Professional Documents
Culture Documents
INCH-POUND
MS27039F
15 NOVEMBER 1995
SUPERSEDING
MS27039E
24 JANUARY 1995
The requirements for acquiring the product described herein shall consist of this specification
sheet and the issue of the following specification listed in that issue of the Department of Index of
Specifications and Standards (DODISS) specified in the solicitation: MIL-S-7839
MS27039F
NOTES:
REQUIREMENTS:
1. Material:
Aluminum Alloy 2024 (UNS A92024) in accordance with QQ-A-430, Temper 2024-D, or
QQ-A-225/6, Temper T4.
Manganese Bronze (UNS C67000) in accordance with ASTM B138.
Alloy Steel 8630 (UNS G86300) in accordance with MIL-S-7839, 26-32 HRC or 8740
(UNS G87400), 4130 (UNS G41300) in accordance with MIL-S-6049.
Heat and Corrosion-Resistant Steel, A286 Iron Base Super Alloy (UNS S66286) in
accordance with AMS 5731 or AMS 5732.
3. Tensile strength:
Aluminum Alloy: 62,000 psi min ultimate tensile strength.
Manganese Bronze: 85,000 psi min ultimate tensile strength.
Alloy Steel: 125,000 to 145,000 psi ultimate tensile strength.
Heat and Corrosion-Resistant Steel: 130,000 psi min ultimate tensile strength.
4. Threads:
Threads shall be accordance with FED-STD-H28/2. Acceptability of screw threads shall
be in accordance with FED-STD-H28/20, system 21.
5. Recess:
The recess shall be in accordance with MS9006.
2
Downloaded from http://www.everyspec.com on 2011-03-21T13:32:03.
MS27039F
7. Part number:
The part number shall consist of the basic MS number followed by the material and finish code
followed by the dash number.
Example: MS27039DD0809 indicates - Screw, Machine - Pan Head Structural, Cross Recessed;
.164-32 UNC-3A, .594 length, Anodized Aluminum
Alloy Screw.
MS27039BP 0809 indicates - Screw, Machine - Pan Head Structural, Cross Recessed;
.164-32 UNC-3A, .594 length, Cadmium Plated
Manganese Screw.
MS27039B0809 indicates - Screw, Machine - Pan Head Structural, Cross Recessed;
.164-32 UNC-3A, .594 length, uncoated Manganese
Bronze Screw.
MS27039 - 0809 indicates - Screw, Machine - Pan Head Structural, Cross Recessed;
.164-32 UNC-3A, .594 length, Cadmium Plated Alloy
Steel Screw.
MS27039C0809 indicates - Screw, Machine - Pan Head Structural, Cross Recessed;
.164-32 UNC-3A, .594 length, Heat and Corrosion-
Resistant Steel Screw.
8. Head marking:
a. Basic part no. and applicable dash no. (Basic part optional for .164-32 screw sizes).
b. Material as follows: Aluminum Alloy - none, Bronze - “B”, Alloy Steel - “-”, Heat and Corrosion-
Resistant Steel -”C”.
c. Manufacturer’s trade-mark shall be added, location optional.
Table I. Dimensions
R
Thread ∅A ∅B C Rad U Max Eccentricity
Head to Recess to
Max Min Max Min Max Min Max Min Shank Fim Shank Fim
.164-32 UNC-3A .1640 .1610 .322 .306 .115 .105 .020 .016
.190-32 UNF-3A .1890 .1860 .373 .357 .133 .122 .024 .020
.250-28 UNF-3A .2490 .2460 .492 .473 .175 .162 .020 .010 .032 .030 .024
.3125-24 UNF-3A .3115 .3085 .615 .594 .218 .203 .036
.375-24 UNF-3A .3740 .3710 .740 .716 .261 .244 .042
.4375-20 UNF-3A .4365 .4325 .868 .838 .304 .286 .025 .015 .047 .048 .030
.500-20 UNF-3A .4990 .4950 .987 .958 .348 .327 .030 .020 .056
2_/ Based on 60% of the minimum ultimate tensile strength at nominal shank diameter times two.
3
Downloaded from http://www.everyspec.com on 2011-03-21T13:32:03.
MS27039F
Thread
.164-32 UNC-3A .190-32 UNF-3A .250-28 UNF-3A .3125-24 UNF-3A
Dash Length Grip Dash Length Grip Dash Length Grip Dash Length Grip
No No No No
0804 .281 1 - 04 .281 4 - 04 .281
0805 .344 1 - 05 .344 4 - 05 .344 5 - 05 .359
0806 .406 1_/ 1 - 06 .406 1_/ 4 - 06 .406 1_/ 5 - 06 .422
0807 .469 1 - 07 .469 4 - 07 .469 5 - 07 .484 1_/
0808 .531 .094 1 - 08 .531 .062 4 - 08 .531 5 - 08 .547
1 - 49 3.094 2.626
1 - 50 3.156 2.688
1 - 51 3.219 2.751
1 - 52 3.281 2.813
1 - 53 3.344 2.876
1 - 54 3.406 2.938
1 - 55 3.469 3.000
1 - 56 3.531 3.063
4
Downloaded from http://www.everyspec.com on 2011-03-21T13:32:03.
MS27039F
+ .032
1_/ Short screws listed above lines shall be threaded to within .032 − .000 of the head.
Table III. Dash Numbers and Dimensions. - continued
Thread
.375-24 UNF-3A .4375-20 UNF-3A .500-20 UNF-3A
Dash Length Grip Dash Length Grip Dash Length Grip
No No No
6 - 05 .406
6 - 06 .469 7 - 06 .453 8 - 06 .453
6 - 07 .531 7 - 07 .516 8 - 07 .516
6 - 08 . 594 1_/ 7 - 08 .578 1_/ 8 - 08 .578 1_/
+ .032
1_/ Short screws listed above lines shall be threaded to within .032 − .000 of the head.
5
Downloaded from http://www.everyspec.com on 2011-03-21T13:32:03.
MS27039F
Review activities:
Army - AV, ME, MI
Air Force - 82
NA