You are on page 1of 37

2007-2008

ELECTRONIC KITS CATALOGUE

0 1 0 8 2 0 0 7

www.anykits.co.in
sales@anykits.co.in
AUDIO/HI-FI 1

ALARM/SOUND EFFECTS 4

MICROCONTROLLER/INTERFACE 7

TEST & MEASUREMENT 14

TIMER & CONTROLLER 16

LIGHT EFFECTS 18

POWER SUPPLY 20

REMOTE CONTROL 25

BUILDING BLOCKS 26

MINI KITS 28

MISCELLANEOUS 30

MOTOR/MOTION CONTROL 32

sales@anykits.co.in www.anykits.co.in
AUDIO/HI-FI

STEREO TAPE HEAD TDA2006 12W AUDIO


PREAMPLIFIER A002 AMPLIFIER A003

The Stereo Tape Head Preamplifier kit is based on LA3161 IC from SANYO. TDA2006 12W Audio Amplifier Kit is a Low Frequency Class AB amplifier.
¦ Power supply - 9 ~ 12 VDC @ 20 mA ¦ Power supply - upto 18 VDC
¦ Output power - upto 200 mW ¦ Output power - 12 W @ 4 Ω, 8 W @ 8 Ω
¦ Input Resistance - 100 KΩ (Typ), Load ¦ TDA2006 provides high output current
Resistance - 10 KΩ (Typ) ¦ Has very low harmonic and cross-over
¦ Low noise, good ripple rejection owing to distortion
the on-chip voltage regulator ¦ Short circuit protection / Thermal
¦ Berg pins for connecting power supply, shutdown system in IC
input and output ¦ Terminal pins for connecting left and right
¦ Power-On LED indicator audio signal inputs
¦ Four mounting holes of 3.2 mm each ¦ Relimate Connector for connecting
¦ PCB dimensions 51 mm x 54 mm Potentiometer (POT) for volume adjustment
¦ Power Battery Terminal (PBT) for easy
power supply and speaker connection
¦ Power-On LED indicator
5.5W + 5.5W AUDIO ¦ Heatsink for IC
AMPLIFIER A004 ¦ Four mounting holes of 3.2 mm each with
nut and stud
5.5W + 5.5W Audio Amplifier Kit is based on LA4445 IC form SANYO. It ¦ PCB dimensions 51 mm x 63 mm
can be used as a car radio amplifier, tape recorder etc.
¦ Power supply - 12 - 16 VDC
¦ Output power - 5.5 W + 5.5 W @ 4 Ohm
¦ Good ripple rejection, good channel TINY AUDIO AMPLIFIER A005
separation, small residual noise
¦ Thermal, overvoltage, short protector
The Tiny Audio Amplifier kit is a good choice for battery operation. It is
inbuilt into IC
based on LM386 IC.
¦ Terminal pins for connecting left and right
audio signal inputs ¦ Power supply - 6 - 12 VDC
¦ Relimate Connector for connecting ¦ Output power - 1 W, 8 Ohm
Potentiometer (POT) for volume adjustment ¦ The quiescent power drain is only 24 mW
¦ Power Battery Terminal (PBT) for easy when operating from 6 VDC
power supply and speakers connection ¦ Self-centering output quiescent voltage
¦ Power-On LED indicator ¦ Onboard PRESET to adjust volume
¦ Heatsink for IC ¦ Terminal pins for connecting power supply,
¦ Four mounting holes of 3.2 mm each with audio signal and speaker
nut and stud ¦ Power-On LED indicator
¦ PCB dimensions 44 mm x 74 mm ¦ ON/OFF PCB mounted slide switch for
power supply
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 44 mm x 44 mm
LM4730 STEREO 14W
AUDIO AMPLIFIER A006

LM4730 Stereo 14W Audio Amplifier kit can be used for High-end Stereo MIC PREAMPLIFIER A008
TVs, Compact Stereo etc.
¦ Dual power supply - ±18 VDC
MIC Preamplifier kit using standard Op-Amp circuit.
¦ Output power - 14 W + 14 W, 8 Ohm
¦ Less then 10% THD+N from 20 Hz - 20 KHz ¦ Power supply - 5 - 12 VDC @ 10 mA
¦ Onboard slide switch for mute and standby ¦ Output - Gain 100
mode ¦ On-Board Condenser MIC
¦ Terminal pins for connecting left and right ¦ Terminal pins for connecting of power
audio signal inputs supply and output
¦ Relimate connector for connecting ¦ Power-On LED indicator
Potentiometer (POT) for volume adjustment ¦ Four mounting holes of 3.2 mm each
¦ Power Battery Terminal (PBT) for easy dual ¦ PCB dimensions 40 mm x 39 mm
power supply and speakers connection
¦ Power-On LED indicator
¦ Heatsink for IC
¦ Four mounting holes of 3.2 mm each with
nut and stud 1.6W MONO AUDIO
¦ PCB dimensions 82 mm x 88 mm AMPLIFIER A011

1.6W Mono Audio Amplifier kit is based on TDA7231, which is class AB


power amplifier with a wide range of supply.
¦ Power supply - 5 ~ 12 VDC
¦ Output - 1 W, 4 Ω
¦ Low crossover distortion, soft clipping
¦ Onboard PRESET to adjust volume
¦ Terminal pins for connecting power supply,
input and output
¦ ON/OFF PCB mounted slide switch for
power supply
¦ Power-On LED indicator
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 36 mm x 52 mm

sales@anykits.co.in 1 www.anykits.co.in
AUDIO/HI-FI

STEREO 10W AUDIO 20W BRIDGE AUDIO


AMPLIFIER A009 AMPLIFIER A010

Stereo 10W Audio Amplifier kit is a Hi-fi Stereo Amplifier, it is based on 20W Bridge Audio Amplifier kit, based on the TDA2005 IC, a class B dual
TDA1521 IC. audio amplifier, specifically designed for car radio applications etc.
¦ Power supply - 18 VDC ¦ Power supply - 18 VDC
¦ Output power - 2 X 10 W (THD 0.5%), 8 Ω ¦ Output power - 20 W, 4 Ω
¦ Excellent gain balance between channels. ¦ IC built in Thermal Shut-down, Load dump
Gain 30 dB voltage surge protected
¦ IC is short circuit and thermally protected ¦ Terminal pins for connecting left and right
¦ Terminal pins for connecting left and right audio signal inputs
audio signal inputs ¦ Relimate Connector for connecting
¦ Power Battery Terminal (PBT) for easy Potentiometer (POT) for volume adjustment
power supply and speakers connection ¦ Power Battery Terminal (PBT) for easy
¦ Power-On LED indicator power supply and speaker connection
¦ Heatsink for IC ¦ Power-On LED indicator
¦ Four mounting holes of 3.2 mm each with ¦ Heatsink for IC
nut and stud ¦ Four mounting holes of 3.2 mm each with
¦ PCB dimensions 39 mm x 65 mm nut and stud
¦ PCB dimensions 63 mm x 65 mm

STEREO AUDIO PREAMPLIFIER A013


MONO AUDIO PREAMPLIFIER A012
The Stereo Audio Preamplifier kit has been developed to amplify the low
level stereo audio signal. It can be used as Mic preamplifier etc. The Mono Audio Preamplifier kit has been developed to amplify the low
level audio signals. It is based on commonly available Op-Amp. It can be
¦ Power supply - 12 - 24 VDC @ 40 mA
used as a Mic preamplifier etc.
¦ Onboard PRESET to adjust Gain, Level
¦ Berg connector for connecting of input and ¦ Power supply - 12 ~ 24 VDC @ 20 mA
output ¦ Output - Gain 35 adjustable
¦ Terminal pins for connecting power supply ¦ Onboard PRESET to adjust Gain, Level
¦ Power-On LED indicator ¦ Terminal pins for connecting power supply,
¦ Four mounting holes of 3.2 mm each input and output
¦ PCB dimensions 47 mm x 58 mm ¦ Power-On LED indicator
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 44 mm x 42 mm

MINI STEREO AUDIO


AMPLIFIER A015
10W + 10W AUDIO AMPLIFIER A014
Mini Stereo Audio Amplifier kit is designed for portable radio players
and other building block projects. It is based on TDA2822 IC.
The 10W + 10W Audio Amplifier kit, built around TDA2004 IC, Which is a
¦ Power supply - upto 12 VDC class B dual audio power amplifier, specifically designed for car radio
¦ Output - 1 W, 8 Ω for 12 VDC / 20 mW, applications etc.
32 Ω for 3 VDC
¦ Power supply - 15 VDC
¦ Input resistance - 100 KΩ
¦ Output power - 2 X 6.5 W, 4 Ω / 2 X 10 W,
¦ Low crossover distortion, Low quiescent

current
¦ IC built in short circuit, thermal shut-down,
¦ Onboard PCB mount 3.5 mm stereo jack
load dump voltage surge protection
for audio-in
¦ Terminal pins for connecting left and right
¦ Onboard Presets to adjust volume
audio signal inputs
¦ Terminal pins for connecting power supply
¦ Relimate Connector for connecting
and outputs
Potentiometer (POT) for volume adjustment
¦ Power-On LED indicator
¦ Power Battery Terminal (PBT) for easy
¦ Four mounting holes of 3.2 mm each
power supply and speakers
¦ PCB dimensions 41 mm x 56 mm
¦ Power-On LED indicator
¦ Heatsink for IC
¦ PCB dimensions 67 mm x 73 mm

1.6W AUDIO AMPLIFIER A016

1.6W Audio Amplifier kit can used as a low frequency class B power TINY MIC PREAMPLIFIER A017
amplifier with wide range of supply voltage.
¦ Power supply - 3 - 12 VDC The Tiny Mic Preamplifier kit is based on a single transistor amplifier
¦ Output - 1.6 W, 4 Ω / 1.2 W, 8 Ω design. It amplifies the output of the condenser Mic. Good choice for
¦ Input resistance - 5 MΩ Karaoke.
¦ Low quiescent current, good ripple
¦ Power supply - 5 - 9 V DC @ 2 mA
rejection and no cross-over distortion
¦ PCB dimensions 26 mm x 56 mm
¦ Onboard presets to adjust volume
¦ Terminal pins for connecting power supply,
input and output
¦ Four mounting holes of 3.2 mm each
¦ PCB Dimensions 44mm x 47mm

sales@anykits.co.in 2 www.anykits.co.in
AUDIO/HI-FI

AUDIO SIGNAL TO LIGHT UNIT A019 5 LED VU METER A018

Audio Signal to Light Unit kit is an audio to light modulator, which controls 5 LED VU Meter kit is based on LB1403 IC from SANYO, which will indicates
the intensity of light in response to an audio input. This kit is ideal for the volume level of the audio signal it senses.
dance parties, DJ, Discotheques etc.
¦ Power supply - 6 ~ 12 VDC @ 90 mA
¦ Input - Audio signal ¦ Lighting levels remain stable to line
¦ AC Power supply - 230 VAC regulation because of on-chip voltage
¦ Load - 230 W reference
¦ Input isolated with the use of Opto-coupler ¦ LED's are driven by a constant current
¦ Onboard Presets to adjust level ¦ Onboard presets to adjust input sensitivity
¦ Terminal pins for connecting audio input ¦ Terminal pins for connecting power supply,
¦ Four mounting holes of 3.2 mm each audio input
¦ PCB dimensions 36 mm x 50 mm ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 34 mm x 52 mm

12W HI-FI AUDIO AMPLIFIER A021


6W MONO AUDIO AMPLIFIER A020
12W Hi-Fi Audio Amplifier kit built around TDA2030 IC, intended to be
used as a low frequency class AB amplifier. 6W Mono Audio Amplifier kit is based on TDA2003 IC.
¦ Power supply - 24 VDC ¦ Power supply - 14 VDC
¦ Output - 12 W, 4 Ω ¦ Output - 6 W, 4 Ω
¦ Input resistance - 5 MΩ ¦ Input resistance - 150 KΩ
¦ Very low harmonic distortion (0.5%) and ¦ Very low harmonic and cross-over
cross-over distortion distortion
¦ IC built in Short circuit, Thermal shut-down ¦ IC built in short circuit, thermal over-
¦ Terminal pins for connecting audio input range, load dump voltage surge protected
¦ Power Battery Terminal (PBT) for easy ¦ Onboard PRESET to adjust volume
power supply and speaker connection ¦ Terminal pins for connecting audio input
¦ Power-On LED indicator ¦ Power Battery Terminal (PBT) for easy
¦ Heatsink for IC power supply and speaker connection
¦ Four mounting holes of 3.2 mm each with ¦ Power-On LED indicator
nut and stud ¦ Heatsink provided for IC
¦ PCB dimensions 39 mm x 60 mm ¦ Four mounting holes of 3.2 mm each with
nut and stud
¦ PCB dimensions 33 mm x 71 mm

6W + 6W STEREO AUDIO
AMPLIFIER A023

6W + 6W Stereo Audio Amplifier kit is based on LA4440 IC from SANYO.


5W STEREO AUDIO AMPLIFIER A022
¦ Power supply - 12 VDC
5W Stereo Audio Amplifier Kit based on BA5406 IC is suitable for
¦ Output - 2 X 6 W, 4 Ω
application like stereo radio cassette player, stereo components systems
¦ Input resistance - 30 KΩ
etc.
¦ Low distortion (THD - 0.1%), Good
channel separation and ripple rejection ¦ Power supply - 12 VDC
¦ IC built-in thermal, overvoltage, pin-to-pin ¦ Output - 5 W + 5W, 3 Ω
short protector ¦ Input resistance - 100 KΩ
¦ Terminal pins for connecting inputs ¦ Good distortion (THD - 0.3%), Good
¦ Power Battery Terminal (PBT) for easy channel balance
power supply and speakers connection ¦ Berg pins for connecting of inputs
¦ Power-On LED indicator ¦ Power Battery Terminal (PBT) for easy
¦ Heatsink for IC power supply and speakers connection
¦ Four mounting holes of 3.2 mm each with ¦ Power-On LED indicator
nut and stud ¦ Heatsink for IC
¦ PCB dimensions 41 mm x 72 mm ¦ Four mounting holes of 3.2 mm each with
nut and stud
¦ PCB dimensions 45 mm x 73 mm

20W AUDIO AMPLIFIER A024

20W Audio Amplifier kit is based on LM1875 IC.


¦ Power supply - 48 VDC
¦ Output - 20 W, 4 Ω
¦ Very low distortion (THD 0.015%), good
channel separation and ripple rejection
¦ IC built-in thermal, short circuit protections
¦ Internal output protection diodes
¦ Terminal pins for connecting input
¦ Power Battery Terminal (PBT) for easy
power supply and speaker connection
¦ Power-On LED indicator
¦ Heatsink for IC
¦ Four mounting holes of 3.2 mm each with
nut and stud
¦ PCB dimensions 48 mm x 60 mm

sales@anykits.co.in 3 www.anykits.co.in
ALARM/SOUND EFFECTS

20 SEC VOICE RECORD / 120 SEC VOICE RECORD /


PLAYBACK B001 PLAYBACK B002

20 Sec Voice Record / Playback kit will playback and record upto 20 120 Sec Voice Record / Playback kit will playback and record upto 120
seconds of voice message. This kit is an excellent choice to add voice to seconds of voice message. This kit is built around ISD25120 IC.
your project. This kit is built around ISD1420 IC.
¦ Input supply - 5 VDC @ 120 mA
¦ Input supply - 5 VDC @ 120 mA ¦ Output - speaker, 16 Ω
¦ Output - Speaker, 16 Ω ¦ Upto 120 Seconds of non volatile voice
¦ Upto 20 Seconds of non volatile voice storage
storage ¦ Slide switch for easy selection of Playback
¦ Power-On LED indicator / Record mode
¦ Onboard MIC capsule for recording ¦ Onboard MIC capsule for recording
message directly onto the chip message directly onto the chip
¦ Flashing LED to display Record / Playback ¦ Flashing LED to display Record / Playback
of messages of messages
¦ Direct speaker connection via Relimate ¦ ON Board ON/OFF Switch
Connector ¦ Power-On LED indicator
¦ Relimate type connector for Power Supply ¦ Direct speaker connection via Relimate
Input Connector
¦ 4 pin small tactile switches for Record and ¦ Relimate type connector for power supply
Play function trigger input
¦ Four mounting holes of 3.2 mm each ¦ 4 pin small tactile switches for Start /
¦ PCB dimensions 59 mm x 67 mm Pause and Stop / Reset
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 57 mm x 75 mm

WATER LEVEL BUZZER B003


LIGHT SENSITIVE AUDIO
OSCILLATOR B004
Water Level Buzzer is a simple kit which will buzz when water reaches the
sensor level.
Light Sensitive Audio Oscillator kit is a fun loving kit which will create
¦ Input - 9 VDC @ 40 mA
different sound effects depending on the light falling on the sensor (LDR).
¦ Output - Buzzer
¦ Terminal pins for supply voltage ¦ Input - 5 ~ 12 VDC
¦ Power-On LED indicator ¦ Output - Speaker
¦ Four mounting holes of 3.2 mm each ¦ Terminal pins for supply voltage and
¦ PCB dimensions 32 mm x 35 mm speaker connection
¦ Power-On LED indicator
¦ PCB dimensions 38 mm x 44 mm

3 TONE MUSICAL BELL B005

3 Tone Musical Bell is a kit built around BT66T IC driving LM386 audio 3 TONE AUDIO OSCILLATOR B006
amplifier to give that extra punch.
¦ Input - 6 VDC @ 200 mA 3 Tone Audio Oscillator is a simple circuit which will generate audio tone on
¦ Output - Speaker the press of a button. This circuit can be very useful as a test equipment for
¦ Terminal pins for supply voltage and audio equipments or as a signal source for an audio input.
speaker connection
¦ Power-On LED indicator ¦ Input - 12 VDC @ 100 mA
¦ ON/OFF Switch on the PCB ¦ Output - Speaker, 8 Ω / 0.25 W
¦ Four mounting holes of 3.2 mm each ¦ Three switches produce 1.5 KHz, 1 KHz
¦ PCB dimensions 35 mm x 54 mm and 450 Hz
¦ Terminal pins for supply Voltage and
speaker connection
¦ Power-On LED indicator
¦ Four mounting holes of 3.2 mm each
3 TONE SIREN B008 ¦ PCB dimensions 42 mm x 48 mm

3 Tone Siren kit produces Gun Sound, Police Siren and Ambulance Siren
effects from a speaker. This kit is built around UM3561 IC driving an
LM386 audio amplifier to give that extra punch. 2 TONE AUDIO OSCILLATOR B007
¦ Input - 6 VDC @ 200 mA
¦ Output - Speaker, 8 Ω / 0.5 W 2 Tone Audio Oscillator is a simple circuit which will generate audio tone on
¦ Two slide switches select and play different the press of a button. This circuit can be very useful as test equipment for
tones audio equipment or as a signal source in an audio input.
¦ ON/OFF slide switch for power supply
¦ Terminal pins for supply voltage and ¦ Input - 5 ~ 12 VDC @ 100 mA
speaker output ¦ Output - Speaker, 8 Ω / 0.25 W
¦ Power-On LED indicator ¦ Two switches produce / play different
¦ Four mounting holes of 3.2 mm each frequencies
¦ PCB dimensions 42 mm x 64 mm ¦ Terminal pins for supply voltage
¦ Power-On LED indicator
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 47 mm x 46 mm

sales@anykits.co.in 4 www.anykits.co.in
ALARM/SOUND EFFECTS

AUDIO OSCILLATOR B009 VOICE MODULATOR B010

Audio Oscillator kit simply produces audio tones for use in the range of 115 Voice Modulator kit is designed around HT8950A to provide two special
Hz to 1 KHz. This kit is a must for audio technicians and experimenters sound effects viz. Vibrato & Robot.
alike.
¦ Input - 6 VDC @ 300 mA
¦ Input - 6 VDC @ 325 mA ¦ Output - Speaker, 8 Ω / 0.5 W
¦ Output - Speaker, 8 Ω / 0.5 W ¦ 7 Step level shifting (Volume Control) SW3
¦ Range 115 Hz to 1 KHz selectable by (TGU) and SW4 (TGD)
onboard PRESET ¦ SW2 - vibrato mode, SW5 - robot mode
¦ ON/OFF slide switch for power supply ¦ LED to display the voice level input
¦ Terminal pins for supply voltage and ¦ ON/OFF slide switch for power supply
speaker output ¦ Audio amplifier type LM386 with volume
¦ Power-On LED indicator control preset
¦ Four mounting holes of 3.2 mm each ¦ PBT (Power Battery Terminal) connectors
¦ PCB dimensions 39 mm x 42 mm for supply voltage and speaker output
¦ Power-On LED indicator
¦ PCB dimensions 63 mm x 68 mm

VOICE CHANGER B011


TELEPHONE SIREN COB B012
Voice Changer kit can be used to transpose or distort one's voice by
encoding the sound appearing at the Microphone input. This kit is built
around AP8072 IC. Telephone Siren COB kit can be used to emulate the Telephone Ringer
sound for your project without the need of a telephone line. This kit can be
¦ Input - 6 VDC @ 200 mA
used in toys and science fair projects.
¦ Output - Speaker, 8 Ω / 0.5 W
¦ Audio amplifier type LM386 with volume ¦ Input - 3 VDC (2 AAA Battery)
control preset ¦ Output - Speaker, 8 Ω / 0.25 W
¦ Slide switch selectable tone frequency for ¦ Tactile switch for trigger
encoding sound ¦ Four mounting holes of 3.2 mm each
¦ 4 Tones to choose ¦ PCB dimensions 31 mm x 39 mm
¦ Built in noise reduction circuit for reducing
environment noise
¦ ON/OFF slide switch for power supply
¦ Terminal pins for supply voltage and
speaker output
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 61 mm x 65 mm
VOICE MODULE 60 SEC B015

Voice Module 60 Sec kit will playback and record upto 60 seconds of voice
VOICE MODULE 20 SEC B014 message. This kit is an excellent choice to add voice of upto 350 mW to
your project.
Voice Module 20 Sec kit will playback and record upto 20 seconds of voice ¦ Upto 60 Seconds of non volatile voice
message. storage
¦ Upto eight segments record and play
¦ Upto 20 Seconds of non volatile voice
option available
storage
¦ Easy and clear, jumper selectable mode
¦ Onboard MIC capsule for recording
option
message directly onto the chip
¦ Reset switch available for use in Tape
¦ A stereo socket to record voice from an
mode
external audio source
¦ Upto 350 mW of audio output available to
¦ Easy jumper selection for selecting
drive a speaker
recording source
¦ Onboard MIC capsule for recording
¦ Flashing LED to display Record / Playback
message directly onto the chip
of messages
¦ A Stereo socket to record voice from an
¦ Direct speaker connection via Relimate
external audio source
Connector
¦ Easy jumper selection for selecting
¦ Relimate type connector for power supply
recording source
input
¦ Flashing LED to display Record / Playback
¦ 4 pin small tactile switches for Record and
of messages
Play function trigger
¦ Direct speaker connection via Relimate
¦ Onboard voltage regulator for a regulated
Connector
supply
¦ Relimate type connector for power supply
¦ Diode protection against reverse polarity
input
connection of power supply
¦ 4 pin small tactile switches for Record and
¦ Preset for adjusting sampling rate and
Play function trigger
record level of voice record/play
¦ Onboard voltage regulator for a regulated
¦ 28-Pin IC socket for the main IC
supply
¦ Four mounting holes of 3.2 mm each
¦ Diode protection against reverse polarity
¦ PCB dimensions 70 mm x 58 mm
connection of power supply
¦ Preset for adjusting sampling rate, record
level and Volume Level of voice record/play
¦ PCB dimensions 72 mm x 103 mm

sales@anykits.co.in 5 www.anykits.co.in
ALARM/SOUND EFFECTS

APR9600 ADD-ON VOICE


MULTI TUNE COB B013 MODULE B016

Multi Tune COB will provide different tunes for your project. The output APR9600 Add-On Voice Module kit will playback and record upto 60
from the COB (Chip On Board) will drive an audio amplifier based on seconds of voice message. This kit is an excellent choice to add voice to
LM386. Can also be used as a Door Bell. your project.
¦ Input - 6 VDC @ 200 mA ¦ Upto 60 Seconds of non volatile voice
¦ Output - Speaker, 8 Ω / 0.5 W storage
¦ Tactile switch for trigger ¦ Upto eight segments record and play
¦ Power-On LED indicator option available
¦ Terminal pins for supply voltage and ¦ All trigger inputs and supply available for
speaker output easy connection to your controlling
¦ Four mounting holes of 3.2 mm each interface
¦ PCB dimensions 35 mm x 63 mm ¦ Jumper selectable mode option
¦ Jumper enabled record option
¦ Reset switch available for use in Tape
mode
¦ Onboard MIC capsule for recording
message directly onto the chip
¦ Flashing LED to display Record / Playback
of messages
¦ Direct speaker connection via Relimate
Connector
¦ 5V DC Power Supply required
¦ Preset for adjusting sampling rate, record
level and Volume Level of voice record/play
¦ 28 pin IC socket for the main IC
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 67 mm x 52 mm

sales@anykits.co.in 6 www.anykits.co.in
MICROCONTROLLER/INTERFACE

PIC16F 28-PIN DEVELOPMENT PIC18F 28-PIN DEVELOPMENT


BOARD C001 BOARD C002

PIC16F 28-Pin Development Board will help you with your prototyping PIC18F 28-Pin Development Board will help you with your prototyping
requirement with any of Microchip's 28pin PIC microcontrollers. requirement with any of Microchip's 18F 28pin PIC microcontrollers.
¦ 16X2 backlight LCD which mounts on the ¦ ICSP connector for programming for the PICs
back side (Track Side) of the PCB with ICD support
¦ ICSP connector for programming for the ¦ 28-Pin ZIF socket for the microcontroller
PIC's with ICD support ¦ 20 Mhz Crystal with jumpers to connect to
¦ 2 LED's connected to the two CCP ports for oscillator pins on the micro
PICs with PWM output ¦ All port pin terminating in a well labeled
¦ With DIP-28 microcontroller socket Relimate Connector with +Vcc and Gnd
¦ 4 MHz Crystal Resonator connection
¦ 3 User Buttons ¦ Onboard +5V voltage regulator with a diode
¦ PBT for power plug-in bridge to provide any polarity connection to
¦ Onboard +5V voltage regulator with diode the power-in PBT
protection for reverse polarity ¦ Power-On LED indicator
¦ Relimate Connectors for easy connection of ¦ A jumper option given to allow a MCLR/RA3
port pin of the MCU to external interfacing pin to be used as a general purpose Input Pin
¦ 4K EEPROM (24C04) to store valuable data ¦ Four mounting holes of 3.2 mm each
for PIC's without Internal EEPROM ¦ PCB dimensions 80 mm x 71 mm
¦ PBT for supplying 5V regulated supply to
external interface
¦ Infra Red Receiver Sensor for IR related
study or project
¦ Four mounting holes 3.2 of mm each 4 X 4 MATRIX KEYBOARD C004
¦ PCB dimensions 71 mm x 87 mm
4 X 4 Matrix Keyboard kit will add keyboard support to your project.
¦ Matrix style keyboard
4 DIGIT 7-SEGMENT DISPLAY ¦ 4 column X 4 rows
USING 74HC595 C003 ¦ Sturdy 4 pin big tactile switch
¦ 8 Pin well marked Relimate connector for
easy connection
4 Digit 7-Segment Display Using 74HC595 kit drives four 7-Segment
¦ Four mounting holes of 3.2 mm each
common cathode display using Serial Shift Register IC.
¦ PCB dimensions 79 mm x 72 mm
¦ Four 0.5" common cathode display
¦ Input / Output connector for connecting
multiple modules in series
¦ 4 Pins for easy control with Microcontroller
8 RELAY BOARD FOR IR/RF
¦ Four mounting holes of 3.2 mm each
INTERFACE C007
¦ PCB dimensions 116 mm x 53 mm

8 Relay Board for IR/RF Interface kit offers 8 relay output control for
your project.
6 DIGIT 7-SEGMENT ¦ Eight 12V Single Pole Double Throw
MULTIPLEXED DISPLAY C005 (SPDT) relays
¦ Transistor driven control with LED
6 Digit 7-Segment Multiplexed Display kit offers 6 digit common indication
anode/cathode Multiplex Display. ¦ Diode protection for Back EMF generated
¦ 3-Pin PBT connector for easy connection of
¦ 0.5" 7-segment display (common anode or all relay contact pins
common cathode) ¦ PBT connector for easy connection of the
¦ Multiplex style connection of the 7- input power supply
Segments of all the display ¦ Onboard 5V @ 1A regulator IC to source
¦ Individual lines for the common pin of each supply to connecting interfaces
of the segment ¦ 10-Pin well marked relimate connector for
¦ Series resistor for each of the 7 segment ease of connection
of the display to regulate current ¦ Power-On LED indicator
¦ Well marked 14-Pin relimate connector on ¦ Well marked 14-Pin relimate connector on
board for easy connection board for easy connection
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 42 mm x 103 mm ¦ PCB dimensions 101 mm x 110 mm

8 TACT SWITCHES
INPUT BOARD C008 LCD MODULE C013
8 Tact Switches Input Board kit offers 8 key inputs for your project. LCD Module kit offers an easy way of interfacing a 16X2 Alphanumeric
¦ Pull Up resistors to Vcc LCD.
¦ 8-Pin DIP Switch ¦ Interfacing 16X2 backlight alphanumeric
¦ 8 Tactile key input LCD in 4bit mode
¦ Well marked 8-Pin relimate connector on ¦ Onboard resistor to limit current to backlight
board for easy connection LED
¦ Separate 2-Pin Relimate connector for ¦ Preset to adjust the contrast level of the LCD
supply line ¦ 8-Pin relimate connector for easy connection
¦ Four mounting holes of 3.2 mm each of all pins to the microcontroller board
¦ PCB dimensions 38 mm x 84 mm ¦ PCB dimensions 50 mm x 81 mm

sales@anykits.co.in 7 www.anykits.co.in
MICROCONTROLLER/INTERFACE

89C2051 DEVELOPMENT MULTIPURPOSE PIC16F


STICK C010 18-PIN DEVELOPMENT BOARD C015

89C2051 Development Stick kit offers an easy way of interfacing 89C2051 Multipurpose PIC16F 18-Pin Development Board provide you with your
compatible MCU's. prototyping requirement.
¦ Slim design with plug in type approach ¦ ICSP connector for programming for the
¦ Voltage regulator on board for stable and PICs with ICD support
regulated supply to the MCU ¦ 18-Pin IC socket for the microcontroller
¦ RESET switch for resetting the MCU ¦ All port pin terminating in well labeled
¦ 11.0592 MHz Crystal relimate connector with +Vcc and Gnd
¦ 4K external EEPROM connection
¦ Power-On LED for indicator ¦ PBT for Power plug-in
¦ 20-Pin well marked Berg connector for ¦ Onboard +5V Voltage regulator to provide
ease of connection regulated power to the board
¦ Access to all IO pins & supply pin on the ¦ Diode to provide against wrong polarity
Berg connector connection to the board
¦ 20-Pin IC socket for MCU ¦ Power-On LED indicator
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 35 mm x 72 mm ¦ PCB dimensions 54 mm x 54 mm

RS485 CONTROLLED
8 RELAY BOARD C014 RS232 INTERFACE MODULE C019

With RS485 Controlled 8 Relay Board you can control upto 8 SPDT (Single RS232 Interface Module is a simple add-on kit to connect your 5V Serial
Pole Double Throw) relays using a simple RS485 protocol. Data Output to the PC.
¦ Upto 8, 12V SPDT relay control ¦ MAX232 based Level Shifter IC
¦ Industry standard relay drive IC - ULN2803 ¦ Simple and straight forward design
¦ Data received indicator LED ¦ Easy connection via Relimate connector to
¦ LED indicator to display relay state your HOST interface
¦ Power-On LED indicator ¦ Supply provided by the host interface
¦ On board regulator IC ¦ Four mounting holes of 3.2 mm each
¦ PBT type connector for easy connection of ¦ PCB dimensions 40 mm x 33 mm
all wires to the PCB
¦ Simple RS485 Protocol
¦ Can be controlled either by a
microcontroller board or via PC using
suitable RS232 - RS485 converter
¦ Diode protection against reverse polarity
RS232 TO RS485 MODULE C020
connection
¦ NC-C-NO pin outs from each relay into a RS232 to RS485 Module kit will provide you a seamless connection
PBT connector between a PC and an RS485 network.
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 166 mm x 92 mm ¦ Simplex connection of the interface to the
RS485 network
¦ Easy switching mode between Receiver
and Transmitter
¦ Optional 5V regulated supply provision on
RC SIGNAL READER C016 board
¦ 9-Pin, PCB mounted, female type D
connector available
RC Signal Reader will decode the incoming RC Signal on a LCD. ¦ Supply can also be provided by the host
¦ Analyze the incoming RC Signal from and interface via Relimate connectors carrying
RC Receiver data
¦ Power-On LED indicator ¦ Four mounting holes of 3.2 mm each
¦ On board regulator IC ¦ PCB dimensions 64 mm x 43 mm
¦ Clearly marked 8pin relimate connector for
connecting the Decoder PCB to the LCD
module (C013)
¦ Relimate Connector for Power and RC
Signal-in
¦ Resonator based circuit for error free
computation
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 57 mm x 41 mm

sales@anykits.co.in 8 www.anykits.co.in
MICROCONTROLLER/INTERFACE

SINGLE DIGIT BIG DISPLAY


SERIAL PIC PROGRAMMER C021 MODULE USING 74HC595 C022

Serial PIC Programmer kit is a must have for all those who develop, Single Digit Big Display Module Using 74HC595 kit will display large 7-
experiment, program and play with Microchip based PIC projects. segment single digit number, 3.4 inch in height, which can be visible over
large distance. More digits can be connected serially to each other easily.
¦ JDM compatible interface design
¦ ICSP and direct chip level programming ¦ Each segment made up of 5 LEDs
available ¦ Series current limiting resistors provided
¦ ZIF type socket for easy placement and for each segment
removal of the microcontroller ¦ Serial latched type display using SPI
¦ LED indication of programming being done protocol
¦ No power supply needed. May not work on ¦ Separate Relimate type connector for
laptops where the voltage may be below connecting Input/Output
7.3 V ¦ Separate supply pins for data and LED
¦ Zener Diode protected design input
¦ 9-Pin PCB mounted female type D ¦ Four mounting holes of 3.2 mm each
connector provided for PC side connection ¦ PCB dimensions 125 mm x 58 mm
¦ Selector switch for selecting different PIC
type during programming in ZIF socket
¦ Marker points provided on PCB for proper
insertion point of different PIC's in the ZIF RC TO MOTOR CONTROL
socket INTERFACE C025
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 53 mm x 108 mm
RC to Motor Control Interface kit controls a DC motor using an incoming RC
Signal.
¦ Relimate type connector for easy
connection of all wires to this kit
TEMPERATURE READER - LM35 C023 ¦ Requires 5 VDC input from an external
source
¦ Resonator based design for better accuracy
Temperature Reader - LM35 kit displays temperature of the surrounding
¦ Two mounting holes of 3.2 mm each
area an LCD screen. This is not a controller but just a reader.
¦ PCB dimensions 30 mm x 37 mm
¦ LM35 based sensor design
¦ LCD based display (C013)
¦ Voltage regulator for providing regulated
supply on board
¦ PBT type connector for connecting power
4 DIGIT 7-SEGMENT
supply to the board
MULTIPLEX DISPLAY C027
¦ Relimate type connector to connect the
sensor to the Kit and LCD to Kit
¦ Diode protection against reverse polarity
4 Digit 7-Segment Multiplex Display kit will provide 4 digit of multiplexed
connection of power supply display for your project.
¦ Four mounting holes of 3.2 mm each ¦ 5V Supply operation
¦ PCB dimensions 48 mm x 43 mm ¦ 0.5” - CA type display
¦ Switching of power to the display via
switching transistor
¦ Standard Box Header for easy connection
of the board to various development boards
3.3V REGULATOR BOARD C026 or project
¦ Four mounting holes 3.2 mm each
This kit will provide 3.3 V @ 800 mA DC Regulated Supply. The kit based ¦ PCB dimensions 74 mm x 42 mm
on the LM1117 Low-Dropout Linear Regulator.
¦ Input - 5 to 15 VDC
¦ Output - 3.3 V @ 800 mA regulated low
ripple DC voltage A2D CONVERTER BOARD C028
¦ Current limiting and Thermal shutdown
circuit protection (provided by IC feature)
¦ Filter capacitors for low ripple DC output This simple A2D (Analog to Digital) Converter Board can log upto 8 channel
¦ Power Battery Terminal (PBT) for easy of analog signal with 8 bit resolution. This board uses the famous
connection of input and output ADC0808 chip from National Semiconductor.
¦ Four mounting holes of 3.2 mm each ¦ Two standard box type header connector
¦ PCB dimensions 40 mm x 26 mm for easy connection of the board to various
development boards or project
¦ Separate box header for Data and Control
signal for the ADC
¦ PBT type connector for easy connection of
4 BI-COLOUR LED BOARD C033 Analog signal input or sensor connection to
the board
4 Bi-Colour LED board provides a simple visual indication to any ¦ +5 VDC and Gnd connection available for
application which you may require. sourcing supply for your sensor or add-on
interface or signal conditioner board
¦ Interfacing via box header type connector
¦ On board oscillator source for the analog to
¦ Jumper selectable common anode or
digital converter
common cathode mode ¦ Four mounting holes 3.2 mm each
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 54 mm x 63 mm
¦ PCB dimensions 44 mm x 37 mm

sales@anykits.co.in 9 www.anykits.co.in
MICROCONTROLLER/INTERFACE

60 SEC RECORD/PLAYBACK AT89Sxx DEVELOPMENT


MODULE C029 BOARD C030

60 Sec Record/Playback Module kit will playback and record upto 60 Our AT89Sxx Development Board provides a very simple and cost effective
seconds of voice message. This kit is an excellent choice to add voice to platform for prototyping solution. The compact design provides
your project. connection to all the pins of the microcontroller for the user.
¦ Upto 60 Seconds of non volatile voice ¦ Prototyping solution available for 40-pin
storage AT89xx series microcontroller from ATMEL
¦ Upto eight segments record and play ¦ All the four ports available to the user via
option available standard 10 pin box header with supply of
¦ Trigger inputs and supply source available 5 VDC for interfacing circuits
to the board via standard box header ¦ ISP (In circuit Serial Programming)
connector connector available for chips with ISP
¦ Standard audio amplifier capable of support
delivering upto 350 mW of audio ¦ 11.0592 MHz crystal on board
amplification with Volume adjust preset ¦ Pull-up resistor network for Port 0 of the
¦ Jumper selectable mode option microcontroller
¦ Jumper enabled record option ¦ UART level shifter circuit using MAX232 IC,
¦ Reset switch available for use in Tape on board for easy connection of the board
mode to the RS232 devices
¦ Onboard MIC capsule for recording ¦ Jumper selectable connection available for
message directly onto the chip connecting the UART level Shifter to the
¦ Flashing LED to display Record / Playback port pins
of messages ¦ On board voltage regulator available for
¦ Speaker Connection via PBT Connector sourcing regulated 5V @ upto 1A voltage to
¦ 5 VDC Power Supply required the board and connecting circuit
¦ Preset for adjusting sampling rate, record ¦ Power-On LED indicator
level and Volume Level of voice record/play ¦ AUX Power source of 5 VDC available on a
¦ 28-pin IC socket for the main IC PBT connector for sourcing DC supply to
¦ Four mounting holes of 3.2 mm each interfacing circuits
¦ PCB dimensions 50 mm x 88 mm ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 74 mm x 97 mm

ATmega8 DEVELOPMENT
BOARD C031 ATmega16/32 DEVELOPMENT
BOARD C032
Our ATmega8 Development Board provides a very simple and cost
effective platform for prototyping solution. The compact design provides Our ATmega16/32 Development Board provides a very simple and cost
connection to all the pins of the microcontroller for the user. effective platform for prototyping solution. The compact design provides
connection to all the pins of the microcontroller for the user.
¦ Prototyping solution available for 28-pin
ATmega series AVR microcontroller from ¦ Prototyping solution available for 40-pin
ATMEL ATmega series AVR microcontroller from
¦ All the three ports available to the user via ATMEL
standard 10 pin box header with supply of ¦ All the four ports available to the user via
5 VDC for interfacing circuits standard 10 pin box header with supply of
¦ Onboard reset switch for easy reset of the 5V DC for interfacing circuits
microcontroller ¦ Onboard reset switch for easy reset of the
¦ ISP (In circuit Serial Programming) microcontroller
connector available for chips with ISP ¦ ISP (In circuit Serial Programming)
support connector available for chips with ISP
¦ 8 MHz crystal on board support
¦ UART level shifter circuit using MAX232 IC, ¦ 8 MHz crystal on board
on board for easy connection of the board ¦ UART level shifter circuit using MAX232 IC,
to the RS232 devices on board for easy connection of the board
¦ Jumper selectable connection available for to the RS232 devices
connecting the UART level Shifter to the ¦ Jumper selectable connection available for
port pins connecting the UART level Shifter to the
¦ On board voltage regulator available for port pins
sourcing regulated 5V @ upto 1A voltage to ¦ On board voltage regulator available for
the board and connecting circuit sourcing regulated 5V @ upto 1A voltage to
¦ Power-On LED indicator the board and connecting circuit
¦ AUX Power source of 5 VDC available on a ¦ Power-On LED indicator
PBT connector for sourcing DC supply to ¦ AUX Power source of 5 VDC available on a
interfacing circuits PBT connector for sourcing DC supply to
¦ Four mounting holes of 3.2 mm each interfacing circuits
¦ PCB dimensions 60 mm x 89 mm ¦ Four mounting holes of 3.2 mm
¦ PCB dimensions 64 mm x 101 mm

PROTOTYPE BOARD C034

Prototype Board is a simple PCB offering easy


connection of a standard 10-pin Box Header
connector to prototyping area.
PCB dimensions 96 mm x 56 mm

sales@anykits.co.in 10 www.anykits.co.in
MICROCONTROLLER/INTERFACE

8 WAY DIP SWITCH BOARD C035 IN/OUT CONNECTION BOARD C036

8 Way DIP Switch Board is a simple PCB In/Out Connection Board is a simple PCB
offering easy connection of a standard 10-pin offering easy connection of a standard 10-pin
Box Header connector to a 8 way DIP Switch Box Header connector to PBT or 8-pin Relimate
with a jumper selectable pull-up / pull down of connector. This PCB also has an AUX power
resistor network connected in parallel. PBT through which you can either source or
PCB dimensions 32 mm x 37 mm supply power to your projects.
PCB dimensions 39 mm x 58 mm

8 SWITCH INPUT BOARD C037 RS232 TO RS485 BOARD (R) C038

8 Switch Input Board is a simple PCB offering RS232 to RS485 Board (R) provides a seamless connection of the PC to
easy connection of a standard 10-pin Box an RS485 network.
Header connector to 8 small type Tactile Switch
with a jumper selectable pull-up / pull down of ¦ Simplex connection of this interface to the
resistor network connected in parallel. RS485 network
PCB dimensions 37 mm x 87 mm ¦ Easy way of switching the modes between
Receiver and Transmitter
¦ 5 V regulated supply provision on board
¦ 9-pin, PCB mounted, Female type D-
connector available
¦ Supply can also be provided by the host
DTMF DEVELOPMENT BOARD C039 interface via relimate connector carrying
data
¦ Four mounting holes 3.2 mm each
DTMF Development Board offers a very convenient way to generate DTMF ¦ PCB dimensions 82 mm x 33 mm
tones and demodulate it. It uses the famous MT8880/MT8888 DTMF
transreceiver IC from Mitel.
¦ Easy 10 pin Box Header connector for
interfacing data/control pins EEPROM ADD-ON BOARD C040
¦ Crystal derived frequency source for
accurate generation and demodulation of
DTMF tones for your project EEPROM Add-On Board offers an easy way to interface a standard 24Cxx
¦ Onboard upto 350 mW audio amplifier type I2C EEPROM to your project.
block for DTMF tones with Volume Adjust
¦ 5 VDC supply sourced through the
Preset
interfacing Box Header connector
¦ 5V Supply sourced via interfacing Box
¦ Jumper selectable address option available
Header
¦ Four mounting holes 3.2 mm each
¦ Relimate/Berg type analog connection
¦ PCB dimensions 36 mm x 32 mm
¦ Four mounting holes 3.2 mm each
¦ PCB dimensions 56 mm x 49 mm

GLCD ADAPTER BOARD C041


I/O EXPANDER BOARD C042
Our simple GLCD Adapter Board offers an easy way to interface a standard
GLCD to your project. I/O Expander Board offers a convenient way to interface upto 16 I/O pins
¦ 5 VDC supply sourced through the in your project using SPI/I2C bus. This kit uses the famous MCP23x17 IO
interfacing Box Header connector chip from Microhip.
¦ Two separate box header connector ¦ Supply sourced through the interfacing Box
available for interfacing of data bus and Header connector
control bus to the interfacing unit ¦ The kit has 2 separate Box Header type
¦ Contrast control preset also available connector for the 16 pins of I/O port and 1
¦ PCB dimensions 53 mm x 33 mm Box Header for interfacing of the PCB with
the host controlling circuit
¦ Jumper selectable address option is also
available for this kit
¦ Four mounting holes 3.2 mm each
¦ PCB dimensions 58 mm x 54 mm

LCD ADAPTER BOARD C043

Our simple LCD Adapter Board offers an easy way to interface a standard
16X2 LCD to your project.
¦ Supply sourced through the interfacing Box
Header connector
¦ Interfacing is via standard box header
connector
¦ Contrast control preset also available
¦ PCB dimensions 42 mm x 24 mm

sales@anykits.co.in 11 www.anykits.co.in
MICROCONTROLLER/INTERFACE

8 LED OUTPUT BOARD 8 LED OUTPUT BOARD


- SINK C044 - SOURCE C045

This simple 8 LED Output Board - Sink, offers a convenient way to monitor This simple 8 LED Output Board - Source, offers a convenient way to
or display output of various I/O pins for your project. monitor or display output of various I/O pins for your project.
¦ Interfacing is via 10-pin Box Header ¦ Interfacing is via 10-pin Box Header
connector connector
¦ Four mounting holes 3.2 mm each ¦ Four mounting holes 3.2 mm each
¦ PCB dimensions 75 mm x 23 mm ¦ PCB dimensions 75 mm x 23 mm

4 X 4 MATRIX KEYBOARD C046 OPTO-ISOLATED I/O BOARD C047

4 X 4 Matrix Keyboard kit will add keyboard support to your project. Opto-Isolated I/O Board offers a compact & convenient way to interface
industrial type inputs/outputs to your microcontroller boards, Signal
¦ Matrix style keyboard 4 Column X 4 Rows
transmission between circuits of different potentials and impedances etc.
¦ Sturdy 4-pin big Tactile Switch
¦ Box Header connector for easy connection ¦ 4 optoisolated inputs & 4 optoisolated
¦ Four mounting holes 3.2 mm each outputs
¦ PCB dimensions 59 mm x 63 mm ¦ Std TTL input signals for opto-couplers
¦ Interfacing is via 10-pin Box Header and
Power Battery Terminal (PBT) type
connector
¦ Power source LED indicator
¦ Four mounting holes 3.2 mm each
PIC16F 28/40-PIN
DEVELOPMENT BOARD C048 ¦ PCB dimensions 54 mm x 64 mm

PIC16F 28/40-pin Development Board will help you with your prototyping
requirement with any of Microchip's 28/40-pin of 16F PIC microcontrollers. PIC16F 18-PIN DEVELOPMENT
BOARD C049
¦ All ports terminating in separate box
header with 5 VDC source option
¦ ICSP connector for programming for the PIC16F 18-pin Development Board will help you with your prototyping
PIC's with ICD support requirement with any of Microchip's 18 pin of 16F PIC microcontrollers.
¦ Jumper selectable on board pull up resistor
¦ All ports terminating in separate box
for PortA.4 pin on the microcontroller
header with 5 VDC source option
¦ Bridge in the input provides any polarity
¦ ICSP connector for programming for the
DC supply connection to the board
PIC's with ICD support
¦ 20 MHz crystal source
¦ Jumper selectable on board pull up resistor
¦ Onboard +5V Voltage regulator
for PortA.4 pin on the microcontroller
¦ Four mounting holes of 3.2 mm each
¦ Bridge in the input provides any polarity
¦ PCB dimensions 77 mm x 82 mm
DC supply connection to the board
¦Jumper selectable 20 MHz crystal source
¦Onboard +5V Voltage regulator
¦Four mounting holes of 3.2 mm each
4 DIGIT 7-SEGMENT DISPLAY
USING 74HC595 (R) C050 ¦PCB dimensions 56 mm x 55 mm

4 Digit 7-Segment Display using 74HC595 (R) kit drives four 7-Segment
common cathode display using Serial Shift Register IC. 6 DIGIT 7-SEGMENT
MULTIPLEXED DISPLAY (R) C051
¦ Four 0.5" common cathode display
¦ Input / Output Box type connector for
connecting multiple modules in series 6 Digit 7-Segment Multiplexed Display (R) kit offers 6 digit common
¦ 4 Pins for easy control with microcontroller anode/cathode multiplex display.
¦ Four mounting holes 3.2 mm each
¦ 0.5" 7-segment display (Common anode or
¦ PCB dimensions 94 mm x 56 mm
Common cathode)
¦ Multiplex style connection of the 7-
Segments of all the display
¦ Individual lines for the common pin of each
of the segment
RS232 OR RS485 BOARD C052 ¦ Series resistor for each of the 7 segment
of the display to regulate current
¦ Easy connection of the PCB to interfacing
RS232 or RS485 Board will help you provide a seamless connection of circuit via Box Header connector
either of the protocol RS232 or RS485 with your interfacing circuit. ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 84 mm x 47 mm
¦ 5 VDC Supply sourced through the Box
Header interfacing connector
¦ Either of the two communication protocol
available by use of individual IC on the PCB
¦ PBT type connector for connection of the
RS485 link cable and 9 pin female type D
connector for interfacing of UART signals to
the PC
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 38 mm x 61 mm

sales@anykits.co.in 12 www.anykits.co.in
MICROCONTROLLER/INTERFACE

RTC ADD-ON BOARD C053 4 SERVO CONTROLLER BOARD C054

RTC Add-On Board offers an easy way to interface a standard I2C RTC IC Our 4 Servo Controller Board is a solution for controlling upto 4 Servos via
type DS1307, into your project. onboard preset or potentiometer.
¦ 5 VDC supply sourced through the ¦ Microcontroller based design for greater
interfacing Box Header connector flexibility and ease of control
¦ Battery backup for the RTC board available ¦ Individual servo controlled via onboard
on the PCB preset or external potentiometer
¦ Four mounting holes of 3.2 mm each ¦ PBT connector for easy connection of the
¦ PCB dimensions 50 mm x 33 mm input power supply
¦ Berg connector for connection of Servos
¦ Power-On LED indicator
¦ Four mounting holes of 3.2 mm each
UNIPOLAR 4-PHASE STEPPER ¦ PCB dimensions 57 mm x 65 mm
MOTOR CONTROLLER BOARD C055

Unipolar 4-Phase Stepper Motor Controller Board will help you control a
PIC18F USB DEVELOPMENT
Stepper Motor or 4 individual Solenoids.
BOARD C056
¦ Box Header connector provides for easy
interfacing option
PIC18F USB Development Board will help you with your prototyping
¦ Separate LED indicator for individual Phase
requirement with any 28/40-pin Microchip supporting USB interface
¦ Power Battery Terminal (PBT) for easy
microcontrollers.
connection of output load and power
¦ Power-On LED indicator ¦ All ports terminating in separate Box
¦ Four mounting holes of 3.2 mm each Header with 5 VDC source option
¦ PCB dimensions 86 mm x 49 mm ¦ ICSP connector for programming for the
PIC's with ICD support
¦ Bridge in the input provides any polarity
DC supply connection to the board
¦20 MHz crystal source
8 SERVO ADAPTER BOARD C057 ¦Onboard +5V Voltage regulator
¦Four mounting holes of 3.2 mm each
¦PCB dimensions 77 mm x 87 mm
8 Servo Adapter Board is a small board which offers connection interface to
upto 8 servo's via a standard Box Header connector.
¦ Power supply for the servos is sourced via
separate onboard PBT connector with LED
indicator
¦ Well marked Berg connector for connecting
servos
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 60 mm x 25 mm

sales@anykits.co.in 13 www.anykits.co.in
TEST & MEASUREMENT

AA/AAA BATTERY VOLTAGE


TESTER D001 0 - 10V LED VOLTMETER D002

AA/AAA Battery Voltage Tester is a simple, easy and cheap kit to test and 0 - 10V LED Voltmeter kit is an easy and cheap kit to instantly visualize
visualize the voltage of AA and AAA type batteries commonly available in audio signal level. This kit is based on the famous LM3914 IC from National
the market. This kit is based on the famous LM3914 IC from National Semiconductor.
Semiconductor.
¦ Input - 12 VDC @ 100 mA
¦ Input - 5 VDC ¦ Output - 10 LED's
¦ Output - 10 LED's ¦ 2 Types of display - Bar and Dot selectable
¦ 2 Types of display - Bar and Dot selectable by a jumper
by a jumper ¦ Very low current consumption, typical
¦ Very low current consumption, typical 100mA
100 mA ¦ Berg pins for connection of power and
¦ Berg pins for connecting power and voltage in
voltage in ¦ Four mounting holes of 3.2 mm each
¦ Four mounting holes of 3.2 mm each ¦ PCB dimensions 31 mm x 74 mm
¦ PCB dimensions 34 mm x 74 mm

12V LEAD ACID BATTERY


VARIABLE RANGE LED MONITOR D005
VOLTMETER D003
12V Lead Acid Battery Monitor is a simple kit which tells you the voltage of
Variable Range LED Voltmeter kit is a simple and cheap way of visually your Lead Acid battery visually with the help of 10 LED's. This kit is based
displaying voltage of a given source with the help of 10 LED's. This kit is on the famous LM3914 IC from National Semiconductor.
based on the famous LM3914 IC from National Semiconductor.
¦ Input - 15 VDC Max
¦ Input - 12 VDC @ 190 mA ¦ Maximum and Minimum range selectable
¦ Range - 0 - 1.3 V and 0 - 10.8 V with onboard preset
adjustable with onboard preset ¦ Output - 10 LED's
¦ Output - 10 LED's ¦ 2 Types of display - Bar and Dot selectable
¦ 2 Types of display - Bar and Dot selectable by a jumper
by a jumper ¦ Very low current consumption, typical
¦ Very low current consumption, typical 100 mA
100 mA ¦ Berg pins for connecting power / voltage in
¦ Berg pins for connecting power and ¦ Four mounting holes of 3.2 mm each
voltage in ¦ PCB dimensions 37 mm x 75 mm
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 32 mm x 74 mm

CURRENT SENSE SWITCH D007


0 - 20V LED VOLTMETER D006
Current Sense Switch kit is a simple circuit which will operate a relay when
a preset current is reached / exceeded. This circuit can offer over current
0 - 20V LED Voltmeter kit displays the voltage of the source using 20 LED's. protection to your project. You can connect various alarm output or simply
This kit is based on the famous LM3914 IC from National Semiconductor. break the supply to the circuit using the relay.
¦ Input - 5 VDC Max @ 30 mA in DOT mode ¦ Input - 5 VDC Max @ 30 mA in DOT mode
and 300 mA in BAR mode and 300 mA in BAR mode
¦ Range selectable with onboard preset ¦ Range - 1 ~ 2 A selectable with onboard
¦ Output - 20 LED's preset
¦ 2 Types of display Bar and Dot selectable ¦ Output - SPDT Relay
by a jumper ¦ Power Battery Terminal (PBT) and Terminal
¦ Berg pins for connecting power / voltage in Pins for easy connection
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 40 mm x 145 mm ¦ PCB dimensions 49 mm x 60 mm

SINEWAVE GENERATOR D008 PULSE GENERATOR D009

Sinewave Generator kit will provide you with a Sinusoidal Waveform Pulse Generator kit will generate a frequency in KHz which can form a good
output to test various instruments. You can also use the High quality test gear project. This kit is based on the classic LM555 timer IC.
output from this kit to insert a tone modulation in your audio and RF
equipment. This kit is designed using XR2206 IC to provide High Stability ¦ Input - 12 VDC Max @ 40 mA
and Accuracy. ¦ Range - jumper selectable and preset
tunable range of 1 Hz to 180 KHz
¦ Input - 12 VDC Max @ 50 mA ¦ Power-On LED indicator
¦ Range - Jumper selectable and preset ¦ Terminal pins for easy connection
tunable range of 10 Hz - 100 KHz ¦ Four mounting holes of 3.2 mm each
¦ Output Level can be controller with ¦ PCB dimensions 40 mm x 47 mm
onboard preset
¦ Power-On LED indicator
¦ Power Battery Terminal (PBT) for easy
connection
¦ PCB dimensions 52 mm x 58 mm

sales@anykits.co.in 14 www.anykits.co.in
TEST & MEASUREMENT

LED PANEL METER D010 LUX METER MODULE D011

LED Panel Meter kits which accept a single-ended input to display many LUX Meter Module kit has been design to measure the illumination.
parameters including voltage, current, temperature, pressure etc. Illumination is luminas flux falling on surface area of photo diode. This
illumination converted to corresponding voltage using Op-Amp circuit.
¦ Supply input 5 VDC, single supply
operation ¦ Supply 9 VDC PP3 Battery @ 20 mA
¦ Maximum range is 0 - 199.9 mV ¦ Onboard Photo Diode
¦ Decimal point position is selectable via ¦ Onboard preset for calibration
jumper ¦ Range selection via jumper
¦ Berg connector for connecting supply input ¦ Interfacing is via berg connector
and signal in ¦ Power-On LED indicator
¦ PCB dimensions 73 mm x 55 mm ¦ PCB dimensions 54 mm x 38 mm

sales@anykits.co.in 15 www.anykits.co.in
TIMER & CONTROLLER

LONG DURATION TIMER E001 ELECTRONIC TOGGLE SWITCH E002

Long Duration Timer kit can be used for all application requiring a delay of Electronic Toggle Switch kit can be used for switching On/Off application of
upto 2 Hours. This kit is built around digital gates and 4020 IC. home appliances like fan, light etc.
¦ Input - 12 VDC ¦ Input - 12 VDC
¦ Onboard Start Switch ¦ Onboard ON/OFF switch
¦ Relay output - SPDT relay ¦ Relay output - SPDT relay
¦ Relay specification - 5 A @ 250 VAC ¦ Relay specification - 5 A @ 250 VAC
¦ Relay state LED indicator ¦ Relay state LED indicator
¦ Range upto 2 Hours, jumper selectable and ¦ Power-On LED indicator
preset adjustable ¦ Power Battery Terminal (PBT) for easy
¦ Power-On LED indicator relay output connection
¦ Power Battery Terminal (PBT) for easy ¦ Terminal pins for supply connection
relay output connection ¦ Four mounting holes of 3.2 mm each
¦ PCB Mounted ON/OFF slide switch ¦ PCB dimensions 46 mm x 58 mm
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 49 mm x 86 mm

LIGHT / DARK SENSITIVE


SWITCH E004
1 SEC TO 100 SEC TIMER E003
Light / Dark Sensitive Switch kit is a simple project which operates a relay
when the light falling on the LDR goes below or goes above a set point.
1 Sec To 100 Sec Timer kit can be used for all application requiring a delay
¦ Input - 12 V @ 50 mA
of upto 100 Seconds. This kit is built around the famous 555 timer IC.
¦ Relay output - SPDT relay
¦ Input - 12 VDC @ 100 mA ¦ 2-in-1 kit, either as light sensitive kit or
¦ Onboard start and reset tactile switch dark sensitive switch
¦ Relay output - SPDT relay ¦ Onboard preset to set the level
¦ Relay specification - 5 A @ 250 VAC ¦ Power-On LED indicator
¦ Relay state LED indicator ¦ Relay On LED indicator
¦ Preset adjustable range function ¦ Power Battery Terminal (PBT) for easy
¦ Power-On LED indicator relay output connection
¦ Power Battery Terminal (PBT) for easy ¦ Four mounting holes of 3.2 mm each
relay output connection ¦ PCB dimensions 50 mm x 54 mm
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 48 mm x 63 mm

60 SEC TIMER E006


CLASSIC AC 230V TIMER E005
60 Sec Timer kit can be used in all application requiring a delay of upto 60
Seconds. This is based on the Classic 555 Timer IC.
Classic AC 230 V Timer kit can be used in all application requiring a delay of
¦ Input - 12 VDC @ 56 mA
upto 3 Minutes to operate or control any AC mains load of upto 200 Watts.
¦ Onboard start switch
This is based on the Classic 555 Timer IC, triggering a TRIAC. Input and
¦ Relay output - SPDT relay
Output is Optically Isolated.
¦ Relay specification - 5 A @ 250 VAC
¦ Input - 12 VDC ¦ Relay state LED indicator
¦ Output - upto 200 Watts ¦ Preset adjustable range function
¦ Optically isolated Input / Output ¦ Power-On LED indicator
¦ Onboard start and reset tactile switch ¦ Power Battery Terminal (PBT) for easy
¦ Timer On LED relay output connection
¦ Preset adjustable and jumper selectable ¦ Four mounting holes of 3.2 mm each
for range ¦ PCB dimensions 44 mm x 56 mm
¦ Power-On LED indicator
¦ Power Battery Terminal (PBT) for easy
relay output connection
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 46 mm x 91 mm CYCLIC TIMER E009

Cyclic Timer kit can be used in all applications requiring a cyclic On/Off
condition of the relay. This kit is ideal for use in flashing of a light bulb,
POWER-ON DELAY SWITCH E007 buzzer or siren application.
¦ Input - 12 VDC
¦ Relay output - SPDT relay
Power-ON Delay Switch which can be used in all applications requiring a
¦ Relay specification - 5 A @ 250 VAC
delay during power-on from 10 seconds onwards.
¦ Relay state LED indicator
¦ Input - 12 VDC ¦ Preset adjustable range function
¦ Relay output - SPDT relay ¦ Power-On LED indicator
¦ Relay specification - 5 A @ 250 VAC ¦ Power Battery Terminal (PBT) for easy
¦ Preset adjustable range function relay output connection
¦ Power-On LED indicator ¦ Four mounting holes of 3.2 mm each
¦ Power Battery Terminal (PBT) for easy ¦ PCB dimensions 44 mm x 58 mm
relay output connection
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 42 mm x 45 mm

sales@anykits.co.in 16 www.anykits.co.in
TIMER & CONTROLLER

LIGHT SENSITIVE SWITCH E010 DARK SENSITIVE SWITCH E011

Light Sensitive Switch is a simple project which operates a relay when the Dark Sensitive Switch is a simple project which operates a relay when the
light falling on the LDR goes above a set point. light falling on the LDR goes below a set point. This circuit is built using
CA3140 Op-amp and can also be considered for use in energy saving
¦ Input - 12 VDC @ 50 mA
application.
¦ Relay output - SPDT relay
¦ Onboard preset to set the level ¦ Input - 12 V @ 50 mA
¦ Relay On LED indicator ¦ Relay output - SPDT relay
¦ Power Battery Terminal (PBT) for easy ¦ Onboard preset to set the level
relay output connection ¦ Relay On LED indicator
¦ Four mounting holes of 3.2 mm each ¦ Power Battery Terminal (PBT) for easy
¦ PCB dimensions 44 mm x 51 mm relay output connection
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 44 mm x 51 mm

TEMPERATURE SENSITIVE
SWITCH E012

Temperature Sensitive Switch is a simple project which operates a relay 10 EVENT PROGRAMMABLE
when the temperature in a particular area goes above a set point. This TIMER USING DS1307 RTC E014
circuit is built using CA3140 Op-amp and NTC temperature Sensor.
¦ Input - 12 VDC @ 50 mA 10 Event Programmable Timer Using DS1307 RTC is a versatile alarm kit
¦ Range - 30 °C to 60 °C with battery backup clock circuit. It can set upto 10 alarms to trigger in a
¦ Relay output - SPDT relay day with single or dual output available for interfacing.
¦ Onboard preset to set the level ¦ Upto 10 settable alarms in a day
¦ Relay On LED indicator ¦ Dual output available for interfacing. A
¦ Power Battery Terminal (PBT) for easy relay output available for 1 second on
relay output connection trigger and upto 8 selectable high outputs
¦ Four mounting holes of 3.2 mm each available for further interfacing to the
¦ PCB dimensions 51 mm x 50 mm outside world
¦ Easy setup of alarm and time via 3 tactile
switches available on the PCB
¦ Power and Relay On LED indicator
¦ Battery backed up clock module
TEMPERATURE CONTROLLER
USING PIC MCU E017 ¦ 16x2 backlight LCD for easy display of time
and status of the working project
¦ PBT type connector for connecting supply
Temperature Controller Using PIC MCU is a utility Temperature Controller and relay output to the PCB
kit for use with a LM35 based temperature sensor with 2 relay outputs. ¦ 12V SPDT (Single Pole Double Throw) relay
This is a simple Microcontroller based design using inbuilt ADC to read the for alarm use
temperature sensor connected to it. Two relay outputs trigger either an ¦ Onboard regulator for regulated supply to
alarm or control an interface connected to it when either the Low or High the kit
set temperature set is reached. ¦ Crystal resonator based design for better
accuracy
¦ Microcontroller based design for greater
¦ AUX PWR (Auxiliary Power) available to
accuracy and control
supply 5V regulated DC supply to other
¦ Relimate type sensor input.
interfaces connected to this kit
¦ LCD type display to display the current
¦ IC sockets for the IC's used in the kit
activity of the kit or menu in configuration
¦ Four mounting holes of 3.2 mm each
mode.
¦ PCB dimensions 94 mm x 61 mm
¦ Two 12V SPDT (Single Pole Double Throw)
relay for alarm/control use
¦ Individual relay out for Low and High alarm
set
2 DIGIT COUNT DOWN
¦ Simple set/configuration available via 3
TIMER E015
tactile switches on the PC
¦ EEPROM backup for alarm setting
¦ Power and Relay On LED indicator 2 Digit Count Down Timer is a utility Count Down timer kit for upto 99
¦ PBT type connector for connecting supply seconds of countdown time. This kit can find many uses in your shack and
and relay output to the PCB home. The relay output remains on during the Count Down period,
¦ Onboard regulator for regulated supply to allowing you to interface load or alarm that you want to keep it on for a
the kit certain amount of time (in seconds).
¦ Crystal resonator based design for better
¦ Microcontroller based design for greater
accuracy accuracy and control
¦ IC sockets for the IC's used in the kit
¦ Two - 0.5" display segments to display
¦ Four mounting holes of 3.2 mm each
time
¦ PCB dimensions 69 mm x 91 mm
¦ 12V SPDT (Single Pole Double Throw)
relay for alarm use
¦ Single key start and dual key alarm time
set function
¦ Power and Relay On LED indicator
¦ PBT type connector for connecting supply
and relay output to the PCB
¦ Onboard regulator for regulated supply to
the kit
¦ Crystal resonator based design for better
accuracy
¦ PCB dimensions 72 mm x 81 mm

sales@anykits.co.in 17 www.anykits.co.in
LIGHT EFFECTS

LIGHT DIMMER F001 WHITE LED LAMP F002

Light Dimmer kit is a low cost dimmer circuit for adjusting the light White LED Lamp (230 VAC), is a kit which can be used as a Night Lamp in
brightness of incandescent, Halogen Lamp, Light Bulb upto 250 W. houses working on direct 230 VAC.
¦ Input supply - 230 VAC ¦Input supply - 230 VAC
¦ Output - 250 W ¦Output - 4 white LEDs
¦ Triac controlled ¦Small size, low current consumption
¦ On board POT for adjusting level ¦Power Battery Terminal (PBT) for easy input
¦ Power Battery Terminal (PBT) for easy 230 VAC mains connection
input / output connection ¦Four mounting holes of 3.2 mm each
¦ Four mounting holes of 3.2 mm each ¦PCB dimensions 37 mm x 46 mm
¦ PCB dimensions 40 mm x 34 mm

LED ARROW CHASING STROBE KIT F004


INDICATOR F003
Strobe Kit will help you drive your flash tube for use in your favorite
LED Arrow Chasing Indicator kit can be used to display a light arrow to lighting application. Some of the application areas are dynamic effect for
show direction. disco parties, photographic special effect, to attract attention.
¦ Input supply - 9 VDC ¦ Input supply - 230 VAC
¦ Output - arrow symbol made with LEDs ¦ Onboard POT to adjust flash frequency
¦ Battery operated low current consumption ¦ Power Battery Terminal (PBT) for easy
¦ Terminal pins for connecting input supply input 230 VAC mains and flash tube
¦ Four mounting holes of 3.2 mm each connection
¦ PCB dimensions 45 mm x 86 mm ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 49 mm x 92 mm

4 LED FLASHER F005 LASER DIODE DRIVER F006


4 LED Flasher kit simply flashes a set of 4 LED's to attract attention.
Laser Diode Driver kit will help you safely drive (constant current) a 3 mW
¦ Power supply - 9 V (PP3) visible Laser Diode for your application.
¦ PCB dimensions 28 mm x 44 mm
¦ Input supply - 6 VDC
¦ Onboard preset to adjust the current flow
to the Laser Diode
¦ Power-On LED indicator
¦ Relimate connector for easy input supply
and LASER DIODE module connection
¦ PCB dimensions 37 mm x 42 mm

18 LED MULTIPLEXED CHASER F007

18 LED Multiplexed Chaser is a simple and fun loving kit which can be used
to attract attention in a area. 10 LED CHASER F008
¦ Input supply - 9 ~ 12 VDC @ 17 mA
current 10 LED Chaser is a simple kit which can be used to attract attention in an
¦ 6 X 3 LEDs to create a chasing sequence of area.
first row to last row and back
¦ Input supply - 9 ~ 12 VDC @ 20 mA
¦ Onboard preset to adjust the speed of
Current
chaser
¦ Onboard preset to adjust the speed of
¦ 2 PCB project
chaser
¦ PCB dimensions 38 mm x 70 mm
¦ 2 PCB project
¦ PCB dimensions 46 mm x 65 mm

200W LAMP FLASHER F009

200W Lamp Flasher kit is used to flash lamps, bulbs and halogen lamp to
give your product that attracting look.
DARK SENSITIVE SWITCH F010
¦ Input supply - 6 ~ 12 VDC
Dark Sensitive Switch kit switches a load connected to it when night falls.
¦ Output - upto 200 W lamp / bulb load
It could be used as an automatic street light application.
¦ Optically isolated Mains supply
¦ Onboard preset to adjust the frequency ¦ Input supply - 240 VAC
(speed) of flashing (1 Hz to 5 Hz) ¦ Output - upto 200 W Lamp / Bulb load
¦ Power Battery Terminal (PBT) for easy ¦ Small size PCB
input 230 VAC mains and load connection ¦ Power Battery Terminal (PBT) for easy
¦ Terminal pins for connecting DC power connection of input 230 VAC Mains and
supply Load
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 36 mm x 68 mm ¦ PCB dimensions 37 mm x 49 mm

sales@anykits.co.in 18 www.anykits.co.in
LIGHT EFFECTS

30 LED CHASER F011 SOLID STATE RELAY SWITCH F012

30 LED Chaser is a simple kit which can be used to attract attention in an Solid State Relay Switch is a simple kit which will help you control (ON /
area. OFF) a single high power circuit from a low power drive.
¦ Input supply - 9 ~ 15 VDC @ 25 mA ¦ Load - 24 to 240 VAC @ 500 W
Current ¦ Trigger voltage - 2 to 5 VDC (TTL) @
¦ Onboard preset to adjust the speed of 10 mA
chaser ¦ Input isolated with use of Optocoupler
¦ 2 PCB project ¦ Power Battery Terminal (PBT) for easy
¦ Terminal pins for connecting DC power input 230 VAC mains and load connection
supply ¦ Terminal pins for connecting input trigger
¦ PCB dimensions 46 mm x 63 mm signal
¦ Heatsink for TRIAC
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 29 mm x 74 mm

5 LAMP DISCO LIGHTS F013

5 Lamp Disco Lights is very similar to our J009 kit with the difference of
MICRO BASED RUNNING
being able to light bulbs with the use of Triac.
LIGHT CONTROLLER F014
¦ Power supply Input - 6 ~ 12 VDC
¦ Output - 240 VAC @ 100 W each
Micro Based Running Light Controller kit will attract attention by way of
¦ Jumper selectable audio source
running light effect using 8 bulbs. An ideal project for use during festival
¦ Input / Output isolated with use of
lighting, auspicious occasions at home or social gathering events.
Optocoupler
¦ Onboard preset to adjust audio level to the ¦ Microcontroller based design for greater
IC flexibility and ease of control
¦ On board MIC capsule with preamp ¦ Triac based switching of loads connected to
¦ Terminal pins for connecting DC power the circuit
supply ¦ Industry standard isolation with the help of
¦ Power Battery Terminal (PBT) for easy Opto enabled Triac Control
input 230 VAC mains and load connection ¦ Fuse protection for AC output
¦ Four mounting holes of 3.2 mm each ¦ Simple and easy to use 3 tactile switch
¦ PCB dimensions 69 mm x 107 mm enabled control of the kit
¦ PBT type connector for connecting supply
(AC/DC) and TRIAC output on the PCB
¦ Onboard regulator for regulated supply to
the kit
¦ Diode protection for reverse polarity
connection of DC supply to the PCB
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 86 mm x 173 mm

sales@anykits.co.in 19 www.anykits.co.in
POWER SUPPLY

5V/1A REGULATED 5V/3A REGULATED


POWER SUPPLY G001 POWER SUPPLY G002

This kit will provide 5 V @ 1 Amp DC Regulated Supply. The kit is based on This kit will provide 5 V @ 3 Amp DC Regulated Supply. The kit is based on
the famous 7805 voltage regulator in TO220 package. the famous 7805 voltage regulator in TO3 package.
¦ Input - 7 - 18 VAC/DC ¦ Input - 7 - 18 VAC/DC
¦ Output - 5 V @ 1 A regulated low ripple DC ¦ Output - 5 V @ 3 A regulated low ripple DC
voltage voltage
¦ Onboard bridge rectifier to convert AC to ¦ Heatsink for regulator IC
DC ¦ Onboard bridge rectifier to convert AC to
¦ Thermal overload/short circuit protection DC
(provided by IC feature) ¦ LED indication for output
¦ Power Battery Terminal (PBT) for easy ¦ Thermal overload/short circuit protection
input and output connection (provided by IC feature)
¦ Filter capacitors for low ripple DC output ¦ Power Battery Terminal (PBT) for easy
¦ LED indication for output input and output connection
¦ Four mounting holes of 3.2 mm each ¦ Filter capacitors for low ripple DC output
¦ PCB dimensions 35 mm x 45 mm ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 90 mm x 66 mm

5V/1A SYMMETRICAL 5V/3A SYMMETRICAL


REGULATED POWER SUPPLY G003 G004
REGULATED POWER SUPPLY
This kit provides Positive and Negative (Dual Output) 5 V @ 1 A Regulated
This kit provides Positive and Negative (Dual Output) 5V @ 3A regulated
Power Supply.
Power Supply.
¦ Input - 7-0-7 VAC to 15-0-15 VAC
¦ Input - 7-0-7 VAC to 15-0-15 V AC
¦ Output - Dual output ± 5 V @ 1 A
¦ Output - dual output ± 5 V @ 3 A
regulated low ripple DC voltage
regulated low ripple DC voltage
¦ Heatsink for regulator ICs
¦ Heatsink for regulator ICs
¦ Onboard bridge rectifier to convert AC to
¦ Onboard Bridge rectifier to convert AC to
DC
DC
¦ LED indication for both the outputs
¦ LED indication for both the outputs
¦ Thermal overload/short circuit protection
¦ Thermal overload/short circuit protection
(provided by IC feature)
(provided by IC feature)
¦ Power Battery Terminal (PBT) for easy
¦ Power Battery Terminal (PBT) for easy
input and output connection
input and output connection
¦ Filter capacitors for low ripple DC output
¦ Filter capacitors for low ripple DC output
¦ Four mounting holes of 3.2 mm each
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 46 mm x 60 mm
¦ PCB dimensions 107 mm x 107 mm

1.2 TO 25V/3A ADJUSTABLE 5A ADJUSTABLE


REGULATED POWER SUPPLY G005 G006
REGULATED POWER SUPPLY
This kit provides a variable output power supply ranging from 1.2 to 25 V This kit provides a variable output power supply ranging from 1.2 to 30 V
@ 3 A. Uses industry famous LM317K in TO3 package for delivering @ 5 A. Uses industry famous positive voltage regulator LM338K in TO3
variable output voltage. package for delivering variable output voltage.
¦ Input - minimum 30 VAC ¦ Input - minimum 35 VAC, 6 Amp
¦ Output - variable output from 1.2 ~ 25 V ¦ Output - variable output from 1.2 ~ 30 V
@ 3 A regulated low ripple DC voltage @ 5 A regulated low ripple DC voltage
¦ Heatsink for regulator IC ¦ Heatsink for regulator IC
¦ Onboard bridge rectifier to convert AC to ¦ Onboard bridge rectifier to convert AC to
DC DC
¦ LED indication at input of IC ¦ LED indication at input of IC
¦ Thermal overload/short circuit protection ¦ Thermal overload/short circuit protection
(provided by IC feature) (provided by IC feature)
¦ Power Battery Terminal (PBT) for easy ¦ Power Battery Terminal (PBT) for easy
input and output connection input and output connection
¦ Relimate connector for connecting ¦ Relimate connector for connecting
Potentiometer (POT) to the PCB Potentiometer (POT) to the PCB
¦ Filter capacitors for low ripple DC output ¦ Filter capacitors for low ripple DC output
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 91 mm x 66 mm ¦ PCB dimensions 91 mm x 66 mm

sales@anykits.co.in 20 www.anykits.co.in
POWER SUPPLY

1.2 - 15V/3A ADJUSTABLE


REGULATED POWER SUPPLY G007 MINI 7805 REGULATOR G008

This kit provides a variable output power supply ranging from 1.2 to 15 V This kit provides 5 VDC @ 1 A regulated supply. This mini kit is based on
@ 3 A. It uses Low Dropout Positive Regulator LM1084 in TO220 package the famous 7805 voltage regulator in TO220 package.
for delivering variable output voltage.
¦ Input - 7 to 18 VDC
¦ Input - 18 VAC/DC ¦ Output - 5 V @ 1 A regulated low ripple DC
¦ Output - variable output from 1.2 ~ 15 V voltage
@ 3 A Regulated low ripple DC voltage ¦ Thermal overload/short circuit protection
¦ Heatsink for regulator IC (provided by IC feature)
¦ On board bridge rectifier to convert AC to ¦ Berg connector for connecting input and
DC output
¦ LED indication at input of IC ¦ Filter capacitors for low ripple DC output
¦ Zener trimmed band gap reference, ¦ PCB dimensions 15 mm x 37 mm
current limiting and thermal shutdown
(provided by IC feature)
¦ Power Battery Terminal (PBT) for easy
input and output connection
¦ Onboard PCB mounted Potentiometer
(POT) for varying the output voltage
¦ Filter capacitors for low ripple DC output
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 46 mm x 58 mm

TESLA COIL IGNITOR G010

This kit is an ideal solution for power supply requirements of your TESLA
coil experiments. Onboard oscillator can generate 20 KHz up to 30 KHz
frequency required for energizing TESLA coil.
TINY 5V REGULATOR G009 ¦ Input 12 VDC @ 500 mA (current depends
on coil)
¦ Onboard PRESET to adjust frequency of
This kit provides 5 VDC @ 100 mA regulated supply. This tiny kit is based
on the famous 7805 voltage regulator in TO92 package. oscillator
¦ Diode protection at the output against
¦ Input - 7 to 18 VDC back EMF produced by the Coil
¦ Output - 5 V @ 100 mA regulated low ¦ Heatsink for switching transistor
ripple DC voltage ¦ LED indication for input
¦ Thermal overload/short circuit protection ¦ Power Battery Terminal (PBT) for easy
(provided by IC feature) input and output connection
¦ Berg connector for connecting input and ¦ Four mounting holes of 3.2 mm each
output ¦ PCB dimensions 51 mm x 54 mm
¦ Filter capacitors for low ripple DC output
¦ PCB dimensions 15 mm x 37 mm

3A DUAL ADJUSTABLE DUAL ADJUSTABLE


REGULATED POWER SUPPLY G011 G012
REGULATED POWER SUPPLY
This kit provides Positive and Negative (Dual) variable output power This kit provides Positive and Negative (Dual) variable output power
supply ranging from 1.2 to 30 V @ 3 A. Uses industry famous LM317K and supply ranging from 1.2 to 25 V @ 1 A. Uses industry famous LM317T and
LM337K in TO3 package for delivering variable output voltage. LM337T in TO220 package for delivering variable output voltage.
¦ Input - minimum 30 VAC ¦ Input - minimum 30 VAC
¦ Output - dual variable output from ± 1.2 ~ ¦ Output - dual variable output from ± 1.2 ~
30 V @ 3 A regulated low ripple DC voltage 25 V @ 1 A regulated low ripple DC voltage
¦ Heatsink for regulator IC ¦ Heatsink for regulator IC
¦ Onboard bridge rectifier to convert AC to ¦ Onboard bridge rectifier to convert AC to
DC DC
¦ LED indication at input of IC’s ¦ LED indication at input of IC's
¦ Thermal overload/short circuit protection ¦ Thermal overload/short circuit protection
(provided by IC feature) (provided by IC feature)
¦ Power Battery Terminal (PBT) for easy ¦ Power Battery Terminal (PBT) for easy
input and output connection input and output connection
¦ Relimate connector for connecting ¦ Relimate connector for connecting
Potentiometer (POT) to the PCB Potentiometer (POT) to the PCB
¦ Filter capacitors for low ripple DC output ¦ Filter capacitors for low ripple DC output
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 112 mm x 107 mm ¦ PCB dimensions 59 mm x 72 mm

sales@anykits.co.in 21 www.anykits.co.in
POWER SUPPLY

TINY 1.2 - 30V REGULATED


POWER SUPPLY G013 9 VDC POWER SUPPLY G015

This kit provides a variable output power supply ranging from 1.2 to 30 V Tiny low current 9 VDC Regulated Power Supply for testing the Op-Amp
@ 1.5 A. Uses industry famous LM317 in TO220 package for delivering based projects.
variable output voltage.
¦ Input - 10 to 18 VDC or AC, 200 mA
¦ Input - minimum 30 VAC ¦ Output - 9 VDC, Zener regulated low ripple
¦ Output - variable output from 1.2 ~ 30 V DC voltage
@ 3 A regulated low ripple DC voltage ¦ Input bridge rectifier made from discrete
¦ Heatsink for regulator IC Diodes
¦ Onboard bridge rectifier to convert AC to ¦ LED indication for output
DC ¦ Terminal pins for connecting input and
¦ LED indication at input of IC output
¦ Thermal overload/short circuit protection ¦ Four mounting holes of 3.2 mm each
(provided by IC feature) ¦ PCB dimensions 29 mm x 44 mm
¦ Power Battery Terminal (PBT) for easy
input and output connection
¦ Relimate connector for connecting
Potentiometer (POT) to the PCB
¦ Filter capacitors for low ripple DC output
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 39 mm x 53 mm

3A DUAL UNREGULATED
POWER SUPPLY G017

This kit will source Dual Unregulated Power Supply for your project. Ideal
for Audio amplifier, Mixer design etc.
¦ Input - maximum 48-0-48 VAC, 3 A
DUAL POLARITY 9V ¦ Output - maximum dual output ± 60 VDC
REGULATED POWER SUPPLY G016 from center tap transformer
¦ Bridge rectifier made of discrete 3 A diodes
¦ LED indication for both the outputs
This kit provides Zener Regulated Dual ± 9 VDC output power supply.
¦ Fuse short circuit protection for both the
¦ Input - 12-0-12 VAC, 500 mA outputs
¦ Output - ± 9 VDC / 250 mA, Zener ¦ Power Battery Terminal (PBT) for easy
regulated low ripple DC voltage input and output connection
¦ Input bridge rectifier made from discrete ¦ Filter capacitors for near ripple free DC
Diodes output
¦ Power Battery Terminal (PBT) for easy ¦ Four mounting holes of 3.2 mm each
input and output connection ¦ PCB dimensions 96 mm x 56 mm
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 39 mm x 60 mm

VARIABLE POWER SUPPLY G019


DUAL UNREGULATED
POWER SUPPLY G018
This kit provides a variable output power supply ranging from 2.6 to 24 V
@ 2.5 A. It's an ideal add-on to your workbench. Uses the industry
This kit will source Dual Unregulated Power Supply for your project. Ideal famous LM723 in DIP package.
for Audio amplifier, Mixer design etc.
¦ Input - minimum 30 VAC
¦ Input - maximum 30-0-30 VAC, 1 Amp ¦ Output - variable output from 2.6 ~ 24 V
¦ Output - maximum dual output ± 35 VDC @ 2.5 A regulated low ripple DC voltage
from center tap transformer ¦ Heatsink provided for output transistor
¦ Bridge rectifier made of discrete 1A diodes ¦ Bridge rectifier made up of discrete 3 A
to convert AC to DC diodes to Convert AC to DC
¦ LED indication for both the outputs, helps ¦ LED indication for input
in fault finding ¦ Power Battery Terminal (PBT) for easy
¦ Power Battery Terminal (PBT) for easy input and output connection
input and output connection ¦ Onboard PCB mounted POT for varying the
¦ Filter capacitors for near ripple free DC output voltage
output ¦ Filter capacitors for low ripple DC output
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 43 mm x 69 mm ¦ PCB dimensions 67 mm x 89 mm

sales@anykits.co.in 22 www.anykits.co.in
POWER SUPPLY

VARIABLE AUXILIARY
POWER SUPPLY G020 MINI DRILL POWER SUPPLY G021

This kit provides a variable output power supply ranging from 2.6 to 24 V This kit will control the speed of your hobby drill with changing output
@ 1 A. It's an ideal add-on to your workbench. Uses the industry famous voltage. Uses the industry famous LM317 in TO220 package for delivering
LM723 in DIP package. variable output (Voltage).
¦ Input - minimum 30 VAC ¦ Input - 15 VAC/DC, 1 A
¦ Output - variable output from 2.6 ~ 24 V ¦ Output - upto 12 VDC
@ 1 A regulated low ripple DC voltage ¦ Heatsink for regulator IC
¦ Heatsink provided for output transistor ¦ Bridge rectifier made using discrete 1 A
¦ Bridge rectifier made up of discrete 3 A diodes
diodes to convert AC to DC ¦ LED indication for input
¦ LED indication for input ¦ Thermal overload/short circuit protection
¦ Power Battery Terminal (PBT) for easy (provided by IC feature)
input and output connection ¦ Power Battery Terminal (PBT) for easy
¦ Onboard PCB mounted POT for varying the input and output connection
output voltage ¦ Onboard PCB mounted POT for varying the
¦ Filter capacitors for low ripple DC output output Voltage
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 61 mm x 76 mm ¦ PCB dimensions 39 mm x 74 mm

5V & 12V REGULATED


POWER SUPPLY G022 HALFWAVE RECTIFIER G023

This kit can be used to power up TTL and CMOS based projects, it provides Small Half Wave Rectifier kit, for power supply experiments.
5 VDC & 12 VDC @ 1Amp outputs. The kit is based on the industry famous
¦ Input - max 18 VAC, 1 Amp
7800 series voltage regulator in TO220 packages.
¦ Output - depends on transformer voltage
¦ Input - 18 VAC/DC which should not be more than 18 VAC
¦ Output - 5 V & 12 V @ 1 A regulated low ¦ Power Battery Terminal (PBT) for easy
ripple DC voltage input connection
¦ Onboard Diode Rectifier to convert AC to ¦ Four mounting holes of 3.2 mm each
DC ¦ PCB dimensions 25 mm x 32 mm
¦ Thermal overload/short circuit protection
(provided by IC feature)
¦ Power Battery Terminal (PBT) for easy
input and output connection
¦ Filter capacitors for low ripple DC output
¦ LED indication at input of IC
¦ PCB dimensions 37 mm x 61 mm

FULLWAVE BRIDGE RECTIFIER G025


FULLWAVE CENTER-TAP
RECTIFIER G024 Small Full Wave Bridge Rectifier kit, for power supply experiments.
¦ Input - maximum 18 VAC, 1 Amp
Small Full Wave Rectifier kit, for power supply experiments ¦ Output - depends on transformer voltage
¦ Input - 18 VAC center-tap, 1Amp which should not be more than 18 VAC
¦ Output - depends on transformer voltage ¦ Power Battery Terminal (PBT) for easy
which should not be more than 18 VAC input connection
¦ Power Battery Terminal (PBT) for easy ¦ LED indication for output
input connection ¦ Four mounting holes of 3.2 mm each
¦ LED indication for output ¦ PCB dimensions 31 mm x 41 mm
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 32 mm x 39 mm

90V/10A UNREGULATED
POWER SUPPLY G029
80V/10A UNREGULATED
POWER SUPPLY G028
This kit is designed to provide unregulated high voltage, high current for
your demanding needs. Ideally suited for use in Audio Amplifier design
This kit is designed to provide unregulated high voltage, high current for projects.
your demanding needs. Ideally suited for use in Audio Amplifier design
projects. ¦ Input - 0 - 75 VAC, 10 Amp
¦ Unregulated fused output with extra
¦ Input - 0 - 75 VAC, 10 Amp filtering
¦ Unregulated fused output ¦ 10 A bridge rectifier on board
¦ 10 A bridge rectifier on board ¦ LED indication for output
¦ LED indication for output ¦ PCB mounted LUGS for connecting input
¦ PCB mounted LUGS for connecting input and output
and output ¦ Four mounting holes of 3.2 mm each
¦ Four mounting holes of 3.2 mm each ¦ PCB dimensions 74 mm x 96 mm
¦ PCB dimensions 51 mm x 97 mm

sales@anykits.co.in 23 www.anykits.co.in
POWER SUPPLY

DUAL 80V/10A UNREGULATED DUAL 90V/10A UNREGULATED


POWER SUPPLY G030 POWER SUPPLY G031

This kit is designed to provide symmetrical output unregulated, high This kit is designed to provide symmetrical output unregulated, high
voltage, high current for your demanding needs. Ideally suited for use in voltage, high current for your demanding needs. Ideally suited for use in
Audio Amplifier design projects. Audio Amplifier design projects.
¦ Input - maximum 80 VAC Center-tap, 10 A ¦ Input - maximum 80 VAC center-tap,
¦ Symmetrical unregulated, individually 10Amp
fused outputs ¦ Symmetrical unregulated, individually
¦ 10A bridge rectifier on board fused outputs
¦ LED indication for both the outputs ¦ 10A bridge rectifier on board
¦ PCB mounted LUGS for connecting of input ¦ LED indication for both the outputs
and output ¦ PCB mounted LUGS for connecting of input
¦ Four mounting holes of 3.2 mm each and output
¦ PCB Dimensions 114 mm x 84 mm ¦ Four mounting holes of 3.2 mm each
¦ PCB Dimensions 154 mm x 84 mm

5V REGULATED 12V REGULATED


POWER SUPPLY MODULE G033 POWER SUPPLY MODULE G034

This kit is designed to provide 5 V @ 500 mA DC regulated supply with an This kit is designed to provide 12 V @ 700 mA DC regulated supply with an
onboard mains transformer. This kit is based on the famous 7805 voltage onboard mains transformer. This kit is based on the famous 7812 voltage
regulator in TO220 package. regulator in TO220 package.
¦ Input - 230 VAC Or 110 VAC, Jumper ¦ Input - 230 VAC Or 110 VAC, Jumper
setting for 110 VAC setting for 110 VAC
¦ Output - 5 V @ 500 mA regulated low ¦ Output - 12 V @ 700 mA regulated low
ripple DC voltage ripple DC voltage
¦ Thermal overload/short circuit protection ¦ External On/Off switch connection possible
(provided by IC feature) ¦ Thermal overload/short circuit protection
¦ Power Battery Terminal (PBT) for easy (provided by IC feature)
input and output connection ¦ Power Battery Terminal (PBT) for easy
¦ External On/Off switch connection possible input and output connection
¦ LED indication for output ¦ LED indication for output
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB Dimensions 72 mm x 40 mm ¦ PCB Dimensions 81 mm x 49 mm

5V & 12V REGULATED


POWER SUPPLY MODULE G035 8VAC POWER SUPPLY MODULE G036

This kit can be used to power up TTL and CMOS based projects, it provides This kit, used to provide 8 VAC @ 500 mA, is ideal for powering many
5 VDC & 12 VDC outputs with an onboard mains transformer. The kit is anykits projects.
based on the industry famous 7800 series voltage regulator in TO220
¦ Input - 230 VAC Or 110 VAC, Jumper
packages.
setting for 110 VAC
¦ Input - 230 VAC Or 110 VAC, Jumper ¦ Output - 8 VAC @ 500 mA
setting for 110 VAC ¦ Power Battery Terminal (PBT) for easy
¦ Output - 5 V @ 300 mA, 12 V @ 600 mA input and output connection
regulated low ripple DC voltage ¦ External On/Off switch connection possible
¦ Thermal overload/short circuit protection ¦ Four mounting holes of 3.2 mm each
(provided by IC feature) ¦ PCB dimensions 61 mm x 40 mm
¦ Power Battery Terminal (PBT) for easy
input and output connection
¦ External On/Off switch connection possible
¦ LED indication for outputs
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 87 mm x 49 mm

15VAC POWER SUPPLY


MODULE G037

This kit, used to provide 15 VAC @ 1A, is ideal for powering many anykits
projects.
¦ Input - 230 VAC Or 110 VAC, Jumper
setting for 110 VAC
¦ Output - 15 VAC @ 1A
¦ Power Battery Terminal (PBT) for easy
input and output connection
¦ External On/Off switch connection possible
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 69 mm x 49 mm

sales@anykits.co.in 24 www.anykits.co.in
REMOTE CONTROL

8 CHANNEL INFRARED 4 CHANNEL INFRARED


REMOTE H001 REMOTE H002

8 Channel Infrared (IR) Remote kit is a simple remote control kit which you 4 Channel Infrared (IR) Remote is a simple kit using the famous HT12A
can connect to various existing projects. You can also interface this kit to and HT12D encoder / decoder chips from Holtek. You can also interface
our Eight Channel Relay Board (I007). this kit to our Four Channel Relay Board (I006).
¦ Supply - Transmitter : 2.4 ~ 6 VDC, 5 V @ ¦ Supply - Transmitter : 2.4 ~ 5 VDC, 5 V @
150 mA & Receiver : 9 ~ 12 VDC, 12 V @ 20 mA & Receiver : 9 ~ 12 VDC, 12 V @ 40
25 mA mA
¦ Output - 2 Latched, 6 Momentary TTL ¦ Output - 4 Latched TTL compatible output
compatible outputs ¦ Crystal based oscillator for reliability of
¦ Crystal based oscillator for reliability of operation
operation ¦ DIP switch selectable 8 bit address code
¦ Crystal based design improves the ¦ LED output to indicate reception
oscillator's frequency stability ¦ ON/OFF slide switch in the transmitter
¦ Jumper selectable custom codes to operate ¦ Power-On LED indicator in the Receiver /
more than one unit in the same area Transmitter
¦ LED output to indicate transmission status ¦ High noise immunity
¦ High noise immunity ¦ Berg connector for interfacing of the board
¦ Terminal pins for easy connecting power ¦ Four mounting holes of 3.2 mm each
supply ¦ PCB dimensions - Transmitter : 61 mm x
¦ Berg connector for interfacing of receiver 47 mm & Receiver : 46 mm x 46 mm
board
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions - Transmitter : 37 mm x
82 mm & Receiver : 54 mm x 56 mm
8 CHANNEL RF REMOTE H005

8 Channel RF Remote kit is a simple remote control kit which you can
RF BASED DC MOTOR
DIRECTION CONTROLLER H003 connect to various existing projects. You can also interface this kit to our
Eight Channel Relay Board (I007).
¦ Supply - Transmitter : 2.4 ~ 6 VDC, 5 V @
RF Based DC Motor Direction Controller kit provides an easy way to control
150 mA & Receive : 9 ~ 12 VDC, 12 V @
the direction of your DC Motor connected to the receiver. This kit uses the
25 mA
famous HT12E and HT12D encoder / decoder chips from Holtek. With
¦ Output - 2 Latched, 6 Momentary TTL
jumper selectable address on the receiver and transmitter we can control
compatible output
upto 255 more motors in one area without interference with one remote.
¦ Crystal based oscillator for reliability of
ideal for mechatronics applications.
operation
¦ Supply - Transmitter : 2.4 ~ 5 VDC, 5 V @ ¦ Jumper selectable custom codes to operate
20 mA & Receiver : 5 VDC @ 31 mA more than one unit in the same area
without Motor ¦ LED output to indicate transmission status
¦ Motor - 1.5 to 5 VDC @ 500 mA ¦ High noise immunity
¦ Upto 30 meters range (Indoor) ¦ Terminal pins for easy connecting power
¦ DIP switch selectable 8 bit address code supply
¦ LED output to indicate reception ¦ Berg connector for interfacing of receiver
¦ ON/OFF slide switch in the transmitter board
¦ Power-On LED indicator in the Receiver / ¦ Four mounting holes of 3.2 mm each
Transmitter ¦ PCB dimensions - Transmitter : 35 mm x
¦ High noise immunity 74 mm & Receiver : 47 mm x 37 mm
¦ Power Battery Terminal (PBT) and Terminal
pins for easy input / output connection
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions - Transmitter : 60 mm x
37 mm & Receiver : 60 mm x 58 mm

sales@anykits.co.in 25 www.anykits.co.in
BUILDING BLOCKS

SINGLE CHANNEL RELAY DUAL CHANNEL RELAY


BOARD I004 BOARD I005

Single Channel Relay Board is a simple and convenient way to interface a Dual Channel Relay Board is a simple and convenient way to interface 2
relay for switching application in your project. relays for switching application in your project.
¦ Input - 12 VDC @ 42 mA ¦ Input - 12 VDC @ 84 mA
¦ Output - SPDT relay ¦ Output - two SPDT relay
¦ Relay specification - 5 A @ 230 VAC ¦ Relay specification - 5 A @ 230 VAC
¦ Trigger level - 2 ~ 5 VDC ¦ Trigger level - 2 ~ 5 VDC
¦ Berg pins for connecting power and trigger ¦ Berg pins for connecting power and trigger
voltage voltage
¦ LED indicates relay status ¦ LED on each channel indicates relay status
¦ Power Battery Terminal (PBT) for easy ¦ Power Battery Terminal (PBT) for easy
relay output connection relay output connection
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 27 mm x 69 mm ¦ PCB dimensions 49 mm x 68 mm

QUAD CHANNEL RELAY 8 CHANNEL RELAY


BOARD I006 BOARD I007

Quad Channel Relay Board is a simple and convenient way to interface 4 8 Channel Relay Board is a simple and convenient way to interface 8 relays
relays for switching application in your project. for switching application in your project.
¦ Input - 12 VDC @ 169 mA ¦ Input - 12 VDC @ 336 mA
¦ Output - four SPDT relay ¦ Output - eight SPDT relay
¦ Relay specification - 5 A @ 230 VAC ¦ Relay specification - 5 A @ 230 VAC
¦ Trigger level - 2 ~ 5 VDC ¦ Trigger level - 2 ~ 5 VDC
¦ Berg pins for connecting power and trigger ¦ Berg pins for connecting power and trigger
voltage voltage
¦ LED on each channel indicates relay status ¦ LED on each channel indicates relay status
¦ Power Battery Terminal (PBT) for easy ¦ Power Battery Terminal (PBT) for easy
relay output and aux power connection relay output and aux power connection
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 88 mm x 68 mm ¦ PCB dimensions 169 mm x 72 mm

OPTO-ISOLATED 4-CHANNEL OPTO-ISOLATED 8-CHANNEL


TRIAC BOARD I026 TRIAC BOARD I032

Opto-isolated 4-Channel Triac Board is used for fast switching Opto-isolated 8-Channel Triac Board is used for fast switching
applications. Ideal for switching mains circuits, lights, appliances and applications. Ideal for switching mains circuits, lights, appliances and
small loads. Each circuit is effectively isolated with opto-isolators on each small loads. Each circuit is effectively isolated with opto-isolators on each
channel, TTL inputs control each channel. channel, TTL inputs control each channel.
¦ Trigger input - 5 VDC, individual cathode ¦ Trigger input - 5 VDC, individual cathode
and anode out and anode out
¦ Input supply - 230 VAC ¦ Input supply - 230 VAC
¦ Output - 1 A @ 230 VAC ¦ Output - 1 A @ 230 VAC
¦ Berg pins for connection of control signal ¦ Berg pins for connection of control signal
¦ Snubber circuit for inductive load switching ¦ Power Battery Terminal (PBT) for easy
¦ Power Battery Terminal (PBT) for easy TRIAC output connection
TRIAC output connection ¦ Four mounting holes of 3.2 mm each
¦ Four mounting holes of 3.2 mm each ¦ PCB dimensions 80 mm x 174 mm
¦ PCB dimensions 77 mm x 149 mm

4-CHANNEL RELAY
OPTO-ISOLATED 4-CHANNEL BOARD - 1 I035
TRIAC BOARD (R) I034
4-Channel Relay Board-1 is a simple and convenient way to interface 4
Opto-Isolated 4-Channel Triac Board (R) is used for fast switching relays for switching application in your project.
applications. Ideal for switching mains circuits, lights, appliances and
¦ Input - 12 VDC @ 360 mA
small loads. Each circuit is effectively isolated with opto-isolators on each
¦ Output - Four SPDT Relay
channel, TTL inputs control each channel.
¦ Relay specification - 10 A @ 230 VAC
¦ Trigger input - 5 VDC, individual cathode ¦ Trigger level - 2 ~ 5 VDC
and anode out ¦ Box Header connector for connection of
¦ Input supply - 230 VAC trigger signal
¦ Output - 1 A @ 230 VAC ¦ LED on each channel indicates relay status
¦ Snubber circuit for inductive load switching ¦ Power-On LED indicator
¦ Jumper setting for cathode to common ¦ Power Battery Terminal (PBT) for easy
ground relay output and power in connection
¦ Box Header connector for connection of ¦ Four mounting holes of 3.2 mm each
control signal ¦ PCB dimensions 65 mm x 116 mm
¦ Power Battery Terminal (PBT) for easy
TRIAC output connection
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 139 mm x 73 mm

sales@anykits.co.in 26 www.anykits.co.in
BUILDING BLOCKS

4-CHANNEL RELAY
BOARD - 2 I036

4-Channel Relay Board-2 is a simple and convenient way to interface 4


relays for switching application in your project.
¦ Input - 12 VDC @ 170 mA
¦ Output - Four SPDT Relay
¦ Relay specification - 5 A @ 230 VAC
¦ Trigger level - 2 ~ 5 VDC
¦ Box Header connector for connection of
trigger signal
¦ LED on each channel indicates relay status
¦ Power-On LED indicator
¦ Power Battery Terminal (PBT) for easy
relay output and power in connection
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 56 mm x 83 mm

sales@anykits.co.in 27 www.anykits.co.in
MINI KITS

DARK SENSITIVE SWITCH J001 LIGHT SENSITIVE SWITCH J002

Dark Sensitive Switch is a simple project which operates a relay when the Light Sensitive Switch is a simple project which operates a relay when light
light falling on the LDR goes below a set point. falls on the LDR.
¦ Input - 12 V @ 55 mA ¦ Input - 12 V @ 55 mA
¦ Relay output - NC-C-NO ¦ Relay output - NC-C-NO
¦ Onboard preset to set the level ¦ Onboard preset to set the level
¦ Power-On LED indicator ¦ Power-On LED indicator
¦ Relay On LED indicator ¦ Relay On LED indicator
¦ Power Battery Terminal (PBT) for easy ¦ Power Battery Terminal (PBT) for easy
relay output connection relay output connection
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 44 mm x 49 mm ¦ PCB dimensions 44 mm x 49 mm

LED FLASHER J003 MINI MELODY GENERATOR J004

LED Flasher is a simple kit producing a flashing effect of six LED's. This kit Mini Melody Generator is a kit based on the
can be used in all areas where you want to draw attention. Hi-glow LED's famous BT66 melody IC. Working on 3 V
providing enough flashing light to attract your attention. (2AAA) battery it drives a 0.5 W, 8 Ohm
Speaker. PCB dimensions 27 mm x 54 mm
¦ Input - 12 V @ 35 mA
¦ Onboard preset to adjust flash rate
¦ Terminal pins for connecting power supply
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 53 mm x 35 mm

3 SIREN SOUND GENERATOR J005 TONE GENERATOR J006


3 Siren Sound Generator is based on UM3561 IC to generate sound.
Tone Generator is a simple kit which generates an Oscillating Frequency to
¦ Input - 6 VDC drive a PIEZO disc to produce tones.
¦ Onboard slide switch to select siren sound
¦ Input - 6 VDC @ 30 mA
¦ Terminal pins for connecting power supply
¦ Output Frequency Range - 800 Hz to
¦ Four mounting holes of 3.2 mm each
7.5 KHz
¦ PCB dimensions 42 mm x 42 mm
¦ Onboard preset to change Frequency /
Tone sound
¦ Terminal pins for connecting power supply
¦ Four mounting holes of 3.2 mm each
BATTERY OPERATED ¦ PCB dimensions 35 mm x 38 mm
DOOR BELL J007

Battery Operated Door Bell kit can be used at home as a Door Bell. This is
based on AP6201 IC.
MULTI MELODY GENERATOR J008
¦ Input - 5 VDC @ 20 mA
¦ 4 - different switches for 4 - different type
Multi Melody Generator kit is a capable of
of door bell melody
playing 25 different tones. Kit is designed
¦ Slide switch selectable - Continuous mode
for use in toys, doorbell, and music box.
and Non-retriggerable mode
Kit built around APM993 IC. Supply 5 VDC.
¦ Onboard LED indication to display melody
PCB dimensions 39 mm x 39 mm
being played
¦ Terminal pins for connecting power supply
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 51 mm x 42 mm
AUDIO DANCING LED J009

Audio Dancing LED kit is a fun filled project which generates a LED dancing
MULTI TONE MUSICAL BELL J010 sequence depending on the audio it senses. This kit is based on one of the
VU Meter IC's available.
Multi Tone Musical Bell is a simple and easy ¦ Power supply input - 6 ~ 9 VDC
Door Bell kit which changes melody with ¦ Output - 5 LED's
every press of a tactile switch. ¦ Onboard preset to adjust audio level to the
This kit operates on 3 VDC (2AAA Battery). IC
PCB dimensions 35 mm x 38 mm ¦ Onboard MIC capsule with Preamp
¦ Terminal pins for connecting power supply
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 39 mm x 67 mm

sales@anykits.co.in 28 www.anykits.co.in
MINI KITS

WATER LEVEL ALARM J012 MELODY GENERATOR J013

Water Level Alarm kit sounds an alarm when water reaches its sensor. Melody Generator kit plays a single melody as
This kit is a simple and a cost effective kit for use in home or industry. soon as power 3 VDC (2AAA Battery) is applied
to it. It is built around BT66T melody
¦ Power Supply Input - 6 VDC @ 25 mA
Generator IC.
¦ Output - Buzzer
PCB dimensions 30 mm x 23 mm.
¦ Onboard On/Off Switch
¦ Sensor PCB included
¦ Terminal pins for connecting power supply
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 63 mm x 42 mm 8 LED FLASHER J015

8 LED Flasher kit simply flashes a set of 8 LED's


to give you that reason to attract attention.
6 LED FLASHER J014 Power Supply - 9 V (PP3).
PCB dimensions 36 mm x 43 mm.

6 LED Flasher kit simply flashes a set of 6 LED's


to give you that reason to attract attention.
Power Supply - 9 V (PP3).
PCB dimensions 27 mm x 47 mm.

WHO’S FIRST (GAME)


INDICATOR J016

Who's First (Game) Indicator kit simply shows corresponding LED's for
whoever pushed the switch first.
¦ Upto four players can play simultaneously
¦ Well marked switches
¦ Each indication made of four LED's
¦ Reset switch overrides all inputs
¦ PCB dimensions 95 mm x 52 mm

sales@anykits.co.in 29 www.anykits.co.in
MISCELLANEOUS

PROTOTYPE BOARD K001 PROTOTYPE BOARD K002

High quality prototyping board for building and testing circuit solution. High quality prototyping board for building and testing circuits solution.
¦ Identifiable holes and tracks ¦ Identifiable holes and tracks
¦ Easy IC placement ¦ Easy IC placement
¦ Tracks both the ends for supply ¦ Tracks both the ends for supply
¦ Board Size 168 mm x 56 mm ¦ Board Size 89 mm x 56 mm

PROTOTYPE BOARD K003 GENERAL PURPOSE SMALL


EXPERIMENT BOARD K004
High quality prototyping board for building and testing microcontroller and
computer interface circuits. High quality small size general board for experiments, board with
¦ Identifiable holes and tracks individual copper per hole for quick fabrication and testing.
¦ Easy IC placement ¦ Board size 43 mm x 56 mm
¦ Tracks both the ends for supply ¦ 0.1” hole spacing
¦ One 25-Pin D Type Male/Female Connector ¦ Matrix 15 x 21
mounting
¦ One 9-Pin D Type Male/Female Connector
mounting
¦ Four 10-Pin Box header Connector
mounting
¦ Board Size 168 mm x 100 mm

GENERAL PURPOSE MEDIUM


EXPERIMENT BOARD K006
GENERAL PURPOSE SMALL
STRIPE BOARD K005
High quality medium size general board for experiments, board with
individual copper per hole for quick fabrication and testing.
High quality small general stripe board for experiments, for quick
fabrication and testing. ¦ Board size 86 mm x 56 mm
¦ 0.1” hole spacing
¦ Board size 43 mm x 56 mm ¦ Matrix 32 X 21
¦ 0.1” hole spacing
¦ Matrix 15 X 21

GENERAL PURPOSE LARGE


EXPERIMENT BOARD K008
GENERAL PURPOSE MEDIUM
STRIPE BOARD K007
High quality large size general board for experiments, board with
individual copper per hole for quick fabrication and testing.
High quality medium size general stripe board for experiments, for quick
fabrication and testing. ¦ Board size 86 mm x 111 mm
¦ 0.1” hole spacing
¦ Board size 86 mm x 56 mm
¦ Matrix 32 X 43
¦ 0.1” hole spacing
¦ Matrix 32 X 21

GENERAL PURPOSE EXTRA


GENERAL PURPOSE LARGE LARGE EXPERIMENT BOARD K010
STRIPE BOARD K009
High quality extra large size general board for experiments, board with
High quality large size general stripe board for experiments, for quick individual copper per hole for quick fabrication and testing.
fabrication and testing. ¦ Board size 86 mm x 169 mm
¦ Board size 86 mm x 111 mm ¦ 0.1” hole spacing
¦ 0.1” hole spacing ¦ Matrix 32 X 65
¦ Matrix 32 X 43

sales@anykits.co.in 30 www.anykits.co.in
MISCELLANEOUS

GENERAL PURPOSE EXTRA


LARGE STRIPE BOARD K011 LCD DIGITAL PANEL METER K012

High quality extra large size general stripe board for experiments, for LCD Digital Panel Meter for measuring can be used as Voltmeter, Ammeter
quick fabrication and testing. etc.
¦ Board size 86 mm x 169 mm ¦ Power supply input - 5 VDC @ 25 mA
¦ 0.1” hole spacing ¦ Terminal pins for connecting power supply
¦ Matrix 32 X 65 ¦ Berg pins for voltage input

FSK RF MODULES K014

FSK RF Modules Transmitter & Receiver.


LED DIGITAL PANEL METER K013
¦ Power supply input - 5 VDC
¦ Frequency 914.5 MHz
LED Digital Panel Meter for measuring can be used as Voltmeter, Ammeter ¦ ISM band
etc. ¦ Range outdoor upto 60 meter,
indoor upto 20 meter
¦ Power supply input - 5 VDC @ 150 mA
¦ Terminal pins for connecting power supply
¦ Berg pins for voltage input

ASK RF MODULES K015

ASK RF Modules Transmitter & Receiver.


¦ Power supply input - 5 VDC
¦ Frequency 434 MHz
¦ ISM band
¦ Range outdoor upto 60 meter,
indoor upto 20 meter

sales@anykits.co.in 31 www.anykits.co.in
MOTOR/MOTION CONTROL

BIPOLAR STEPPER MOTOR


DRIVER M001 DC SERVO MOTOR DRIVER M002

This kit is designed to drive two-phase stepper motor in bipolar mode. It is DC Servo Motor Driver kit, designed using MC33030 IC, is the fastest and
based on MC3479 IC. low cost way of getting your DC Servo Motor up and running.
¦ Input - 12 VDC (7.5 to 16 V supply ¦ Input - 12 VDC
possible) ¦ Output - can drive upto 1 A Load
¦ Two-phase stepper motor in bipolar mode ¦ Overcurrent shutdown, overvoltage
with up to 350 mA to each of the two coils shutdown
¦ Jumper selectable half or full step ¦ Programmable reference input
¦ Adjustable speed with the help of onboard ¦ Power-On LED indicator
preset ¦ Relimate connector for interfacing the kit
¦ Direction control with help of a on board ¦ Four mounting holes of 3.2 mm each
Slide switch ¦ PCB dimensions 45 mm x 54 mm
¦ Power-On LED indicator
¦ Power Battery Terminal (PBT) for easy
input (PWR) / output (Motor) connection
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 51 mm x 62 mm 0 TO 5V SERVO DRIVER M004

0 to 5V Servo Driver kit will control a DC Servo Motor using a varying


voltage input of 0 to 5 VDC.
555 STEPPER PULSE
GENERATOR M003 ¦ Input supply - 6 VDC
¦ 90° movement
¦ 0 to 5 VDC as controlling input for servo
The 555 Stepper Pulse Generator kit will help you with the pulse required
¦ Power-On LED indicator
to drive your favorite DC Servo Motor application. This kit uses the famous
¦ Berg connector for easy interfacing of the
555 timer IC for generating the Stepping Pulse.
kit
¦ Input - 5 - 12 VDC @ 25 mA ¦ Four mounting holes of 3.2 mm each
¦ TTL/CMOS interfaceable ¦ PCB dimensions 33 mm x 49 mm
¦ Jumper selectable two speed operation
¦ Onboard preset to vary the duty cycle
¦ Power-On LED indicator
¦ Terminal pins for easy interfacing of the kit SINGLE MOTOR L298
¦ Four mounting holes of 3.2 mm each H-BRIDGE CONTROL M006
¦ PCB dimensions 39 mm x 37 mm
Single Motor L298 H-Bridge Control kit will provide DC Motor control for
your application. This kit uses the famous industry standard L298 H-
Bridge IC.
¦ Motor supply - 7 to 46 VDC
555 DC MOTOR SPEED ¦ Control Logic Supply - Standard TTL logic
CONTROLLER M005 level
¦ Output DC drive to Motor - upto 2 A
¦ Current Sense Output available
555 DC Motor Speed Controller kit will control the speed of a DC motor
¦ Onboard resistor provided for current limit
connected to it. This kit is built using the famous 555 timer IC.
¦ Enable and direction control pins available
¦ Input supply - 12 VDC ¦ External diode bridge provided for output
¦ Output drive upto 800 mA ¦ Heatsink for IC
¦ Onboard preset to vary Duty Cycle from ¦ Power-On LED indicator
10% to 95% @ 120 Hz ¦ Power Battery Terminal (PBT) for easy
¦ Ideal for mini drill and robotics application input (PWR) / output (Motor) connection
¦ MOSFET based output drive with heatsink ¦ Four mounting holes of 3.2 mm each
¦ Diode protection for motor surge ¦ PCB dimensions 46 mm x 63 mm
¦ Power-On LED indicator
¦ Power Battery Terminal (PBT) for easy
input (PWR) / output (Motor) connection
¦ Four mounting holes of 3.2 mm each DUAL MOTOR L298
¦ PCB dimensions 47 mm x 56 mm
H-BRIDGE CONTROL M007

Dual Motor L298 H-Bridge Control kit can control two DC motors
connected to it. This kit uses the famous industry standard L298 H-Bridge
UNIPOLAR STEPPER
MOTOR DRIVER M009 IC.
¦ Motor supply - 7 to 46 VDC
Unipolar Stepper Motor Driver kit provides speed, direction and step size ¦ Control Logic Supply - Standard TTL logic
control, of a stepper motor connected to it. This kit is based on the famous level
UCN5804 Stepper Motor driver IC. ¦ Output DC drive to motor - upto 2 A each
¦ Current Sense Output available
¦ Input supply - 7 - 18 VDC ¦ Onboard resistor provided for current limit
¦ Output - upto 1 A per phase ¦ Enable and direction control pins available
¦ Standalone Controller Board ¦ External diode bridge provided for output
¦ Onboard preset for speed adjust ¦ Heatsink for IC
¦ Onboard slide switch for direction, step ¦ Power-On LED indicator
and phase control ¦ Power Battery Terminal (PBT) for easy
¦ Power-On LED indicator input (PWR) / output (Motor) connection
¦ Power Battery Terminal (PBT) for easy ¦ Four mounting holes of 3.2 mm each
input (PWR) / output (Motor) connection ¦ PCB dimensions 61 mm x 63 mm
¦ PCB dimensions 52 mm x 79 mm

sales@anykits.co.in 32 www.anykits.co.in
MOTOR/MOTION CONTROL

MOTOR SPEED & DIRECTION LIGHT SENSITIVE INDUCTIVE


CONTROLLER M008 LOAD CONTROLLER M010

Motor Speed & Direction Controller kit offers versatile control of speed and Light Sensitive Inductive Load Controller kit offers On / Off control,
direction for DC motor connected to it. This kit uses the famous depending on presence or absence of light. Some of the controllable
LMD18200 for Motor Drive and SG3525 to obtain PWM signal for precise inductive load could be single phase AC Motor, Solenoid Valve etc.
control.
¦ Input supply - 12 VDC
¦ Motor supply - 12 to 55 VDC @ 3 A Max ¦ Output - upto 200 W, 230 VAC
¦ Kit supply - 12 VDC @ 30 mA ¦ Opto-isolated Triac based design
¦ PWM Output - duty cycle of 0% to 100% @ ¦ Power-On LED indicator
3 KHz ¦ Power Battery Terminal (PBT) and Terminal
¦ Standalone Controller Board pins for easy input / output connection
¦ Onboard POT for speed adjust ¦ PCB dimensions 41 mm x 82 mm
¦ Onboard preset for frequency adjust
¦ Onboard slide switch for direction control
¦ Heatsink for motor drive IC
¦ Power-On LED indicator ON/OFF DC MOTOR
¦ Separate supply connector for motor and CONTROLLER M012
control section
¦ Power Battery Terminal (PBT) for easy
ON/OFF DC Motor Controller kit offers simple On/Off Switch Control.
input (PWR) / output (Motor) connection
¦ Four mounting holes of 3.2 mm each ¦ Input supply - 12 VDC @ 1 A
¦ PCB dimensions 53 mm x 63 mm ¦ Output - upto 1 A
¦ Onboard tactile switch for ON/OFF control
¦ MOSFET based drive design with diode
protection
ON/OFF AC MOTOR ¦ LED indicator for ON/OFF state
CONTROLLER M011 ¦ Power-On LED indicator
¦ Terminal pins and Power Battery Terminal
(PBT) for easy input / output connection
ON/OFF AC Motor Controller kit offers simple On/Off Switch Control.
¦ PCB dimensions 40 mm x 62 mm
¦ Input supply - 12 VDC @ 40 mA
¦ Output - upto 300 W - 230 VAC
¦ Onboard tactile switch for ON/OFF control
¦ Opto-isolated Triac based design
¦ Power-On LED indicator AC SOLID STATE RELAY M015
¦ Power Battery Terminal (PBT) and Terminal
pins for easy input / output connection AC Solid state Relay kit offers simple On/Off type Switch Control with TTL
¦ Four mounting holes of 3.2 mm each
compatible input signal.
¦ PCB dimensions 44 mm x 86 mm
¦ Input signal - 2 ~ 5 VDC, TTL compatible
¦ Output - upto 500 W, 230 VAC
¦ Optically isolated Triac based design
DC MOTOR DIRECTION ¦ Power Battery Terminal (PBT) and Terminal
CONTROL M013 pins for easy input / output connection
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 35 mm x 72 mm
DC Motor Direction Control kit offers direction control using digital logic
gates and a DPDT relay.
¦ Input supply - 12 VDC @ 75 mA
¦ Output - upto 5 A @ 30 VDC
¦ Onboard tactile switch for direction control L293 H-BRIDGE DC MOTOR
¦ Relay based drive design with diode CONTROLLER M017
protection
¦ LED indicator for direction indication L293 H-Bridge DC Motor Controller kit is a simple board to control motors
¦ Power-On LED indicator upto 1 A load.
¦ Terminal pins and Power Battery Terminal
(PBT) for easy input / output connection ¦ Motor supply - upto 36 VDC
¦ Four mounting holes of 3.2 mm each ¦ Control logic supply - Standard TTL /CMOS
¦ PCB dimensions 41 mm x 81 mm logic level
¦ Output DC drive to motor - upto 1 A
¦ Direction control pins available
¦ Jumper selectable enable pin
¦
AC MOTOR SPEED External diode bridge provided for output

CONTROLLER M016 ¦ Power-On LED indicator for both supplies


¦ Relimate Connector for easy connection of
input (PWR) / output (Motor)
AC Motor Speed Controller kit is a simple POT based speed controller ¦ PCB dimensions 40 mm x 50 mm
design for inductive type load.
¦ Input - 230 VAC
¦ Output - upto 500 W - 230 VAC
¦ Triac based design
¦ Power Battery Terminal (PBT) easy
connection
¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 50 mm x 47 mm

sales@anykits.co.in 33 www.anykits.co.in
MOTOR/MOTION CONTROL

JOYSTICK MOTOR
0 - 5V SERVO CONTROLLER M018 CONTROLLER M020

0 - 5V Servo Controller kit will control a hobby type servo motor connected Joystick Motor Controller kit control a hobby type servo motor connected
to it via a preset or external DC source. This kit will be ideal add on in to it via a joystick type (resistive) sensor connector. This kit will be ideal
animatronics and motion control application. add-on to animatronics and motion control application.
¦ Microcontroller based design for greater ¦ Microcontroller based design for greater
flexibility and ease of control flexibility and ease of control
¦ Single Servo control via clearly marked ¦ Single Servo control via clearly marked
Relimate Connector Relimate Connector
¦ Clearly marked jumper to select signal ¦ Onboard voltage regulator to provide
source to control the Servo regulated voltage to the kit
¦ Onboard preset for ready to control option ¦ Diode protection for reverse polarity
for this kit connection of DC supply to the PCB
¦ Power-on LED indicator ¦ Clearly marked relimate type connectors to
¦ Diode protection for reverse polarity interface Joystick and Servo Motor
connection of DC supply to the PCB ¦ Span adjust preset
¦ Four mounting holes of 3.2 mm each ¦ Four mounting holes of 3.2 mm each
¦ PCB dimensions 32 mm x 47 mm ¦ PCB dimensions 47 mm x 41 mm

HIGH CURRENT UNIPOLAR HIGH CURRENT BIPOLAR


STEPPER MOTOR CONTROLLER M022 STEPPER MOTOR CONTROLLER M023
High Current Unipolar Stepper Motor Controller kit is based on chopper High Current Bipolar Stepper Motor Controller kit is based on chopper
drive. Chopper drive allows for use of higher voltage power supply for drive. Chopper drive is a method of providing a constant current source to
better performance and higher speed. It uses SGS Thomson's L297 IC a device. Chopper drive allows for use of higher voltage power supply for
and TIP142 transistor. better performance and higher speed. It is uses SGS Thomson's L297 and
L298 controller IC's.
¦ Logic supply - 5 VDC @ 300 mA
¦ Motor Supply - 8 to 30 VDC ¦ Logic supply - 5 VDC @ 300 mA
¦ Connection via 10-pin Box Header for easy ¦ Motor Supply - 8 to 30 VDC
interface with any microcontroller ¦ Connection via 10-pin Box Header for easy
development boards interface with any microcontroller
¦ External or internal voltage reference development boards
option via jumper ¦ External or internal voltage reference
¦ Onboard preset for current adjustment option via jumper
¦ High speed switching diodes for transistor ¦ Onboard preset for current adjustment
protection ¦ High speed switching diodes for L298 IC
¦ Power-On LED indicator for both the protection
supplies ¦ Power-On LED indicator for both the
¦ Power Battery Terminal (PBT) for easy supplies
supplies and motor connection ¦ Power Battery Terminal (PBT) for easy
¦ Heat sink included supplies and motor connection
¦ Four mounting holes 3.2 mm each ¦ Heat sink included
¦ PCB dimensions 110 mm x 53 mm ¦ Four mounting holes 3.2 mm each
¦ PCB dimensions 74 mm x 71 mm

sales@anykits.co.in 34 www.anykits.co.in
Electronic Kits & Modules
TM

2, KRISHNA KUNJ
MAIN AVENUE,
SANTACRUZ (WEST)
MUMBAI 400 054. INDIA Www.anykits.co.in
PHONE +91 22 32928210 sales@anykits.co.in

Your kit distributor


ak-dc.07.08

Modification in pictures and text are reserved


All misprints reserved

You might also like