
mechanical IAC relays. Records: 1 x 24 cycles
rear RS485 can be converted to an RS232 Sampling rate: 8 samples per power frequency cycle
Triggers: Any element pickup or operation
Ordering
Digital input configured as MIF II * * * * * * * * 00
Functional Block Diagram oscillography trigger
Communications command
P
N
3 phase + ground relay
Single phase or ground relay
Information: AC input channels
Digital input/output channels
A ANSI curves
Self-test events I IEC curves
EVENT RECORDER U IAC curves
52 Capacity: 32 events C EPTAR-C curves (only for single phase model)
Time-tag: To 1 millisecond 0 MIF II N models
Triggers: Any element pickup, operation or reset. 1 MIF II P models: Phase CT in = 1 A
79 Digital input/output change of state 5 MIF II P models: Phase CT in = 5 A
Self-test events
CLOSE TRIP 1 Ground CT In = 1 A
5 Ground CT In = 5 A
METERING
COMMUNICATIONS N Sensitive ground: CT In = 1 A
Local Communication: 2x16 LCD Display L Very sensitive ground: CT In = 1 A
Monitoring 5 button frontal keypad E English language
BREAKER HEALTH
Remote Communication: F French language
BREAKER FAILURE TO OPEN
(local or remote PC and communications net): 0 MIF II Basic Model
OSCILLOGRAPHY Mode: ModBus® RTU 1 MIF II Option 1 *
EVENT RECORDING Baud rate: 300 to 19200 bps 2 MIF II Option 2 **
COLD LOAD PICKUP
CONFIGURABLE I/O AND LEDS
DB9 connector for RS232 ports on the front (1) and 0 Without recloser
RS485 on the rear
CONFIGURABLE LOGIC
R With recloser (not available in the Basic Model)
1 50G-1 50G-2 51G 49 LO 24-48 VDC (Range: 19~58 Vdc) Power Supply
Accessories HI 110-250 VDC (Range: 88~300 Vdc) Power Supply
B1315P1 Depth reducing collar. Reduces the 110-230 VAC (Range: 88~264 Vac) Power Supply
MIF II N mounting depth by 2.45 inches. * Configurable I/O/LEDs, event recording, oscillography
EN MIFII N BLOCK ** Option 1 + cold load pickup, breaker failure to open, breaker health, configurable logic
B1343P1 S1/S2 case adapting collar for retrofit
installations
www.GEMultilin.com www.GEMultilin.com
184 189
MIF II Feeder Protection System MIF II Feeder Protection System
g
means of a setting, a communication
RS485
TRIP COIL -
TRIP
COIL Multilin MIF II SDB A12(*)
events, and includes the values of currents
A5 B
TRIP command or contact input activation.
CONTROL Feeder Protection System
and status of all the protection elements at
POWER + A6 GND B11 (*) GROUND Cold Load Pickup
Settings classified into two categories, the moment of the event.
This feature adapts the pickup of the
READY
ESC
www.GEMultilin.com www.GEMultilin.com
188 185
MIF II Feeder Protection System MIF II Feeder Protection System
User Interface Q Converts Modbus RTU over RS485 into relevant data and options for the relay it is the industry experience of GE, all in one
Modbus TCP/IP over Ethernet communicating with. This eliminates very cost-effective package.
Q Supports both 10BaseT and 10BaseF having to manually configure the relay Unlike complicated tools consisting of mul-
DISPLAY fiber connections within the software and provides a simple tiple applications, EnerVista VIEWPOINT
16x2 characters LCD display for
viewing setpoints, actual value Q Connect up to 32 RS485 serial devices to and easy to use operator user interface. offers a truly simplified user interface.
messages, and fault reports
an Ethernet network Creating a site diagram is as easy as drag-
Q Modbus TCP/IP provides multiple SCADA ging and dropping icons for analog and
STATUS INDICATION LEDs
Four of six status LEDs are masters allowing simultaneous commu- digital values. Monitored quantities are
user programmable in function nications to the same IED presented in familiar formats like gauges
and color
Q Flexible mounting options allow retro- fit and dials. You can also choose an annunci-
CONTROL AND to existing devices ator panel view that provides a virtual front
PROGRAMMING KEYS
Escape, Reset, Enter, Menu Up, Q Industrially hardened for utility and panel for your equipment complete with
and Menu Down keys for complete industrial applications alarm and alert notification.
access to settings and information
without a computer Q Simple “plug & play” device setup with
8 EnerVista software 8
www.GEMultilin.com www.GEMultilin.com
186 187