Professional Documents
Culture Documents
MODEL:
PH-919 DVD PLAYER
CONTENTS
1. PRECAUTIONS-------------------------------------------------------------------------------------------------------------------- 1 1-1 SAFETY PRECAUTIONS ---------------------------------------------------------------------------------------------------------- 1 1-2 SERVICING PRECAUTIONS ------------------------------------------------------------------------------------------------------ 2 1-2-1 General Serving Precautions -------------------------------------------------------------------------------------------- 2 1-2-2 Insulation Checking Procedure------------------------------------------------------------------------------------------ 3 1-3 ESD PRECAUTIONS ------------------------------------------------------------------------------------------------------------- 3 2. REFERENCE INFORMATION ------------------------------------------------------------------------------------------------ 4 2-1 COMPONENT DESCRIPTIONS --------------------------------------------------------------------------------------------------- 4 2-1-1 DVD SANYO HD60 PUH ------------------------------------------------------------------------------------------------ 4 2-1-2 DVD Processor Chip (MTK1379) and Front-end IC MT1336------------------------------------------------------ 6 2-1-3 28-Pin, 24-Bit, 192kHz D/A with Volume Control (DA1196) ----------------------------------------------------15 2-1-4 Serial EEPROM, 16K (2048 x 8) (24C16)----------------------------------------------------------------------------17 2-1-5 8M-BIT [1Mx8/512Kx16] CMOS FLASH MEMORY ---------------------------------------------------------------18 2-1-6 512K X 16 Bit X 2 Banks Synchronous DRAM (A43L0616) -------------------------------------------------------20 3. PRODUCT SPECIFICATIONS------------------------------------------------------------------------------------------------23 4.UPGRADING SYSTEM AND CHANGING THE REGION CODE----------------------------------------------------24 5. OPERATING INSTRUCTION-------------------------------------------------------------------------------------------------25 MAINTENANCE & TROUBLESHOOTING ------------------------------------------------------------------------------------------26 6.DISASSEMBLY AND REASSEMBLY----------------------------------------------------------------------------------------28 7.TROUBLESHOOTING ----------------------------------------------------------------------------------------------------------30 8. ELECTRICAL PART LIST-----------------------------------------------------------------------------------------------------31 9. BLOCK DIAGRAM --------------------------------------------------------------------------------------------------------------38 10. CIRCUIT DIAGRAMS---------------------------------------------------------------------------------------------------------40 11. WIRING DIAGRAM------------------------------------------------------------------------------------------------------------48
1. PRECAUTIONS
1-1 Safety Precautions
1) Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: (1) Be sure that no built-in protective devices are defective or have been defeated during servicing. (1) Protective shields are provided to protect both the technician and the customer. Correctly replace all missing protective shields, including any remove for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including, but not limited to, nonmetallic control knobs, insulating fish papers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. (2) Be sure that there are no cabinet opening through which adults or children might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, excessively wide cabinet ventilation slots, and an improperly fitted and/or incorrectly secured cabinet back cover. (3) Leakage Current Hot Check-With the instrument completely reassembled, plug the AC line cord directly into a 120V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards institute (ANSI) C101.1 Leakage. Current for Appliances and underwriters Laboratories (UL) 1270 (40.7). With the instruments AC switch first in the ON position and then in the OFF position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinets, screwheads, metallic overlays, control shafts, etc.), especially and exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the outlet and repeat the test.
AC Leakage Test Any measurements not within the limits specified herein indicate a potential shock hazard that must be eliminated before returning the instrument to the customer. (4) Insulation Resistance Test Cold Check-(1) Unplug the power supply cord and connect a jumper wore between the two prongs of the plug. (2) Turn on the power switch of the instrument. (3) Measure the resistance with an ohmmeter between the jumpered AC plug and all exposed metallic cabinet parts on the instrument, such as screwheads, antenna, control shafts, handle brackets, etc. When an exposed metallic part has a return path to the chassis, the reading should be between 1 and 5.2 megohm. When there is no return path to the chassis, the reading must be infinite. If the reading is not within the limits specified, there is the possibility of a shock hazard, and the instrument must be re-pared and rechecked before it is returned to the customer.
voltage, and (5) antenna wiring. Always inspect in all areas for pinched, out-of-place, or frayed wiring. Do not change spacing between a component and the printed-circuit board, Check the AC power cord for damage. 5) Components, parts, and/or wiring that appear to have overheated or that are otherwise damaged should be replaced with components, parts and/or wiring that meet original specifications. Additionally determine the cause of overheating and/or damage and, if necessary, take corrective action to remove and potential safety hazard. 6) Product Safety Notice-Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by shading, an ( ) or a ( ) on schematics and parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might created shock, fire and/or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.
Insulation Resistance Test 2) Read and comply with all caution and safety related notes non or inside the cabinet, or on the chassis. 3) Design Alteration Warning-Do not alter of add to the mechanical or electrical design of this instrument. Design alterations and additions, including but not limited to, circuit modifications and the addition of items such as auxiliary audio output connections, might alter the safety characteristics of this instrument and create a hazard to the user. Any design alterations or additions will make you, the service, responsible for personal injury or property damage resulting there from. 4) Observe original lead dress. Take extra care to assure correct lead dress in the following areas: (1) near sharp edges, (2) near thermally hot parts (be sure that leads and components do not touch thermally hot parts), (3) the AC supply, (4) high
1-2-1 General Serving Precautions (1) a. Always unplug the instruments AC power cord from the AC power source before (1) removing or reinstalling any component, circuit board, module or any other instrument assembly. (2) disconnecting any instrument electrical plug or other electrical connection. (3) connecting a test substitute in parallel with an electrolytic capacitor in the
2
(3) The components used in the unit have a specified flame resistance and dielectric strength. When replacing components, use components which have the same ratings, by ( ) or by ( ) in the circuit diagram are important for safety or for the characteristics of the unit. Always replace them with the exact replacement components. (4) An insulation tube or tape is sometimes used and some components are raised above the printed wiring board for safety. The internal wiring is sometimes clamped to prevent contact with heating components. Install such elements as they were. (5) After servicing, always check that the removed screws, components, and wiring have been installed correctly and that the portion around the serviced part has not
been damaged and so on. Further, check the insulation between the blades of the attachment plus and accessible conductive parts.
1-2-2 Insulation Checking Procedure Disconnect the attachment plug from the AC outlet and turn the power ON. Connect the insulation resistance meter (500V) to the blades of the attachment plug. The insulation resistance between each blade of the attachment plug and accessible conductive parts (see note) should be more than 1 Megohm.
Note: Accessible conductive parts include metal panels, input terminals, earphone jacks, etc.
2. Reference Information
2-1 Component Descriptions
2-1-1 DVD SANYO HD60 PUH
Connector Pin Definition
I/F Signals
FF+ T+ TC D CD/DVD RF A B F GND-PD VC VCC E NC VR-CD VR-DVD LD-CD MD HFM NC LD-DVD GND-LD
I/O Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
4. Block Diagram
Disc
MT1369 (RF AMP) MT1369 (Decode/Servo) ATAPI Buffer Manager Demodulator Error Correction PLI Focus & Tracking
Video D/A
Laser pickup
SDRAM 1*16MHzX2
Loading
CS4955
Spindle Motor
Focus Coil
Track Coil
Sied Motor
Memory 8Mbit
2-1-2 DVD Processor Chip (MTK1379) and Front-end IC MT1336 * Features Single-chip DVD video decoder in a 208-pin PQFP package Supports MPEG-1 system and MPEG-2 program streams Programmable multimedia processor architecture Compatible with Audio CD, Video CD, VCD 3.0, and Super Video CD (SVCD) DVD Navigation 1 Built-in content Scrambling System (CSS) - Audio Built-in Karaoke key-shift function DolbyTM Digital 2-channel down mix audio output for DolbyTM Dolby Pro Logic Linear PCM streams for24 bit / 96KHz Concurrent S/PDIF out and 2-channel audio output Sensaura Dolby Digital Virtual Surround DTS Digital Surround 2-channel down mix stereo output S/PDIF output for encoded AC-3, DTS Digital output or Linear PCM - Peripheral Glueless interface to DVD loaders (ATAPI or A/V bus I/F) Bi-directional 12C audio interface 8 general-purpose auxiliary ports Single 27MHz clock input - Smart Technology SmartZoomTM for motion zoom & pan SmartZoomTM for NTSC to PAL conversion and vice versa SmartZoomTM for video error concealment * Functional Description
* Pinout Diagram
8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
IREF PLLVSS LPIOP LPION LPFON LPFIP LPFIN LPFOP JITFO JITFN PLLVDD3 FOO TRO TROPENPWM PWMOUT1 PWMOUT2 DVDD2 DMO FMO DVSS FG HIGHA0 HIGHA1 HIGHA2 HIGHA3 HIGHA4 HIGHA5 DVSS HIGHA6 HIGHA7 AD7 AD6 AD5 AD4 DVDD3 AD3 AD2 AD1 AD0 IOA0 IOA1 DVDD2 IOA2 IOA3 IOA4 IOA5 IOA6 IOA7 A16 A17 IOA18 IOA19 IOA20 APLLVSS
MT1379_216
RFIP RFIN RFDTSLVN RFDTSLVP ADCVDD3 PWM2VREF PWMVREF HRFZC RFRP_AC RFRP_DC RFLEVEL FEI CSO TEI TEZISLV RFSUBI ADIN ADCVSS BDO SLCK SDEN SDATA WOBSI UDGATE DVDD3 IDGATE VFO13 DVSS PRST XTALI XTALO DVDD3 SPBCK SPLRCK DVDD2 SPDATA SPMCLK HSYN DVSS YUV7 VSYN BLANK# ICE YUV6/R YUV5/B DACVSSA YUV4/G DACVDDA YUV3/CVBS DACVSSB YUV2/Y DACVDDB YUV1/C DACVSSC
216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163
YUV0/CIN FS VREF DACVDDC ASDATA4 ASDATA3 ASDATA2 ASDATA1 ASDATA0 SPDIF MC_DATA ACLK DVDD3 ALRCK ABCK RD16 RD17 DVSS RD18 RD19 RD20 RD21 DVDD2 RD22 RD23 DQM2 DQM3 DVSS RD24 RD25 RD26 RD27 DVDD3 RD28 RD29 RD30 RD31 DVSS RA3 RA2 RA1 RA0 DVDD2 RA10 BA1 DQM0 DQM1 DVSS RA4 RA5 RA6 DVDD3 RA7 DMVSS
162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109
PIN DESCRIPTON
PIN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
Symbol
IREF PLLVSS LPIOP LPION LPFON LPFIP LPFIN LPFOP JITFO JITFN PLLVDD3 FOO TRO TROPENPWM PWMOUT2 DVDD2 DMO FMO FG DVSS HIGHA0 HIGHA1 HIGHA2 HIGHA3 HIGHA4 HIGHA5 DVSS HIGHA6 HIGHA7 AD7 AD6 AD5 AD4 DVDD3 AD3 AD2 AD1 AD0 IOA0 IOA1 DVDD2 IOA2 IOA3 IOA4 IOA5 IOA6 IOA7 A16 A17 IOA18 IOA19 IOA20 APLLVSS3
Type
Analog Input Ground Analog output Analog output Analog output Analog input Analog input Analog output Analog output Analog input Power Analog output Analog output Analog outpu Analog outpu Power Analog outpu Analog outpu Inout, pull up Ground Inout, pull up Inout, pull up Inout, pull up Inout, pull up Inout, pull up Inout, pull up Ground Inout, pull up Inout, pull up Inout Inout Inout Inout Power Inout Inout Inout Inout Inout, pull up Inout, pull up Power Inout, pull up Inout, pull up Inout, pull up Inout, pull up Inout, pull up Inout, pull up Outpu Output Inout Inout Inout Ground
Description
Current reference input.it generate reference current for data PLL Connect an external 100K resistor to this pin and PLLVSS. Ground for data PLL and related analog circuitry Positive output of the low pass filter Negative output of the low pass filter Negative output of loop filter amplifiter Positive input of loop filter amplifier Negative input of loop filter amplifier Positive output of loop filter amplifier RF jitter meter output Negative input of the operation amplifier for RF jigger meter Power for data PLL and related analog circuitry Focus servo output. PDM output of focus servo compensator Tracking servo output.PDM output of tracking servo compensator Tray open output,controlled by microcontroller. This is PWM output for TRWMEN27hRW2=1 or is digital output for TRWMEN27Hrw2=0 The general PWM output 2.5V power Disk motor control output.PWM output Feed motor control. PWM output Motor Hall sensor input Ground Microcontroller address 8 Microcontroller address 9 Microcontroller address 10 Microcontroller address 11 Microcontroller address 12 Microcontroller address 13 Ground Microcontroller address 14 Microcontroller address 15 Microcontroller address/data 7 Microcontroller address/data 6 Microcontroller address/data 5 Microcontroller address/data 4 3.3V power Microcontroller address/data 3 Microcontroller address/data 2 Microcontroller address/data 1 Microcontroller address/data 0 Microcontroller address 0/GPIO0 Microcontroller address 0/GPIO1 2.5V power Microcontroller address 0/GPIO2 Microcontroller address 0/GPIO3 Microcontroller address 0/GPIO4 Microcontroller address 0/GPIO5 Microcontroller address 0/GPIO6 Microcontroller address 0/GPIO7 Flash address 16 Flash address 17 Flash address 18 / GPIO10 Flash address 19 / GPIO11 Flash address20 / GPIO12 Ground
9
PIN
55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113
10
Symbol
APLLVDD3 ALE IOOE# IOWR# IOCS# DVSS UP1_2 UP1_3 UP1_4 UP1_5 UP1_6 DVDD3 UP1_7 UP3_0 UP3_1 INT0# IR DVDD2 UP3_4 UP3_5 UWR# URD# DVSS RD7 RD6 RD5 RD4 DVDD2 RD3 RD2 RD1 RD0 RWE# CAS# RAS# RCS# BA0 DVSS RD15 RD14 RD13 RD12 DVDD3 RD11 RD10 RD9 RD8 DVSS CLK CLE RA11 RA9 RA8 DMVDD3 DMVSS RA7 DV33 RA6 RA5
Type
Power Inout,pull up Inout Inout Inout,pull up Ground Inout,pull up Inout,pull up Inout,pull up Inout,pull up Inout,pull up Power Inout,pull up Inout,pull up Inout,pull up Inout,pull up Input Power Inout Inout Inout,pull up Inout,pull up Ground Inout Inout Inout Inout Power Inout Inout Inout Inout Output Output Output Output Output Ground Inout,pull up/down Inout,pull up/down Inout,pull up/down Inout,pull up/down Power Inout,pull up/down Inout,pull up/down Inout,pull up/down Inout,pull up/down Ground Output Output Output Output Output Power Ground Output Power Output Output
Description
3.3V power Microcontroller address latch enable Flash output enable,active low /GPIO13 Flash write enable,active low /GPIO17 Flash chip select,active low /GPIO18 Ground Microcontroller port 1-2 Microcontroller port 1-3 Microcontroller port 1-4 Microcontroller port 1-5 Microcontroller port 1-6 3.3V power Microcontroller port 1-7 Microcontroller port 3-0 Microcontroller port 3-1 Microcontroller interrupt 0,active low IR control signal input 2.5V power Microcontroller port 3-4 Microcontroller port 3-5 Microcontroller write strobe,active low Microcontroller read strobe,active low Ground DRAM data 7 DRAM data 6 DRAM data 5 DRAM data 4 2.5V power DRAM data 3 DRAM data 2 DRAM data 1 DRAM data 0 DRAM write enable,active low DRAM column address strobe,active low DRAM row address strobe,active low DRAM chip select,active low DRAM bank address 0 Ground DRAM data 15 DRAM data 14 DRAM data 13 DRAM data 12 Power3.3V DRAM data 11 DRAM data 10 DRAM data 9 DRAM data 8 Ground DRAM clock DRAM clock enable DRAM address bit 11 or audio serial data 3 (channel 7/8) DRAM address 9 DRAM address 8 3.3V power Ground DRAM address 7 3.3V power DRAM address 6 DRAM address 5
PIN
114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172
Symbol
RA4 DVSS DQM1 DQM0 BA1 RA10 DVDD2 RA0 RA1 RA2 RA3 DVSS RD31 RD30 RD29 RD28 DVDD3 RD27 RD26 RD25 RD24 DVSS DQM3 DQM2 RD23 RD22 DVDD2 RD21 RD20 RD19 RD18 DVSS RD17 RD16 ABCK ALRCK DVDD3 ACLK MC_DAT SPDIF ASDATA0 ASDATA1 ASDATA2 MUTE ASDATA4 DACV33C VREF FS YUV0/CIN DACVSSC YUV1 DACVDDB YUV2 DACVSSB YUV3/CVBS DACV33A YUV4/G DACVSSA YUV5/B
Type
Output Ground Output Output Output Output Power Output Output Output Output Ground Inout,pull up/down Inout,pull up/down Inout,pull up/down Inout,pull up/down Power Inout,pull up/down Inout,pull up/down Inout,pull up/down Inout,pull up/down Ground Output Output Inout,pull up/down Inout,pull up/down Power Inout,pull up/down Inout,pull up/down Inout,pull up/down Inout,pull up/down Ground Inout,pull up/down Inout,pull up/down Output Input,pull down Power Inout Input Output Input,pull down Input,pull down Input,pull down Output Input,pull down Power output Ground Output Power Output Ground Output Power Output Ground Output
Description
DRAM address 4 Ground Mask for DRAM input/output byte 1 Mask for DRAM input/output byte 0 DRAM bank address 0 DRAM address 10 2.5V power DRAM address 0 DRAM address 1 DRAM address 2 DRAM address 3 Ground DRAM data 31 DRAM data 30 DRAM data 29 DRAM data 28 3.3V power DRAM data 27 DRAM data 26 DRAM data 25 DRAM data 24 Ground Mask for DRAM input/output byte 3 Mask for DRAM input/output byte 2 DRAM data 23 DRAM data 22 2.5V power DRAM data 21 DRAM data 20 DRAM data 19 DRAM data 18 Ground DRAM data 17 DRAM data 16 Audio bit clock (1) Audio left/right channel clock (2)Trap value in power-on reset. 1:use external 373, 0:use internal 373 3.3V power Audio DAC master clock (384/256 audio sample frequency) Microphone serial input SPDIF output Audio serial data 0 (left/right channel) Audio serial data 1 (surround left/surround right channel) Audio serial data 2 (center/LFE channel) Audio Mute Signal Audio serial data 4 3.3V power
Ground Video data output bit 1 3.3V Power Video data output bit 2 Ground CVBS video output 3.3V power Video data output bit 4 Ground Video data output bit 5
11
PIN
173 174 175 176 177 178 179 182 185 186 187 188 189 195 196 197 198 199 200 202 203 204 205 206 207 208 209 210 211 212 215 216 MT1336
Symbol
YUV6 ICE FS1 VSYN YUV7 DVSS HSYN DVDD2 DVDD3 XTALO XTALI PRST DVSS SDATA SDEN SLCK BDO ADCVSS ADIN TEZISLV TEI CSO FEI RFLEVEL RFRP_DC RFRP_AC HRFZC PWMVREF PWM2VREF ADCVDD3 RFIN RFIP
Type
Output Input,pull down output Inout Output Ground Inout Power Power Output Input Input,pull down Ground Output Output Output Input,pull down Ground Analog input Analog input Analog input Analog input Analog input Analog input Analog input Analog input Analog input Analog input Analog input Power Analog input Analog input
Description
Video data output bit 6 Microcontroller ICE mode enable Vertical sync / GPIO16 Video data output bit 7 Ground Horizontal sync / GPIO15 2.5V power 3.3 power Crystal output Crystal input,27MHz Power on reset input, active high Ground RF serial data input RF serial data latch enable RF serial clock output Flag of defect data status input Ground General A/D input Tracking error zero crossing low pass input Tracking error input Central servo input Focus error input Sub beam add input or RFRP low pass input RF ripple detect input RF ripple detect input (through AC coupling) High frequency RF ripple zero crossing A reference voltage input for PWM circuitry.A typical value of 2.8v A reference voltage input for PWM circuitry.A typical value of 1.4v 3.3V power Negative input of RF differential signal Positive input of RF differential signal
GENERAL DESCRIPTION MT1336 is a high performance CMOS analog front-end IC for both CD_ROM driver up to 48xs and DVD-ROM driver up to 16xs. It also supports DVD-RAM read up to 4xs Version 2. It contains servo amplifiers to generate focusing error, 3-beam tracking error, 1 beam radial push-pull signal, RF level and SBAD for servo functions. It also includes DPD tracking error signal for DVD_ROM application. For DVD-RAM disks, there are also Differential Push-Pull (DPP) method for generating tracking signal and Differential Astigmatic Detection (DAD) for processing focusing signal. Programmable equalizer and AGC circuits are also incorporated in this chip to optimize read channel performance. In addition, this chip has dual automatic laser power control circuits for DVD-ROM (DVD-RAM) and CD-ROM seperately and reference voltage generators to reduce external components. Programmable functions are implemented by the access of internal register through bi-directional serial port to configure modes selection. FEATURES . RF equalizer with programmable fc from 3MHz to 70MHz and programmable boost from 3db to 13db. . MT1336 supports at least eight different kinds of pick-up heads with versatile input configuration for both RF input stages and servo signal blocks. . Versatile on-line AGC. . 3 beams tracking error signal generator for CD_ROM application. . One beam differential phase tracking error (DPD) generator for DVD_ROM application. . Differential push pull tracking error (DPP) generator for DVD_RAM application.
12
. Focusing error signal generator for CD-ROM, DVD-ROM and DVD-RAM (DAD method). . RF level signal generator. . Sub-beam added signal for 3 beams CD_ROM. . One beam push-pull signal generator for central servo application. . High speed RF envelop detection circuit with bandwidth up to 400KHz for CD-ROM. . Defect and Blank detection circuits . Dual automatic laser power control circuits with programmable level of LD monitor voltage. . Vref-1.4V voltage and V2ref=2.8V voltage generators. . V20=2.0V voltage for pick-up head reference. . Bi-directional serial port to access internal registers. . 128-pin LQFP Block Diagram..P.3 Pin Assignment and Description..P.4-9 Functions 1.) RF Path Description.P. 10-13 2.) Servo Signal..P. 14-17 . Focusing Error . Central Servo . Tracking Error . RFLVL & SBAD (LVL) 3.) ALPC & RFRP ( RF Ripple).P. 18 4.) WOBBLE Detection..P. 19 Command Access TimingsP. 20 Programmable I/O P. 21 Register 1.) Register Map.P. 22-24 2.) Register Description.P. 25-50 MT1336 PIN DESCRIPTIONS Description Flag of bad data output status RF serial clock input RF serial data enable RF serial data IO Reset (active high) 16.9MHz for verification Control signal for DVD-RAM Control signal for DVD-RAM DVD-RAM Header signal AC coupled DVD RF signal input A AC coupled DVD RF signal input B AC coupled DVD RF signal input C AC coupled DVD RF signal input D AC coupled DVD RF signal input RFIN
13
Pin Numbers Symbol LQFP128 RF Flag interface 23 DEFECT RF SIO interface 56 SCLK 58 SDEN 59 SDATA 60 RST 55 XCK16M RF SERVO interface 40 UDGATE 41 IDGATE 38 VFO13 RF 100 DVDA 99 DVDB 98 DVDC 97 DVDD 95 DVDRFIN
Type Digital input Digital input Digital input Digital IO Digital input Digital input Digital input Digital input Digital input
Analog input Analog input Analog input Analog input Analog input
96 DVDRFIP Analog input AC coupled DVD RF signal input RFIP 94 CDA Analog input AC coupled CD RF signal input A 93 CDB Analog input AC coupled CD RF signal input B 92 CDC Analog input AC coupled CD RF signal input C 91 CDD Analog input AC coupled CD RF signal input D 90 OSN Analog RF Offset cancellation capacitor connection 89 OSP Analog RF Offset cancellation capacitor connection 85 CEQP Analog RF Offset cancellation capacitor connection 84 CEQN Analog RF Offset cancellation capacitor connection 88 RFGC Analog RF AGC loop capacitor connecting for DVD-ROM 87 RFGCU Analog RF AGC loop capacitor connecting for DVD-ROM 86 RFGCI Analog RF AGC loop capacitor connecting for DVD-ROM 101 MA Analog input DC coupled DVD-RAM main-beam RF signal input A 102 MB Analog input DC coupled DVD-RAM main-beam RF signal input B 103 MC Analog input DC coupled DVD-RAM main-beam RF signal input C 104 MD Analog input DC coupled DVD-RAM main-beam RF signal input D 105 SA Analog input DC coupled DVD-RAM sub-beam RF signal input A 106 SB Analog input DC coupled DVD-RAM sub-beam RF signal input B 110 SC Analog input DC coupled DVD-RAM sub-beam RF signal input C 111 SD Analog input DC coupled DVD-RAM sub-beam RF signal input D 108 IR Analog External current bias resistor (R=20K) 119 AGC1 Analog Wobble AGC loop1 capacitor 121 AGC2 Analog Wobble AGC loop2 capacitor 122 AGC3 Analog Wobble AGC loop3 capacitor 127 RFSUBO Analog output Header push-pull RF output signal 1 WOBSO Analog output Wobble signal output 6 RFOP Analog output RF positive output 7 RFON Analog output RF negative output TRACKING ERROR 32 DPFN Analog DPD amplifier negative input 33 DPFO Analog DPD amplifier output 61 DPDMUTE Digital input DPD mute control input 116 TNI Analog input 3 beam satellite PD signal negative input 115 TPI Analog input 3 beam satellite PD signal positive input 21 TEO Analog Output Tracking error output FOCUSING ERROR & RF LEVEL & CENTRAL SERVO SIGNAL 112 CDFOP Analog input CD focusing error positive input 113 CDFON Analog input CD focusing error negative input 18 FEO Analog output Focusing error output 19 LVL Analog output RF level output 20 CSO Analog output Central servo signal output ALPC 124 MDI1 Analog input Laser power monitor input 125 LDO1 Analog Output Laser driver output 123 MDI2 Analog input Laser power monitor input 126 LDO2 Analog Output Laser driver output RF RIPPLE 26 CRTP Analog RF top envelop filter capacitor connecting 27 CRTPLP Analog Defect level filter capacitor connecting 25 HRFRP Analog output High frequency RF ripple output or Blank detectors output 24 LRFRP Analog output Low frequency RF ripple output POWER 67,69 AVDD Power Master PLL Filter power 65,73 AGND GND GND for Master PLL Filter 64 AVDD Power DPD Power 62 AGND GND DPD GND 109 AVDD Power RF path Power 107 AGND GND RF path GND 114 SVDD Power Servo Power 117 SGND GND Servo GND 2,120 WAVDD Power Wobble Power
14
128,118 WAGND GND 5 AVDDO Power 8 AGNDO GND 14 AVDDT Power 12 AGNDT GND 22 VDDP Power 31 GNDP GND 37,54 VDD Power 39,57 GND GND REFERENCE VOLTAGE 16 VREFO Analog output 15 V2REFO Analog output 17 V20 Analog output ALPC TRIMMING 9 TM1 Analog input 10 TM2 Analog input 11 TM3 Analog input 13 TM4 Analog input HIGH SPEED TRACK COUNTING 29 TRLP Analog 28 TRLPA Analog 30 HTRC Digital output PCS 74 HALLSIN Analog input 75 REFSIN Analog input 76 SINPHI Analog output 71 HALLCOS Analog input 72 REFCOS Analog input 70 COSPHI Analog output FOR MONITOR ONLY 81 MON Analog output 80 MOP Analog output 66 VCON Analog output 77 SWO Analog output 78 SW2 Analog input 79 SW1 Analog input FOR SERIAL I/O 42 IO0 43 IO1 44 IO2 45 IO3 46 IO4 47 IO5 48 IO6 49 IO7 50 IO8 51 IO9 52 IOA 53 IOB
Wobble GND Power for RF output GND for RF output Power for trimming PAD GND for trimming PAD Peak Detection Power Peak Detection GND Serial I/O Power Serial I/O GND Reference voltage 1.4V Reference voltage 2.8V Reference voltage 2.0V Trimming pin for ALPC1 Trimming pin for ALPC1 Trimming pin for ALPC2 Trimming pin for ALPC2 Low-pass filter capacitor connecting Low-pass filter capacitor connecting High speed track counting digital output Negative input of amplifier for hall sensor signal Positive input of amplifier for hall sensor signal Amplifier output for hall sensor signal Negative input of amplifier for hall sensor signal Positive input of amplifier for hall sensor signal Amplifier output for hall sensor signal
Output from mux of SW1 & SW2 External input for servo input select External input for servo input select
2-1-3 28-Pin, 24-Bit, 192kHz D/A with Volume Control (DA1196) Description
DA1196 is a digital to analog converter especially designed to work with MPEG2/AC3 decoded data In applications such as DVD player, home theatre, set-top box, and digital TV, etc . DA1196 integrated 6 DA channels providing customers a solution of both simplicity and excellent performance.
15
Features
APPLICATIONS . CD, DVD audio . Home theare systems . Set top boxes PIN DESCRIPTIONS
16
2-1-4 Serial EEPROM, 16K (2048 x 8) (24C16) * Features Low-Voltage and Standard-Voltage Operation -5.0 (V CC = 4.5V to 5.5V) -2.7 (V CC = 2.7V to 5.5V) -2.5 (V CC = 2.5V to 5.5V) -1.8 (V CC = 1.8V to 5.5V) Internally Organized 128 x 8 (1K), 256 x 8 (2K), 512 x 8 (4K), 1024 x 8 (8K) or 2048 x 8 (16K) 2-Wire Serial Interface Schmitt Trigger, Filtered Inputs for Noise Suppression Bi-directional Data Transfer Protocol 100 kHz (1.8v, 2.5V, 2.7V) and 400 kHz (5V) Compatibility Write Protect Pin for Hardware Data Protection 8-Byte Page (1K, 2K), 16-Byte Page (4K, 8K, 16K) Write Modes Partial Page Writes Are Allowed Self-Timed Write Cycle (10 ms max) High Reliability - Endurance: 1 Million Write Cycles - Data Retention: 100 Years - ESD Protection: >3000V
17
Automotive Grade and Extended Temperature Devices Available 8-Pin and 14-Pin JEDEC SOIC, 8-Pin PDIP, 8-Pin MSOP, and 8-Pin TSSOP Packages * Pin Configurations
* Pin Description Pin Name A0-A2 SDA SCL WP NC Function Address Inputs Serial Data Serial Clock input Write Protect No Connect
2-1-5 8M-BIT [1Mx8/512Kx16] CMOS FLASH MEMORY FEATURES 1,048,576 x 8/524,288 x 16 switchable Single power supply operation - 5.0V only operation for read, erase and program
operation Fast access time: 70/90/120ns Low power consumption - 50mA maximum active current - 0.2uA typical standby current Command register architecture - Byte/word Programming (7us/12us typical) - Sector Erase (Sector structure 16K-Bytex1, 8K-Bytex2, 32K-Bytex1, and 64K-Byte x15) Auto Erase (chip & sector) and Auto Program - Automatically erase any combination of sectors with
address
Erase suspend/Erase Resume - Suspends sector erase operation to read data from, or program data to, another sector that is not being erased, then resumes the erase.
Status Reply
- Data polling & Toggle bit for detection of program and erase operation completion. Ready/Busy pin (RY/BY) - Provides a hardware method of detecting program or erase operation completion.
18
Sector protection - Sector protect/chip unprotect for 5V/12V system. - Hardware method to disable any combination of sectors from program or erase operations - Tempory sector unprotect allows code changes in previously locked sectors. 100,000 minimum erase/program cycles Latch-up protected to 100mA from -1V to VCC+1V Boot Code Sector Architecture - T = Top Boot Sector - B = Bottom Boot Sector Low VCC write inhibit is equal to or less than 3.2V Package type: - 44-pin SOP - 48-pin TSOP Compatibility with JEDEC standard - Pinout and software compatible with single-power supply Flash
19
All inputs are sampled at the positive going edge of the system clock Burst Read Single-bit Write operation DQM for masking Auto & self refresh 64ms refresh period (4K cycle) 50 Pin TSOP (II) Pin Configuration
21
Block Diagram
Pin Descriptions Symbol CLk CS Name System Clock Chip Select Description Active on the positive going edge to sample all inputs Disables or Enables device operation by masking or enabling all inputs except CLK, CKE and L(U)DQM Masks system clock to freeze operation from the next clock cycle. CKE A0~A10/AP BA RAS CAS WE L(U)DQM DW0-15
22
CKE should be enabled at least one clock + tss prior to new command. Disable input buffers for power down in standby. Row/Column addresses are multiplexed on the same pins. Row address: RA0 ~ RA10, Column address: CA0 ~ CA7 Selects bank to be activated during row address latch time. Selects band for read/write during column address latch time. Latches row addresses on the positive going edge of the CLK with RAS low. Enables row access & precharge. Latches column addresses on the positive going edge of the CLK with CAS low. Enables column access. Enables write operation and Row precharge. Makes data output Hi-Z, t SHZ after the clock and masks the output. Blocks data input when L(U)DQM active. Data inputs/outputs are multiplexed on the same pins.
Column Address Strobe Write Enable Data Input/Output Mask Data Input/Output
Description Power Supply: +3.3V0.3V/Ground Provide isolated Power/Ground to DQs for improved noise immunity.
3. Product Specifications
Playback System DVD Video Video CD (1.1, 2.0, 3.0) SVCD and CVD CDDA CD-ROM with MP3 data PICTURE CD Television Signal System NTSC/PAL Video Performance Video Out 1 Vpp into 75 ohm S-Video Out Y: 1Vpp into 75 ohm C: 0.286 Vpp into 75 ohm D/A Converter 27MHz/10bit Audio Performance Frequency Response DVD: fs 48/96KHz, 4Hz~22/44KHz Video CD: fs 44.1KHz, 4Hz~20KHz Audio CD: fs 44.1KHz, 4Hz~20KHz Output Level Analog: 2Vrms(1KHZ) Digital: 1.15 Vpp D/A Converter 96KHz/24bit S/N Ratio 90dB Connections Coaxial digital out Audio Analog out for 2-channel S-Video out Power Supply Power Source Power Consumption Set Dimensions (W X H X D) Net Weight Gross Weight
X1 X1 X1
23
24
5. Operating Instruction
Please refer to the Users Manual for operation instruction of the system.
25
Disc Compatibility
Some DVD discs may have special requirements for playing, with which this player may not be compatible. Please refer to specifications on individual disc.
DISC TYPE Content Size Total Play time About 2hrs. (Single side & single layer) About 4hrs. (Single side & double layer) About 4hrs. (Double side & Single layer) About 8hrs. (Double side & double layer) About 74 minutes About 300 minutes
DVD
AUDIO/ VIDEO
12CM
How to clean discs Finger prints and dust on surface can affect the sound and picture quality. Clean discs regularly with a soft cotton cloth from disc center to outside.
CD-DA MP3
AUDIO AUDIO
12CM 12CM
Discs types
For sticky dust, wipe it with wet cloth and with dry cloth, Any kind of solvent, such as diluting agent, gasoline, liquid detergent, gasoline liquid detergent anti static aerosol used for vinylon LP, may cause disc damage.
This DVD player can play the following types of discs: Discs other than listed above cannot be player by this player.
This player uses NTSC/PAL color system. It cannot play discs recorded with other systems, such as SECAM.
Keep away from the direct sunshine or any heat source. Do not put discs in damp or dirty places, such as bathroom or near humidifiers. Store discs vertically in disc box and store in a dry place. Piling discs on to top of each other or excess weight load on disc box may cause the disc to warp.
The region code for this player is 5, which indicates the applicable. The disc with code number other than 5 cannot be player on this player and screen will indicate the unconformity.
Copyright
According to the related law, DVD discs without proper authorization are not allowed to be copied broadcast cable broadcast, played publicly or rented. As DVD discs are anti-piracy the copied content is distorted.
TV system
26
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
WARNING: Under no circumstances should you try to repair the set yourself, as this would invalidate the guarantee.
Problems
No indication No picture power
Cause
Power plug not connected TV has not been set to the correct video input Video cable not firmly connected. Audio cable not connected tightly
Solution
Plug the power cord into the power supply Set correct TV video input format for receiving the players output signals. Firmly insert the video cable ends to the related terminals. Firmly insert the audio cable ends to the related terminals. Turn on the power of audio apparatus. Setup audio output correctly via the setup menu. Take out the disc and clean. The picture may be distorted during fast forward /backward playback. Connect the player directly to TV. Load a disc. Load a compatible disc (Check the disc format and its colour system). Load a compatible disc (Check the disc format and its colour system). Check disc is put in correctly. Clean the disc. Change the setting via the setup menu. Disable this function or reset the rating level. Turn off the main switch or pull out the power plug, plug it in and turn on the power again. Point the remote control at the remote sensor. Make sure the remote control range within 7 meters to the remote sensor. Replace with new batteries.
No sound
Power of audio apparatus is off Audio output setting is incorrect Disc is dirty
Fast forward/backward is activated Affected by anti-piracy circuit No disc Disc not compatible
The disc is placed upside down The disc not put in the tray correctly Disc is dirty Player setting are incorrect Parental lock is in effect Interference of power wave or other factors such as static interference The remote control not pointed at the remote sensor on the front panel of the player The remote control is out of specified range Battery power exhausted
This produce incorporates copyright protection technology that is protected by method claims of certain of certain U.S. patent and other intellectual Property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing users only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Note:
27
28
29
7.Troubleshooting
No power No picture No sound Distorted sound Insert the AC power plug securely into the power outlet. Make sure that the equipment is connected properly. Make sure that the input setting for TV is Video (AV). Make sure that the equipment is connected properly. Make sure that the input settings for the TV and stereo system are correct. Some discs may have sections that prohibit fast forward or fast reverse. Select the correct setup for TV aspect ratio that matches your TV set. Check the batteries are installed with the correct polarities. No operations can be performed with Point the remote control unit at the remote control sensor and operate. Remove the obstacles between the remote control unit and remote control the remote controller sensor. Set the POWER button to OFF and then back to ON. No button operation Alternatively, turn off the power, disconnect the power plug and then reconnect it. If the audio soundtrack and /or subtitle language does not exist on the Audio soundtrack and/or Subtitle disc, the language selected at the initial settings will not be seen. language is not the one you selected. This function is dependent on software availability. Even if a disc has a No Angle change number of angles recorded, these angles may be recorded for specific scenes only. No fast forward or fast reverse No proper aspect ratio
30
TV-5
1
31
fastening wire fastening wire 3 loader sets CO-DJD1379XE+SANYO 5.1CH MPEG board
DS-600MA DVD loader
MTK1379GE 5.1channel
SANYO
DVD loader
CO-DOB1379-9
1 1 2 ABS silver ABS silver ABS silver PVC for SANYO loader ABS silver black ground silver chars 5 for power board,3 for output board
4 keys set mirror transfering bar disc tray DVD logo stick PCB support
32
CO-602 CO-602
8 plastical bolt cap rubber mat rubber mat 5 metals 12*2 19.5*9.5*3.5 8 2 2 5 for power board,3 for output board hardness 64 hardness 64
1 1 1 12 8 8
siver silver-gray black 9 for control panel,2 for power botton,1 for bracket 8 for Audio output jack 5 for power board, 3 for AV output board 4 for upper cover, 4 for rear panel,3 for front panel 4 for loader 2 for rear panel 3 for MPEG board 2 for front panel side
bolt
3*6WBHE
11
bolt bolt
4 2 3 2
bolt
bolt
1 1 1 1 1 1 1 players in 1 PE for power supply wire for remote control for owner's manual pearl cotton
PH-919 manual
Video connection wire Audio connection wire Cothers serial stick 7 others solder tin heat-melting-glue red glue yellow glue black glue heat-dissipating oil
34
glue paper heat-contracting tube heat-contracting tube jumper0.6mm double-color LED 8 Components of Power Board Jack Jack Jack Jack Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Electrolytic capacitor Electrolytic capacitor Electrolytic capacitor Electrolytic capacitor Electrolytic capacitor Electrolytic capacitor Electrolytic capacitor( high frequency) 4PIN/2.54mm 5PIN/2.54mm 10PIN/2.54mm 3PIN/3.96mm 330pF 63V +/-10% 5mm 0.1uF 63V +/-20% 5mm 100pF 63V +/-20% Y5P 5mm 10nF 1KV +/_%10 5mm 220UF 16V +/-20% 6X11mm 470UF 16V +/-20% 8X11mm 330UF 25V +/-20% 8X14mm 470UF 25V +/-20% 8X12mm 100UF 50V +/-20% 8X14mm 47UF 400V +/-20% 22X23mm 1000uF 10V +/-20% 3mm 4mmX15mm 22X30mm
some 2 1 1 1
1 1 1 1 1 1 3 1 1 1 2 2 2 1 2
Safety Regulation capacitor Safety Regulation capacitor Safety Regulation capacitor Polyester capacitor Ceramic capacitor Diode Diode Diode Schottky Diode Schottky Diode Zener Diode Fuse Fuse Jack Bead Inductor(I-shape) Inductor(I-shape) Common-mode Inductor Transformer Carbon Film Resistor Carbon Film Resistor
36
680UF 400V +/-20% Y1 2200UF 400V +/-20% Y1 UL 10mm 0.1UF 275V +/-10% 15mm 47nF 100V +/-10% Y5P 5mm 0.1uF 50V +/-20% 5mm IN4007 IN5404 SR560 HER107 UF4007 3.3V 1/2W T2A T-D 250V PL UL CSA VDE BLX-A 3.5X4.7X0.8mm 1A 10UH P5MM D6MM 2A 10UH P5MM D6MM >10mH R<4.5E CO-BYBYDAP118A/B/C KBEC28-0325 2W 27K +/-5% 1W 1E +/-5%
1 2 2 2 2 4 2 1 5 1 1 1 1 2 2 1 1 1 1 1
BC6 BC3,BC4 BC1,BC2 C2,C3 C4,C5 D1,D2.D3,D4 D13,D14 D10 D6,D7,D8,D9,D12 D5 DZ1 F1 F501 L2,L3 L4,L7 L5 L1 T1 R7 R6
Carbon Film Resistor Carbon Film Resistor Carbon Film Resistor Carbon Film Resistor Carbon Film Resistor Carbon Film Resistor Carbon Film Resistor Carbon Film Resistor Press-sensitive Resistor Grounding solder slice IC IC Photo-electric Couple Power Board PCB Jumper Jumper Jumper 9 Components of Control Panel Carbon Film Resistor Carbon Film Resistor Carbon Film Resistor Ceramic capacitor
1/4W 10K +/-5% 1/4W 300E +/-5% 1/4W 3K +/-5% 1/4W 470E +/-5% 1/4W 4.7K +/-5% 1/4W 5.1K +/-5% 1/4W 6.8K +/-5% 1/4W 75K +/-5% 07 471 D3.2 mm TEA1523P TL431 TO-92 decal PC817 C0-DPB118 2002-09-09 10mm 15mm 16mm
2 1 1 1 1 1 1 1 1 3 1 1 1 1 2 1 1
2 7 1 1
R1R9 R2~R4R6~R8R10 R5 C3
37
50V104 +80/-20%
16V
47UF
20%
2 5 1 1 1 10 2 4 2 3 2 2 1 1 1 1
C1,C2 D1,D2,D3,D4,D5 U1 IC1 RMC1 NEXT STOP PREV OPEN REV FWD PAUSEPLAYSTOP1PLAY1 VOL1,VOL2 JMP1JMP3JMP6JMP17 JMP7JMP8 JMP2JMP15JMP16 JMP5JMP11 JMP4JMP9 JMP10
Potentiometer Jumper Jumper Jumper Jumper Jumper Jumper sponge mat for R/M sponge mat for VFD PCB
RV0902N-15FD1-A20K-P
9. Block Diagram
38
39
40
1. Control Part
1 2 3 4 5 6
+5V 35 36 37 38 39 40 41 42 43 44 IC1 SEG15 SEG14 GRID8 GRID7 GRID6 GRID5 GRID4 GRID3 GRID2 GRID1 52 45 33 14 +5V 5 6 8 9 REMOTE 34 51 1 2 3 4 1 2 3 4 5 6 6PIN R5 51K C1 47U/16V OSC VDD VDD VDD DOUT DIN CLK STB UPD16311 VEE VSS SW1 SW2 SW3 SW4
G1 G2 G3 G4 G5 G6 G7 G8 G9 G10
35 34 33 32 31 30 29 28 27 26
37 36 25 24 23 4 3 39 F2 38 F1 2 1
NP NP NP NP NP NP NP F2 F2 F1 F1 IC3 GVGD
22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15
SEG16 SEG17 SEG18 SEG19 SEG20 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1
CN1
R4 10K
R8 10K +5V
R10 10K
D1 DIODE
D2 DIODE
D3 DIODE
D4 DIODE
-27V 13 12 11 10 7 50 49 48 47 46
C2 47U/50V REMOTE 3 2 1 +5V SIG GND VCC RMC1 B CN2 F2 F1 -27V GND 1 2 3 4 4PIN
STOP5 KEY
NEX1 KEY
KEY
STOP9 KEY
STOP3 KEY
STOP4 KEY
STOP1 KEY A
41
2. INDEX
1 2 3 4 5 6
Servo-MPEG Board of MAXITECH Complete Loader DCL34MK72/75MT1379xE for Cosmic DV-34 Pickup Loader
Background
D
Revision History
Revision-A1
D
This design is the Servo-MPEG Board of COSMIC Technology Co., LTD. DVD Complete Loader module DCL34MK-72/75, which is thecombination of this PCBA & Cosmic DV-34 Pickup Loader.
Base on MTK Reference Design COMMON79_HD60_V2,Re-sized for Complete Loader PCB Dimension Requirement. This design is based on MTK second generation MT1379xE super integration DVD chipset. The MT1379xE is built upon MTK's proven previous MT1369xE super integration chipset. It supported all MT1369xE generation features plus new features including Progressive Scan output with built-in very high performance 6-channdel 12 bit TV-Encoder (Macrovision compliance) and Dolby ProLogic II surround sound processing. With the chipset's highest integrity, a complete DVD design can now be implemented with minimum chip count & external components. FSG@COSMICTEC.COM
Revision-A2 1. Add Audio ADC, DA1196 Software Control Mode Option. 2. 1Mx16 SDRAM Connection Data DQ[16:31] Changed. PCB Layout GRANGER-A2B1
Revision-A3 1. Based on Rev-A2, Video Output Buffer Added. 2. VFD Interface I/O Changed. 3. Fixed Some KnownErrors. PCB Layout GRANGER-A3B2
Memories Required
The current MT1379xE requires 8M bit Flash for DVD code storage & slow speed code running. For SDRAM, only 4M byte space is required. This provides a lower cost option to use 2 pieces 1Mx16 SDRAM with 32bit data width. The other option is to use one single piece of higher density 4Mx16 SDRAM & the extra memory space will be used as track buffer for better anti-shock function.
Revision-A4 1. Based on Rev-A3, VFD Interface STB Signal Changed from P1.2 to P1.3.
System Configuration
C
1. Some Ferrite Beads on Power Supply Path Changed fromSMD0805 to SMD1206. FUNCTION Super integration chip that handles all Servo, Read Channel, DVD Decoding and system control. Built-in TV-Encoder direct drives a TV set. PCB Layout GRANGER-A4B3
C
CHIP MT1379xE
MT1336E 32/64MBit SDRAM 8Mbit FLASH 24C02 SERIAL EEPROM DA1196/DA1131 BA5954FP BA6208F
Analog front end CMOS IC for MT13x9E DVD chip. Data storage and frame buffer Program storage System setup configuration storage 6-Channel/2-Channel AudioDAC DVD pickup actuators & Traverse motors driver Disc loading tray motor driver.
AUX I/O Port 8032 Core P1.2 8032 Core P1.3 8032 Core P1.4 8032 Core P1.5 8032 Core P1.6 8032 Core P1.7 8032 Core P3.0
B
FUNCTION Reserved for 16Mbit Flash Bank Switch Control Front Panel Display Driver Serial Interface Strobe Signal Front Panel Display Driver Serial Interface Data Signal Sapre I2C Bus Serial Clock & Front Panel Display Driver Serial Interface Clock Signal I2C Bus Serial Data Signal Spare Spare 8032 Core Interrupt#0, Chip Intrenal Use. 8032 Core Interrupt#1, Infrared Remote Control Serial Data Receive. 8032 Core RS-232 port RxD Signal. 8032 Core RS-232 port TxD Signal. 8032 Core Write Enable Signal, Chip Internal Use. 8032 Core Read Enable Signal, Chip Internal Use.
B
8032 Core P3.1 8032 Core P3.2 8032 Core P3.3 8032 Core P3.4 8032 Core P3.5 8032 Core P3.6 8032 Core P3.7
EAUXx MT1379E Pin 157 MT1379E Pin 158 MT1379E Pin 175 MT1379E Pin 176 MT1379E Pin 177 MT1379E Pin 179 MT1336E IO0:4 MT1336E IO5 MT1336E IO6 MT1336E IO7
A
FUNCTION Audio Output MUTE Control Signal. Not Used. SCART Control Signal FS1. Video Horizontal Synchronization Signal HSYNC# or SCART Control Signal RGB/Video Switch. MIC MUTE Control Signal. Video Vertical Synchronization Signal VSYNC# or SCART Control Signal FS0. Not Used Disc Loading Tray In Position Limit Switch Detect. Disc Loading Tray Out Position Limit Switch Detect. Pickup Head Home Position Limit Switch Detect. Motor Driver Stand-by Control. ENDM Pickup Head CD/DVD Switch. Disc Loading Tray Close Drive Signal.
A
42
3.SERVO&RF
1 2 3 4 5 6
L1
Ferrite Bead
1206
DV33
+PS5V
C6 220u 1
CB11 0.1u
C151 220u
CB8 0.1u
C9 220u
L3
Ferrite Bead
1206
AVCC L31
1206
TROPEN TROPEN
8 7 6 5
Ferrite Bead
NOT STUFF
5 4 3 2 1
R146 10K
U1 1117-3.3 IN 3
SOT-223 NOT Stuffed
PWMOUT2 PWMOUT2
OUT
10K
RFVCC
L33 FB 0805
NOT STUFF
D6 1N4001
NOT Stuffed
SCLK
RVCCIN 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 000 VFO13 VDD AGNDX AGNDX AGNDX DPFO DPFN GNDP HTRC TRLP TRLPA CRTPLP CRTP HRFRP LRFRP DEFECT VDDP TEO CSO LVL FEO V20 VREFO V2REFO AVDDT TM4 AGNDT TM3 TM2 TM1 AGNDO RFON RFOP AVDDO AGNDX AGNDX WVDD WOBSO 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R153
C148 47u
U17
C128 100u
CB77 0.1u
C136 47u
C140 47u
OPO OPOP+ LDO1
CB97 0.1u
C
LDO2
SW1
D4 1N4148 GND-LD LD-DVD NC HFM MD LD-CD VR-DVD VR-CD NC E VCC VC GND-PD F B A RF CD/DVD D C TT+ F+ F1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 CB90 0.1u B
CB1 0.1u
L35 10uH
L36 10uH
CB2 0.1u
D5 1N4148
CB82 0.1u
500pF forMT1376
MDI
L34 FB 0805
AVCC
+
RFO D A B C
C138 10u
R148 10K
IOA
MC MD SA SB AGND IR AVDD SC SD CDFOP CDFON SVDD TPI TNI SGND WGAND AGC1 WAVDD AGC2 AGC3 MDI2 MDI1 LDO1 LDO2 RFSUBO WGND
AGNDF VCON AVDDF AGNDX AVDDM COSPHI HALLCOS REFCOS AGNDM HALLSIN REFSIN SINPHI SW0 SW2 SW1 MOP MON AGNDX AGNDX CEON CEOP RFGCI RFGCU RFFGC OSP OSN CDD CDC CDB CDA DVDRFIN DVDRFIP DVDD DVDC DVDB DVDA MA MB
AVDDP AGNDX AGNDP DPDMUTE RST SDATA SDEN GNDS SCLK XCK16M VDDS IOB IOA IO9 IO8 IO7 IO6 IO5 IO4 IO3 IO2 IO1 IO0 HDGATE UDGATE GND
AVCC
LRFRP
RES
SW1
C129 R157
HTRC
HTRC C131 C132 BDO RFRP TEO CSO RFL FEO C133 10p
C130 R158
15n 100K
MT1336E
V2P8
V1P4
C18 10u
CB29 0.1u
CB88 0.1u
C16 10u
CB85 0.1u
RFON
CB89 0.1u
CB109 0.1u
CON1 SF-HD60AV/0.5mm,24Pin
CB80 0.1u
CB107 0.1u
R152 100K
R147 100K
R151 10K
F
LDO1
LDO2
MDI
103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
R165 33K
15K forMT1376
CB78 0.1u
CB79 0.1u
C147 15n
R163 1Ohm
R164 1Ohm 14 13 12 11 10 9 8 30
U18 VOFC+ VOFCVOSL+ VOSLPGND PVCC1 VCC GND VNFFC VOSL VINSLVINSL+ CF2 CF1 VINFC
BA5954 VOTK+ VOTKVOLD+ VOLDPGND VNFTK PVCC2 GND PREGND VINLD CTK2 CTK1 VINTK BIAS STBY 15 16 17 18 19 20 21 29 22 23 24 25 26 27 28 CB96
R161 1Ohm
RES C2
OPO OPOP+
DV33
+
SPSP+
R170 +PS5V
750K
CB10
0.1u
ADIN
10u
URST
URST
R167 10K
CB95 20K
0.1u
C150 FOSO
150p
R169
7 6 5 4 3 2 1
R166
20K
C149
150p
FMSO TRSO
SPSP+
R173 330K
R171 750K
R1 10K
D1 1N4148
V1P4 STBY
C137 10u
C153 47u
LIMIT SLSL+
0.1u
V1P4
GND_POWER
43
+PS5V SD33
+PS5V
U6
SDRAM 512Kx16x2
U7
2 3 5 6 8 9 11 12 39 40 42 43 45 46 48 49
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 SDCLK SDCKE DCS# DRAS# DCAS# DWE# DQM3 DQM2 MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 BA0
SDRAM 512Kx16x2
U5
SDRAM 1Mx16x4
R6
SMD 0805
R26
R27
P1.3
4.7Ohm
L6 FB 0805
TO FRONT PANEL
10Ohm
10K
DACV33A
CB103 0.1u
SMD 0805
SMD 0603
RN3
33x4
D
L7 FB 0805
1 2 3 4 5 6 7 8 9 10 11 12
R31 R32
RN1
33Ohm 33Ohm
33x4
MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 BA0 SDCLK
21 22 23 24 27 28 29 30 31 32 20 19
35 34
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 BA/A11
CLK CKE
GND
DACV33B
C38 100u
C41 100p
R5 33Ohm
CB102 0.1u
SMD 0805
SMD 0603
18 17 16 15
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
21 22 23 24 27 28 29 30 31 32 20 19
35 34
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 BA/A11
CLK CKE
CS RAS CAS WE
SD33
L8 FB 0805
GND
DACV33C
1
C11 1000p
2 74HCU04 U20A R4
Y1
Reserved
DQM1
14 36
33 37
DQML DQMH
NC NC
1 25 7 13 38 44
4 10 41 47
GND
18 17 16 15
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
2 3 5 6 8 9 11 12 39 40 42 43 45 46 48 49
DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DQ23 DQ22 DQ21 DQ20 DQ19 DQ18 DQ17 DQ16
MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 MA11 BA0 BA1 SDCLK SDCKE DCS# DRAS# DCAS# DWE# DQM0 DQM1
23 24 25 26 29 30 31 32 33 34 22 35 20 21
38 37
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
V1P4 V2P8 BDO ADIN TEO CSO FEO RFL RFON RFOP
V1P4 V2P8
R175
SMD 0603 33Ohm
SMD 0603
HSYNC#
T_CVBS 3A GND
DACV3
ADIN
GND
GND
GND
CSO
BDO
FEO
TEO
DV3 3
DV3
RFL
V25
Y6
Y5
GND
Y4
Y2
Y1
C22
1000p
AV33
RFON RFOP
RFIN RFIP
DACV3
C# FS1
VSYN
3B GND
216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163
RFIP RFIN RFDTSLVN RFDTSLVP ADCVDD3 PWM2VREF PWMVREF HRFZC RFRP_AC RFRP_DC RFLEVEL FEI CSO TEI TEZISLV RFSUBI ADIN ADCVSS BDO SLCK SDEN SDATA WOBSI UDGATE DVDD3 IDGATE VFO13 DVSS PRST XTALI XTALO DVDD3 SPBCK SPLRCK DVDD2 SPDATA SPMCLK HSYN DVSS YUV7 VSYN BLANK# ICE YUV6/R YUV5/B DACVSSA YUV4/G DACVDDA YUV3/CVBS DACVSSB YUV2/Y DACVDDB YUV1/C DACVSSC
P3.1
SMD 0603
APLLVDD3 ALE IOOE# IOWR# IOCS# DVSS UP1_2 UP1_3 UP1_4 UP1_5 UP1_6 DVDD3 UP1_7 UP3_0 UP3_1 INT0# IR DVDD2 UP3_4 UP3_5 UWR# URD# DVSS RD7 RD6 RD5 RD4 DVDD2 RD3 RD2 RD1 RD0 RWE# CAS# RAS# RCS# BA0 DVSS RD15 RD14 RD13 RD12 DVDD3 RD11 RD10 RD9 RD8 DVSS CLK CLE RA11 RA9 RA8 DMVDD3
SMD 0603
SMD 0603
SMD 0603
DV33
1206
AV33
AV33
R29
CB3 0.1u
4.7Ohm
V25
DV SDA 33
GN D
GN DQ7 D
GN
DV
DQ1 33
GN
V25
C4 220u
# CAS#
DCL D
DQ1 D
RAS#
DQ3
RXD
DQ9 0
DCK K
MA1 E
MA9 1
GND
IR
MA8
P1.3
VSD A P1.5
P3.0
P3.1
DQ6
DQ5
DQ4
DQ2
DQ1
DQ0
5 DQ1
4 DQ1
DQ1 3
DQ1 1
DQ8
TXD
SCL
CS#
BA0
WE
44
SMD 0603
SMD 0603
CS RAS CAS WE
14 36
33 37
DQML DQMH
NC NC
SD33 1 25 7 13 38 44
SD33
19 18 17 16
CS RAS CAS WE
1 14 27
3 9 43 49
6 12 46 52
GND_POWER
U20F
74HCU04
Reserved
15 39
36 40
54 41 28
CB27 0.1u
C154 220u
CB30 0.1u
SMD 0603
NOT Stuffed
100K
13
L5 2.7uH
0805
12
GND
26 50
VSS VSS
26 50
GND
VSS VSS
SD33
4 10 41 47
GND
DQML DQMH
NC NC
VSS VSS VSS
SMD 0603
SD33
GND
NOT Stuffed
C13 22p
27MHz
C14 22p
+
GND_POWER
OPTIONAL
C43 47u
CB39 0.1u
CB40 0.1u
CB42 0.1u
CB43 0.1u
CB101 0.1u
CB36 0.1u
CB37 0.1u
CB108 0.1u
URST
U9
GND GND
A19 A18 MICMUTE
8Mbit Flash
RFRP HTRC
RFRP HTRC
CB28 0.1u
SMD 0603
CB87 0.1u
SMD 0603
CB110 0.1u
SMD 0603
R7
SMD 0603 100K
SMD 0603
C21 1000p
R10 18K
SMD 0603
R11
1K
Y1
A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 PWR# PCE#
GND
Y2 Y3 Y4 Y5 Y6 HSYNC# VSYNC#
C23
1000p
U4
SMD LQFP-216
MT1379E
FS1
AV33
A20 P3.0
R14 4.7Ohm
9 16 17 48 1 2 3 4 5 6 7 8 18 19 20 21 22 23 24 25
11 26 28
A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A09 A08 A07 A06 A05 A04 A03 A02 A01 A00
WE CE OE
DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 DQ09 DQ08 DQ07 DQ06 DQ05 DQ04 DQ03 DQ02 DQ01 DQ00
45 43 41 39 36 34 32 30 44 42 40 38 35 33 31 29
A0
C
AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0
FVCC L
C24 47u
CB22 0.1u
R15
SMD 0603
8.2K
SMD 0603
C28
C30
SMD 0603 SMD 0603
10n C29
10n
GND
10n
C31
750K
10n
C33
FOSO TRSO TROPEN
FOSO TRSO TROPEN PWMOUT2 DMSO FMSO
100p
R17
SMD 0603 SMD 0603SMD 0603
R18 R19
20K 18K
V25
R21 R22
SMD 0603 SMD 0603
10K 15K
A8 A9 A10 A11 A12 A13
GND
CB35 0.1u
SMD 0603
C34 15n
SMD 0603
C37 RES
SMD 0603
C35 330p
SMD 0603
C36 330p
SMD 0603
GND
V1P4
DV33
DV33
CB5 0.1u
SMD 0603
CB13 0.1u
SMD 0603
CB14 0.1u
SMD 0603
CB15 0.1u
SMD 0603
CB17 0.1u
SMD 0603
CB18 0.1u
SMD 0603
D12 1N4001
GND
A4 A5 A6 A7
V25
+
V25
A16 A17
C10 220u
CB9 0.1u
GND
CB19 0.1u
SMD 0603
CB20 0.1u
SMD 0603
CB100 0.1u
SMD 0603
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
37 12 13 14
47 27 46
FB 0805
+PS5V DV33
L10 RES
+
L2
SMD 0603
IREF PLLVSS LPIOP LPION LPFON LPFIP LPFIN LPFOP JITFO JITFN PLLVDD3 FOO TRO TROPENPWM PWMOUT1 PWMOUT2 DVDD2 DMO FMO DVSS FG HIGHA0 HIGHA1 HIGHA2 HIGHA3 HIGHA4 HIGHA5 DVSS HIGHA6 HIGHA7 AD7 AD6 AD5 AD4 DVDD3 AD3 AD2 AD1 AD0 IOA0 IOA1 DVDD2 IOA2 IOA3 IOA4 IOA5 IOA6 IOA7 A16 A17 IOA18 IOA19 IOA20 APLLVSS
MT1379_216
GND
YUV0/CIN FS VREF DACVDDC ASDATA4 ASDATA3 ASDATA2 ASDATA1 ASDATA0 SPDIF MC_DATA ACLK DVDD3 ALRCK ABCK RD16 RD17 DVSS RD18 RD19 RD20 RD21 DVDD2 RD22 RD23 DQM2 DQM3 DVSS RD24 RD25 RD26 RD27 DVDD3 RD28 RD29 RD30 RD31 DVSS RA3 RA2 RA1 RA0 DVDD2 RA10 BA1 DQM0 DQM1 DVSS RA4 RA5 RA6 DVDD3 RA7 DMVSS
162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109
R13
DACV33C MUTE ASDAT2 ASDAT1 ASDAT0 ASPDIF AMDAT ACLK DV33 ALRCK ABCK DQ16 DQ17 GND DQ18 DQ19 DQ20 DQ21 V25 DQ22 DQ23 DQM2 DQM3 GND DQ24 DQ25 DQ26 DQ27 DV33 DQ28 DQ29 DQ30 DQ31 GND MA3 MA2 MA1 MA0 V25 MA10 BA1 DQM0 DQM1 GND MA4 MA5 MA6 DV33 MA7
RES
C44 47u
PRD#
CB104 0.1u
CB105 0.1u
CB4 0.1u
15
MUTE ASDAT2 ASDAT1 ASDAT0 ASPDIF ACLK ALRCK ABCK AMDAT
RY_BY
C32 RES
R16
SMD 0603 1.5K
SMD 0603
CB33 RES
GND_POWER
SMD 0603
GND
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 PWR# PRD# PCE#
SMD 0603
R23
SMD 1K 0603
GND
11 10 9 8 7 6 5 4 42 41 40 39 38 37 36 35 34 3 2
43 14 12
IO15 IO14 IO13 IO12 IO11 IO10 IO9 IO8 IO7 IO6 IO5 IO4 IO3 IO2 IO1 IO0
Vcc RESET
31 29 27 25 22 20 18 16 30 28 26 24 21 19 17 15
23 44
A0
FVCC
33 13 32
CB49 RES
CB52 RES
GND_POWER
OPTIONAL
DV33
CB51
0.1u
NOTE:
(for U10) 1. 24C02 for stand-aloneDVD player application;
R25
1 2 3 DC/NC RST_/NC
VCC RST/WP SCL SDA 8 7 6 5
SMD 0603
R24
SMD 0603
1K
1K
SCL SDA
C40 2.2u
0805
C39 2.2u
0805
GND
WP/RST_ 2. 24C04, 24C08 or 24C16 forDVD Mini Hi-Fi, DVD-Receiveretc special application; 4
VSS
U10 GND_POWER
Ferrite Bead
SMD 0603
SMD LQFP-216
AV33
FVCC
R33
10K
R30
hm 4.7O
SMD 0603
5.Audio&Video D/A
1
U12
+5VDD
2
KHTech DA1196
SSOP-28 6 CH DAC for DCL34MK-75
+5VA
+5V
R51
+5V
10Ohm
R52
10Ohm
+5V AMDTA
AMDAT
R177
10Ohm
1
C53 100u
+
DVDD
AVDD1 AVDD2
AGND1 AGND2
15 28
20 24
26 22 18
25
U21
KHTech AD1181
SOP14
CB56 0.1u
CB58 0.1u
CB106 0.1u
+ C55
SALRCK
D
RN5 33x4
NOT Stuffed
9 11
GND_POWER
100u
SABCK SACLK
MUTE DGND
14 13 12 8
2 3 4 5 6 7
R2 R3
GND A
LMAIN RMAIN LREAR RREAR CENT LFE MIC IN 2 MIC IN 1
RES RES
7 6 5 4 3 2 1
8 9 10 11 12 13 14
+ C155
OUT0R
OUT1L
27
21
C157 47u
+ CB111
CB12 0.1u
+ C156
ACLK ABCK ABCK ALRCK ALRCK ASDAT0 ASDAT0 ASDAT1 ASDAT1 ASDAT2 ASDAT2
ACLK
RN2
33x4
0.1u
4.7u
4.7u
OUT1R
OUT2L
23
17
GND_A
R49 R50
33Ohm 33Ohm
GND_A
OUT2R
CAP
19
16
10
LRCLK2
CB57
0.1u
CN7 JST14 Pin 2.0mm Pitch
LMAIN RMAIN
RN4 33x4
C54
+
10u
GND A
C
GND_POWER
LMAIN
+5VDD
U13
KHTech DA1131
SOP14
SACLK
8 9 10 11 12 13 14
7 6 5 4 3 2 1
RMAIN
1 2 3 4 5 6 7 8 9 10 11 12 13 14
CN10 Audio IN
JST6Pin 2.0mm Pitch
SABCK SALRCK MIC IN 2 MIC IN 1
1 2 3 4 5 6
GND A
GND A
GND A
GND_POWER GND A
VVCC
VVCC
VVCC
CB16 0.1u
R58 75Ohm
0805
CVBS1
CB7 0.1u
GND_V
R80 75Ohm
0805
T_SY
CB6 0.1u
GND_V
CVBS2
R94 75Ohm
0805
GND_V
R59 RES
R81 RES
R95 RES
T_SC
ROUT GOUT
Y3Y3
Q4 3906
Y2Y2
Q8 3906
Y1Y1
Q12 3906
R67 160,1%
GND_V
R85 160,1%
GND_V
R97 160,1%
13 12 11 10 9 8 7 6 5 4 3 2 1
GND_V GND_POWER
DV33
VVCC
+5V
L21
FB 0805
+
L22 RES
C95 220u
GND_V
GND_V
VVCC
VVCC
VVCC
VVCC
CB21 0.1u
GND_V
R71 75Ohm
0805
CVBS2
CB25 0.1u
R107 GND_V RES
R104 75Ohm
0805
ROUT
CB23 0.1u
R119 GND_V RES
CB24
R116 75Ohm
0805
0.1u
R130 75Ohm
0805
The information has been checked and is believed to be reliable. However, no responsibility is assumed for inaccuracies. Circuit diagrams are provided as a means of illustrating typical applications; MAXITECH Technology reserves the right to make changes at any time in order to improve the design.
R68 RES
GOUT
R135 GND_V
RES
BOUT
Y3
Q6 3906
Y6Y6
Q15 3906
Y4Y4
Q17 3906
Y5Y5
Q22 3906
GND_V
R108 160,1%
GND_V
R120 160,1%
GND_V
R137 160,1%
GND_V
45
45
6.AV PORT
1 2 3 4 5 6
C101
MIC LIN
C10 10UF
C11 10UF
R13 267K
R10 10K
R11 20K
T-CVBS
10P L1
1.8UH/DIP
CVBS-TV
+12V
R70 680
R71 1K
ASPECT
+P12V
L70 FB
+12V
C13 220P
R12 10K
R14 10K
R15 5.1K
-12V
DAC-ML
U10 UJM4558
+12V A-MUTE
C14 10UF
R17 1K
R16 100
L10 FB
Q10 3904
C79 0.1UF
C80 220UF
ML
C12 2000P
C100 220P
C102 100P
R102 NC
C103 22P
Q70 3904
C15 22P
VGND AGND VGND VGND SCART-TV-SEL
AGND -P12V
L71 FB
C81 0.1UF
D
-12V
R72 2.2K
AGND AGND
C201 10P
R73 33
VGND
C82 220UF
MIC RIN
C20 10UF
C21 10UF
R23 267K
R20 10K
R21 20K
L2
R28
R29
AGND
CVBS-ST
+12V
1.8UH/DIP
Q71
3906
RGB/CVBS#
+P5V
L72 FB
C83 0.1UF
+5V
C23 220P
R22 10K
R24 10K
R25 5.1K
-12V
DAC-MR
U10
C24 10UF
R27 1K
R26 100
L20 FB
Q20 3904
MR
C200 220P
C202 100P
C203 22P
SCART-V-SEL
R74 2.2K
VGND
C70 0.1UF
C84 220UF
C22 2000P
C25 22P
VGND
VGND
C301 10P
L3 1.8UH/DIP
SY
R75 10K
R76 0
R92
AGND
D101 5819
Q74
R31 20K
R77 22K
D100 5819
C71 470UF
Q72 3906
R93
DAC-SL
C31 10UF
R34 10K
C33 220P
R32 10K
R35 5.1K
-12V
C300 220P
C302 100P
C303 22P
3904
U20 UJM4558
+12V A-MUTE AGND
C34
100
R36
L30 FB
Q30 3904
R78 1K
C
R79 1K
A-MUTE VGND
R33 267K
C32 2000P
10UF
R37 1K
C35 22P
C401
C72 220UF
FS1 +12V SC AGND
R94
AGND AGND
AGND T-SC
10P
L4 1.8UH/DIP
C87 0.1UF
C88 0.1UF
AGND
C89 0.1UF
R41 20K
DAC-SR
C41 10UF
R43 267K
C43 220P
R42 10K
R44 10K
R45 5.1K
-12V
C400 220P
C402 100P
C403 22P
D202 4148
-12V
U20
C44 10UF
R47 1K
R46 100
L40 FB
Q40 3904
VGND SR
VGND
VGND
R83 100K
-12V
R84 100K
C90 0.1UF
C91 0.1UF
AGND
C92 0.1UF
C42 2000P
C45 22P
C501 10P
T-R/V
AGND
AGND AGND
AGND
L5 1.8UH/DIP
R/V ASPDIF
R85 100
C74 0.1UF
C75 22P
AGND
AGND COAXIAL
R51 20K
LX
3 2 1
SPDIF
VGND
DAC-CENT
C51 10UF
R53 267K
C53 220P
R52 10K
R54 10K
R55 5.1K
-12V
C500 220P
C502 100P
C503 22P
R86 100
C73 330P
CX
U30
C54 10UF
A-MUTE
R56 100
L50 FB
Q50 3904
AGND
VGND C
VGND
VGND
R87 33
C52 2000P
UJM4558 +12V
C55 22P
CN3
1
R57 1K
C601 10P
T-G/Y
C76
22P
C77 0.1UF
C78 10UF
2 3
1 2 3 4 5
L6 1.8UH/DIP
G/Y
AGND
TO POWER
AGND
C600 220P
C602 100P
C603 22P
1
CN7
R61 20K
VGND
VGND
VGND
C63 220P
DAC-LEF
-12V
C61 10UF
R63 267K
R62 10K
R64 10K
R65 5.1K
U30 UJM4558
C64 10UF
R66 100
L60 FB
C701 10P
C62 2000P
A
AGND
R67 1K
Q60 3904
AGND AGND
C65 22P
T-B/U
L7 1.8UH/DIP
B/U
14
1 2 3 4 5 6 7 8 9 10 11 12 13 14
TO DECORD
DAC-ML DAC-MR DAC-SL DAC-SR DAC-CENT DAC-LFE MICMUTE MUTE ASPDIF +5V
CN8 11 10 9 8 7 6 5 4 3 2 1
CN8
11
1
VGND
11 10 9 8 7 6 5 4 3 2 1 TO SCART2
11
1
VGND
TO DECODER
C700 220P
C702 100P
C703 22P
AGND
CN4 4 3 2 1 TO POWER
VGND
VGND
VGND
+12V AGND R L
10E R90
R90 10E
R89
10E
R91
10E
46
7.Power Part
1 2 3 4 5 6 7 8 CN1
!
AC80~265V BCN1 2 1
!
F1
!
BCN502 POW SW1 L1 D2 BC4 222M 1N4007 D3 BC1 0.1uF/275v BC2 1N4007 BC3 222M D1 1N4007
-21V
!
C9 68uF/450v
C10 220UF/16V C11 C8 R7 HER105 T1 10 D7 D5 HER108 4 11 12 PH-33D C12 100P D9 BYV27-200 L4 10uH C18 470uF/25V +5V C21 C15 1000uF/16V 104 S12V C19 470uF/25V +12V D8 ZD1 5V6 C7 100uF/50v +5V L3 BEAD C24 470uF/16V 103/1KV 27K/2W 100P R9 4K7
C5V DGND
1 2 3 4 5
VR1 471
*
17
* *
2 7
*
13
CN3 D13 D14 MIC1 MIC2 AGNG +12V -12V DGND DGND +5V D3.6V 1 2 3 4 5 6 7 8 9 10 MIC1 MIC2 AGND +12V -12V DGND DGND +5V +3.6V
D3.6V
*
18
8 7 6 5 R6 0.39R/1W
*
14
D11
16
TEA1523P
!
U2 SFH615AGR
!
C3
-12V CN5 MIC1 MIC2 AGND -12V +12V 1 2 3 4 5 PIN4 D3.6V CN4 R14 3.9K R15 750 +5V AGND AGND +12V -12V AGND AGND +5V +5V D3.6V 1 2 3 4 5 6 7 8 9 10 +5V AGND AGND +12V -12V AGND AGND +5V +5V D3.6V MIC1 MIC2 AGND -12V +12V
C22 330uF/25V
C23 330uF/25V
C6 100uF/50V
C4 474
473
B 3 1 2 C5 474
U3 TL431
R13 10k
NO USE!
BC6 222/250V~
!
A
47
47
LOADER
MPEG BOARD
DQ16 DQ18 TUNER_VCC TUN_L GND TUN_R DQ19 VSTB A20 VSTB GND RDS_MPX RDS_MPX 3V3 5V VCC GND GND 3V3 5V VCC GND GND
FRONT PANEL
F1 F2 -27V GND
48
F1 F2 -27V GND
POWER SUPPLY
DQ16 DQ18 TUNER_VCC TUN_L GND TUN_R DQ19 VSTB A20 VSTB GND RDS_MPX RDS_MPX -12V +12V AGND VGND +5V
RECEIVER
ML MR AGND SL SR AGND CENT LEF AGND MIC/MUTE MUTE AGND ASPDIF +5V