You are on page 1of 82

ORDER NO.

CRT3401
DEH-P4750MP/XM/GS

MULTI-CD CONTROL HIGH POWER CD/MP3/WMA PLAYER WITH FM/AM TUNER

DEH-P4750MP
DEH-P4790MP/XM/ID DEH-P4770MP/XM/CS
Model No.
CX-3158

/XM/GS

This service manual should be used together with the following manual(s):
Order No.
CRT3394

Mech.Module
S10.1AAC

Remarks
CD Mech. Module : Circuit Description, Mech. Description, Disassembly

For details, refer to "Important Check Points for Good Servicing".


PIONEER CORPORATION

4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 2004


K-ZZA. DEC. 2004 Printed in Japan

SAFETY INFORMATION
A

This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.

CAUTION
B

Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacture. Discord used batteries according to the manufacture's instructions.

- Service Precaution
1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual. 2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during power-on mode may damage the ICs inside the unit. 3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment (shorting-solder) by referring to "the DISASSEMBLY". 4. After replacing the pickup unit, be sure to check the grating.

DEH-P4750MP/XM/GS
1 2 3 4

[Important Check Points for Good Servicing]


In this manual, procedures that must be performed during repairs are marked with the below symbol. Please be sure to confirm and follow these procedures.

1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual. 1 Use specified parts for repair. Use genuine parts. Be sure to use important parts for safety. 2 Do not perform modifications without proper instructions. Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise. 3 Make sure the soldering of repaired locations is properly performed. When you solder while repairing, please be sure that there are no cold solder and other debris. Soldering should be finished with the proper quantity. (Refer to the example) 4 Make sure the screws are tightly fastened. Please be sure that all screws are fastened, and that there are no loose screws. 5 Make sure each connectors are correctly inserted. Please be sure that all connectors are inserted, and that there are no imperfect insertion. 6 Make sure the wiring cables are set to their original state. Please replace the wiring and cables to the original state after repairs. In addition, be sure that there are no pinched wires, etc. 7 Make sure screws and soldering scraps do not remain inside the product. Please check that neither solder debris nor screws remain inside the product. 8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord. Damaged power cords may lead to fire accidents, so please be sure that there are no damages. If you find a damaged power cord, please exchange it with a suitable one. 9 There should be no spark traces or similar marks on the power plug. When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary. 0 Safe environment should be secured during servicing. When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely.

2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification. Adjustments should be performed in accordance with the procedures/instructions described in this manual.

3. Lubricants, Glues, and Replacement parts


Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied.
E

4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances.

5. Shipping mode and Shipping screws


To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

DEH-P4750MP/XM/GS
5 6 7 8

CONTENTS
A

SAFETY INFORMATION ..................................................................................................................................... 2 1. SPECIFICATIONS ............................................................................................................................................ 5 2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 8 2.1 PACKING ................................................................................................................................................... 8 2.2 EXTERIOR............................................................................................................................................... 10 2.3 CD MECHANISM MODULE..................................................................................................................... 14 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .......................................................................................... 16 3.1 BLOCK DIAGRAM ................................................................................................................................... 16 3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE).............................................................................. 18 3.3 KEYBOARD UNIT.................................................................................................................................... 24 3.4 CD MECHANISM MODULE(GUIDE PAGE) ............................................................................................ 26 4. PCB CONNECTION DIAGRAM ..................................................................................................................... 36 4.1 TUNER AMP UNIT................................................................................................................................... 36 4.2 KEYBOARD UNIT.................................................................................................................................... 40 4.3 CD CORE UNIT(S10.1) ........................................................................................................................... 42 4.4 PANEL UNIT ............................................................................................................................................ 44 5. ELECTRICAL PARTS LIST ............................................................................................................................ 45 6. ADJUSTMENT ............................................................................................................................................... 50 6.1 CD ADJUSTMENT................................................................................................................................... 50 6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT .................................................... 52 6.3 ERROR MODE ........................................................................................................................................ 54 6.4 SYSTEM MICROCOMPUTER TEST PROGRAM ................................................................................... 55 7. GENERAL INFORMATION ............................................................................................................................. 56 7.1 DIAGNOSIS ............................................................................................................................................. 56 7.1.1 DISASSEMBLY ..................................................................................................................................... 56 7.1.2 CONNECTOR FUNCTION DESCRIPTION .......................................................................................... 59 7.2 PARTS...................................................................................................................................................... 60 7.2.1 IC .......................................................................................................................................................... 60 7.2.2 DISPLAY ............................................................................................................................................... 68 7.3 OPERATIONAL FLOW CHART ............................................................................................................... 69 7.4 CLEANING............................................................................................................................................... 70 8. OPERATIONS ................................................................................................................................................ 71

DEH-P4750MP/XM/GS
1 2 3 4

1. SPECIFICATIONS
A

DEH-P4750MP/XM/GS
5 6 7 8

DEH-P4750MP/XM/GS
1 2 3 4

DEH-P4750MP/XM/GS
5 6 7 8

2. EXPLODED VIEWS AND PARTS LIST


NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
A

The > mark found on some component parts indicatesthe importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screw adjacent to mark on the product are used for disassembly. For the applying amount of lobricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.)

2.1 PACKING

"

DEH-P4750MP/XM/GS
2 3 4

(1) PACKING SECTION PARTS LIST


Mark No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Description Polyethylene Bag Cord Assy Accessory Assy Screw Assy Screw Polyethylene Bag Screw Screw Polyethylene Bag Handle Part No. CEG-162 XDE7008 CEA4850 CEA3849 * Mark No. 14 15 16 17 18 19 20 21 22-1 22-2 22-3 23 Bush Remote Control Unit Battery Carton Contain Box Protector Protector Owner's Manual Installation Manual Caution Card Case Assy Description Part No. CNV3930 CXC3173 CEX1065 See Contrast table(2) See Contrast table(2) XHP7003 XHP7004 See Contrast table(2) See Contrast table(2) CRP1310 CXB3520

CBA1650 CEG-127 CRZ50P090FTC TRZ50P080FTC CEG-158 CNC5395

(2) CONTRAST TABLE DEH-P4750MP/XM/GS, DEH-P4790MP/XM/ID and DEH-P4770MP/XM/CS are constructed the same except for the following:
Mark No.
18 19 22-1 22-2

Description
Carton Contain Box Owner's Manual Installation Manual

DEH-P4750MP/XM/GS
CHG5424 CHL5424 CRD3949 CRD3950

DEH-P4790MP/XM/ID
CHG5428 CHL5428 CRD3949 CRD3950

DEH-P4770MP/XM/CS
CHG5425 CHL5425 CRD3951 CRD3952

Owner's Manual,Installation Manual


Part No.
CRD3949 CRD3950 CRD3951 CRD3952

Language
English, Traditional Chinese, Arabic English, Traditional Chinese, Arabic English, Spanish, Portuguese(B) English, Spanish, Portuguese(B)
D

DEH-P4750MP/XM/GS
5 6 7 8

2.2 EXTERIOR
A

10

DEH-P4750MP/XM/GS
1 2 3 4

(1) EXTERIOR SECTION PARTS LIST


Mark No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 Description Screw Screw Screw Screw Cable Case Earth Plate Insulator Cushion Tuner Amp Unit Screw Screw Screw Fuse(10A) FM/AM Tuner Unit Holder Pin Jack(CN351) Plug(CN981) Connector(CN101) Plug(CN831) Connector(CN721) Antenna Jack(CN401) Holder Heat Sink Terminal(CN402) Holder Insulator Holder Unit Chassis Unit Remote Control Unit Cover Detach Grille Assy Screw Button(SOURCE) Button(BAND) Spring LCD(LCD1) Connector(CN1) Holder Sheet Lighting Conductor Connector Cushion Sub Grille Assy Knob(VOLUME) Button(CLOCK) Button(DISPLAY) Button(LOUDNESS) Part No. BMZ30P040FZK BSZ26P060FTC BSZ30P060FTC BSZ30P200FTC CDE7189 CNB2793 CNC8915 CNM7682 CNM8890 See Contrast table(2) ASZ26P060FTC BPZ26P080FTC BSZ26P160FTC CEK1208 CWE1646 CND1054 See Contrast table(2) CKM1376 CKS3408 CKS3537 CKS3837 CKX1056 CND1352 CNR1668 VNF1084 See Contrast table(2) XNM7031 CXB6681 CXB9528 CXC3173 CNS7068 See Contrast table(2) BPZ20P100FZK CAC9008 CAC9009 CBL1470 See Contrast table(2) CKS5207 CND2510 CNM9287 CNV8274 CNV8275 XNM7049 See Contrast table(2) XAA7021 See Contrast table(2) See Contrast table(2) See Contrast table(2) Mark No. 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 Description Button(OPEN) Button(1-6) Part No. See Contrast table(2)
A

XAC7070 Button(FUNCTION, AUDIO, EQ) XAC7071 Spring XBH7001 Cover XNS7087


Sub Button Assy(UP, DOWN, LEFT, RIGHT) XXA7310

Button(EJECT) Screw(M2x4.5) Screw(M2x4) Washer Spring Spring Spring Spring Holder Gear Arm Arm Arm Arm Panel Unit Socket(CN1950) Connector(CN1951) Holder Unit Holder Unit Damper Unit Sub Panel Unit Cover Lighting Conductor Spring Pin

CAC7752 CBA1647 CBA1649 CBF1038 CBH2650 CBH2651 CBH2652 CBH2653 CND1254 CNV5997 CNV7400 CNV7401 CNV7402 CNV7403 CWM9781 CKS3550 CKS4806 CXB9501 CXB9502 CXB9503 XXA7361 CNM6854 CNV6487 CBL1512 CNV6486

>

CD Mechanism Module(S10.1AACA) CXK5668

Screw Cord Assy Insulator Insulator Panel Sheet Choke Coil(L981) Transistor(Q751, 901) IC(IC911) IC(IC301) Holder Screw IC(IC2)

ISS26P055FTC XDE7008 XNM7100 XNM7106 XNS7088 See Contrast table(2) CTH1291 2SD2396 NJM2388F84 PAL007A CNV7619 BMZ40P140FTC TSOP4840SB1
F

DEH-P4750MP/XM/GS
5 6 7 8

11

(2) CONTRAST TABLE DEH-P4750MP/XM/GS, DEH-P4790MP/XM/ID and DEH-P4770MP/XM/CS are constructed the same except for the following:
Mark
A

No.
10 17 27 33 38 45 47 48 49 50 87

Description
Tuner Amp Unit Pin Jack(CN351) Holder Detach Grille Assy LCD(LCD1) Sub Grille Assy Button(CLOCK) Button(DISPLAY) Button(LOUDNESS) Button(OPEN) Sheet

DEH-P4750MP/XM/GS
CWM9777 CKB1059 CND1237 CXC3891 CAW1852 CXC3948 CAC9004 CAC9005 CAC9006 CAC9007 CNM9288

DEH-P4790MP/XM/ID
CWM9777 CKB1059 CND1237 CXC4374 CAW1852 CXC4332 CAC9004 CAC9005 CAC9006 CAC9007 CNM9288

DEH-P4770MP/XM/CS
CWM9895 CKB1054 CND1238 CXC3893 CAW1851 CXC4330 XAC7062 XAC7063 CAC9086 XAC7065 Not used

12

DEH-P4750MP/XM/GS
1 2 3 4

DEH-P4750MP/XM/GS
5 6 7 8

13

2.3 CD MECHANISM MODULE


5 42
A

13 5 13 34 5 93 13
A B

81 15
E

22
F

92 82 83 68
G

26

44 5
1

13
D

86 86

54 53 37

52

28 4

28 45
J

4 55 5
1 1

71 87 50 72 10

23 38

36 4 18 29 51
1 2

73

23
K

64 47

75 59

I
1

76

24

49
E M
1

61
2

F A Q H

77

90 48

63
2 1

27 8 67 17 78 46 60 80 6
N

21
M

G N R
1 1

57
D

16

79

12
3

58
2

33
P
2

62
1

20
1

40

60 11 89 10

1GEM1024 2GEM1045 3GEM1035


56
E

1 1

39 69 30 14 25
L

43
K

19

70

74
R

41 31 85

91

C
1 3 2

14 65 85 66 85
O

35 31

14

DEH-P4750MP/XM/GS
1 2 3 4

CD MECHANISM MODULE SECTION PARTS LIST


Mark No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 Description CD Core Unit(S10.1) Connector(CN101) Connector(CN901) Screw Screw Screw(M2x4) Screw(M2x3) Screw(M2x3) Washer Washer Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Shaft Frame Frame Bracket Bracket Arm Arm Lever Lever Sheet Collar Guide Arm Rack Holder Holder Arm Part No. CWX3096 CKS4182 CKS4017 BMZ20P035FTC BSZ20P040FTC CBA1362 CBA1824 CBA1825 CBF1038 CBF1060 CBH2390 CBH2606 CBH2607 CBH2608 CBH2609 CBH2610 CBH2735 CBH2612 CBH2613 CBH2614 CBH2615 CBH2616 CBH2617 CBH2620 CBH2621 CBH2641 CBH2642 CBH2643 CBH2659 CBH2688 CLA4441 CNC9962 CNC9963 CND2712 CND1895 CNC9968 CND1909 CND2032 CNC9984 CNM8134 CNV7798 CNV7799 CNV8403 CNV8374 CNV8376 CNV8377 CNV8378 Mark No. 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 Gear Gear Gear Gear Gear Gear Rack Arm Arm Guide Roller Gear Arm Arm Arm Damper Damper Arm Arm Guide Guide Holder Arm Gear Damper Motor Unit(M1) Chassis Unit Screw Unit Gear Unit Arm Unit Arm Arm Motor Unit(M2) Bracket Screw(M2x5) Screw Screw Washer Pickup Unit(P10)(Service) Screw Spring Clamper Description Part No. CNV8379 CNV8380 CNV8381 CNV8382 CNV8383 CNV8384 CNV8385 CNV8386 CNV8387 CNV8388 CNV7218 CNV8389 CNV8391 CNV8390 CNV8392 CNV7313 CNV7314 CNV8394 CNV8395 CNV8396 CNV8397 CNV8398 CNV8402 CNV8400 CNV7618 CXC4440 CXC2318 CXB8729 CXC2397 CXC2316 CND1896 CND1894 CXB8933 CNC9985 EBA1028 JFZ20P020FTC JGZ17P022FTC YE20FTC CXX1641 IMS26P030FTC CBL1635 CNV8372
A

DEH-P4750MP/XM/GS
5 6 7 8

15

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM


3.1 BLOCK DIAGRAM
A

A TUNER AMP UNIT


VDD

7 6
WC CE2

13
ROM_VDD

5
SL

10 9 8
CE1 CK DI

11
NC

14
DO

18 19 20 21
NC NC NC NC

FM/AM TUNER UNIT

5V

OSC

LPF

ANTENNA

CN401
1 2,3
IC 2 2.5V Lch DET, FM MPX AM ANT 1 ATT Rch FMRF

FM ANT ATT FMRF ANT adj RF adj

IC 1 3.3V MIXER, IF AMP

T51

CF52 CF51

AUDIOGND

OSCGND

VDD_3.3

RFGND

DGND

3.3V

IC 4 3.3V 2.5V 2.5V

12

15

22

16

VCC

NC

17

TUN 3.3V SYS +B CDL

PICKUP UNIT (P10)(SERVICE)


LASER DIODE LDMD 15 5

C CD CORE UNIT(S10.1)
V3R3D

CN101
15 5 AC,BD E,F FOP 1 TOP 4 LD+ 14 1 4 14 FOP TOP FD,TD 12 FOP 13 TOP M1 SPINDLE MOTOR SD,MD X701 142 Q101 143 LD PD

IC 201 UPD63763GJ CN901 RF AMP, CD DECODER, LOUT MP3 AND WMA DECODER, DIGITAL SERVO/DATA PROCESSOR
31 LOUT 10 14

HOLOGRAM UNIT FOCUS ACT. MONITOR TRACKING ACT. DIODE

12 X1

13 X2

CD DRIVER
16 SOP 15 SOM 18 LCOP 17 LCOM LOEJ CONT 22 9 53 47

MICRO COMPUTER
LOEJ CONT reset

14

M2 LOADING/CARRIAGE MOTOR

IC 301 BA5835FP
32 31 30 97

IC 701 PE5454A

BRST,BRXEN,BSRQ BDATA,BSCK
VD VD 3 4 21 20

12EJ 8EJ DSCSNS HOME VDCONT VDCONT CD3VON 49 46

S904 12EJ

S905 S901 S903 8EJ DSCSNS HOME VD2 2 22

V3R3D

IC 203 NJM2885DL1-33 3.3V REGULATOR

VD2

3V REGULATOR
3VDD 3

IC 703

S-812C33AUA-C2N
VDD

16

DEH-P4750MP/XM/GS
1 2 3 4

IC 3 EEPROM 5.0V

IC 5 3.3V

24

23

7 IC 431 NJM4558MD

E
TUN L 3

6 5 4

CN101 IP-BUS
11 BUSL7 BUSL+

Q101
8

B.UP

Q102 ASENBO 71 ASENBO

5 1

5 6

BUSBUS+

IC 101 HA12240FP

DIN1 DOUT STBY

1 2 8

86 85 24

TX RX IPPW

SYSTEM CONTR CN721


CD L

IC 601(2/2 PE5465A

RESET

15

RESET

RST2

BRST,BRXEN,BSRQ,BDATA,BSCK Q751 B.UP 3 Q753 5 2 4

VD1

19

5 VDCONT

Q761 VD2

Q762
CD3VON 1 23

CD3VON

VDD

19

VDD

CN351
RESET
A RST2 1

R Lch
3 VDD

REAR OUTPUT

IC 651 BD4834G

Q352

(DEH-P4770MP/XM/CS)
11 RESET

F Lch Q351

FRONT OUTPUT

TUNPDO TUNPDI SL TUNPCK CE1 CE2

98 94 74

TUNPDO TUNPDI 100

SP601
PEE

SL 97 TUNPCK 99 TUNPCE1 32 TUNPCE2

VDD 5V REG
Q901 VDD Q902

SYSTEM CONTROLLER
IC 601(1/2) PE5465A
DALMON 10

7 IC 431 NJM4558MD BSENS ASENS 93 92 BSENS

BACKUP SENSE
Q931 ASENS

B.UP

CN981
16
FUSE 10A

16 14

BACK UP

ACC

14

ACC

ACC SENSE
15 B.UP 15
GND

AMP
TUN L 3

20

ELECTRONIC VOLUME/ SOURCE SELECTOR


IN2L F Lch 10 14 RLIN

VCC3/4 VCC1/2 FLFL+ RLRL+ 22 23 21 3 5 7 5 8 6 11 7 5 8 6 11

R Lch 6 5 CDL 4 IN4-L IN4+L IN3L

11

12

IC 301 PAL007A

FLFL+ RLRL+
B. REM

FLIN

IC 231 PML003AM
MUTE STBY 4

B.REMOTE

25

EVCK, EVDT, EVST

MUTE
Q391 B.UP B.UP

MUTE
Q371 SYS+B

TUN 3V REG.
TU 3.3V Q301 3

SYS 8V REG.
1 2

IC 921 NJM2391DL1-33

IC 911 NJM2388F84
4

B.UP

71

ASENBO

MUTE

86 85 24

TX RX IPPW

SYSPW

21

SYSPW

37

SYSPW

SYSTEM CONTROLLER
IC 601(2/2) PE5465A

X1 X2

16 15 X601 12.58291MHz

D
CN831
Q871 B.UP Q872 20 ILB 10 10

PANEL UNIT
CN1951
ILB S1970 5 8

B
CN1
BL+B S2,S4,S9,S12,S14,S18

KEYBOARD UNIT

CN1950

ILMPW

EJECTIN

8 Q861 B.UP Q862 9 Q851 VDD Q852

EJSW

EJILP

EJECT

FLPILM

SWVDD

SWVDD

KEY MATRIX
2 11 SWVDD SWVDD

SWVDD ROT1 ROT0 CSENS DPDT KYDT DSENS

1 56 57 77 96 95 S831 90

VOLUME
S19 ROT1 ROT0 12 13 12 13 6 11 14 ROT1 ROT0 CSENS DPDT KYDT 7 9 11 10 8 6 4 2 3 5 DPDT KYDT ROT1 ROT0 3

REM.CON. IC2 TSOP4840SB1


2

17 REM 18 KEY DATA XO XI 22 23 X1 4.97MHz

CSENS 6 DPDT KYDT 11 14

DPDT

20 KYDT 10 VLCD 55 VDD

LCD DRIVER/ KEY CONTROLLER


IC 1 PD6340A

F
LCD1

DSENS

DEH-P4750MP/XM/GS
5 6 7 8

17

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)


A

Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST".
A-a A-b

Large size SCH diagram

A-a

A-a

A-b

Guide page

A-a

A-b

Detailed page

C
CN901
CD-DA, MP3 : 0.2dB

FM(30%) : -31dB AM(30%) : -31dB IP-BUS : 2.2dB CD-DA, MP3 : 0.2dB

C
8 9 10 11 5 6 7 1 2 3 4

IP-BUS : 2.2dB

mute

D
FM/AM TUNER UNIT

NC NC NC NC

TSCK/BSCK

FM(30%) : -30dB AM(30%) : -30dB

NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. Decimal points for resistor and capacitor fixed values are expressed as : 2.2 2R2 0.022 R022

EJECT

CN1

DSENS

PANEL UNIT

A D
18 DEH-P4750MP/XM/GS
1 2 3 4

ASENSBO

TSI/BSI

NC

NC

NC

dalmon

A-b
A
TUNER AMP UNIT

FRONT R CH FRONT L CH

B
REAR R CH REAR L CH

>

FM(30%) : -6.66dB AM(30%) : -6.66dB IP-BUS : 9.54dB CD-DA, MP3 : 9.54dB

FM(30%) : -5.9dB AM(30%) : -5.9dB IP-BUS : 10.3dB CD-DA, MP3 : 10.3dB

C
POWER AMP

dalmon

BEEP

NC NC

D
600H

>
TSCK/BSCK ASENSBO TSI/BSI

BACKUP GND ACC

B.REM

RL FL RL+ FL+ RR FR RR+ FR+

FM(30%) : 20.1dB AM(30%) : 20.1dB IP-BUS : 36.3dB CD-DA, MP3 : 36.3dB

The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.

A
DEH-P4750MP/XM/GS
5 6 7 8

19

CD-DA, MP3 : 0.2dB

8 9 10 11

5 6 7 1 2 3 4

IP-BUS : 2.2dB

mute

dalmon

20

A-b

A-a
A-a A-b

1
FM(30%) : -31dB AM(30%) : -31dB IP-BUS : 2.2dB CD-DA, MP3 : 0.2dB

CN901

DEH-P4750MP/XM/GS

mute

dalmon

NC

NC

NC

TSCK/BSCK

TSI/BSI

FM/AM TUNER UNIT

ASENSBO

FM(30%) : -30dB AM(30%) : -30dB

5
NC NC NC NC

6
EJECT

DEH-P4750MP/XM/GS

3 4

NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors.

CN1

DSENS

A-a D
E

Decimal points for resistor and capacitor fixed values are expressed as : 2.2 2R2 0.022 R022
A-a A-b

PANEL UNIT

A-b

21

dalmon

22
A-a A-b

A-b

A
TUNER AMP UNIT

1
FRONT R CH FRONT L CH REAR R CH REAR L CH

2
> POWER AMP

DEH-P4750MP/XM/GS

FM(30%) : -6.66dB AM(30%) : -6.66dB IP-BUS : 9.54dB CD-DA, MP3 : 9.54dB

FM(30%) : -5.9dB AM(30%) : -5.9dB IP-BUS : 10.3dB CD-DA, MP3 : 10.3dB

1
4

BEEP

dalmon

BEEP

ASENSBO

NC

NC

600H

>

BACKUP GND ACC

B.REM

RL FL RL+ FL+ RR FR RR+ FR+

FM(30%) : 20.1dB AM(30%) : 20.1dB IP-BUS : 36.3dB CD-DA, MP3 : 36.3dB

2
7

DEH-P4750MP/XM/GS
A-a A-b

3
The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
8 E A D C B

A-b

23

3.3 KEYBOARD UNIT


A

LCD DRIVER/ KEY CONTROLLER

B
24 DEH-P4750MP/XM/GS
1 2 3 4

GS,ID:CAW1852 CS:CAW1851

KEYBOARD UNIT

DISPLAY

CN1951

D
C
FUNCTION CLOCK LOUDNESS

GS,ID:NSCW505C-4237 CS:NSCW505C-4234

VOLUME

: The power supply is shown with the marked box.

B
DEH-P4750MP/XM/GS
5 6 7 8

25

3.4 CD MECHANISM MODULE(GUIDE PAGE)


A

C-a
C S T F

PICKUP UNIT(P10)(SERVICE)
%

F F F T T

T F T T F F T

# @

3
$

2
T

1
F

9
C

7 8

E
M1 CXC4440 SPINDLE MOTOR
S S

TY

F F T T

C C

M2 CXB8933 LOADING /CARRIAGE MOTOR

CD DRIVER

C
26 DEH-P4750MP/XM/GS
1 2 3 4

C-b

ras

SWITCHES: CD CORE UNIT(S10.1) S901:HOME SWITCH..........ON-OFF S903:DSCSNS SWITCH......ON-OFF S904:12EJ SWITCH.............ON-OFF S905:8EJ SWITCH...............ON-OFF The underlined indicates the switch position.

SIGNAL LINE
F T C
!

FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE

CD CORE UNIT(S10.1)

3.3V REGULATOR

SRAMLEVEL2

MICRO COMPUTER

SRAMLEVEL1 SRAMLEVEL0

3V REGULATOR

A
CN721

E
TYPE_A/D

&

C
DEH-P4750MP/XM/GS
5 6 7 8

27

PICKUP UNIT(P10)(SERVICE)
%

28

C-b

C-a
C-a C-b A-a

2
F F F T T T F T T F F T

DEH-P4750MP/XM/GS
# @

2
5

3
$
T S

6
9
C F

2
7 8 0 5

1
4

M1 CXC4440 SPINDLE MOTOR

S F F T T

DEH-P4750MP/XM/GS
CD DRIVER
C-a C-b A-a

7 E D

M2 CXB8933 LOADING /CARRIAGE MOTOR

6
8

C-b

C-a

29

30
C-a C-b

C-b
SWITCHES: CD CORE UNIT(S10.1) S901:HOME SWITCH..........ON-OFF S903:DSCSNS SWITCH......ON-OFF S904:12EJ SWITCH.............ON-OFF S905:8EJ SWITCH...............ON-OFF The underlined indicates the switch position.

1
SIGNAL LINE
F

1
2
FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE
T C
!

ras

2
S

DEH-P4750MP/XM/GS

C CD CORE UNIT(S10.1)
3

3.3V REGULATOR

2
5
SRAMLEVEL2

5
SRAMLEVEL1 SRAMLEVEL0

3
3V REGULATOR
^ &
C-a C-b

MICRO COMPUTER
6

A
CN721

TYPE_A/D

4
7 8 E A D C B

DEH-P4750MP/XM/GS

C-b

31

- Waveforms
A

Note : 1. The encircled numbers denote measuring points in the circuit diagram. 2. Reference voltage REFO1(1.65V) 500ms/div 1 DSCSNS 5 CLCONT 4 LOEJ 6 VD 5V/div 5V/div 5V/div 10V/div 500ms/div 1 DSCSNS 2 8SNS 3 12SNS 4 LOEJ 5V/div 5V/div 5V/div 5V/div 500ms/div

1 DSCSNS 2 8SNS 3 12SNS 4 LOEJ

5V/div 5V/div 5V/div 5V/div

12 cm CD Loading operation

12 cm CD Loading operation

8 cm CD Loading operation

Ref.: GND Mode: Normal

Ref.: GND Mode: Normal

Ref.: GND Mode: Normal

7 SIN 8 CIN 9 TIN

1V/div 2s/div 500mV/div 500mV/div

7 SIN 8 CIN 9 TIN

1V/div 1s/div 500mV/div 500mV/div

7 SIN 8 CIN 9 TIN

1V/div 2s/div 500mV/div 500mV/div

12 cm CD-DA setup operation after loading

12 cm CD-ROM(1 session) setup operation after loading

12 cm CD-ROM(3 sessions) setup operation after loading

Ref.: REFO Mode: Normal

Ref.: REFO Mode: Normal

Ref.: REFO Mode: Normal

0 FIN ! RFOK 7 SIN

200mV/div 500ms/div @ TE 2V/div # FE 2V/div

500mV/div 200ms/div # FE 500mV/div 0 FIN @ TE 9 TIN

500mV/div 20ms/div 500mV/div 500mV/div 500mV/div

12 cm CD-DA Source On setup operation

Source On setup operation

CD-DA Play operation

Ref.: REFO Mode: Normal

Ref.: REFO Mode: Normal

Ref.: REFO Mode: Normal

# FE 0 FIN @ TE 9 TIN

500mV/div 20ms/div 500mV/div 500mV/div 500mV/div

$ MDX 7 SIN

1V/div 50ms/div 200mV/div

$ MDX 7 SIN

2V/div 1V/div

5s/div

CD-ROM play operation(Regular track Jump)

Spindle waveform during play operation

Spindle waveform during play operation (Wider)

Ref.: REFO Mode: Normal

Ref.: REFO Mode: Normal

Ref.: REFO Mode: Normal

32

DEH-P4750MP/XM/GS
1 2 3 4

0 FIN # FE

500mV/div 200ms/div @ TE 500mV/div % RFAGC

500mV/div 2ms/div 500mV/div

% RFAGC @ TE 9 TIN

1V/div 500s/div 500mV/div 500mV/div

Focus Search waveform

Track Open waveform

1 Track Jump waveform

Ref.: REFO Mode: TEST

Ref.: REFO Mode: TEST

Ref.: REFO Mode: TEST

% RFAGC @ TE 9 TIN

1V/div 500s/div % RFAGC 500mV/div @ TE 500mV/div 9 TIN

1V/div 1ms/div 500mV/div 500mV/div

% RFAGC @ TE 9 TIN

1V/div 2ms/div 500mV/div 500mV/div

4 Tracks Jump waveform

10 Tracks Jump waveform

32 Tracks Jump waveform

Ref.: REFO Mode: TEST

Ref.: REFO Mode: TEST

Ref.: REFO

C
Mode: TEST

% RFAGC @ TE 8 CIN 7 SIN

200ms/div ^ LOUT 1V/div 1V/div & ROUT 500mV/div 2V/div

1V/div 1V/div

200s/div 1 DSCSNS 2 8SNS 3 12SNS 4 LOEJ

5V/div 5V/div 5V/div 5V/div

500ms/div

Search operation(Outter to Inner)

Analog audio waveform

12 cm CD Eject operation

D
Ref.: REFO Mode: Normal Ref.: AGND Mode: Normal Ref.: GND Mode: Normal

1 DSCSNS 5V/div 5 CLCONT 5V/div 4 LOEJ 5V/div


12 cm CD Eject operation

500ms/div 1 DSCSNS 2 8SNS 3 12SNS 4 LOEJ

5V/div 5V/div 5V/div 5V/div

500ms/div 7 SIN 8 CIN 9 TIN

1V/div 500ms/div 500mV/div 500mV/div


E

8 cm CD Eject operation

CD-DA >> CD-ROM mode change(Band key)

Ref.: GND Mode: Normal

Ref.: GND Mode: Normal

Ref.: REFO Mode: Normal

DEH-P4750MP/XM/GS
5 6 7 8

33

7 SIN 8 CIN 9 TIN

1V/div 500ms/div % RFAGC 500mV/div 9 TIN 500mV/div @ TE 0 FIN

1V/div 1V/div 1V/div 1V/div

500s/div

CD-ROM >> CD-DA mode change(Band key)

Black dot(800m) during play

Ref.: REFO Mode: Normal

Ref.: REFO Mode: Normal

34

DEH-P4750MP/XM/GS
1 2 3 4

DEH-P4750MP/XM/GS
5 6 7 8

35

4. PCB CONNECTION DIAGRAM


4.1 TUNER AMP UNIT
A

NOTE FOR PCB DIAGRAMS


1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic diagram. 2.Viewpoint of PCB diagrams

TUNER AMP UNIT


150

CORD ASSY
140
1

Connector

Capacitor
2

IP-BUS
4 3 7 2 6 8 1 5

16 15

14 13

12 11

10 9

8 7

6 5

4 3

SIDE A
B
P.C.Board Chip Part

130
3

SIDE B
120

11 10 9

110

100

C
90

80

70

D
60

50

40

C
CN901
30

20

10

Y
F
0

DSENS

A
36
1 2

10

20

30

40

50

60

X DEH-P4750MP/XM/GS
3 4

SIDE A
(DEH-P4770MP/XM/CS)

ORD ASSY

FRONT OUTPUT

REAR OUTPUT

12 11

10 9

8 7

6 5

4 3

2 1

ANTENNA
2

FM/AM TUNER UNIT

CN1950

FRONT
60 70 80 90 100 110 120 130 140 150 160 170

A
37

DEH-P4750MP/XM/GS
5 6 7 8

TUNER AMP UNIT

D
TST

PCL

A
38
1

170

160

150

140

130

120

110

100

90

80

DEH-P4750MP/XM/GS
2 3 4

SIDE B
150

140
1

130

B
120

110

100

C
90

80

70

D
60

50

40

E
30

20

10

Y
F
0 90 80 70 60 50 40 30 20 10 0

X DEH-P4750MP/XM/GS
5 6 7 8

A
39

40

B
B
KEYBOARD UNIT
FUNCTION LEFT UP RIGHT AUDIO DOWN EQ SOURCE 1 2 3 4 5 6 BAND LOUDNESS

4.2 KEYBOARD UNIT

40
2

CLOCK

30

VOLUME

DEH-P4750MP/XM/GS
30 40 50 70 60 80 90 100 110

20

10

DISPLAY

10

20

120

130

140

150

160

SIDE A

KEYBOARD UNIT

SIDE B
A

160 150 140

D
130

CN1951

120 110 100


C

90 80 70
D

60 50 40
E

30 20 10

X
F

B
8

30

10

20

40

DEH-P4750MP/XM/GS
5 6 7

41

4.3 CD CORE UNIT(S10.1)

C
A

CD CORE UNIT(S10.1)

SIDE A

M2 LOADING /CARRIAGE MOTOR M1 SPINDLE MOTOR

A
CN721

PICKUP UNIT(P10)(SERVICE)

HOME

FE REFO1

C
42 DEH-P4750MP/XM/GS
1 2 3 4

CD CORE UNIT(S10.1)

SIDE B
A

8EJ

12EJ

DSCSNS
B

C
DEH-P4750MP/XM/GS
5 6 7 8

43

4.4 PANEL UNIT


A

D
B

PANEL UNIT

SIDE A

PANEL UNIT

SIDE B

B
EJECT

CN1

CN831

D
44 DEH-P4750MP/XM/GS
1 2 3 4

5. ELECTRICAL PARTS LIST


NOTE: Parts whose parts numbers are omitted are subject to being not supplied. The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... The > mark found on some component parts indicatesthe importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
Circuit Symbol and No. Part No.
D D D D
A

Circuit Symbol and No.


902 921 931 932 (A,30,71) Diode (A,142,21) Diode (A,51,111) Diode (A,58,109) Diode (A,119,125) Diode (A,122,118) Diode (A,66,110) Diode (A,69,108) Diode (B,156,110) Surge Protector (A,75,62) Inductor (A,58,83) Inductor (A,152,93) Ferri-Inductor (A,148,85) Inductor (A,148,63) Inductor (A,98,64) Inductor (A,48,51) Inductor (A,68,26) Inductor

Part No.
MPG06G-6415G50 MPG06G-6415G50 HZU7L(C3) HZU7L(A1) MPG06G-6415G50 MPG06G-6415G50 MPG06G-6415G50 MPG06G-6415G50 RCCA-201Q31UA-PI LAU2R2K LAU2R2K LAU4R7K LAU1R0K LAU1R0K

A Number:CWM9777(GS,ID) Unit
Unit Number:CWM9895(CS) Unit Name:Tuner Amp Unit
MISCELLANEOUS
IC 101 IC 231 IC 301 IC 431 IC 601 IC 651 IC 911 IC 921 Q 101 Q 102 Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q D D D D D D D 301 351 352 371 391 751 753 761 762 851 852 861 862 871 872 901 902 931 391 392 441 751 801 802 803 (A,55,60) IC (B,83,83) IC (A,101,136) IC (A,144,39) IC (A,94,42) IC (A,51,70) IC (A,3,117) IC (B,156,24) IC (A,42,81) Transistor (A,44,79) Transistor (A,126,118) (A,138,125) (A,154,123) (B,134,112) (A,116,107) Transistor Transistor (CS) Transistor Transistor Transistor HA12240FP PML003AM PAL007A NJM4558MD PE5465A BD4834G NJM2388F84 NJM2391DL1-33 2SA1576 DTC124EU DTC124EU UMH3N UMH3N UMD2N 2SC4081 2SD2396 UMD2N 2SA1577 DTC114EU 2SA1576 DTC114EU 2SA1576 DTC114EU 2SB1238 DTC114EU 2SD2396 UMD2N UMX1N HZS7L(B2) DAN202U UDZS5R6(B) HZS9L(A1) UMZ6R8EN UMZ6R8EN UDZS10(B) HZS6L(B1)

D 971 D 972 D 981 D 982 ZNR401 L L L L L L L L L X 101 211 401 402 403 601 701 851 981 601

LAU2R2K LAU2R2K LAU2R2K (A,29,104) Choke Coil 600H CTH1291 (A,97,57) Radiator 12.58291MHz CSS1402

S 831 >FU351 SP601 Y 401 >

(A,22,6) Switch(DSENS) (B,125,131) Fuse 3A (A,132,22) Buzzer

CSN1039 CEK1286 CPV1062 (A,159,98) FM/AM Tuner Unit CWE1646 Fuse 10A CEK1208

(A,3,66) Transistor (B,24,51) Transistor (B,25,29) Transistor (B,20,29) Transistor (B,62,31) Transistor (B,60,27) Transistor (A,42,12) Transistor (A,39,12) Transistor (A,37,18) Transistor (A,34,9) Transistor (A,3,101) Transistor (B,28,65) Transistor (A,57,113) Transistor (A,14,83) Diode (A,124,112) Diode (A,152,37) Diode (A,13,62) Diode (B,117,26) Diode (B,105,26) Diode (B,63,23) Diode (A,27,75) Diode

RESISTORS
R R R R R R R R R R R R R R R R R R R R 101 102 103 104 105 106 107 108 109 110 111 113 114 211 271 272 273 274 277 278 (B,34,130) (B,34,132) (B,34,120) (B,34,134) (B,24,131) (B,28,118) (B,22,131) (B,26,118) (B,23,119) (B,25,118) (B,32,118) (A,39,80) (A,40,77) (A,101,72) (A,107,92) (A,103,92) (A,109,92) (A,105,92) (A,110,96) (A,114,96) RS1/16S150J RS1/16S470J RS1/16S101J RS1/16S101J RS1/16S181J RS1/16S181J RS1/16S223J RS1/16S223J RS1/16S102J RS1/16S102J RS1/16S222J RS1/16S332J RS1/16S562J RAB4C102J RS1/16S101J RS1/16S101J RS1/16S101J RS1/16S101J RS1/16S0R0J RS1/16S0R0J
E

D 901

DEH-P4750MP/XM/GS
5 6 7 8

45

Circuit Symbol and No.


R R R R R R R R R R R R R R R R R R R R R R R R R
C

Part No.
RS1/16S153J RS1/16S103J RS1/16S103J RS1/16S331J RSK1/16S471J RSK1/16S471J RSK1/16S471J RSK1/16S471J RS1/16S821J RS1/16S821J RS1/16S821J RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S102J RS1/16S0R0J RS1/16S104J RS1/16S104J RS1/16S222J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S0R0J RS1/16S103J RS1/16S103J RS1/16S103J RS1/16S103J RS1/16S103J RS1/16S103J RS1/16S103J RS1/16S103J RS1/16S681J RS1/16S102J RS1/16S104J RS1/16S102J RS1/16S473J RS1/16S104J RS1/16S104J RS1/16S473J RS1/16S104J RS1/16S104J RS1/16S104J RS1/16S104J RS1/16S472J RS1/16S102J RS1/16S104J RS1/16S104J RS1/16S104J RS1/16S104J RS1/16S104J RS1/16S104J RS1/16S681J RS1/16S681J RS1/16S681J RAB4C471J RS1/16S0R0J R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

Circuit Symbol and No.


651 652 701 702 703 704 705 706 707 708 712 731 732 733 734 751 761 762 801 802 803 804 805 835 836 838 839 851 852 853 861 862 863 871 872 873 901 902 911 912 931 932 933 934 935 (A,57,68) (A,56,70) (A,58,41) (A,58,31) (A,58,33) (A,58,44) (A,58,42) (A,58,34) (A,41,42) (A,58,38) (B,46,47) (A,64,49) (A,55,51) (A,65,53) (A,58,53) (A,13,54) (B,27,33) (B,23,27) (A,124,24) (A,122,24) (A,75,24) (A,73,24) (A,71,24) (A,103,26) (A,97,23) (A,101,26) (A,97,25) (B,59,30) (B,57,28) (B,57,23) (A,46,12) (A,42,9) (A,39,9) (A,33,15) (A,33,13) (A,33,12) (B,9,74) (B,11,72) (B,3,107) (A,13,94) (A,54,112) (A,53,112) (A,61,112) (A,61,109) (A,59,112) (A,65,101)

Part No.
RS1/16S183J RS1/16S102J RS1/16S221J RS1/16S221J RS1/16S102J RS1/16S102J RS1/16S221J RS1/16S221J RS1/16S221J RAB4C682J RS1/16S473J RS1/16S6800D RS1/16S6800D RS1/16S4700D RS1/16S4700D RD1/4PU102J RS1/16S103J RS1/16S152J RS1/16S222J RS1/16S222J RS1/16S222J RS1/16S222J RS1/16S222J RS1/16S222J RS1/16S104J RS1/16S222J RS1/16S104J RS1/16S473J RS1/16S472J RS1/16S222J RD1/4PU391J RS1/16S473J RS1/16S103J RS1/16S223J RS1/16S182J RS1/16S182J RS1/16S333J RS1/16S103J RS1/16S103J RS1/16S102J RS1/16S104J RS1/16S473J RS1/16S103J RS1/16S473J RS1/16S472J RD1/4PU102J

301 302 303 304 331 332 333 334 351 353 354 355 356 357 368 371 372 391 392 393 401 402 403 404 405 407 408 431 432 433 434 435 436 437 438 441 601 603 605 606 607 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 640

(B,115,122) (A,126,129) (A,126,131) (A,124,131) (A,104,107) (A,99,107) (A,106,107) (A,101,107) (B,128,124) (CS) (B,139,120) (B,155,124) (B,126,126) (CS) (B,137,125) (CS) (B,141,120) (B,153,123) (B,140,105) (A,128,112) (A,119,107) (A,115,105) (A,127,126) (B,155,60) (B,154,78) (B,154,80) (B,154,82) (B,154,84) (B,154,87) (B,156,65) (B,150,39) (B,150,37) (A,150,40) (A,150,39) (B,151,43) (B,149,41) (B,143,44) (A,140,40) (A,152,41) (B,131,34) (B,95,50) (B,100,53) (B,88,50) (A,69,57) (A,80,29) (A,80,31) (A,78,36) (A,101,29) (A,103,29) (A,105,31) (CS) (B,112,41) (A,113,39) (A,110,42) (A,112,42) (B,105,40) (B,116,41) (B,119,41) (B,121,41) (A,108,46) (A,108,47) (A,108,49) (A,93,30) (A,107,30)

R R R R R R R R R R
D

R R R R R R R R R R

R R R R R R R R R R R R R R R

R 981

CAPACITORS
C C C C C C C C C C 101 103 104 105 106 107 108 201 202 203 (B,26,134) (A,56,65) (A,58,65) (B,35,123) (B,28,134) (A,48,60) (B,42,61) (B,118,76) (B,118,71) (A,63,76) (A,64,88) CKSRYB104K25 CKSRYB102K50 CKSRYB102K50 CCSRCH101J50 CCSRCH101J50 CKSRYB472K50 CCSRCH680J50 CKSRYB105K10 CKSRYB105K10 CEJQ1R0M50 CEJQ1R0M50

C 204

46

DEH-P4750MP/XM/GS
1 2 3 4

Circuit Symbol and No.


C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 205 206 207 208 211 212 213 231 232 233 234 301 302 303 304 305 306 331 332 333 334 335 336 337 338 351 352 353 354 361 401 402 403 404 405 407 431 432 433 434 435 436 437 438 441 442 602 603 604 605 606 607 609 611 651 712 731 732 733 (A,70,82) (A,70,88) (A,70,76) (A,69,93) (A,64,82) (B,69,85) (A,100,86) (B,95,83) (B,74,78) (B,98,77) (B,70,79) (A,45,121) 3300F/16V (B,102,141) (A,115,118) (A,110,127) (A,114,112) (A,106,127) (A,106,99) (A,100,99) (A,108,99) (A,102,99) (A,105,103) (A,99,103) (A,108,103) (A,102,103) (A,131,123) (CS) (A,131,116) (CS) (A,138,116) (A,141,110) (B,158,135) (B,162,56) (A,150,56) (B,162,60) (B,162,93) (A,145,95) (B,156,56) (B,153,39) (B,153,37) (A,150,42) (A,150,37) (B,154,43) (B,153,41) (B,143,42) (A,139,40) (A,141,43) (A,150,36) (B,89,64) (A,87,61) (B,98,55) (B,95,55) (B,88,52) (A,79,42) (A,112,54) (B,82,48) (A,61,68) (B,35,27) (A,64,51) (A,59,51) (A,64,55) (A,59,55)
5

Part No.
CEJQ2R2M50 CEJQ2R2M50 CEJQ2R2M50 CEJQ2R2M50 CEJQ470M10 CKSRYB104K25 CEJQ100M16 CKSRYB105K10 CKSRYB105K10 CKSRYB153K50 CKSRYB153K50 CCH1486 CKSQYB105K16 CEHAR100M16 CKSQYB225K10 CEHAR330M10 CKSQYB225K10 CKSRYB474K10 CKSRYB474K10 CKSRYB474K10 CKSRYB474K10 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CEJQ100M16 CEJQ100M16 CEJQ100M16 CEJQ100M16 CKSRYB104K25 CKSRYB103K50 CEJQ470M6R3 CKSRYB103K50 CKSRYB103K50 CEJQ101M16 CKSYB475K10 CKSRYB474K10 CKSRYB474K10 CCSRCH470J50 CCSRCH470J50 CKSRYB474K10 CKSRYB474K10 CCSRCH470J50 CCSRCH470J50 CKSRYB105K10 CKSRYB105K10 CKSRYB105K10 CEJQ4R7M35 CCSRCH200J50 CCSRCH200J50 CKSRYB105K10 CKSRYB104K25 CCSRCH470J50 CCSRCH680J50 CKSRYB105K10 CCSRCH101J50 CCSQCH222J50 CCSQCH222J50 CCSQCH102J50 CCSQCH102J50
6

Circuit Symbol and No.


C C C C C C C C C C C C C C C C C C C 751 752 753 761 762 801 802 803 804 805 901 902 903 904 911 912 913 921 922 (B,18,60) (B,12,50) (A,12,48) (B,26,38) (A,26,41) (B,84,18) (B,86,18) (B,88,18) (B,91,18) (B,111,28) (A,13,67) (B,18,65) (B,31,78) (A,22,66) 470F/16V (A,14,76) (B,7,112) (A,12,114) (A,147,29) (B,152,29) (B,149,17) (A,59,109) (B,55,118)

Part No.
CKSRYB224K10 CKSRYB102K50 CEJQ101M16 CKSRYB473K50 CEAT471M16 CCSRCH220J50 CCSRCH220J50 CCSRCH220J50 CCSRCH220J50 CCSRCH220J50 CEJQ470M10 CKSRYB103K50 CKSRYB472K50 CCH1331
B

CEJQ221M10 CKSRYB103K50 CEJQ101M16 CEJQ220M10 CKSRYB103K50 CKSYB475K10 CKSRYB104K25 CKSRYB104K25

C 923 C 931 C 981

B Number: Unit
Unit Name:Keyboard Unit
MISCELLANEOUS
IC 1 IC 2 D 1 D 2 D 3 D D D D D D D D D D 4 5 6 7 9 10 11 12 13 14 (B,83,19) IC (A,19,35) IC (B,111,24) Diode (B,111,28) Diode (A,131,3) LED (A,32,3) LED (A,132,30) LED (A,8,37) LED (A,132,15) LED (A,13,2) LED (A,150,2) LED (A,130,22) LED (A,13,34) LED (A,2,25) LED (A,155,37) LED PD6340A TSOP4840SB1 DAN202U DAP202U SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT

D 16 D 17 D 20 D X S S S S S S S S 21 1 1 2 3 4 5 6 7 8

(A,122,20) White LED (GS,ID) NSCW505C-4237

(A,122,20) White LED (CS) (A,30,20) White LED (A,30,20) White LED (CS) (A,25,16) LED (A,13,8) LED (A,150,13) Switch (A,126,3) Switch (A,89,3) Switch (A,37,3) Switch (A,150,30) Switch (A,132,26) Switch (A,98,3) Switch (A,50,3) Switch (A,158,21) Switch
7

NSCW505C-4234 NSCW505C-4237 NSCW505C-4234 SML-310PT SML-310PT CSG1107 CSG1174 CSG1174 CSG1174 CSG1107 CSG1173 CSG1174 CSG1174 CSG1107
8

(B,69,18) Ceramic Resonator 4.97MHz CSS1573

C 734

S 9

DEH-P4750MP/XM/GS

47

Circuit Symbol and No.


S S S S S S S S S 10 11 12 13 14 15 16 17 18 (A,132,11) Switch (A,7,34) Switch (A,113,3) Switch (A,65,3) Switch (A,141,21) Switch (A,13,5) Switch (A,130,18) Switch (A,150,5) Switch (A,74,3) Switch

Part No.
CSG1173 CSG1173 CSG1174 CSG1174 CSG1107 CSG1173 CSG1173 CSG1173 CSG1174

Circuit Symbol and No.

Part No.

Unit Name:Panel Unit


MISCELLANEOUS
D 1970 S 1970 (A,26,5) LED CL220PGC
(A,5,78) Push Switch(EJECT) CSG1174

RESISTORS
R 1970 R 1971 (B,35,18) (B,35,16) RS1/16S101J RS1/16S101J

S 19 LCD1

(A,13,21) Encoder(VOLUME) XSD7001

(A,76,22) LCD (GS,ID) (A,76,22) LCD (CS)

CAW1852 CAW1851

CAPACITORS
C 1970 (B,39,64) CKSRYB104K16

RESISTORS
R R R R R R R R R R 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 23 25 26 27 28 29 30 31 32 33 34 35 36 38 39 40 41 42 43 (B,37,29) (B,34,29) (B,32,11) (B,30,11) (B,120,6) (B,152,11) (B,84,6) (B,82,6) (B,119,6) (B,151,11) (B,57,4) (B,59,4) (B,152,30) (B,133,36) (B,154,30) (B,132,36) (B,13,35) (B,12,35) (B,123,35) (B,125,35) (B,33,11) (B,133,9) (B,15,35) (B,149,31) (B,122,8) (B,31,31) (B,98,5) (B,141,34) (B,76,4) (B,143,34) (B,14,7) (B,9,7) (B,131,9) (B,129,9) (B,140,34) (B,15,7) RS1/16S121J RS1/16S2R2J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S222J RS1/16S222J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S151J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S151J RS1/16S151J RS1/16S104J RS1/16S103J

C Number:CWX3096 Unit
Unit Name:CD Core Unit(S10.1)
MISCELLANEOUS
IC 201 IC 203 IC 301 IC 701 IC 703 Q Q L L L L X X S S 101 701 203 207 209 703 201 701 901 903 (A,39,24) (B,45,78) (A,49,88) (A,48,51) (A,30,44) (A,20,22) (B,62,59) (A,53,32) (A,53,31) (A,26,20) IC IC IC IC IC Transistor Transistor Inductor Inductor Inductor UPD63763GJ NJM2885DL1-33 BA5835FP PE5454A S-812C33AUA-C2N 2SA1577 UN2111 CTF1389 CTF1389 CTF1389 CTF1389

R R R R R R R R R R

(A,64,49) Inductor

(A,51,35) Ceramic Resonator 16.934MHz CSS1603 (A,59,53) Ceramic Resonator 4.00MHz CSS1652

R R R R R R R R R R R R R R R

(A,15,43) Switch(HOME) CSN1067 (B,53,100) Switch(DSCSNS) CSN1068 (B,35,108) Switch(12EJ) (B,48,109) Switch(8EJ) CSN1067 CSN1067

S 904 S 905

RESISTORS
R R R R R R R R R R R R R R R R R R R R 101 102 103 201 202 221 222 225 226 227 228 229 232 241 243 245 301 302 304 305 (A,22,24) (A,22,26) (A,25,25) (A,53,16) (A,55,21) (B,31,18) (B,26,18) (A,27,8) (A,27,7) (B,33,10) (B,36,8) (B,34,8) (B,35,10) (B,42,28) (B,44,28) (A,39,38) (A,48,78) (A,42,78) (A,50,78) (A,42,77) RS1/10SR2R4J RS1/10SR2R4J RS1/10SR2R7J RS1/16SS102J RS1/16SS333J RS1/16SS103J RS1/16SS103J RS1/16SS103J RS1/16SS393J RS1/16SS562J RS1/16SS122J RS1/16SS472J RS1/16SS122J RS1/16SS333J RS1/16SS333J RS1/16SS333J RS1/16SS183J RS1/16SS822J RS1/16SS183J RS1/16SS822J

R 44

CAPACITORS
C C C C
F

1 2 4 5

(B,27,31) (B,64,15) (A,132,33) (A,26,13)

CKSQYB475K6R3 CKSRYB224K10 CKSRYF104Z25 CKSRYF104Z25

D Number:CWM9781 Unit
48
1 2

DEH-P4750MP/XM/GS
3 4

Circuit Symbol and No.


R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 307 308 309 310 601 602 606 607 608 705 706 707 708 710 711 714 716 719 720 724 725 726 727 729 730 731 737 740 742 746 750 754 755 765 769 773 777 778 779 901 905 906 908 910 911 (A,36,85) (A,32,83) (A,38,89) (A,35,88) (B,43,59) (B,41,62) (B,44,67) (B,43,56) (B,36,67) (B,50,59) (B,57,61) (A,62,47) (B,50,57) (A,28,77) (B,44,53) (B,51,53) (A,63,56) (B,49,45) (B,46,52) (A,62,42) (B,57,43) (A,52,41) (B,50,54) (A,57,40) (A,65,41) (A,53,41) (A,41,42) (A,35,46) (A,50,41) (B,60,56) (A,39,59) (B,48,60) (A,43,61) (B,51,40) (B,48,40) (B,39,37) (B,48,51) (B,48,52) (B,45,54) (B,52,65) (B,54,60) (B,56,68) (B,45,69) (B,44,69) (B,40,73)

Part No.
RS1/16SS183J RS1/16SS183J RS1/16SS183J RS1/16SS183J RS1/16S101J RS1/16S101J RS1/16S0R0J RS1/16SS0R0J RS1/16SS0R0J RS1/16SS221J RS1/16SS221J RS1/16SS473J RS1/16SS221J RS1/16SS102J RS1/16SS221J RS1/16SS473J RS1/16SS472J RS1/16SS221J RS1/16SS471J RS1/16S473J RS1/16SS222J RS1/16SS103J RS1/16SS473J RS1/16SS223J RS1/16SS473J RS1/16SS104J RS1/16SS104J RS1/16SS473J RS1/16SS104J RS1/16SS104J RS1/16SS473J RS1/16SS102J RS1/16SS102J RAB4CQ221J RAB4CQ221J RAB4CQ221J RS1/16SS221J RS1/16SS221J RS1/16SS221J RAB4CQ221J RS1/16SS221J RS1/16SS221J RS1/16SS0R0J RS1/16SS0R0J RS1/16SS102J

Circuit Symbol and No.


C 217 C 218 C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 219 220 221 222 223 224 225 226 227 228 234 237 239 242 243 244 246 251 260 301 302 303 304 305 307 601 602 701 703 706 707 712 714 716 722 723 903 906 907 910 (A,28,12) (A,25,7) (A,34,7) (A,33,11) (B,35,6) (B,35,8) (B,33,8) (B,40,16) (B,45,14) (B,43,12) (A,45,10) (A,49,9) (B,36,81) (B,38,29) (B,34,10) (B,58,32) (B,39,76) (B,49,70) (A,23,19) (B,28,31) (A,54,25) (A,43,78) (A,50,79) (A,37,85) (A,39,89) (B,34,92) (B,56,90) (B,46,60) (B,41,65) (A,64,46) (B,50,61) (B,50,62) (A,36,45) (A,22,42) (B,60,45) (A,61,40) (B,52,48) (A,26,41) (B,56,70) (A,40,77) (A,47,76) (B,60,71)

Part No.
CKSSYB104K10 CKSSYB473K10 CKSSYB104K10 CKSSYB182K50 CKSSYB104K10 CCSSCH560J50 CCSSCH4R0C50 CKSSYB104K10 CKSSYB103K16 CCSSCH680J50 CCSSCH470J50 CKSSYB103K16 CEVW221M4 CKSSYB104K10 CCSSCH220J50 CKSSYB104K10 CKSSYB104K10 CKSSYB104K10 CKSSYB104K10 CKSRYB102K50 CKSSYB104K10 CKSSYB221K50 CKSSYB221K50 CKSSYB472K25 CKSSYB103K16 CEVW101M16 CKSSYB104K10 CCSRCH102J50 CCSRCH102J50 CKSSYB104K10 CKSSYB103K16 CKSSYB104K10 CKSSYB104K10 CKSRYB224K16 CKSSYB104K10 CKSSYB103K16 CKSQYB475K6R3 CKSRYB105K10 CKSSYB471K50 CKSRYB224K16 CKSSYB103K16 CKSQYB225K10
A

Miscellaneous Parts List


M 1 M 2 Pickup Unit(P10)(Service) Motor Unit(SPINDLE) CXX1641 CXC4440 Motor Unit(LOADING/CARRIAGE) CXB8933
E

CAPACITORS
C C C C C C C C C C 103 105 108 110 201 202 203 204 205 208 (B,14,8) 100F/16V (A,19,15) (B,39,16) (A,18,6) (A,51,14) (B,50,17) (A,55,23) (B,28,22) (A,53,25) (B,44,25) (A,54,29) (A,45,37) (A,25,8) CCH1504 CKSSYB104K10 CKSSYB104K10 CKSSYB104K10 CKSSYB102K50 CKSSYB104K10 CKSSYB104K10 CEVW220M6R3 CKSSYB104K10 CKSSYB104K10

C 209 C 212 C 216

CKSSYB104K10 CKSRYB105K10 CKSSYB332K50

DEH-P4750MP/XM/GS
5 6 7 8

49

6. ADJUSTMENT
6.1 CD ADJUSTMENT
A

1) Cautions on adjustments In this product the single voltage (3.3V) is used for the regulator. The reference voltage is the REFO1 (1.65V) instead of the GND. If you should mistakenly short the REFO1 with the GND during adjustment, accurate voltage will not be obtained, and the servos misoperation will apply excessive shock to the pickup. To avoid such problems: a. Do not mix up the REFO1 with the GND when connecting the (-) probe of measuring instruments. Especially on an oscilloscope, avoid connecting the (-) probe for CH1 to the GND. b. In many cases, measuring instruments have the same potential as that for the (-) probe. Be sure to set the measuring instruments to the floating state. c. If you have mistakenly connected the REFO1 to the GND, turn off the regulator or the power immediately. Before mounting and removing filters or leads for adjustment, be sure to turn off the regulator. For stable circuit operation, keep the mechanism operating for about one minute or more after the regulator is turned on. In the test mode, any software protections will not work. Avoid applying any mechanical or electrical shock to the mechanism during adjustment. The RFI and RFO signals with a wide frequency range are easy to oscillate. When observing the signals, insert a resistor of 1k ohms in series.

2) Test mode This mode is used to adjust the CD mechanism module. To enter the test mode. While pressing the 4 and 6 keys at the same time, reset. To exit from the test mode. Turn off the ACC and back up. Notes: a. During ejection, do not press any other keys than the EJECT key until the loaded disc is ejected. b. If you have pressed the () key or () key during focus search, turn off the power immediately to protect the actuator from damage caused by the lens stuck. c. For the TR jump modes except 100TR, the track jump operation will continue even if the key is released. d. For the CRG move and 100TR jump modes, the tracking loop will be closed at the same time when the key is released. e. When the power is turned off and on, the jump mode is reset to the single TR (91), the RF amp gain is set to 0dB, and the auto-adjustment values are reset to the default settings.

The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it.

50

DEH-P4750MP/XM/GS
1 2 3 4

- Flow Chart
[KEY] Contents Display [4]+[6]+Reset or [4]+[6]+BU+ACC Test Mode In

[CD]or[SOURCE] Source On
TRK MIN SEC

[BAND] Power On
(T.Offset is adjusted)
TRK 00 MIN00 SEC 00

[3] Power On
(T.Offset is not adjusted)
TRK 99 MIN 99 SEC 99

[2] RF AMP *1 Gain switching


TRK GGMIN GGSEC GG

[4] SPINDLE *9 Speed switching


TRK SP MIN SP SEC SP

B
[BAND] Power Off
TRK MIN SEC

[3] Focus Close S curve check


TRK

91 MIN91 SEC 91

[6] Focus Mode *2 switching TRK 0x MIN0x SEC 0x

[1] Tracking Servo Close


TRK

[] CRG+
TRK

[] *8
TRK

[2] *8
Automatic adjustment switching *3
TRK

CRGor
TRK

or

TRK

00 MIN00 SEC00 99 MIN99 SEC99

or

TRK

00 MIN00 SEC00 99 MIN99 SEC 99

00 MIN00 SEC00 99 MIN 99 SEC 99

?? MIN?? SEC ??

[BAND] Power Off


TRK MIN SEC

[1]
T.Close and AGC
Applicable servomechanism
TRK MIN SEC TRK

[6]
T.Close
Applicable servomechanism
MIN SEC

[3] RF AGC /
RF AGC coefficient display
TRK ?? MIN ?? SEC ??

[] CRG+
TRK8x MIN8x SEC8x

[] CRGTRK8x MIN8x SEC8x

[2]
T.Balance adjustment /
T.BAL coefficient display
TRK ?? MIN?? SEC ??

?tr

?min ?sec

?tr

?min ?sec

or

TRK 9x MIN 9x SEC 9x

or

TRK 9x MIN 9x SEC 9x

C
[BAND] Power Off
TRK MIN SEC

[1] F,T,RF AGC *7


F.Bias display switching
TRK

[3] F,T AGC / F.Bias RF AGC


TRK

[6]
CRG/TR Jump *5 value switching
TRK

[] *4 CRG/TR Jump +
TRK

[] *4 CRG/TR Jump TRK

[2] Tracking Open


TRK

?? MIN?? SEC ??

?tr

MIN

?min ?sec

SEC

?tr

MIN

?min ?sec

SEC

?tr

MIN

?min ?sec

SEC

?tr

MIN

?min ?sec *6

SEC

or

TRK

8x MIN8x SEC 8x 9xMIN 9xSEC 9x

[BAND] Power Off


TRK MIN SEC

[2] Tracking Open


TRK8x MIN8x SEC8x

or

TRK 9x MIN 9x SEC 9x

*1)
TRK

TYP
MIN SEC

-6dB
TRK 06 MIN 06 SEC 06

-12dB
TRK 12 MIN 12 SEC 12

[Key]

Operation Test Mode

*2) Focus Close

S.Curve check setting


TRK 01 MIN 01 SEC 01

F EQ measurement setting
TRK 02 MIN 02 SEC 02

[BAND] Power On / Off [] CRG + / TR Jump + (Direction of the external surface) CRG - / TR Jump (Direction of the internal surface) U.CLS and AGC and Applicable servomechanism / AGC, AGC display setting RF Gain switching / Offset adjustment display / T.Balance adjustment / T.Open Close, S.Curve / Rough Servo and RF AGC / F, T, RF AGC SPDL 1X / 2X switching As for the double speed (2x), audio output cannot be supported. Error Rate measurement 1st - ON : ERR count Beginning (30Sec) 2nd - ON : BER display data [%]

TRK 00 MIN 00 SEC 00 (TRK 99 MIN 99 SEC 99)

*3) F.Offset Display T.Offset Display Switch to the order of the original display [] *4) 1TR / 32TR / 100TR [1] [2] *5) Single TR 32TR 100TR CRG Move 9x(8x) : 91(81) 92(82) 93(83) 94(84) *6) Only at the time of CRG move, 100TR jump [5] *7) TRK/MIN/SEC F.AGC T.AGC F Bias RF AGC [6] [3] [4]

F.Mode switching / Tracking Close / CRG TR Jump switching

*8) CRG motor voltage = 2[V]

*9) Applicability : A, B, C, D, E, F TYP(1X) 2X


TRK MIN SEC TRK 22 MIN 22 SEC 22

1X
TRK 11 MIN 11 SEC 11

Applicability : G TYP(2X)
TRK MIN SEC

1X

2X
TRK 22 MIN 22 SEC 22

TRK 11 MIN 11 SEC 11

As for the double speed (2x), audio output cannot be supported

DEH-P4750MP/XM/GS
5 6 7 8

51

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT


A

Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below. Purpose : To check that the grating is within an acceptable range when the PU unit is changed.
B

Symptoms of Mal-adjustment : If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching. Method : Measuring Equipment Measuring Points Disc Mode

Oscilloscope, Two L.P.F. E, F, REFO1 TCD-782 TEST MODE

CD CORE UNIT(S10.1)
C
L.P.F. E VREF Xch 100k 390pF Ych

Oscilloscope

F VREF

100k 390pF L.P.F.

D
F E REFO1

Checking Procedure 1. In test mode, load the disc and switch the 3V regulator on. 2. Using the and buttons, move the PU unit to the innermost track. 3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the fourth press. 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75 . Refer to the photographs supplied to determine the phase angle. 5. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the mechanism should be judged to be at fault. Note Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble".

52

DEH-P4750MP/XM/GS
1 2 3 4

Grating waveform

Ech Xch 20mV/div, AC Fch Ych 20mV/div, AC


A

30

45

60

75

90

DEH-P4750MP/XM/GS
5 6 7 8

53

6.3 ERROR MODE


- Error Messages
A

Error is displayed with number for Error cause when CD is inoperative or stops with Error during operation. The purpose is to reduce nonsense calls from users as well as to assist all related analysis and repair for defects at service station. (1) Basic Display Method 1) When CSMOD (CD mode area for system) is SERRORM, Error code will be written in DMIN (minutes area for display), DSEC (seconds area for display). The same data shall be written in DMIN and DSEC. DTNO is blank as usual. 2) Display Example of Head Unit The following is about LCD display ability. xx is Error number.

8 digits ERRORxx

6 digits ERRxx OR Errxx

4 digits Exx

(2) Error Code List No. Classification Contents 10 Electricity Carriage Home NG
C

11 12

Electricity Electricity

Focus Search NG Spindle Lock NG Subcode NG RF-amp NG

Details Cause CRG cant move to the inner. CRG cant move from the inner. HOME SW failure, CRG movement failure. Focus cant be caught. Back of Disc / Severe dirt and vibration. Not spindle, lock. Wrong subcode (cant read). Defective Spindle. Scratch and dirt on Disc. Intense vibration. The appropriate gain of the RF amp cannot be obtained. Defective spindle. Scratched or dirty disc. Severe vibration. Abnormal CD signals. Blanc CD-R disc. Disc inserted upside down. AGC protection doesnt work, out of Focus soon. Scratch on Disc/Severe dirt and vibration. There is no playable MP3 or WMA file present in a disc. No MP3 or WMA file exists in a CD-ROM disc inserted. Contents are stored in an incompatible file format. The contents in a CD-ROM disc inserted are recorded in a file format other than ISO9660 Level-1 and 2. Cant reach the target address. Defective CRG/tracking, or scratch on Disc. There is no playable TRK No. present in a disc. All TRK Nos. In a disc inserted are specified as a track which should be skipped, in the track skip information. Disc loading/ejection cannot be complete. Foreign objects entered into the mechanism. Disc caught in between during loading/ejection.

17 22 23

Electricity Disc Disc

Setup NG Impossible to play File Format NG

30 44

Electricity Disc

Search Time Out Impossible to play

50

Mecha

Disc Load / Eject NG

Power supply (VD) isnt connected to the ground. Defective SW transistor. Abnormal power (failed connector) Note : Error doesnt display in mechanism only. (CD off causes mechanism off) If TOC cant be read, error wouldnt occur, but mechanism still continues its operation. The upper digits of error code is mainly classified by 3 kinds as follows: 1x: Setup related error, 3x: Search related error, Ax: Other errors.

A0

System

Power NG

54

DEH-P4750MP/XM/GS
1 2 3 4

6.4 SYSTEM MICROCOMPUTER TEST PROGRAM


A

- PCL Output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode cancelled), shift the TESTIN (Pin 5) terminal to H. The clock signal is output from the PCL terminal (Pin 62). The frequency of the clock signal is 786.432kHz that is one 16th of the fundamental frequency. The clock signal should be 786.432kHz 31.5Hz. If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.

DEH-P4750MP/XM/GS
5 6 7 8

55

7. GENERAL INFORMATION
7.1 DIAGNOSIS
A

7.1.1 DISASSEMBLY
- Removing the Case (not shown) 1. Remove the Case.

- Removing the CD Mechanism Module (Fig.1)

CD Mechanism Module

1
B

Remove the four screws.

Disconnect the connector and then remove the CD Mechanism Module.

1 1

- Removing the Grille Assy (Fig.1)

Remove the two screws and then remove the Grille Assy.

2
C

1 1

Grille Assy
- Removing the Tuner Amp Unit (Fig.2)

Fig.1

1
D

Remove the screw.

2 2

2 3 4

Remove the three screws.

Straighten the tabs at three locations indicated. Remove the screw and then remove the Tuner Amp Unit.

4 1

Tuner Amp Unit


F

Fig.2

56

DEH-P4750MP/XM/GS
1 2 3 4

- How to hold the Mechanism Unit


1. Hold the top and bottom frame. 2. Do not squeeze top frame's front portion too tight, because it is fragile.
A

Do not squeeze.

- Removing the Upper and Lower Frames


1. With a disc clamped, remove the four springs (A), the two springs (B), the two springs (C), and the four screws. 2. To remove the upper frame, open it on the fulcrum A. 3. While lifting the carriage mechanism, remove the three dampers. 4. With the frames removed, insert the connectors coming from the main unit and eject the disc. Caution: Before installing the carriage mechanism in the frames, be sure to apply some alcohol to the dampers and set the mechanism to the clamp mode. Carriage Mechanism B Damper Lower Frame B A Damper Damper C
D

A C

Upper Frame
A

DEH-P4750MP/XM/GS
5 6 7 8

57

- Removing the Pickup Unit


A

1. Apply shorting solder to the Pickup flexible cable. Disconnect the cable. 2. Set the mechanism to the clamp mode. 3. Remove the lead wires from the inner holder. 4. Remove the washer, styling holder, change arm, and pickup lock arm. 5. While releasing from the hook of the inner holder, lift the end of the feed screw. Caution: In assembling, move the planet gear to the load/eject position before setting the feed screw in the inner holder.

Shorting Solder

Washer Pickup Lock Arm Styling Holder Change Arm

Feed Screw

Inner Holder Planet Gear

58

DEH-P4750MP/XM/GS
1 2 3 4

7.1.2 CONNECTOR FUNCTION DESCRIPTION

1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16
8 9 10 11

10A

5 6

1 2 3 4

FRONT OUTPUT (DEH-P4770MP/XM/CS) REAR OUTPUT ANTENNA JACK

POWER SUPPLY SPEAKER OUTPUT

IP-BUS

POWER SUPPLY, SPEAKER OUTPUT Pin No. Pin No. 9 1 FR+ 10 2 RR+ 11 3 FR12 4 RR13 5 FL+ 14 6 RL+ 15 7 FL16 8 RLIP-BUS Pin No. 1 2 3 4 5 6

NC NC B.REM NC NC ACC GND B.UP

BUS+ GND GND NC BUSGND

Pin No. 7 8 9 10 11

BUS L+ INPUT ASENB BUS R+ INPUT BUS R- INPUT BUS L- INPUT

DEH-P4750MP/XM/GS
5 6 7 8

59

7.2 PARTS
7.2.1 IC
A

- Pin Functions (PE5465A)


Pin No. 1 2-4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29-31 32 33 34 35 36 37 38,39 40 41 42-45 46 47 48 49-55 56,57 58 59-61 62 63 64 65 66 67 68 69,70 71 72 73 74 75 Pin Name swvdd NC TESTIN LCDPW TELIN ejectin FLPILM dalmon reset XT2 XT1 VSS X2 X1 REGOFF REGC VDD ILMPW SYSPW ADPW NC IPPW NC ROMDATA ROMCLK ROMCS NC tunpce@ VST VCK VDT NC mute NC VSS VDD NC DORAON NC CSENSOUT NC ROT1,0 STRKEY2 NC PCL BRXEN BSRQ TSCK/BSCK TSI/BSI BSO BRST NC ASENSBO EMUTE TEST SL STRKEY1 I/O O I O I I O O I I Function and Operation Grille : Chip enable output Not used Test program mode input Not used Telephone mute input Eject sense input Flap illumination output For consumption low-current output Reset input Not used Clock connection pin GND Crystal oscillator connection pin Crystal oscillator connection pin Regulator operation specification signal input Capacitor for regulator connect pin Power supply Illumination power supply control output System power control output A/D converter power supply control output Not used Power supply control output for IP BUS interface IC Not used ROM correction data input/output Not used Not used Not used PLL chip enable output2 E.VOL : Strobe output E.VOL : Clock output E.VOL : Data output Not used System mute output Not used GND Power supply Not used Not used Not used CSENS state output Not used Rotary encoder pulse input 1,0 Steering remote controller input Not used Clock adjustment output P-BUS : Reception enable input/output P-BUS : Service request input P-BUS : Serial clock output P-BUS : Serial data input P-BUS : Serial data output P-BUS : Reset output Not used IP-BUS : Slave power supply control output Not used GND TUNER : Signal level input Steering remote controller input

I I

O O O O I/O O O O O O O O

O O I I O I/O I O I O O O I I I

60

DEH-P4750MP/XM/GS
1 2 3 4

Pin No. 76 77 78-81 82 83 84 85 86 87 88,89 90 91 92 93 94 95 96 97 98 99 100 * PE5465A 100

Pin Name MODELIN CSENS NC AVDD AVREF AVSS RX TX NMI NC dsens NC asens bsens TUNPDI KYDT DPDT TUNPCK TUNPDO TUNPCE BEEP

I/O I I

O I O I I I I I I O O O O O

Function and Operation Model select input Flap close sense input Not used A/D converter power supply terminal A/D converter reference voltage terminal GND IP-BUS : Data input IP-BUS : Data output GND Not used Grille detach sense input Not used ACC power sense input Back up power sense input PLL IC data input Grille data input Grille data output PLL clock output PLL data output PLL chip enable output Beep tone output

81

80

IC's marked by * are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction.

30 31 50

51
D

N.C.

STB 8
BIAS

VCC 7

BUS+ 6

BUS5

+ -

DRIVER OUTPUT

N.C. 4

HA12240FP

BD4834G

E
Vref
+
COM

VOUT

VDD

1 S1

2 R

3 S2

4 GND

GND

RECEIVER OUTPUT

DEH-P4750MP/XM/GS
7 8

61

- Pin Functions(PD6340A)
A

Pin No. 1-5 6-9 10 11-14 15,16 17 18 19 20 21 22 23 24 25,26 27 28 29-32 33-55 56 57-64 * PD6340A 1

Pin Name SEG4-0 COM3-0 VLCD KST3-0 KDT0,1 REW DPDT NC KYDT MODA X0 X1 VSS KDT2,3 NC KST4 NC SEG35-13 VDD SEG12-5

I/O O O O I I I O

I O O O

Function and Operation LCD segment output LCD common output LCD drive power supply Key strobe output Key data input (analogue input) Remote control reception input Display data input Not used Key data output GND Crystal oscillator connection pin Crystal oscillator connection pin GND Key data input Not used Key strobe output Not used LCD segment output Power supply LCD segment output

16

64

17

49 48
D

32 33

NJM2388F84

62

DEH-P4750MP/XM/GS
1 2 3 4

- Pin Functions(UPD63763GJ)
Pin No. 1 2 3 4-8 9-16 17 18 19 20 21 22 23, 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39-41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73-88 89-99 Pin Name D.VDD D1.GND reset AB12-8 AD7-0 cs ASTB read write wait INTQ IFMODE0, 1 D1.VDD DA.VDD ROUT DA.GND REGC DA.GND LOUT DA.VDD X.VDD XTAL xtal X.GND VDDREG15 PWMSW0 TEST3-1 PWMSW1 TESTEN D1.GND DIN DOUT SCKIN SCKO LRCKIN LRCK xtalen D1.VDD RFCK/HOLD WFCK/MIRR PLCK/RFOK LOCK/RFOK C1D1/C8M C1D2/C16M C2D1/RMUTE C2D2/LMUTE C2D3/SHOCK D1.GND C33M (rcs) RA11 (CKE) ras cas)(LDQM) cas!(UDQM) we oe(cas) D.GND RDB0-15 RA0-10 I/O Function and Operation Power supply for digital circuits GND for 1.6V digital circuits Input of reset Address bus 12-8 from the microcomputer Address/data bus 7-0 to the microcomputer Chip selection Address strobe Control signals(read) Control signals(write) Control signals(wait) Interruption signals to the external microcomputer Switching the microcomputer I/F 0, 1 Power supply for 1.6V digital circuits Power supply for DAC Output of audio for the right channel GND for DAC Connected to the capacitor for band gap GND for DAC Output of audio for the left channel Power supply for DAC Power supply for the crystal oscillator Connected to the crystal oscillator(16.9344MHz) Connected to the crystal oscillator(16.9344MHz) Ground for the crystal oscillator Control of 1.6V regulator Setup 0 for PWM output(SD, MD) Connected to GND Setup 1 for PWM output(FD, TD) Connected to GND GND for 1.6V digital circuits Input of audio data Output of audio data Clock input for audio data Clock output for audio data Input of LRCK for audio data Output LRCK for audio data Permission to oscillate 16.9344MHz Power supply for 1.6V digital circuits Output of RFCK/HOLD signal Output of WFCK/MIRR signal Output of PLCK/Output of RFOK Output of LRCK/Output of RFOK Information on error correction/C8M : 8MHz Information on error correction/C16M : 16MHz Information on error correction/Mute for Rch Information on error correction/Mute for Lch Information on error correction/Detection of vibration GND for 1.6V digital circuits Output of 33.8688MHz(CLK for SDRAM) DRAM cs Output of DRAM address 11 Output of DRAM CKE Output of DRAM ras Output of DRAM lower cas(LDQM) Output of DRAM upper cas(UDQM) Output of DRAM we Output of DRAM oe(cas) Ground for digital circuits Input/output of DRAM data0-15 Output of DRAM address0-10
A

I I I/O I I I I O O I

I O

I I I I I O I O I O I O O O O O O O O O O O O O O O O O O I/O O

DEH-P4750MP/XM/GS
5 6 7 8

63

Pin No. 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120, 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144

Pin Name D.VDD FD+ FDTD+ TDSD+ SDMD+ MDREFOUTSV AD.VDD EFM ASY ATEST RFI AD.GND AGCO C3T AGCI RFO EQ2, 1 RF2RFA.GND A C B D F E VREFIN A.VDD REFOUT REFC FEFEO ADIN TETEO TE2 TEC LD PD D.GND

I/O O O O O O O O O O O I O I O O I O I I I I I I I I I I O I I O I I O O I O I

Function and Operation Power supply for digital circuits Output of focus drive PWM + Output of focus drive PWM Output of tracking drive PWM + Output of tracking drive PWM Output of thread drive PWM + Output of thread drive PWM Output of spindle drive PWM + Output of spindle drive PWM REFOUT for servo Power supply for ADC Output of EFM signals Input of asymmetry Analog tests Input of RF Ground for the analog system Output of RF Connection to the capacitor for detecting 3T Input of AGC Output of RF(AGC) Equalizer 2, 1 Reversal input of RF2 Reversal input of RF Ground for the analog system Input of A Input of C Input of B Input of D Input of F Input of E Input of reference voltage Power supply for the analog system Output of reference voltage Connected to the capacitor for output of REFOUT Reversal input of FE Output of FE Input of FE, TE A/D converter Reversal input of TE Output of TE TE2 TEC Output of LD Input of PD Ground for digital circuits

* UPD63763GJ 108 73 72 37 1 36

109

144
F

64

DEH-P4750MP/XM/GS
1 2 3 4

- Pin Functions(PE5454A)
Pin No. 1 2 3 4 5 6, 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35, 36 37 38 39-42 43 44 45 46 47 48 49 50 51 52 53 54 55 56-58 59 60 61 62 63 64 65 66 Pin Name AVREF AVSS RFOK NC EVDD NC IC/FLMD0 VDD REGC VSS X1 X2 reset XT1 XT2 NC NC xint NC brst BSI BSO bsck FTXD FRXD BRXEN bsrq NC DSCSNS 8EJ(S905) 12EJ(S904) EVSS EVDD SRAMLEVEL0, 1 EMPH emph NC adena LRCKOK SRAMLEVEL2 CD3VON CONT xrst VDCONT ROMDATA ROMCS ROMCK LOEJ CLCONT CDMUTE NC xcs NC xwait CLKOUT LOCK NC xwrite NC I/O Format Function and Operation A power supply Positive power supply(5V) A power supply GND Output of state of RFOK Not used E power supply Positive power supply Not used IC : VSS direct connection/FLMOD0 : Pull-down Positive power supply(5V) Connected to the capacity stabilizing output of the regulator GND Oscillator connection for mainclock Oscillator connection for mainclock System reset input Connected to the oscillator for subclock (connected to VSS via the resistor) Connected to the oscillator for subclock(Open) Connected to EVDD or EVSS via the resistor Not used CD LSI interruption signal input Connected to VSS via the resistor P-Bus reset input P-Bus serial data input P-Bus serial data output P-Bus serial clock input/output For flash rewriting(transmitted signal) For flash rewriting(received signal) It is possible to receive P-Bus P-Bus service request demand Not used Disc state sense input Input of detection of 8 cm disc ejection Input of detection of 12 cm disc ejection E power supply GND E power supply Positive power supply SRAM level meter output Emphasis information output Emphasis information output Not used A/D reference voltage supply control output (DOUT mute output) SRAM level meter output CD +3.3V power supply control output Servo driver power supply control output CD LSI reset control output VD power supply control output E2PROM data input/output E2PROM chip selection output E2PROM clock output The direction change output of LOAD/EJECT Driver input change output CD mute control output Not used CD LSI chip selection output Not used CD LSI write control signal output Internal system clock output(Open) Spindle lock input Not used CD LSI write control signal output Not used
A

I I I

C I I O I/O O I I/O I/O I I I

C /C C /C /C

O O O O O O O O O O I/O O O O O O O I O I O

C C C C C C C C C C /C C C C C C C

DEH-P4750MP/XM/GS
5 6 7 8

65

Pin No. 67 68 69 70 71-83 84-86 87 88 89-93 94 95 96 97 98 99 100 * PE5454A

Pin Name xread XASTB BVSS BVDD AD0-12 NC FMODE FLRQ NC csens TYPE_A/D testin HOME TEMP VDSENS NC

I/O O O

Format

I/O I O I I I I

/C

Function and Operation CD LSI read control signal output CD LSI address strobe output B power supply GND B power supply Positive power supply Address/data Bus 0-12 Not used For flash rewriting Connected to VSS via the resistor For flash rewriting Not used Flap closing sense input CD-DA analog/digital output change setup Chip check test program starting input Home SW sense input Temperature information sense input VD power supply short sense input Not used

Format C 50

Meaning CMOS

76

75

51 26 25
Thermal Protection Bandgap Reference 1 IN 2 GND

100 1
D

NJM2885DL1-33

-+
3 OUT

66

DEH-P4750MP/XM/GS
1 2 3 4

- FM/AM Tuner Unit


7 6
WC CE2

13
ROM_VDD

5
SL

10 9 8
CE1 DI CK

11
NC

14
DO

18 19 20 21
NC NC NC NC

5V

OSC

LPF

AM ANT 1 ATT

FMRF Rch IC 2 2.5V Lch DET, FM MPX

FM ANT ATT FMRF ANT adj RF adj

IC 1 3.3V MIXER, IF AMP

T51

CF52 CF51

AUDIOGND

OSCGND

VDD_3.3

RFGND

DGND

3.3V

IC 4 3.3V 2.5V 2.5V

12

15

22

16

VCC

NC

17

No. Symbol 1 AMANT

I/O Explain I AM antenna input

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

RFGND FMANT VCC SL CE2 WC CE1 CK DI NC OSCGND ROM_VDD

I O I I I I I

RF ground FM antenna input power supply signal level chip enable-2 write control chip enable-1 clock data in non connection osc ground power supply data out digital ground non connection power supply non connection non connection non connection non connection audio ground L channel output R channel output

DO O DGND NC VDD_3.3 NC NC NC NC AUDIOGND L ch O R ch O

AM antenna input high impedance AMANT pin is connected with an all antenna by way of 4.7H. (LAU type inductor) A series circuit including an inductor and a resistor is connected with RF ground for the countermeasure against the hum of power transmission line. Ground of antenna block Input of FM antenna 75 Surge absorber(DSP-201M-S00B) is necessary. The power supply for analog block. D.C 8.4V 0.3V Output of FM/AM signals level Chip enable for EEPROM Low active You can write EEPROM, when EEPROM write control is Low. Ordinary non connection Chip enable for AFRF High active Clock Data input Not used Ground of oscillator block Power supply for EEPROM pin 13 is connected with a power supply of micro computer. Data output Ground of digital block Not used The power supply for digital block. 3.3V 0.2V Not used Not used Not used Not used Ground of audio block FM stereo L-ch signal output or AM audio output FM stereo R-ch signal output or AM audio output

DEH-P4750MP/XM/GS
5 6 7 8

IC 3 EEPROM 5.0V

IC 5 3.3V

24

23

67

SEG39 SEG38 SEG37 SEG36

COM 3 COM 2 COM 1 COM 0

COM3 COM2 COM1 COM0 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0

68

7.2.2 DISPLAY

- LCD(CAW1852)(DEH-P4750MP/XM/GS, DEH-P4790MP/XM/ID) - LCD(CAW1851)(DEH-P4770MP/XM/CS)

2 2

DEH-P4750MP/XM/GS COMMON SEGMENT


3 4

7.3 OPERATIONAL FLOW CHART


Power ON
A

VDD=5V Pin 19, 41

bsens Pin 93
B

bsens=L asens Pin 92 asens=L dsens Pin 90 dsens=L ASENSBOH Pin 71


C

CSENS Pin 77 2V < CSENS < 3V Starts communication with Grille microcomputer. 300ms swvddL Pin 1

- CSENS < 2V, 3V < CSENS = = Last source returns. CD loading functions are available. Keys except for EJECT key are not available.
D

300ms In case of the above signal, the communication with Grille microcomputer may fail. If the time interval is not 300msec, the oscillator may be defective.
E

Source keys operative

Source ON

SYSPWH Pin 21

Completes power-on operation. (After that, proceed to each source operation)


F

DEH-P4750MP/XM/GS
5 6 7 8

69

7.4 CLEANING
A

Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned CD pickup lenses Cleaning tools Cleaning liquid : GEM1004 Cleaning paper : GED-008

70

DEH-P4750MP/XM/GS
1 2 3 4

8. OPERATIONS
A

DEH-P4750MP/XM/GS
5 6 7 8

71

72

DEH-P4750MP/XM/GS
1 2 3 4

DEH-P4750MP/XM/GS
5 6 7 8

73

74

DEH-P4750MP/XM/GS
1 2 3 4

DEH-P4750MP/XM/GS
5 6 7 8

75

76

DEH-P4750MP/XM/GS
1 2 3 4

DEH-P4750MP/XM/GS
5 6 7 8

77

Fixing the front panel


A

If you do not operate the removing and attaching the front panel function, use the supplied fixing screws and holders to fix the front panel to this unit.

1. Attach the holders to both sides of the front panel.


Holder CXX1644 Holder CXX1645

2. Replace the front panel to the unit.

3. Flip the holders into upright positions.

4. Fix the front panel to the unit using fixing screws.

Fixing Screw CXX1646

78

DEH-P4750MP/XM/GS
1 2 3 4

This product Rear output IP-BUS input (Blue) Fuse Antenna jack Multi-CD player (sold separately) IP-BUS cable

Connecting cords with RCA pin plugs (sold separately) Power amp (sold separately)

- Connection Diagram(DEH-P4750MP/XM/GS, DEH-P4790MP/XM/ID)

5
Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC). White Front speaker White/black Left Green Rear speaker Green/black Violet/black Violet Rear speaker Gray/black Right Gray Front speaker Rear speaker With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers. Rear speaker Perform these connections when using the optional amplifier.

System remote control

6 E A D C B

Yellow To terminal always supplied with power regardless of ignition switch position.

DEH-P4750MP/XM/GS

Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF.

Black (ground) To vehicle (metal) body.

7 8

79

80
IP-BUS cable
Connecting cords with RCA pin plugs (sold separately) Power amp (sold separately) This product Rear output (REAR OUTPUT) Antenna jack Fuse Front output (FRONT OUTPUT) Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC). System remote control IP-BUS input (Blue) Power amp (sold separately)

Multi-CD player (sold separately)

- Connection Diagram(DEH-P4770MP/XM/CS)

1
White + Front speaker Left + Rear speaker Green/black Violet/black With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers. White/black Green Gray/black Violet + Rear speaker Right Gray + Front speaker Perform these connections when using the optional amplifier. + Rear speaker Left + Front speaker + Front speaker Right + Rear speaker

Yellow To terminal always supplied with power regardless of ignition switch position.

Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF.

DEH-P4750MP/XM/GS

Black (ground) To vehicle (metal) body.

DEH-P4750MP/XM/GS
5 6 7 8

81

- Jigs List
Name Test Disc L.P.F. Jig No. TCD-782 Remarks Checking the g g grating g Checking the g g grating (Two pieces) g( )

82

DEH-P4750MP/XM/GS
1 2 3 4

You might also like