Professional Documents
Culture Documents
Orkel AS
N 7320 Fannrem
Delivery and warranty registration form has to be filled out of dealer together with customer. The dealer has to send one of the three forms back to the manufacturer. Without filled out and sent back form, the warranty is not valid.
Congratulations with your Combi Balewrapper Orkel GP 1250 Agronic! Orkel machines are known for their quality and strength. Thats a result of continuous development and a thorough quality control before the machine is sent out from the factory. The machine is CE-marked (declaration of conformity) in accordance to the machine directive.
You have to read the Users manual and the Safety instructions carefully before using the machine.
Orkel AS
V 1.0
Content
WARRANTY Dear Customer: 1.0 Putting the machine to work 1.1 Hydraulics 1.2 Electronics 1.3 Control box 2.0 Control box (program ver. 1.0) 2.1 General 2.2 Keypad 2.3 Automatic wrapping 2.4 Selecting the automatic operation mode 2.5 Manual control of functions 2.6 Manual control during automatic operation 2.7 Manual control after interrupted automatic operation 2.8 Display during manual control 2.9 Display during automatic operation 2.10 Error conditions 3.0 Adjustments of the hydraulics 3.1 Adjusting film overlap, speed of wrapping and other operations 4.0 Side tipper Operating principle 5.0 Changing the wrapping film roll 6.0 Adjusting the film cutter 7.0 Operation 7.1 General 7.2 Loading, wrapping and removing of bales 7.3 When the film runs out in the middle of wrapping 7.4 If the wrapper arm hits an obstacle 7.5 Transport 8.0 Maintenance 9.0 Fault finding 10 Valve block 11 Extra valve 12 El scheme 13 Oil scheme 6 8 9 9 9 9 10 10 10 11 11 11 12 12 12 12 13 13 14 15 15 15 17 17 17 18 18 18 18 19 20 22 23 24 25 26 27 28 28 29 30 30 30 31 31 32 32 33 33 33 34 34 34 35 35 36
Control system
1. Electronic 2. Control box 3. Display 4. Basic functions 5. Menu <Baler> 6. Menu 1 <Wrapper> 7. Menu 2 <Wrapper> 8. Menu settings 9. User settings 10. Display of faults/errors 11. Registration of failures 12. Auto sequence 13. Automatic function, change 14. Sensor failure 15. To by pass a sensor 16. Service indicator 17. Sensor Test 18. Zero setting of the control unit 19. Baler connection box 20. Sensor numbers at wrapper
Orkel
DECLARATION OF CONFORMITY
We,
Combi Balewrapper
serial number
....................................................................
that is covered by this declaration, are in conformity with the following standards, or other normative documents: NS-EN 292-1 (1991), NS-EN 292-2 (1991),NS-EN 704 (1999)
Jarl Gjnnes
Director
WARRANTY
Orkel AS warrants this machine against any manufacturing faults for a period of 12 months from the date of delivery to the customer (farmer). If there is no other agreement between customer and dealer, the warranty is limited to: 1. Value of the machine (done maintenance, in what condition) 2. Value of the damaged parts 3. On exchange of the goods, or 4. Making good defects in materials and/or workmanship, all the companys option. 5. The warranty scheme has to be returned to Orkel AS. Apart from the above, Orkel AS shall not in any circumstances be liable for any loss, damage or expense (including indirect and consequential loss or damage whether economic or otherwise) of any nature howsoever arising and including but not limited to any resulting directly or indirectly from negligent act or default of the company, its servants, agents or suppliers or from anything supplied or specified by the buyer or from improper maintenance/storage. Note: Warranty for normal wears and all moving parts and parts of rubber, tyres, hydraulic hoses, knives, chains and bearings are generally not accepted. Use of non-original spare parts or alteration of the machine without the knowledge of, or prior consent from the manufacturer will invalidate the above warranty. The warranty will be invalidated if the instructions in this manual are not followed.
Prior to delivery pre-delivery inspection carried out by the dealer. At time of delivery, instructions have been given by the dealer to the customer concerning the safe operation and maintenance of the machine. The above machine has been handed over to the customer with the users manual inclusive instructions concerning the safe operation and maintenance of the machine.
Prior to delivery pre-delivery inspection carried out by the dealer. At time of delivery, instructions have been given by the dealer to the customer concerning the safe operation and maintenance of the machine. The above machine has been handed over to the customer with the users manual inclusive instructions concerning the safe operation and maintenance of the machine. signature customer signature on behalf of the dealer
N.B. Dealer must not sign on behalf of customer. This form must be returned to Orkels sales company/importer within 14 days of delivery to authorise warranty.
Prior to delivery pre-delivery inspection carried out by the dealer. At time of delivery, instructions have been given by the dealer to the customer concerning the safe operation and maintenance of the machine. The above machine has been handed over to the customer with the users manual inclusive instructions concerning the safe operation and maintenance of the machine.
signature customer
N.B. Dealer must not sign on behalf of customer. This form must be returned to Orkels sales company/importer within 14 days of delivery to authorise warranty.
Dear Customer:
The Agronic bale wrapper is an efficient and economical long-term investment. When designing the machine, the manufacturer has taken into account all applications of state-of-the-art technology in the field of agriculture. The structure of the machine is based on results obtained from a long period of research and testing work under the many different operating conditions. Read this instruction book carefully before installing, using or servicing the machine. Pay particular attention to the safety instructions. This ensures that you will be able to use and service the machine in the most effective and safe way. Check that the instruction book corresponds to your machine . The instructions in this book must be followed.
In this book instructions relating to your safety are marked with the above sign. Take care that all users of the machine become familiar with these instructions and warnings. Note: Part copies, imitations and non genuine spares parts are not as well done as their appearance might suggest. The quality of the raw material cannot be discovered visually. Therefore use only genuine spare parts. Write down the exact model and serial number of the machine as well as the spare part supplier's contact information in the space below. These items of information speed up and ensure the receipt of correct spare parts. When ordering remember always to give the machine's model, serial number and year of manufacture. This information is found on the nameplate fixed on the machine. Remember that the information in this instruction book and the machine's guarantee do not cover eventual non genuine parts which have been installed at any time. Model: Serial number: Program version number: Year of manufacture: Spare part supplier: ___________ ___________ ___________ ___________ ___________
The machine has undergone tests and a test run at the factory. The flow adjustments of the machine's hydraulic system can, however, be easily changed. Therefore be specially careful always when using a machine after it has been unattended. The speed of the wrapping arm, for example, may be too high. The danger zone is always 5 m. As the film cutter contains a sharp knife, it must always be closed. e.g: if automatic operation is interrupted during wrapping and the machine is left unattended, the film cutter must be closed.
1.1
Hydraulics
A 1/2" hose is connected to the tractor's pressure coupling. A 3/4" hose is connected to the tractor's return coupling. To prevent unnecessary heating of the oil and machine failure, the oil must have an absolutely free return flow, not through valves. A high back-pressure on the return side disturbs, for example, the operation of lock valves. The bale wrapper requires an oil flow of about 1525 l/min [4 - 6.6 US gal/min]. Oil pressure at least 170 bar [2420 p.s.i.].
1.2
Electronics
NOTE: CONNECT ONLY TO A 12 V NEGATIVE EARTH SYSTEM. The brown lead is connected to the tractor's + terminal and the blue one to the frame. The supply voltage is 12 V. The machine does not work with a voltage below 10 V. Use with a voltage above 16 V is forbidden. The voltage must be taken directly from the battery. The cable supplied with the machine can be installed to the tractor as a fixed connection. The system must contain a 10 A fuse.
1.3
Control box
This device is placed in the cab and connected with the cable supplied. Make sure that the cable will not be twisted or crushed.
2.1
General
The control box receives its supply voltage via a cable, so normally it does not need a battery. In remote use it is operated by a 9 V battery. When the cable is not connected, the display does not operate either. The battery can be inserted by opening the two screws on the back. After removing the cover the battery can be seen. Use only high quality alkaline batteries. Remove the battery after finishing the season's work. The control box is watertight, but to ensure as long a lifetime as possible keep it always in a dry place indoors. Avoid dropping or causing mechanical damage to the control box.
2.2
Keypad
Up key increases the setting for wrapping revolutions. The reading is increased by one for each time it is depressed. The reading is stored automatically in the memory. The revolutions can be set between 960. In manual mode, the Up key is used to select desired function. Down key decreases the revolutions. Numbers below 9 can be set by pressing the key for 3 secs. In manual mode, the Down key is used to select desired function. Reset key can be used to reset the revolutions when necessary. By pressing the Reset and Total keys at the same time the bale counter is reset. Total key displays the number of bales. Start key: pressing this twice starts automatic operation. A prolonged press drops the bale. Stop key stops the operation immediately. Left arrow key opens bale chamber Right arrow key close bale chamber Man+ key stops automatic operation and runs the current operation in the forward, up or open directions. Man key stops the operation and runs the current operation in the backward, down or closed directions. The wrapping arm cannot rotate counter-clockwise (backwards), however. Up and Down keys: the closing time of the film cutter is adjusted by pressing these keys at the same time for about 3 sec. You will then see F5 on the left side of the display and the operating time in steps of 0.5 sec. on the right. The setting can be changed by pressing the Up or Down key. The setting is stored in the memory by pressing the Total key.
10
2.3
Automatic wrapping
1. The text redy must be shown on the display. 2. When bale is ready, push net button on balers controlbox. 3. The automatic loading and wrapping operation starts by pressing the Start key twice. The bale chamber open, bale goes to loading device. 4. When the bale activates the loading sensor, the machine loads the bale automatically. 5. The table goes to the mid-position. 6. Bale chamber close, the loading device goes to mid position. 7. Wrapping is started at a slow speed. 8. After one wrapping pulse and 2 sec. the film cutter opens for 0.5 sec. 9. The wrapping arm accelerates to full speed. 10. On the last but one revolution the wrapping arm slows down and the film cutter opens. 11. The film cutter is closed. The machine waits for a new command. 12. A prolonged press of the Start key will drop the bale, 13. After finished working cycle, the machine is always completely ready for a new bale.
2.4
Automatic operation can also be started at a point other than the starting point of the working cycle, if necessary e.g. after a power failure that has occurred during automatic operation. The mode is selected by pressing Man+ and Man keys at the same time until the display starts to blink. Using the Man+ or Man key, the desired mode of operation is located on the display. The selection is made by pressing the Start key twice. The redy mode can be selected at any time by pressing the Stop key for about 5 sec. Display Redy Open Load Wrap Tip Drop Explanation Machine ready for loading and wrapping Machine waits for a pulse from the loading sensor Operation starts from the loading mode Operation starts from the wrapping mode The machine waits for a command to drop bale Operation starts by bale dropping
2.5
The control box allows the functions to be controlled separately as follows. When pressing the Man+ or Man key, the F code corresponding to the function appears at the left side of the display. The code number indicates the function to be controlled. The function desired, or the F code, is selected using the Up and Down arrow keys. The control of the actual operation is carried out with the Man+ and Man keys. F code F2 F3 F5 F6 F7 Control Man Man+ Man Man+ Man Man+ Man Man+ Man Man+ Operation Lift fork down Lift fork up Table down Table up Film cutter closed Film cutter open Slow wrapping Fast wrapping, 3 sec. at slow speed then fast Chamber closing Chamber opening
11
2.6
Automatic operation can be interrupted using the Man+ and Man keys. If automatic operation is interrupted with the Man+ or Man key, they can be used to control the current operation immediately as defined above. To continue automatic operation, press the Start key twice.
2.7
Automatic operation stops if the conditions set in the machine's operating modes are not fulfilled, or they change during the operation. The machine then stops and is run to the Stop mode. An error code appears on the display. When pressing the Man+ or Man key, the operation is automatically set to control the function from whose sensor the error condition has emerged. Exception "Film", film broken; this can be corrected by pressing the Start key twice.
2.8
The display of control box also shows the state of the sensor for the selected function, if a sensor is fitted to the function. Display F2.A2 F2.A6 F3.A3 F3.A9 F6.A5 F7.A7 F7.A4 Explanation Loading fork in the mid-position Loading fork on the top Table in the mid-position Table has been run to the extreme position, down Wrapping arm has activated the sensor Bale chamber locked bale chamber totally open
2.9
During automatic operation the display shows the different phases of the working cycle. Display Redy Open Load Wrap Tip Drop Explanation Machine ready for wrapping Opens bale chamber Loading mode Wrapping mode The machine waits for a command to drop the bale or load another Bale dropping
12
2.10
Display Er.A2 Er.A3 Er.A4 Er.A5 Film Er.A7 Er.A8 Er.A9 Batt Stop S.t.o.p.
Error conditions
Explanation Lift fork not in the mid-position, or not regoniced A6 when goes down. Table not in the mid-position Bale chamber not open Wrapping arm does not activate the sensor Film has been broken during fast wrapping or wrapping speed too high. Bale chamber lock open Safety stop activated Table not down. Supply voltage too low Automatic operation interrupted using the Stop key Blinking, input A8 is not active, the wrapping arm's safety stop sensor activated. The points indicate this in other operating modes also.
The machine's hydraulic system is pressurised. Check hoses and couplings for damage. Replace any damaged parts immediately. When adjusting the machine's valves, keep away from the movement range of the wrapping arm. Crushing hazard! You must never go between the drawbar and the lift fork. Turn the valves carefully because, for example, the speed of the wrapping arm changes rapidly. Make yourself thoroughly familiar with anything you will be doing. Basic adjustments to the machine have been made at the factory. Before altering and checking any adjustments the hydraulic oil must have reached its normal operating temperature. The machine contains functions controlled by a pressure switch and it responds faster when the oil is cool. If, for example, the little arms would not open, or the lift fork or table would not lower automatically, it is not advisable to try to change any adjustments immediately. If the tractor's hydraulics supply decreases and the machine has been adjusted to use oil more than this, film overlap will not be as desired. On the other hand, the tractor's oil supply may exceed the amount adjusted because the excess oil returns directly to the tractor. If the tractor is fitted with a separate flow control valve, it is advisable to adjust it as close the actual oil requirement as possible.
13
3.1
Valve no. 1 regulates the total oil flow to the machine. When turning the valve clockwise, the amount of oil used by the machine decreases. Movements become slower.( should be about round open) Valve no. 2 regulates the ratio of the speed of rotation between the wrapping arm and the table. When turning the valve clockwise, the speed of the wrapping arm decreases and that of the table increases. .( should be about 1/2 round open) The wrapping arm's maximum permissible speed of rotation is 20 r/min . This adjustment also determines the highest speeds for all other operations because the overlap must always be 5055 %. When adjusting the overlap it may be necessary to adjust both of the above valves. Make the following adjustments to the wrapper: 1. The tractor's hydraulics oil must have reached its operating temperature. 2. Adjust the tractor engine speed as desired for the wrapping revolutions. Take into account that during wrapping the tractor can be used at higher revolutions as well because the excess oil returns directly to the tractor. On the other hand, film overlap will change if the amount of oil supplied by the tractor drops below the set value. 3. Open valve no.1 . ( round.) 4. Adjust the wrapper arm speed using valve no. 2. ( round first) When opening more, arm goes faster. Using valve no. 1 adjust the overlap. 5. Increase the number of revolutions for the tractor engine. If the speed of the table increases, valve no. 1 has been opened too much. It must therefore be turned toward the closed position and the valve overlap adjusted correctly. 6. The speed for slow wrapping is adjusted using valve no. 10 if necessary. The adjusting screw has been secured by a nut. The adjustment is made using an Allen key. The slow wrapping speed increases when the oil is hot so observe the machine and, if necessary, adjust the slow speed again. The slow wrapping speed must be correct for the operation of the timing of the film cutter. 7. The adjustment of the film cutter speed is made using valve no. 5; the speed decreases by turning clockwise. If the speed is too high, the film may break when the cutter is only closing. 8. The adjustment of unloading speed is made using no. 3. The speed decreases by turning clockwise. If the speed is too high, the bale can drop down when table goes middle.
14
During wrapping the side tipper is located in a horizontal position behind the bale wrapper. When the table is being lowered, it is lowered to the ground. When the table is being raised, it rises up. Take care that the wrapping arm will not hit the side tipper during wrapping. When using the side tipper, take into account that the bale falls to the right when viewed from behind. Make sure that there is nobody behind or beside the machine. If a bale turns too quickly, it is possible that it rolls further onto the other side and causes a dangerous situation. The machine must not move when dropping a bale.
Operating principle
When dropping a bale, it rolls on the side tipper under its own weight. Because of the design of the device, the bale turns on its end. The side tipper cannot be adjusted but the following items affect its operation: Adjustment of the ground clearance. In the higher position the device works more efficiently. The lowering speed of the table. Valve no. 3 The faster the speed the more quickly the bale rolls down. When the table is in the extreme downward position, the belts must be tight. Symmetrical bales of uniform quality turn best. Since the table is down for 2 sec., you may drive forward if necessary, thus avoiding the bale being torn in the corner of the side tipper.
15
6. When using a 500 mm film in the 750 mm stretcher, the stretcher must be fitted with an adapter. The adapter tube is fitted inside the film roll.
16
7.0 Operation
The operation of the bale wrapper is automatic. Study and understand fully all the functions of the machine before use. After the START command the operation continues automatically. The machine can be stopped when necessary by using the STOP command on the control box, by switching off the tractor's directional valve or by pressing the EMERGENCY OFF button down. Always make sure that there is nobody in the working range of the machine. As the film cutter contains a sharp knife, it must always be closed. Take care when selecting the bale dropping point, the bale might roll a long way on a sloping ground.
7.1
General
Be careful at every stage of the bale making. Try to prevent any impurities from entering the feed. Make as tight and uniform bales as possible. Film overlap must be 50 %. Wrap 2+2+2 layers. Use only high-quality wrapping film. If bales must be moved after wrapping, do it as soon as possible. Familiarize yourself with the user instructions supplied with the wrapping film package. Consult advisory organizations for instructions regarding suitable mowing time, moisture content and storing.
17
7.2
The lift fork must be in the middle or down (F2A2) and the table up. Check that there is wrapping film in the stretcher and that the end of the film is in the cutter. Switch on the oil flow and supply voltage to the machine. When switching on power to the control box, the following texts will scroll on the display: AGRONIC, the program's VERSION NUMBER and finally REDY. If the machine does not fulfil the conditions set for the REDY mode, an error message will appear on the display. Check the number of revolutions and film overlap. A 120 cm bale requires about 13 revolutions for a wrapping of six layers (75 cm film,). Always ensure that the number of revolutions will be adequate when wrapping the first bale. If the tractor's oil supply drops below the set amount, this will first slow down the rotation of the table and the film overlap will change. The bale must have net first. By pressing the Start key twice the chamber open. When the bale activates the loading sensor, loading starts automatically. Driving can be continued immediately when chamber is closed and ful alarm is of. Take into account the unevenness of the ground and reduce the forward speed if and as necessary. The bale wrapper continues to operate automatically stage by stage. When a bale has been wrapped, the text reading TIP appears on the display. The wrapper then waits for a command to drop the bale. A prolonged press of the Start key will drop the bale.
7.3
When one roll runs out, the ER.FL message appears on the display. Automatic operation starts again by pressing the Start key twice. In this case only every second of the wrapping pulses is read so the correct amount of film is applied. Film overlap is not the same as with two rolls, however. When both rolls have run out, the machine stops, and the steady error message FILM is shown on the display.
7.4
The safety stop (option) stops all machine functions. Manual control does not operate, either. This is indicated by the four lighted points at the bottom of the display. The switches of the safety stop must be released by hand. The machine can then be controlled in the normal manner.
7.5
Transport
Remove the film roll from the stretcher. Switch off the oil flow.
18
8.0 Maintenance
Always before cleaning and servicing: Switch off the supply voltage and the oil flow. Stop the tractor's engine. Do not go under raised machine parts which are not safely supported.
Daily:
Check the condition of the hydraulics hoses and couplings. Check the supply voltage cable and the control box cable. Clean the film cutter.
Every 25 hours:
Lubricate all slide bearings with high-quality grease. Note: to be able to lubricate the upper part of the bogie centre axle, the machine must be jacked up. Lubricate the drive chain for the table and wrapping arm.
19
If you search for an electricity fault, stop the tractor engine before fault finding. If this is not possible, keep out of the machine's movement range. The lift fork may drop even if the hydraulics were not switched on. Be careful with an open film cutter. If the bale wrapper does not operate correctly, always check first: supply voltage, cables, tractor's directional valve, quick couplings and pressure filter. If the supply voltage is not received directly from the battery, the voltage may fluctuate so quickly that the control box is not fast enough to give an error message. The processor card and the control box cannot be repaired, they must be replaced with new ones.
The ill. shows relevant gap for sensors in general. For film control sensors the gap must be less, apx. 1 mm because of quick rotation.
20
Machine jerks
- Defective quick couplings or oil supply from the tractor or fluctuating supply voltage. Check supply voltage cables, quick couplings, oil level, pressure filter.
21
10 Valve block
Slow wrapping valve 10 Wrapper arm speed valve 2 Chamber Loading Film cutter Table
22
11 Extra valve
23
12 El scheme
Safety stop Chamber lock Loading not top Wrapper arm Chamber open Table middle
24
13 Oil scheme
MOTOR
BRAKE
10
SLOW SPEED
TABLE
FILM HOLDERS
LIFT UP
CHAMBER
TABLE MOTOR
FILM HOLDERS SPEED ADJUST. VALVES FILM HOLDERS LOCK VALVE
CHAMBER-LOCK VALVE
15
25
Control system
Orkel GP 1250 Agronic Bale Wrapper
(on GP 1250 machines with serial no. higher than 2210045) Type: MK3/MK2
26
1. Electronic
ATTENTION! Use only with 12 V (minus earth leaded system) Connect the red cable to the plus-pole and the black one to the minus-pole of the tractor battery. The operating voltage is 12 V and the system doesnt work if the voltage drops under 10 V. On the other side, the voltage shall not exceed 16 V. Ensure a stable power supply. The delivered cable can be connected to the tractor battery constantly. The system has to be guarded with a 35 A fuse. 1. 2. 3. 4. 5. Place the control box with the magnets in the tractor cabin. Use the steel plate as a basis. The cable from the baler does the power supply. The smaller cable is doing the data communication. Ensure that the cables will not be squeezed or rub at any object. When disconnecting the control box from the tractor always keep it at a dry place. Protect the end of the cables from moisture and wind.
ATTENTION! The motor of the net tying system can start as well without connected control box. Always disconnect the power supply cable from the tractor during service or reparation on the machine.
27
2. Control box
n
This area of the display shows: Information about status of the system and function, together with different activities and adjustments.
Connection for the signal cable from the baler. Digital BUSsignal for all functions.
The text in this area and up to the right, shows which function the nearest key has. STOP or ESC The yellow-orange key has the functions Stop and Esc. After Stop you can chose choose to continue again.
Choose your language right after connecting the control box to the power supply. The chosen language will be stored. The display is changing to sleep modus after an inactive period of time. Touching a key restarts the display again. Ensure that the control box always is under dry conditions. Avoid hits on the control box.
3. Display
Choose your language right after connecting the control box to the power supply. The chosen language will be stored. The commands are given by touching the respective key on the display of the control box. You dont have to touch hard. An acoustic signal is confirms the command. The meaning of the touching area is changing from menu to menu. But the yellow area always means the same. Stop or Esc. This key area has to be activated to stop automatic functions, to go back to the basic menu or to leave the menu. The first display shows the basic menu. Preceding you will come to the adjustments. By Reset the automatic function will be set into the start position. It also asks, are you sure? Yes or No. The automatic function can be started in two ways. Either by touching the Start key or by starting the PTO shaft. Then, the automatic system is prepared for the first bale.
28
4. Basic functions
After touching the Start key, the display shows following: - Date and Time - Working hours. The number of working hours is determined by measuring the rotation speed of the PTO shaft. - Name of customer or field description. - Status for the chopping knives, in (cutting) or out (not cutting). - Adjustments for the baler functions. - Rotation speed of the PTO, display is showing 0 rpm. - Status of greasing system. The greasing system starts automatically when PTO exceeds 300 rpm and opposite. - Status of acid adding system. The acid adding system starts automatically when PTO exceeds 300 rpm and opposite. The acid adding system will be stopped when net tying is starting. The addition of acid will be restarted when the Stop signal disappears on the display. That means the bale chamber is closed again and you can proceed baling. The addition of the acid can be stopped when touching the key. The text near the key is telling the function of the system. Because of safety reasons the acid system cant start automatically, but manually. Loading AUTO or MANU. If auto, then baler opens automatically after successful net tying. If manu, driver has to push load manu button after net tying, after that, the rest of the process is done automatically. Independent if the wrapper control system is put into manual or automatic, the working process will continue automatically in both cases after wrapping. It is possible to adjust the point of time for net tying (Delay full chamber to net start). After receiving the signal for full chamber, the system starts the net tying after waiting a moment. This moment/delay can be adjusted between 1 and 10 sec. Thats the time the driver has to stop the tractor, before the net tying starts automatically. Is the net tying set on automatic, and you wish to start the tying earlier, you have to choose the menu to change the adjustments. You can use the same principle when wishing to have the bale longer in the baling chamber. But you have to be aware, that you stress the driveline of the baler over the average. When choosing no net tying, the chamber opens automatically, without net on the bale. The yellow key stops all automatic function immediately. The automatic system remembers where the interruption was and can proceed at the same place after touching the start key. EXT. OUT. With this button you can put external power output on and off. Max load is 8,5A and 12V. This output cuts off when machine goes into sleep mode after 10 minutes, if machine is not in action.
29
5. Menu <Baler>
Touch Go on to come to the menu <Baler>. Here you can adjust the numbers of rotations for the wrapper arm. Is the overlapping of the film correct, the right number should be 12 or 13. This information is a recommendation and is valid only for 750 mm film and 6 layers. The adjusted number will be stored when leaving the menu. Baling without wrapping. Set the number of wrapper arm rotations to 0. Right after the bale is loaded on the wrapper table, you will see the command on the display to unload the bale. The chamber can be closed and opened with the two keys on the left side of the display. Is the chamber closed the function has some seconds delay. The display shows when the chamber is opened, but not the angle.
6. Menu 1 <Wrapper>
Touch the key for Wrapper 1 for coming into the first part of the wrapper menu. The name for the actual menu is in a frame. By using up and down, you can move the lifting arm. The display shows the position of the lifting arm (bottom middle top). The lifting arm stops where you let loose the key. In addition the system shows you if there is a bale on the lifting arm or not. For the wrapper table you have the same principle like for the lifting arm. The only difference is that the display doesnt show when in top position.
7. Menu 2 <Wrapper>
Touch the key for Wrapper 2 for coming into the corresponding menu. The wrapper arms are going into start position automatically. At the same time, the film holders will be closed. We recommend tying up the film ends crosswise under transport. When starting wrapping, the automatic system requires both arms in start position (in contact with both sensors). Wrapping slow - When touching the key, the wrapper arms are rotating slowly as long as you hold the key. The wrapper table doesnt rotate. Wrapping fast - When touching the key, wrapping will be done slowly in two minutes. After that wrapping will continue with high speed as long as you hold the key. Wrapping AUTO - When touching the key, the automatic wrapping is starting with the determined numbers of rotations. With the yellow key you can go back in the menu and unload the baler later. You can delete the number of bales together with the customer. It is not possible to take care of the name of the customer when deleting the number of bales and it is not possible to delete the total number of bales. With the up and down keys you can change from one storage place to another. The star shows the actual position. With the activating key you get into the chosen storage place to make adjustments. Put in the data as the name of the customer by this way. - The letter function will be activated by the key sign. - ABC scrolls the alphabet forward, ZXY backward. - With the arrow key you come to the next letter. - With erase you delete letters or information. - With escape you store the given information and go out of the menu. With the yellow key you leave the menu without storing.
30
8. Menu settings
With the up and down menu, you go to the position to make changes. With the key change you can change the actual settings. The changes will be stored after leaving the menu. The net role control registers, if the net role is rotating. Standard is on. The wrapping control registers, if there is film in both pre-stretchers. Standard is on. If it should be necessary to loan a sensor at another place it is possible to use one of the wrapping control sensors. In this case you have to deactivate the wrapping control function (off). Net tying. Manual or automatic start. This setting can be changed at all times, as well in the wrapper menu. Time setting chamber sensor. Rear door sensor response time is the time how long the chamber sensor has to be activated before the system accepts full chamber signal. Delay for opening of the film holder/knife. The film holder releases the film ends at the start of the wrapper process. 1 impulse = (1/2 rotations) + delay. The delay time has to be changed if the film ends are released to the wrong time. The delay has to be longer if the film is released too early, or opposite. The rotation speed of the wrapper (valve no. 10) can as well influence the necessary delay time. How good the film is fixed during cutting depends on a time setting. This time can be changed as well. The reaction time for opening the chamber can be adjusted. A too short time can lead to that the bale doesnt fall on the lifting arm. A too long time makes the whole process unnecessary long. Loading AUTO; leads to immediate loading of the bale when bale has net. MANU; driver has to push button to load.
9. User settings
In this menu the actual program version is shown, both in the remote unit and in the control unit. Her you can adjust the brightness of the display. If you wish, you can by using the key neg/pos invert the display (black becomes white and opposite). Set the clock by using the set clock time key.
31
32
33
34
35
Emergency stop A8
Volum valve 2
36