You are on page 1of 5

EEE 267 CT 1 Time: 20 minutes

Name: Student No. Q1. Calculate the value of VR1 from the following circuit circuit. (Assume constant voltage drop model for the given models diodes D1 and D2 with cut-in voltage, V = 0.70 V) in 8 Q2. Consider vs(t)=10 sin (100 t) volt in the following circuit. (Assume constant voltage drop model for the given diode D1 with cut voltage, V = 0.70 V) cut-in

(a) Draw the wave wave-shapes of the input (vs(t)) and output )) (v0(t)) voltages superimposed in a same plot. t)) 6

(b) Also sketch the voltage transfer characteristics of the following circuit. 6

v0

vs

EEE 267 CT 2 Time: 20 minutes


Name: Student No. Q1. Fig.1 shows a circuit diagram of a clipper circuit. The applied sinusoidal voltage vs(t) is 10 sin (2000 t) voltage. The voltage wave-shapes of the input (vs(t)) and output (v0(t)) voltages are shown in Fig. 2 superimposed on each other. Now, calculate the value of DC voltage sources V1 and V2 shown in Fig. 1. (Assume constant voltage drop models for the given diodes D1 and D2 with cut-in voltage, V = 0.70 V) (8) Q2. Also calculate the value of tD1 and tD2 using the information in Figs. 1 and 2. (12)

Fig. 1: Circuit diagram

Fig. 2: Waveforms of vs(t) and vo(t)

Student No. Q1. In the following circuit shown in Fig. 1, it is given that VCC=10V, RB=10K, RC=5K and V0=10V. Now tick on the correct answer: The npn transistor is operating on a) cut-off mode off b) saturation mode c) Forward-active operating mode active

(8)

Q2. In the following circuit shown in Fig. 1, consider VCC=10V, RB=100K, RC=1K, VBB=5V and = 100. Now, calculate the K, value of V0 (17)

Fig. 1: Circuit diagram

Student No. Q1. In the following circuit shown in Fig. 1, it is given that VCC=10V, RB=10K, RC=5K and V0=10V. Now tick on the correct answer: The npn transistor is operating on a) cut-off mode off b) saturation mode c) Forward-active operating mode active

(8)

Q2. In the following circuit shown in Fig. 1, consider VCC=10V, RB=100K, RC=1K, VBB=5V and = 100. Now, calculate the . K, . value of V0 (17)

Fig. 1: Circuit diagram

EEE 267 CT 4

A separately excited dc generator with a field current of 2.5 amp, when running at 1200 rpm supplies 200 amp at 125V to a load circuit of constant resistance. Armature resistance is 0.04 and total drop at brushes is 2V. Determine the i) Generated voltage (5) ii) Value of constant resistance (5) Now the speed is increased to 1600 rpm and the field current is reduced to 80%. The relation between the field current (If) in amp and produced field flux () in Wb can be expressed as = 1-exp(-If). Calculate iii) Changed generated voltage (5) iv) Changed current in load circuit (10)

EEE267 CT5
Name: Student No.

The equivalent low-side parameters of a 250-KVA, 480-4160V, 60-Hz transformer are Req,LS= 0.00920 and Xeq,LS= 0.00920 . The transformer is operating in the step-up mode and is delivering half of the rated current at rated voltage to a 0.9 pf leading. Determine the voltage regulation.

You might also like