You are on page 1of 4

ES-F-LF880V

SPECIFICATION SHEET

LEAD FREE*

MasterSeries LF880V
Reduced Pressure Zone Prevention Assemblies
Size: 212" - 10" (65mm - 250mm)
The FEBCO MasterSeries LF880V Reduced Pressure Zone Assembly is specifically designed to protect against possible backpressure and backsiphonage conditions for high hazard [i.e., toxic] application in accordance with Local Governing Water Utility Code. This Backflow Assembly is primarily used on potable drinking water systems where Local Governing Code mandates protection from non-potable quality water being pumped or siphoned back into the potable water system. The LF880V features Lead Free* construction to comply with low lead installation requirements. The Lead Free* Reduced Pressure Zone Assemblies shall comply with state codes and standards, where applicable, requiring reduced lead content.

Features
Inline Serviceable Assembly Horizontal N-Pattern Installations Vertical-Up Z-Pattern Installations No Special Tools Required for Servicing Captured Modular Spring Assembly Reversible & Replaceable Discs Field Replaceable Seats Ductile Iron Valve Body Design Stainless Steel Check Components Modular Pressure Differential Relief Valve Repairable Pressure Differential Relief Valve Clapper Check Assembly Captured O-ring Design

MODEL 880V REDUCED PRESSURE ZONE ASSEMBLY (Shown in standard orientation)

Specifications
The FEBCO MasterSeries LF880V Reduced Pressure Zone Assembly shall be installed on the potable water supply and at each point of cross-connection to protect against possible backpressure and backsiphonage conditions for high hazard [i.e., toxic] applications. The assembly shall consist of a main line valve body composed of a pressure differential relief valve located in a zone between two (2) independently acting approved clapper style check modules with replaceable seats and disc rubbers. Servicing of the pressure differential relief valve and both check modules does not require any special tools; both check modules are accessed through independently top entry covers. This assembly shall be fitted with AWWA Compliant inlet/outlet resilient seated shutoff valves; when used on a Fire-Sprinkler application, the assembly shall be fitted with approved UL/ FM inlet/outlet resilient seated shutoff valves and contain four (4) properly located resilient seated test cocks as specified by AWWA Standard C511. Flow and pressure loss performance parameters shall meet the requirements of AWWA Standard C511.

IMPORTANT: INQUIRE WITH GOVERNING AUTHORITIES FOR LOCAL INSTALLATION REQUIREMENTS


* The wetted surface of this product contacted by consumable water contains less than one quarter of one percent (0.25%) of lead by weight.

Job Name Contractor Job Location Approval Engineer Contractors P .O. No.

Approval Representative
FEBCO product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact FEBCO. FEBCO reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on FEBCO products previously or subsequently sold.

Options - Suffix
OSY: UL/FM Approved OS&Y Gate Valves (ANSI/AWWA C515 Compliant) NRS: Non-Rising Stem Gate Valves (ANSI/AWWA C509 Compliant) LG : Less Shut-off valves; This is NOT an APPROVED ASSEMBLY Example Ordering Description: 4 LF880V-OSY - Valve Assembly fitted with OS&Y Shutoff Valves

Approvals Standards:
A  pproved by the Foundation for Cross-Connection Control and Hydraulic Research at The University of Southern California [FCCCHR-USC] ASSE 1013 Listed **UL Classified [US & Canada] **FM Approved IAPMO/cUPC AWWA Standard C511 Compliant E  nd Connections: Compliant to ASME B16.1 Class 125 & AWWA Class D Flange **Assembly configured with UL/FM Approved OS&Y RW Gate Valves. Less gate valve assemblies are not UL/FM approved configurations. ** 1013 B64.4 **

Available Components
Wye Strainer: FDA Approved (ASME B16.1 Class 125 & AWWA Class D Flange) Series 611 Valve Setter:  MJ x MJ - Mechanical Joint x Mechanical Joint (AWWA C111/A21.11) MJ x FL - Mechanical Joint x Flange  (AWWA C111/A21.11; ASME B16.1 Class 125/ AWWA Class D Flange) FL x FL Flange x Flange (ASME B16.1 Class 125 & AWWA Class D Flange)

Materials
Below is a general materials list of the Model LF880V. All assemblies size 212 through 10 is similar in materials and construction. Please contact your local FEBCO Representative if you require further information. Main Valve Body: Ductile iron Grade 65-45-12 Relief Valve Body: Ductile iron Grade 65-45-12 Coating: Shutoff Valves: Check Seats: Disc Holder: Spring: Clamp: Fusion epoxy coated internal and external AWWA C550-90   RS resilient wedge gate valve AWWA C509 (Standard) N OSY resilient wedge gate valve AWWA C515 (UL/FM) Stainless Steel Stainless Steel Stainless Steel AWWA C606

Assembly Flow Orientation:


Horizontal (N-Pattern 212 10) - Approved by FCCCHR-USC, ASSE, cULus, FM, IAPMO/cUPC Vertical Up (Z-Pattern 212 10) - Approved by FCCCHR-USC, ASSE, cULus, FM, IAPMO/cUPC

Pressure - Temperature
Max. Working Pressure: Min. Working Pressure: 175psi (12.1 bar) 20psi (1.4 bar) Hydrostatic Test Pressure: 350psi (24.1 bar) Hydrostatic Safety Pressure: 700psi (48.3 bar) Temperature Range: 33F - 140F (0.5C- 60C) Continuous

Elastomer Disc: Silicone

Test Cock #3 #3 Test Cock

TestCock Cock #4 Test FirstSpring Spring First Assembly Assembly FirstCheck Check First Assembly Assembly

Second Check Second Check Assembly Assembly Second Spring Second Spring Assembly Assembly

TestCock Cock #2 #2 Test

Isolation Isolation Shut-off #1 Shutoff #2

TestCock Cock #1 #1 Test

Relief Valve Relief Valve Assembly Assembly

Isolation Isolation Shut-off #2 Shutoff

Dimensions Weights
Size: 212" - 10" (65 - 80mm) Below are the nominal dimensions and physical weights for the Model LF880V size 212 through 10 . Allowances must be made for normal manufacturing tolerances. Please visit our website to download a copy of this products installation instructions, or contact your local FEBCO Representative for more information. Model LF880V Model LF880V Standard Orientation Vertical Orientation (N-Pattern) (Z-Pattern)

E D E D G H C A F

I C B A

Gate Valve Side View

Relief Valve Detail Relief shipped on right side (shown) field reversible to left side.

K* L**
SIZE (DN) A in. 212 3 4 6 8 10 mm 65 80 100 150 200 250 in. 2512 2534 2778 32
14

C L

J
DIMENSIONS

4 1516

3 12
WEIGHT***

B mm 654 654 708 819 953 1080 in. 1212 1212 14 16 1812 21 mm 318 318 356 406 470 533 in. 614 614 7 8 914 10

C mm 159 159 178 203 235 254 in. 2414 2414 2634 32
14

D mm 616 629 680 819 324 1035 in. 1658 1658 1734 21
58

E mm 422 422 451 548 632 699 in. 1358 1418 1512 18 24
58

F mm 346 359 394 473 527 610 in. 2714 2814 31 37 48


14

G mm 692 718 787 946 1054 1219 in. 512 512 6 7


12

H mm 140 140 152 191 222 248 in. 714 714 714 9
12

I mm 184 184 184 241 260 292 in. 312 334 412 5 8
12

J mm 89 95 114 140 172 203 in. 1258 1278 1438 18


78

K* mm 321 327 365 479 597 699 in. 1638 2214 2314 30 48
18

L** mm 416 565 591 765 959 1219

NRS lbs. 221 247 344 517 808 1306 kg. 100 112 156 235 366 592

OSY lbs. 225 251 356 537 836 1344 kg. 102 114 162 244 379 610

3712 4212

3638 4034

2478 2712

2034

4112

834 934

1014 1112

634

2312 2712

3734

Notes: * Indicates nominal dimensions with NRS Gate Valves ** Indicates nominal dimensions with OSY Gate Valves (Full Open Position) *** Indicates weight of complete Backflow Assemblies with specified Gate Valves The gap drain is not designed to catch the maximum discharge possible from the relief valve. The installation of the FEBCO air gap with the drain line terminating above a floor drain will handle any normal discharge or nuisance spitting through the relief valve. However, floor drain size may need to be designed to prevent water damage caused by a catastrophic failure condition. Do not reduce the size of the drain line from the air gap fitting.

Performance
Flow capacity chart identifies valve performance based upon rated water Velocity up to 20fps  Maximum service flow rate is determined by maximum rated Velocity of 7.5fps.  AWWA Manual M-22 [Appendix C] recommends that the maximum water Velocity in the services be not more than 10fps.  UL flow rate is determined by typically rated Velocity of 15 feet/sec.
Pipe Support (furnished by customer) for valve weight only.

Standard Orientation (N-Pattern) Flow Curve N


kPa psi 110 97 83 69 55 41 28 14 16 14 12 10 8 6 4 2 Headloss (psi)

Vertical Orientation (Z-Pattern) Flow Curve Z


6" (150mm)

212" (65mm)
Headloss (psi)

kPa psi

N Z

0 50 100 150 200 250 300 gpm 0 190 380 570 760 950 1140 lpm

124 110 97 83 69 55 41 28

18 18 16 16 N 14 14 12 12 10 10 8 8 Z 6 6 4 4 0 200 400 600 800 1000 1200 1400 gpm 0 200 400 600 800 1000 1200 1400 0 760 1520 2280 3040 3800 4540 5300 lpm

kPa psi 124 110 97 83 69 55 41 28 Headloss (psi)

18 Z 16 14 12 N 10 8 6 4 0 50 100 150 200 250 300 350 400 450 gpm 0 190 380 570 760 950 1140 1330 1520 1710 lpm

3" (80mm)

kPa psi 138 124 110 97 83 69 55 41 28 Headloss (psi)

20 20 Z 18 18 16 16 14 14 12 N 12 10 10 8 8 6 6 4 4 0 500 1000 1500 2000 2500 3000 gpm 0 1900 3800 5680 7560 9500 11350 lpm 0 500 1000 1500 2000 2500 3000

8" (200mm)

kPa psi 124 110 97 83 69 55 41 28 14

18 16 Z 14 N 12 10 8 6 4 2 0 100 200 300 400 500 600 700 gpm 0 380 760 1140 1520 1900 2280 2660 lpm

4" (100mm)

kPa psi 138 20 110 16 83 12 55 8 28 4 0 0 Headloss (psi)

10" (250mm)

Headloss (psi)

Z N

0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 gpm 0 1900 3800 5680 7560 9500 11350 13250 15140 17030 18900 lpm

Z-Vertical orientation N-Standard orientation

The 6" and 10" flow curves (N-standard orientation) include the FEBCO valve setter model 611.

A Watts Water Technologies Company

USA: Fresno, CA Tel: (559) 441-5300 Fax: (559) 441-5301 www.FEBCOonline.com Canada: Burlington, ON Tel: (905) 332-4090 Fax: (905) 332-7068 www.FEBCOonline.ca

ES-F-LF880V 1206

2012 FEBCO

You might also like