You are on page 1of 4

HP DESIGNJET L25000 SYSTEM ERROR CODE

01.0:03 - Error impact I2C channel 01.0:10 - Problem with the Sausalito PCA 01.1.10 - Problem with the Printmech PCA 01.02:10 - ISS PCA Problem 02.01:10 - Problem with the Carriage PCA 03:10 - Problem with the PSU 05.1:10 - Problem with the CPU Fan 05.3:10 - Main memory size failure 06.03 - NVM file has a bad CRC 06:10 - Main NVM failure 08:11 - Connection problem with the Front Panel 09.01:10 - TOMAS Error 11:10 - Connection problem with the Trailing cable 14.01:00 - Temperature high on the Heat sink 14.02:00 - Current too high on the Dryer Assembly 14.03:00 - Current too high on the Curing Module 14.04:00 - AC Voltage too high on the Dryer Assembly 14.05:00 - AC Voltage too low on the Dryer Assembly 14.06:00 - One or more heaters are not connected 14.07:00 - Connection problem with Heaters Control assembly 14.08:00 - No AC voltage in the Dryer Assembly 14.09:00 - Heaters Control PCA is not ready 14.10:00 - Open circuit on the Dryer Assembly 14.11:00 - Open circuit in the Curing Module 14.12:00 - Petisa Fan Fault 14.13:00 - Current Leak in Drying Channel 14.14:00 - Current leak in the Curing Module 14.15:00 - Generic failure with the Heaters Control Assembly 14.16:00 - AC voltage too high on the Curing Module 14.17:00 - AC Voltage too low on the Curing Module 15.01:00 Drying system warm up timed out 15.02:00 - Drying system cool down time out 15.03:00 - Drying system temperature too high 15.04:00 - Drying system temperature too low 15.05:00 - Problem with the Drying System Temperature Sensor 15.06:00 - Temperature error detected 15.08:00 - Dryer fans not connected 15.09:00 - Drying fans failure 15.10:00 - Drying Assembly resistors incorrect

16.01:00 - Curing Module warm up time out 16.02:00 - Curing system cool down time out 16.03:00 - Curing system temperature too high 16.04:00 - Curing system temperature too low (below 5C 16.05:00 - Problem with the Curing System Temperature Sensor 16.06:00 - Temperature error detected 16.08:00 - Curing System fans not connected 16.09:00 - Curing System fans failure 16.10:00 - Curing Assembly resistors incorrect 21.02:10 - Problem with the Web Wipe motor 21.03:10 - Electrical problem in the Web Wipe Motor 21.05:03 - Web Wipe Assembly Drifting 21:10 - Problem in the area of the Service Station 21:13 - Problem in the Service Station 23:10 - Problem with pressurization in the APS 23:10 - Problem with pressurization in the APS 24:03 - Ink Seup Failure 24:10 - Ink Cartridge Broken Bag 24.02:00 - Top Cover Fans array is not connectedystem Error Codes 24.03:00 - One of the Top Cover Fans not connected 26.00:10 - Contact failure with Magenta Ink Cartridge 26.01:10 - Contact failure with Yellow Ink Cartridge 26.02:10 - Contact failure with Black Ink Cartridge 26.03:10 - Contact failure with Cyan Ink Cartridge 26.04:10 - Contact failure with Light Magenta Ink Cartridge 26.05:10 - Contact failure with Light Cyan Ink Cartridge 26:14 - An incorrect Ink Cartridge has been detected 27:14 - An incorrect Printhead has been detected 29:02 - Printhead Cleaning Cartridge almost finished 32:01.01 - The substrate printed on is too small 32:01.02 - Problem with the Take Up Reel 32:01 - Take Up Reel disconnected 32:02 - Take Up Reel disconnected at initialization 41:03 - Limited electrical voltage at the Media Axis motor 41:10 - Electrical fault at the Media Axis motor 42:03 - Problem with the Scan Axis Motor 42:10 - Electrical fault in the Scan Axis area 43:10 - Problem with the Vacuum Fan 44:10 - There is a problem with the Aerosol Fan 44:11 - Connection problem with the Aerosol Fan 45.01:00 - Rewinder Servo Shutdown

45.02:10 - Rewinder inverse polarity 45.03:00 - Rewinder driver system fault 46:03 - Primer Servo shutdown 46:10 - Electrical fault in the Primer motor 46:13 - Primer distance failed 50:01 - OMAS Navigation failure 50:03 - Internal electrical connection problem 50.01:10 - Connection problem with OMAS 50.01:11 - Error with Media Advance Sensor or with cable 50:11 - Media navigation problem 50:14 - Firmware version mis-match 50.02:10 - Problem with OMAS Controller PCA 51:10 - An error has been detected with the Window Lock Sensor 51.01:10 - Problem with the Service Station door sensor 52:01 - A problem with the Drop Detector 52:10 - A problem with the On/Off switch in the Drop Detector 53:10 - Problem with the Media sensor 54:10 - Problem with the Media lever sensor 55:10 - Problem with the Line Sensor 56:10 - Analog encoder calibration has failed 58:10 - Problem with the Color Sensor 61:01 - Problem with the format of the file 61:08.01 - Job is password protected 61:09 - Communication with the RIP broken 63:04 - Network problem 63:05 - The raster data does not arrive quick enough 65:04 - I/O port problem 66:08 - Cannot print on the current type of media 71:19 - Mis-match of printer information 72:04 - Generic firmware error 73:03 - Problem with the Carriage encoder 74:01 - Error upgrading firmware file 74:04 - Request to upgrade the firmware 77:04 - Embedded Web Server internal software error 78.01:04 - Media settings error 78.02:01 - End of roll detected on the Rewinder 79:03 - Generic firmware error I 79:04 - Generic firmware error II 81:01 - Problem with the Media Drive 81:03 - Problem with setting the encoder position 82:01 - Media jam in the platen

85:03 - Drive Roller encoder problem 86:01 - Carriage servo shutdown 93:11 - Unable to pressurize the IDS

You might also like