You are on page 1of 8

June 2004

JANUARY 2010

Popular Spare Parts For ML7 Lathes


History
The ML7 lathe was launched in August 1946, the basic bench lathe retailing at 34.00. The ML7 was so successful that it saw the immediate demise of its predecessors the ML2 and ML4. The Myford M type, a Myford version of the Drummond M type, cost 42.00 and production of this was discontinued in 1949. Over its 33 years production run, the ML7 stood the test of time remarkably well. Whilst there were numerous minor changes, the number of major design changes were very few and these are listed below. In July, 1969, commencing with serial No K90494, a cast lug was incorporated into the headstock. The lug is situated just behind the spindle nose and its initial purpose was to act as an anchor point for the optional lever operated collet attachment. In later years the same point would be used as a pivot point for the chuck guard. In May, 1972, from serial No K107657, the existing carriage was converted from the narrow guide to the wide guide principle. On the earlier machines the saddle located across the front two shears and on later models across the full width of the bed, the 5/8 diameter leadscrew and die cast apron were retained. From serial No K108718, the cross slides were fitted with 5mm pitch self locking adjusting screws. April, 1973, saw the introduction of the new bed from serial No K111727. The re-design was necessary to accommodate the power cross feed apron on the Super 7 lathe. At the same time the specification of the ML7 was upgraded to incorporate the diameter leadscrew and cast iron apron as used on the pre-power cross feed Super 7s The last machine, serial No K140848, left the fitting lines on the 31st January 1979. It should be noted that long bed ML7 lathes were always fitted with diameter leadscrews and the saddles, cross slides and top slides were the same as used on the pre-power cross feed Super 7 lathes. Please Note: When ordering, kindly state the serial number and prefix letter of your lathe. On earlier machines up to serial No K111727 this will be found on the rear shear of the lathe bed, at the tailstock end of the machine. On later machines after serial No K111727, this will be found on the front of the lathe bed, to the left-hand side of the rack.

Popular Spare Parts For ML7 Lathes


Headstock Section:
Part Number Description Price Excl. VAT Price Incl. VAT

65174 11261 70/1230 70/1205 70/1206 70/1203 70/1204

A8122 A8120 A8121 70/1226 70/1227 11163 70/1218 100405 70/1219 A4728 70/1220 80001 70/1234/2 70020 33/072 73044 70/1246 11266 70/1242 70/1241 70/1232/2 70/1249 70/1129 70/1137

Sight feed lubricator Fibre washer Spindle (original specification) - no longer available Spindle bearing - front - white metal - no longer available Spindle bearing - rear - white metal - no longer available Laminated shim - front bearing Laminated shim - rear bearing Note: We are no longer able to purchase further supplies of the original white metal bearings at sensible prices. This has necessitated the supply of the kit detailed below as a direct replacement and in terms of cost it is approximately half the price of what a new set of bearings would be. ML7 Headstock Spindle and Bearing Kit: Hardened spindle Spindle bearing - front - bronze, complete with shims Spindle bearing - rear - bronze, complete with shims Price for Headstock Spindle with Bearings complete 65T Backgear assembly, includes driving key etc. Backgear key Special allen key, for use with above backgear key Backgear cluster assembly 21/56T gear Socket countersunk screw (2BA x ) Plunger Spring Screwed bush Knob Vee cone pulley assembly Vee belt - headstock Pack of 10 x 65000 2BA oil nipples Thrust bearing 25T Gear Grubscrew (2BA x 3/16) - formerly MY2820 20T Tumbler gear 18T Tumbler gear Tumbler sleeve gear Soft centre - 2MT 6.3/4 dia Standard faceplate Catchplate with 11291 drive peg

11.54 0.14

13.56 0.16

3.58 3.58

4.21 4.21

195.20

229.36

297.75 48.78 9.96 2.42 22.44 0.11 7.26 0.16 1.12 5.78 72.54 9.44 6.65 49.22 8.64 0.39 10.15 10.15 41.02 8.96 46.43 23.49

349.86 57.32 11.70 2.84 26.37 0.13 8.53 0.19 1.32 6.79 85.23 11.09 7.81 57.83 10.15 0.46 11.93 11.93 48.20 10.53 54.56 27.60

Popular Spare Parts For ML7 Lathes


Countershaft and Motorising Section:
Part Number Description Price Excl. VAT Price Incl. VAT

70/1619/2 70003 70/1626/6 A1973 A1832 A1227 A2834/1 33/072 70/1624 70/1625 100315 80003 A1851/1 A1853/1 70025

Countershaft Woodruff Vee cone pulley assembly Thrust washer Countershaft pulley Hard rubber bush Oilite bush Pack of 10 x 65000 2BA oil nipples Knob Spring clip Hexagon head set screw (1/4 BSF x 5/8) Knob (1.1/4 dia x 5/16 BSW) Motor pulley - 5/8 bore 1.7/8 dia Motor pulley - 5/8 bore 2.1/2 dia Vee belt - motor drive

24.85 0.63 35.36 0.13 20.79 6.57 3.05 6.65 5.05 1.70 0.44 4.08 12.68 21.82 7.38

29.20 0.74 41.55 0.15 24.43 7.72 3.58 7.81 5.93 2.00 0.52 4.79 14.90 25.64 8.67

Change Gear Train Section:


70/1136/1 12229 11928 11287 100018 11286 11278 70/1132 A4736 70/1131 70/1909/1 33/072 Changewheel stud assembly Change gear stud Change gear bush Washer Cheese head screw (2BA x 3/8) Collar Grubscrew Spacer Change gear quadrant assembly Thumb screw Thumb nut Pack of 10 x 65000 2BA oil nipples 25.86 11.84 13.29 0.30 0.11 4.89 0.44 5.10 27.27 5.44 6.91 6.65 30.39 13.91 15.62 0.35 0.13 5.75 0..52 5.99 32.04 6.39 8.12 7.81

Rack, Leadscrew and Apron Section:


Note: Diecast apron spares for lathes with 5/8 diameter leadscrew prior to K111727. This does not include long bed machines. Rack with fixing screws - standard bed Rack with fixing screws - long bed Leadscrew - 5/8 dia - imperial - 8TPI - standard bed changewheel machine Leadscrew - 5/8 dia - imperial - 8TPI - standard bed quick change gearbox machine Hand traverse pinion Woodruff key Fibre washer

A9179 A9222 A4182 A4183 70/1316 70002 11258

40.03 70.27 134.44 134.44 19.41 0.53 0.18

47.04 82.57 157.97 157.97 22.81 0.62 0.21

Popular Spare Parts For ML7 Lathes


Rack, Leadscrew and Apron Section continued:
Part Number Description Price Excl. VAT Price Incl. VAT

73074 70/1331 70/1315 73001 70/1310/1ACC 11272 11271 100027 A4188/1 80003

Oilite bush (CT4 x 1.1/4) Handwheel assembly Rack pinion assembly Oilite bush (CT15 x ) Leadscrew nut assembly (includes 70/1326 cam peg, A4729 spring and 100319 2BA x 1.3/4 cap head screw) Adjusting screw - gib strip (MY2809) Adjusting screw - gib strip (MY2806) Hex locknut (2BA) Leadscrew guard Knob - cam and lever assembly Note: Cast iron apron spares for lathes with diameter leadscrew after K111727 and onwards. This also includes ALL long bed lathes. Rack with fixing screws - standard bed Rack with fixing screws - long bed Leadscrew - dia - imperial - 8TPI - standard bed changewheel machine Leadscrew - dia - imperial - 8TPI - long bed changewheel machine Leadscrew - dia - imperial - 8TPI - standard bed quick change machine Leadscrew - dia - imperial - 8TPI - long bed quick change gearbox machine Hand traverse pinion Woodruff key (No 404) Fibre washer (formerly MY4106) Handwheel assembly Rack pinion assembly Leadscrew nut assembly (includes 70/1326 cam peg, A4729 spring and 100319 2BA x 1.3/4 cap head screw) Adjusting screw - gib strip Adjusting screw - gib strip Hexagon locknut (2BA)

4.84 44.03 32.88 4.08 53.63 1.14 1.14 0.12 6.34 4.08

5.69 51.74 38.63 4.79 63.02 1.34 1.34 0.14 7.45 4.79

A9179 A9222 A2054/2 A3472/1 A3011/1 A3839/1 A2086 70002 11260 A2087/1 A2085 A1975/3ACC A9337 A9338 100027

40.03 70.27 78.63 82.02 68.23 71.16 19.78 0.53 0.18 52.08 44.49 53.63 3.78 3.78 0.12

47.04 82.57 92.39 96.37 80.17 83.61 23.24 0.62 0.21 61.19 52.28 63.02 4.44 4.44 0.14

Saddle and Cross Slide Section: N.B. : To ensure the best possible outcome when replacing worn feedscrews, replacement feedscrews are only available as an assembly fitted with a feednut.
Note: Saddle and Cross Slide - for lathes up to serial number K111727 with diecast apron and 5/8 diameter leadscrew. Wiper housing Round head screw (4BA x 3/8) Felt wiper Pack of 10 x 65000 2BA oil nipples Laminated shim - front

70/1327 100316 70/1328 33/072 70/1305

7.93 0.11 5.51 6.65 4.46

9.32 0.13 6.47 7.81 5.24

Popular Spare Parts For ML7 Lathes


Saddle and Cross Slide Section continued:
Part Number Description Price Excl. VAT Price Incl. VAT

70/1304 70/1311 100027 11296 100008 70/1312

Laminated shim - rear Saddle adjusting screw - gib strip Hexagon locknut (2BA) Hexagon head bolt - saddle clamping Washer (5/16) Clamp eccentric Note: Saddle and cross slide - for lathes after serial No K111727 with cast iron apron and diameter leadscrew 11271 Cross slide adjusting screw - gib strip (MY2806) for lathes up to serial No K108718 100027 Hexagon locknut (2BA) A8736 Wiper housing 100316 Round head screw (4BA x 3/8) A8735 Felt wiper 70/1305 Laminated shim - front 70/1304 Laminated shim - rear A7760 Saddle adjusting screw - gib strip A7424/1 Saddle adjusting screw - gib strip 100305 Hexagon locknut (1/4 BSF) 11296 Hexagon head bolt - saddle clamping 100008 Washer (5/16) 70/1312 Clamp eccentric A8623 Cross slide adjusting screw - gib strip for 70/1308/1 cross slide 100318 Cross slide adjusting screw - gib strip for 70/1308/1 cross slide 70/1308/1 Cross slide - standard - no longer available - use A1513/1 A1513/1 Cross slide - long - refer to General Accessory price list 20/209 and 20/210 70/1301 Cross slide end plate 30/133 Feedscrew - imperial - as above but fitted feednut standard cross slide 30/135 Feedscrew - imperial - as above but fitted feednut - long cross slide 70/1302 Feednut - imperial - 10TPI 30/134 Feedscrew - metric - as above but fitted feednut - standard cross slide 30/136 Feedscrew - metric - as above but fitted feednut - long cross slide A1648 Feednut - metric - 2mm pitch 70/1984A Hard washer 11257 Fibre washer 11107 Steel micrometer dial (replaces 70/1303 mazak dial) OR 20/252 Re-settable micrometer dial

4.46 2.93 0.12 1.55 0.11 4.71

5.24 3.44 0.14 1.82 0.13 5.53

1.14 0.12 7.93 0.11 5.51 4.46 4.46 2.24 2.64 0.04 1.55 0.11 4.71 2.03 0.43 127.82 12.08 32.22 37.09 12.52 32.22 37.09 12.52 0.21 0.16 15.84 34.55

1.34 0.14 9.32 0.13 6.47 5.24 5.24 2.63 2.63 0.05 1.82 0.13 5.53 2.39 0.51 150.19 14.19 37.86 43.58 14.71 37.86 43.58 14.71 0.25 0.19 18.61 40.60

Popular Spare Parts For ML7 Lathes


Saddle and Cross Slide Section continued:
Part Number Description Price Excl. VAT Price Incl. VAT

A1382/3 70/1337 A8623 100318

Gib strip Ball handle assembly Cross slide adjusting screw - gib strip Cross slide locking screw Note: For long bed ML7 lathes, refer to Super 7 spares list

3.26 17.68 2.03 0.43

3.83 20.77 2.39 0.51

Top Slide Section:


11292 13726 70/1403/1 70/1401 30/137 70/1302 30/138 Top slide assembly complete - imperial Top slide assembly complete - metric Top slide End plate Feedscrew - imperial - as above but fitted feednut Feednut - imperial - 10TPI Feedscrew - metric - 2mm pitch as above but fitted with feednut A1648 Feednut - metric - 2mm pitch 70/1984/A Hard washer 11257 Fibre washer 11107 Steel micrometer dial (replaces 70/1303 mazak dial) OR 20/252 Re-settable micrometer dial 11293 Ball handle assembly 11269 Adjusting screw - gib strip 100027 Hexagon locknut (2BA) 70/1406 Tool clamp stud A2806 Spring 70/1409/1 Tool clamp 70/1413 Adjusting screw assembly 70/1410 Spherical washer 70/1412 Tool clamp locking nut 15431 A1845 Tee nuts, complete with A7742 hexagon headed bolt and washers (for attaching the top slide to the cross slide) Note: For long bed ML7 lathes, refer to Super 7 spares list 222.84 222.84 80.97 12.03 29.64 12.52 29.64 12.52 0.21 0.16 15.84 34.55 12.42 0.45 0.12 10.75 0.71 12.19 7.57 3.09 3.09 12.82pr 261.84 261.84 95.14 14.14 34.83 14.71 34.83 14.71 0.25 0.19 18.61 40.60 14.59 0.53 0.14 12.63 0.83 14.32 8.89 3.63 3.63 15.06pr

Tailstock Section:
13356 A2798 70/1506 70/1520/1 70/1509 Tailstock assembly complete Barrel Barrel key Handwheel assembly Thrust plate 733.83 63.43 6.03 64.74 4.39 862.25 74.53 7.09 76.07 5.16

Popular Spare Parts For ML7 Lathes


Tailstock Section continued:
Part Number Description Price Excl. VAT Price Incl. VAT

70/1248 A2137 A2146 33/072

Hard centre - 2 MT Thrust screw - gib strip Set over screw Pack of 10 x 65000 2BA oil nipples

10.19 3.19 1.00 6.65

11.97 3.75 1.18 7.81

Plates:
A2639 Screw cutting chart Transfer for headstock belt guard 4.74 4.62 5.57 5.43

Sundries:
33/038 80163 80024 80025 15472 15473 Paint - grey - 250ml tin (air drying enamel) Castrol moly grease - 500gm tub - ideal for changewheels, feedscrews and leadscrews Lubricating oil - H32 Nuto - 1 litre for headstock spindle, tailstock barrel and oilite bushes Lubricating oil - Febis K68 - 1 litre for bed, slideways and gearbox New oil gun Set of 4 tee bolts with nuts and washers for fixing No 71 machine vice to cross slide or vertical slide Note: No 71 machine vice is no longer manufactured and is superceded by 78217 large capacity machine vice. 15.93 5.62 7.98 7.98 39.00 18.72 6.60 9.38 9.38 45.83

15.92

18.71

Installation and maintenance manuals


82005 82006 82021 82022 82023 ML7 Quick change gearbox Laminated screw cutting chart Laminated dividing chart (for 1445 dividing attachment and instructions on how to use the attachment) Myford wall chart - Wipe clean surface - Decimal equivalent and pitch tables - extremely useful in workshops 15.16 7.28 2.43 2.43 2.05 Nil Nil Nil Nil Nil

Popular Spare Parts For ML7 Lathes


Extra equipment:
Part Number Description Price Excl. VAT Price Incl. VAT

1480 1440A 30/021A 30/021 30/027

A1781 A1782 A1974/1

Quick change gearbox Lever operated tailstock attachment Chuck guard for machines before lathe serial No K91000 Chuck guard for machines after lathe serial No K91000 Chuck guard kit to meet requirements of Health and Safety at Work Act 1974, comprising: Primary drive guard backplate, guard for rear end of headstock spindle and guard for swing head, including No 30/021 chuck guard for machines after lathe serial No K91000 (please state serial number of machine) 18T Tufnol pinion for tumbler reverse 20T Tufnol pinion for tumbler reverse Fine feed tumbler cluster gear

1313.81 132.74 102.61 64.28

1543.73 155.97 120.57 75.53

130.12 22.68 22.68 29.87

152.89 26.65 26.65 35.10

Published by Myford Ltd - Printed in Great Britain - Copyright 2010 Myford Ltd All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the publishers. Illustrations are not binding in detail. Design and specification subject to change without notice.

MYFORD LTD
Wilmot Lane, Chilwell Road, Beeston, Nottingham, England NG9 1ER

Telephone (0115) 9254222


Fax (0115) 9431299 Website address: www.myford.com Email address: sales@myford.com

You might also like