Professional Documents
Culture Documents
3/13/2011
H-bridge
March 2011
2
4 5
5 6
3)
Components 3.1 PWM 3.2 Inverted signal 3.3 Optocoupler 3.4 Mosfet 3.5 Dead time control 3.6 Isolated DC/DC Converter Circuit diagrams Conclusion
8 8 9 10 11 11 12 13 16
4) 5)
1) Introduction
The main aim of this experiment is to control a motor with a dc voltage signal by manipulating the duty cycle of the PWM signal in order to turn it left or right.The eficency of the circuit should be high. This has to be done with a half H-bridge. The half H-bridge block diagram, divied in subsystems is presented below (Fig 1.1).
PWM Generator
Driver / Isolation
Bridge
Load
Figure 1.1 H-bridge block diagram Another aim of the h-bridge carrousel project was to develop a printed circuit board(PCB) for the Driver part, including the isolation.
2) Theory
In this part of the report it will be explained the theory behind the H-bridge design and control.
Figure 2.1 PWM Generator Output stays high as long as the command is greater than the carrier
Figure 2.3 PWM Control and duty cycle The output of a PWM amplifier is either zero or tied to the supply voltage, holding losses to a minimum. As the duty cycle (Fig 2.3) changes to deliver more or less power, efficiency remains essentially constant.
2.2) H-bridge
An H bridge (Fig 2.4) is an electronic circuit which enables a voltage to be applied across a load in either direction. These circuits are often used in robotics and other applications to allow DC motors to run forwards and backwards. H bridges are available as integrated circuits, or can be built from discrete components.
The H-bridge arrangement is generally used to reverse the polarity of the motor, but can also be used to 'brake' the motor, where the motor comes to a sudden stop, as the motor's terminals are shorted, or to let the motor 'free run' to a stop, as the motor is effectively disconnected from the circuit. The following table (Fig 2.5) summarizes operation, with S1-S4 corresponding to the diagram above.
S1 S2 S3 S4 Result
Motor brakes
Motor brakes
Half H-bridge:
Figure 2.6 Half H-bridge circuit In half-H bridge switches S3 and S4 are replaced by two voltage sources. The switches S1(Q1) and S2(Q2) are controlled by the PWM that we initially made and an inverted PWM signal, here we offer the PWM signal to the mosfets which will be 50% duty cycle the average value of the voltage across load 0 volts are. So this will stop the load. If you have more than 50% duty cycle then the voltage across the load is positive. Then the motor runs in certain direction. If the duty cycle its under 50% the voltage across the load is negative and the motor turns the other direction. The duty cycle is controlled via PWM and is used to adjust the motor clockwise and counter clockwise.
3)
Components
In this chapter there will be analysed the main components used in our circuit. The main componets used are: a) PWM power control chip: SG3524N b) Inverter c) Optocoupler d) Dead time control e) Mosftes f) Isolated DC/DC Converter
Figure 3.1 Functional Diagram SG3524N PWM controller The SG2524 (Fig 3.1) incorporate all the functions required in the construction of a regulating power supply, inverter, or switching regulator on a single chip. We use the SG2524 to control the PWM signal. The frequency of the PWM can be controlled with the help of a resistor (Rt) and capacitor(Ct) (Figure 3.2).
Practical values of CT fall between 0.001 F and 0.1 F. Practical values of RT fall between 1.8 k and 100 k. This results in a frequency range typically from 130 Hz to 722 kHz. The PWM control circuit is present in figure (Fig 3.3) below:
Any general purpose low power NPN transistor can be used. For general use RB = 10kohm and RC = 1kohm, then the inverter output can be connected to a device with an input impedance (resistance) of at least 10kohm such as a logic IC or a 555 timer.
3.3) Optocoupler:6N135
Figure 3.5 Functional Diagram 6N135 Optocoupler These diode-transistor optocouplers (Fig 3.5) use an insulating layer between a LED and an integrated photo detector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output-transistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base- collector capacitance. For this project, we chose two optocouplers (Fig 3.6) one pin is for the normal signal and the other for the inverted signal. At the input Number two on the pin of the IC is placed a 750 resistor in order to protect the diode against high current. At the output of the IC is placed a 4k resistor for a better output signal at high frequencys The output of the optocoupler is going at the gate of the mosfet.
10
11
Figure 3.9 DC/DC converter Two Isolated DC/DC converters (NKE1215sc and NKE1212SC)(Fig3.9) are used in order to provide an high voltage at the mosfet gate. This voltage is used to for turning on and of the switches. The DC/DC isolator is used to protect the driver circuit against high voltage coming from the H-bridge load(E.G. Motor).
12
4)
Circuit diagrams
a) Final circuit
13
b) Driver Circuit
Figure 4.4 Driver Board Input and output Figure 4.4 explains how the Driver board is connected with the rest of H-bridge components. At PW input is connected the output of the PWM generator. There is no need for an inverter. The inverter is already implemented on the Driver board Its necessary to beimplement an Dead time control circuit before the PW input. It can be used any pin from PW input, because the pins are connected together. Upper output it will be connected at the GATE pin of the MOSFET from the upper side, GND it will be connected at the SOURCE pin of the upper MOSFET. LOWER output it will be connected at the GATE pin of the MOSFET from the lower side, GND it will be connected at the SOURCE pin of the lower MOSFET.
14
15
5)
Conclusion
H-bridge is a nice subject of Carousel. Over a week, we gained more insight about the performance which is how to control the motor of H-bridge. Most of parts are worked properly. Beside that the theory is easy to understand but we still have some small problems during the simulation. Our Mosfets got over heated in normal operation. That means there is a partial short circuit between mosftes. This is due to the fact that we implement the dead time control just for the non-inverted signal. To solve the problem is needed to be implemented a better dead time control. But in reset everything is working proper.
16