You are on page 1of 20

19-2322; Rev 2; 9/03

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable


General Description
The MAX4389/MAX4390/MAX4392MAX4396 family of op amps are unity-gain stable devices that combine high-speed performance, Rail-to-Rail outputs, and disable mode. These devices are targeted for applications where an input or an output is exposed to the outside world, such as video and communications. The MAX4389/MAX4390/MAX4392MAX4396 operate from a single 4.5V to 11V supply or from dual 2.25V to 5.5V supplies. The common-mode input voltage range extends to the negative power-supply rail (ground in single-supply applications). The MAX4389/MAX4390/ MAX4392MAX4396 consume only 5.5mA of quiescent supply current per amplifier while achieving a 85MHz -3dB bandwidth, 27MHz 0.1dB gain flatness, and a 500V/s slew rate. Disable mode sets the outputs to high impedance while consuming only 450A of current. The MAX4389 single, MAX4393 dual, MAX4394 triple, and MAX4396 quad include disable capabilities. The MAX4389 and MAX4390 are available in ultra-small, 6-pin SC70 packages. o Low Cost o High Speed 85MHz -3dB Bandwidth 27MHz 0.1dB Gain Flatness 500V/s Slew Rate o Single 4.5V to 11V or Dual 2.25V to 5.5V Operation o Rail-to-Rail Outputs o Input Common-Mode Range Extends to VEE o Low Differential Gain/Phase: 0.015%/0.015 o Low Distortion at 5MHz -59dBc Spurious-Free Dynamic Range o High Output Drive: 50mA o 450A Disable Capability (MAX4389/MAX4393/MAX4394/MAX4396) o Space-Saving SC70, SOT23, MAX, or TSSOP Packages

Features

MAX4389/MAX4390/MAX4392MAX4396

Applications
Set-Top Boxes Surveillance Video Systems Analog-to-Digital Converter Interface CCD Imaging Systems Digital Cameras Video-on-Demand Video Line Driver
MAX4389EXT-T MAX4389EUT-T MAX4390EXT-T MAX4390EUK-T PART

Ordering Information
TEMP RANGE -40C to +85C -40C to +85C -40C to +85C -40C to +85C PINPACKAGE 6 SC70-6 6 SOT23-6 6 SC70-6 5 SOT23-5 TOP MARK ABF ABDC ABE ADZM

Ordering Information continued at end of data sheet. Selector Guide appears at end of data sheet.

Typical Operating Circuit


DISABLE IN 75 MAX4389 Zo = 75 OUT

Pin Configurations
TOP VIEW
OUT 1 6 VCC

VEE 2
75

MAX4389

DISABLE

IN+ 3
200 200

IN-

SC70/SOT23
VIDEO LINE DRIVER

Pin Configurations continued at end of data sheet.

Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. ________________________________________________________________ Maxim Integrated Products 1

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxims website at www.maxim-ic.com.

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VCC to VEE) ..................................-0.3V to +12V IN_+, IN_-, OUT_, DISABLE.............(VEE - 0.3V) to (VCC + 0.3V) Differential Input Voltage ....................................................2.5V Current into Input Pins ......................................................20mA Output Short-Circuit Duration to VCC or VEE (Note 1)................................................Continuous Continuous Power Dissipation (TA = +70C) 5-Pin SOT23 (derate 7.1mW/C above +70C)............571mW 6-Pin SOT23 (derate 8.7mW/C above +70C)............696mW 6-Pin SC70 (derate 3.1mW/C above +70C) ..............245mW Note 1: Continuous power dissipation must also be observed.
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

8-Pin SO (derate 5.88mW/C above +70C)................471mW 8-Pin MAX (derate 4.5mW/C above +70C) .............362mW 10-Pin MAX (derate 5.6mW/C above +70C) ...........444mW 14-Pin SO (derate 8.33mW/C above +70C)..............667mW 14-Pin TSSOP (derate 10mW/C above +70C) ..........727mW 20-Pin TSSOP (derate 10.9mW/C above +70C) .......879mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C

DC ELECTRICAL CHARACTERISTICSSingle Supply


(VCC = 5V, VEE = 0V, VCM = VCC/2, VOUT = VCC/2, RL = to VCC/2, DISABLE_ = VCC (MAX4389/MAX4393/MAX4394/MAX4396), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 2)
PARAMETER Input Common-Mode Voltage Range Input Offset Voltage Input Offset Voltage Matching Input Offset Voltage Tempco Input Bias Current Input Offset Current Input Resistance Common-Mode Rejection Ratio Open-Loop Gain TCVOS IB IOS RIN CMRR AVOL Differential mode (-1V VIN +1V) Common mode (-0.2V VCM +2.75V) (VEE - 0.2V) VCM (VCC - 2.25V) 0.25V VOUT 4.75V, RL = 2k 0.8V VOUT 4.5V, RL = 150 1V VOUT 4V, RL = 50 RL = 2k RL = 150 Output Voltage Swing VOUT RL = 75 RL = 75 to ground Output Current Output Short-Circuit Current Open-Loop Output Resistance IOUT ISC ROUT VCC - VOH VOL - VEE VCC - VOH VOL - VEE VCC - VOH VOL - VEE VCC - VOH VOL - VEE 40 40 70 50 50 SYMBOL VCM VOS CONDITIONS Guaranteed by CMRR test TA = +25C TA = -40C to +85C MAX4392MAX4396 1 15 2.5 0.2 70 3 95 70 60 58 0.065 0.05 0.3 0.25 0.5 0.45 1 0.025 55 50 100 8 0.25 0.15 0.5 0.5 0.8 0.8 1.7 0.1 mA mA V dB 15 5 MIN VEE 0.2 5 TYP MAX VCC 2.25 18 26 UNITS V mV mV V/C A A k M dB

Sinking from RL = 75 to VCC Sourcing into RL = 75 to VEE Sinking or sourcing

_______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable


DC ELECTRICAL CHARACTERISTICSSingle Supply (continued)
(VCC = 5V, VEE = 0V, VCM = VCC/2, VOUT = VCC/2, RL = to VCC/2, DISABLE_ = VCC (MAX4389/MAX4393/MAX4394/MAX4396), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 2)
PARAMETER Power-Supply Rejection Ratio Operating Supply Voltage Range Disabled Output Resistance DISABLE_ Logic-Low Threshold DISABLE_ Logic-High Threshold DISABLE_ Logic Input Low Current DISABLE_ Logic Input High Current Quiescent Supply Current (Per Amplifier) SYMBOL PSRR VS ROUT(OFF) VIL VIH IIL IIH IS DISABLE_ = 0 DISABLE_ = VCC DISABLE_ = VCC DISABLE_ = 0 VCC 1.25 20 5 3.2 0.3 60 40 5 0.4 CONDITIONS VEE = 0V, VCC = 4.5V to 5.5V Guaranteed by PSRR DISABLE_ = 0, 0 VOUT 5V MIN 48 4.5 40 95 VCC - 3 TYP 65 11 MAX UNITS dB V k V V A A mA

MAX4389/MAX4390/MAX4392MAX4396

DC ELECTRICAL CHARACTERISTICSDual Supply


(V CC = 5V, V EE = -5V, V CM = 0V, V OUT = 0V, R L = to 0, DISABLE_ = V CC (MAX4389/MAX4393/MAX4394/MAX4396), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 2)
PARAMETER Input Common-Mode Voltage Input Offset Voltage Input Offset Voltage Matching Input Offset Voltage Tempco Input Bias Current Input Offset Current Input Resistance Common-Mode Rejection Ratio Open-Loop Gain TCVOS IB IOS RIN CMRR AVOL Differential mode (-1V VIN +1V) Common mode (-0.2V VCM +2.75V) VEE VCM (VCC - 2.25V) -4.5V VOUT 4.5V, RL = 2k -4.25V VOUT 4.25V, RL = 150 70 65 50 SYMBOL VCM VOS TA = +25C TA = -40C to +85C MAX4392MAX4396 1 20 5 0.5 70 3 90 80 60 15 5 CONDITIONS Guaranteed by CMRR test MIN VEE 7 TYP MAX VCC - 2.25 20 28 UNITS V mV mV V/C A A k M dB dB

_______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
DC ELECTRICAL CHARACTERISTICSDual Supply (continued)
(V CC = 5V, V EE = -5V, V CM = 0V, V OUT = 0V, R L = to 0, DISABLE_ = V CC (MAX4389/MAX4393/MAX4394/MAX4396), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 2)
PARAMETER SYMBOL RL = 2k Output Voltage Swing VOUT RL = 150 RL = 75 Output Current Output Short-Circuit Current Open-Loop Output Resistance Power-Supply Rejection Ratio Operating Supply Voltage Range Disabled Output Resistance DISABLE_ Logic-Low Threshold DISABLE_ Logic-High Threshold Quiescent Supply Current (Per Amplifier) IOUT ISC ROUT PSRR VS ROUT(OFF) VIL VIH IS DISABLE_ = VCC DISABLE_ = 0V VCC - 1.25 6 0.45 10 0.8 VEE = 0V, VCC = 4.5V to 5.5V Guaranteed by PSRR DISABLE_ = 0V, -5V VOUT +5V 48 4.5 40 95 VCC - 3 CONDITIONS VCC - VOH VOL - VEE VCC - VOH VOL - VEE VCC - VOH VOL - VEE 50 50 MIN TYP 0.175 0.075 0.575 0.4 1.5 0.75 95 75 100 8 60 11 MAX 0.3 0.2 0.85 1.5 2.35 1.6 mA mA dB V k V V mA V UNITS

Sinking from RL = 75 to VCC Sourcing into RL = 75 to VEE Sinking or sourcing

AC ELECTRICAL CHARACTERISTICSSingle Supply


(V CC = 5V, V EE = 0V, V CM = 1.5V, R L = 100 to V CC /2, DISABLE_ = V CC (MAX4389/MAX4393/MAX4394/MAX4396), VOUT = VCC/2, AVCL = 1V/V, TA = +25C, unless otherwise noted.)
PARAMETER Small-Signal -3dB Bandwidth Large-Signal -3dB Bandwidth Small-Signal 0.1dB Gain Flatness Large-Signal 0.1dB Gain Flatness Slew Rate Settling Time to 0.1% Rise/Fall Time Spurious-Free Dynamic Range SYMBOL BWSS BWLS BW0.1dBSS BW0.1dBLS SR ts tR/tF SFDR VOUT = 2VP-P VOUT = 100mVP-P VOUT = 2VP-P VOUT = 2V step VOUT = 2V step VOUT = 100mVP-P fC = 5MHz, VOUT = 2VP-P CONDITIONS VOUT = 100mVP-P MIN TYP 72 80 30 30 500 28 4 -59 MAX UNITS MHz MHz MHz MHz V/s ns ns dBc

_______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable


AC ELECTRICAL CHARACTERISTICSSingle Supply (continued)
(V CC = 5V, V EE = 0V, V CM = 1.5V, R L = 100 to V CC /2, DISABLE_ = V CC (MAX4389/MAX4393/MAX4394/MAX4396), VOUT = VCC/2, AVCL = 1V/V, TA = +25C, unless otherwise noted.)
PARAMETER Differential Phase Error Differential Gain Error Input Noise-Voltage Density Input Noise-Current Density Input Capacitance Output Impedance Disable OFF Time Disable ON Time Channel-to-Channel Isolation CHISO SYMBOL DP DG en in CIN ZOUT f = 5MHz MAX4389/MAX4393/MAX4394/MAX4396 MAX4389/MAX4393/MAX4394/MAX4396 MAX4392MAX4396, specified at DC CONDITIONS NTSC, RL = 150 NTSC, RL = 150 f = 10kHz f = 10kHz MIN TYP 0.015 0.015 13 2.1 1 0.6 80 40 -97 MAX UNITS degrees % nV/Hz pA/Hz pF ns ns dB

MAX4389/MAX4390/MAX4392MAX4396

AC ELECTRICAL CHARACTERISTICSDual Supply


(VCC = 5V, VEE = -5V, RL = to GND, GND = 0, VOUT = 0V, Gain = 1V/V, DISABLE = VCC, and TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.)
PARAMETER Small-Signal -3dB Bandwidth Large-Signal -3dB Bandwidth Small-Signal Bandwidth for 0.1dB Gain Flatness Large-Signal Bandwidth for 0.1dB Gain Flatness Slew Rate Settling Time to 0.1% Rise/Fall Time Spurious-Free Dynamic Range Differential Phase Error Differential Gain Error Input Noise-Voltage Density Input Noise-Current Density Input Capacitance Output Impedance Disable OFF Time Disable ON Time Channel-to-Channel Isolation CHISO SYMBOL BWSS BWLS BW0.1dBss BW0.1dBLS SR tS tR/tF SFDR DP DG en in CIN ZOUT f = 5MHz MAX4389/MAX4393/MAX4394/MAX4396 MAX4389/MAX4393/MAX4394/MAX4396 MAX4392/MAX4393/MAX4394/MAX4395/ MAX4396, specified at DC VOUT = 2VP-P VOUT = 100mVP-P VOUT = 2VP-P VOUT = 2V step VOUT = 2V step VOUT = 100mVP-P fC = 5MHz, VOUT = 2VP-P NTSC, RL = 150 NTSC, RL = 150 f = 10kHz f = 10kHz CONDITIONS VOUT = 100mVP-P MIN TYP 85 90 27 24 500 21 4 -59 0.015 0.015 13 2.1 1 0.6 80 40 -97 MAX UNITS MHz MHz MHz MHz V/s ns ns dBc degrees % nV/Hz pA/Hz pF ns ns dB

Note 2: All devices are 100% production tested at TA = +25C. Specifications over temperature limits are guaranteed by design.

_______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
Typical Operating Characteristics
(VCC = 5V, VEE = -5V, VCM = 0V, AVCL = 1V/V, RL = 100 to GND, GND = 0, TA = +25C, unless otherwise noted.)
GAIN AND PHASE vs. FREQUENCY
80 60 40 20 GAIN (dB) 0 -20 -40 -60 -80 -100 -120 1k 10k 100k 1M 10M 100M 1G FREQUENCY (Hz) PHASE GAIN
MAX4389 toc01

SMALL-SIGNAL GAIN vs. FREQUENCY


MAX4389 toc02

LARGE-SIGNAL GAIN vs. FREQUENCY


3 2 1 GAIN (dB) 0 -1 -2 -3 -4 -5 -6 VOUT = 2VP-P
MAX4389 toc03

180 135 90 PHASE (DEGREES) GAIN (dB) 45 0 -45 -90 -135 -180 -225 -270

4 3 2 1 0 -1 -2 -3 -4 -5 -6

VOUT = 100mVP-P

100k

1M

10M FREQUENCY (Hz)

100M

1G

100k

1M

10M FREQUENCY (Hz)

100M

1G

SMALL-SIGNAL GAIN FLATNESS vs. FREQUENCY


MAX4389 toc04

LARGE-SIGNAL GAIN FLATNESS vs. FREQUENCY


0.3 0.2 0.1 GAIN (dB) 0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 0.01 100k 1M 10M FREQUENCY (Hz) 100M 1G VOUT = 2VP-P
MAX4389 toc05

OUTPUT IMPEDANCE vs. FREQUENCY


MAX4389 toc06

0.4 0.3 0.2 0.1 GAIN (dB) 0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6

VOUT = 100mVP-P

0.4

100

OUTPUT IMPEDANCE ()

10

0.1

100k

1M

10M FREQUENCY (Hz)

100M

1G

100k

1M

10M FREQUENCY (Hz)

100M

1G

DISTORTION vs. FREQUENCY


MAX4389 toc07

DISTORTION vs. FREQUENCY


MAX4389 toc08

DISTORTION vs. FREQUENCY


-10 -20 DISTORTION (dBc) -30 -40 -50 -60 -70 -80 -90 -100 2ND HARMONIC 3RD HARMONIC VOUT = 2VP-P, AVCL = 5V/V
MAX4389 toc09

0 -10 -20 DISTORTION (dBc) -30 -40 -50 -60 -70 -80 -90 -100 100k 1M 10M 3RD HARMONIC 2ND HARMONIC VOUT = 2VP-P, AVCL = 1V/V

0 -10 -20 DISTORTION (dBc) -30 -40 -50 -60 -70 -80 -90 -100 3RD HARMONIC 2ND HARMONIC VOUT = 2VP-P, AVCL = 2V/V

100M

100k

1M

10M

100M

100k

1M

10M

100M

FREQUENCY (Hz)

FREQUENCY (Hz)

FREQUENCY (Hz)

_______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
Typical Operating Characteristics (continued)
(VCC = 5V, VEE = -5V, VCM = 0V, AVCL = 1V/V, RL = 100 to GND, GND = 0, TA = +25C, unless otherwise noted.)

DISTORTION vs. RESISTIVE LOAD


MAX4389 toc10

DISTORTION vs. VOLTAGE SWING


DIFF GAIN (%) -10 -20 DISTORTION (dBc) -30 -40 -50 DIFF PHASE () -60 -70 -80 3RD HARMONIC 2ND HARMONIC fo = 5MHz, AVCL = 1V/V
MAX4389 toc11

DIFFERENTIAL GAIN AND PHASE


0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 0.5 0.4 0.3 0.2 0.1 0 -0.1 0 1 RL = 150 TO GND, AVCL = 2V/V
MAX4389 toc12

0 -10 -20 DISTORTION (dBc) -30 -40 -50 -60 -70 -80 -90 -100 0 200 400 600 800 1000 3RD HARMONIC 2ND HARMONIC fo = 5MHz, VOUT = 2VP-P, AVCL = 1V/V

-90 -100 1200 0.5 1.0 1.5 2.0

RL = 150 TO GND, AVCL = 2V/V 2 3 IRE 4 5 6

VOLTAGE SWING (VP-P)

VOLTAGE SWING (VP-P)

COMMON-MODE REJECTION vs. FREQUENCY


MAX4389 toc13

POWER-SUPPLY REJECTION vs. FREQUENCY


MAX4389 toc14

OUTPUT VOLTAGE SWING vs. RESISTIVE LOAD


1.4 OUTPUT VOLTAGE SWING (V) 1.2 1.0 0.8 0.6 0.4 0.2 VOL- VEE 0 VCC - VOH
MAX4389 toc15

0 -10 -20 GAIN (dB)

0 -10 -20 PSR (dB) -30 -40 -50 -60 -70

1.6

-30 -40 -50 -60 -70 -80 100k 1M 10M FREQUENCY (Hz) 100M 1G

100k

1M

10M FREQUENCY (Hz)

100M

1G

100

200

300 RLOAD ()

400

500

600

SMALL-SIGNAL PULSE RESPONSE


AVCL = 1V/V INPUT 50mV/div
MAX4389 toc16

SMALL-SIGNAL PULSE RESPONSE


MAX4389 toc17

SMALL-SIGNAL PULSE RESPONSE


AVCL = 5V/V RF = 250 INPUT 10mV/div
MAX4389 toc18

AVCL = 2V/V AVCL = +2V/V RF = 200 RF = 200 INPUT 25mV/div

OUTPUT 50mV/div

OUTPUT 50mV/div

OUTPUT 50mV/div

20ns/div

20ns/div

20ns/div

_______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
Typical Operating Characteristics (continued)
(VCC = 5V, VEE = -5V, VCM = 0V, AVCL = 1V/V, RL = 100 to GND, GND = 0, TA = +25C, unless otherwise noted.)

LARGE-SIGNAL PULSE RESPONSE


MAX4389 toc19

LARGE-SIGNAL PULSE RESPONSE


AVCL = 2V/V RF = 200 INPUT 250mV/div
MAX4389 toc20

LARGE-SIGNAL PULSE RESPONSE


AVCL = 5V/V RF = 250 INPUT 100mV/div
MAX4389 toc21

AVCL = 1V/V INPUT 500mV/div

OUTPUT 500mV/div

OUTPUT 500mV/div

OUTPUT 500mV/div

20ns/div

20ns/div

20ns/div

VOLTAGE NOISE vs. FREQUENCY


MAX4389 toc22

CURRENT NOISE vs. FREQUENCY


MAX4389 toc23

ISOLATION RESISTANCE vs. CAPACITIVE LOAD


5 4 3 2 GAIN (dB) 1 0 -1 -2 -3 -4 100pF
MAX4389 toc24

1000 RL = 100 VOLTAGE NOISE (nV/Hz)

1000 RL = 100 CURRENT NOISE (pA/Hz)

100

100

68pF

33pF

10

10

1 1 10 100 1k 10k 100k FREQUENCY (Hz)

1 1 10 100 1k 10k 100k FREQUENCY (Hz)

-5 -6 100k 1M 10M FREQUENCY (Hz) 100M 1G

_______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
Typical Operating Characteristics (continued)
(VCC = 5V, VEE = -5V, VCM = 0V, AVCL = 1V/V, RL = 100 to GND, GND = 0, TA = +25C, unless otherwise noted.)
SMALL-SIGNAL BANDWIDTH vs. LOAD RESISTANCE
MAX4389 toc25

OPEN-LOOP GAIN vs. RESISTIVE LOAD


MAX4389 toc26

CROSSTALK vs. FREQUENCY


-10 -20 CROSSTALK (dB) -30 -40 -50 -60 -70 -80 -90 -100
MAX4389 toc27

140 120 BANDWIDTH (MHz) 100 80 60 40 20 0 0

80 70 OPEN-LOOP GAIN (dBc) 60 50 40 30 20 10 0

100 200 300 400 500 600 700 800 RLOAD ()

100

1k RLOAD ()

10k

100k

1M

10M FREQUENCY (Hz)

100M

1G

DISABLE RESPONSE
MAX4389 toc28

INPUT OFFSET VOLTAGE vs. TEMPERATURE


MAX4389 toc29

INPUT BIAS CURRENT vs. TEMPERATURE


7 INPUT BIAS CURRENT (A) 6 5 4 3 2 1 0 -50 -25 0 25 50 75 100
MAX4389 toc30

8 7 INPUT OFFSET VOLTAGE (mV) 6 5 4 3 2 1 0

5V DISABLE 0V

1.5V VOUT 0V 200ns/div

-50

-25

25

50

75

100

TEMPERATURE (C)

TEMPERATURE (C)

SUPPLY CURRENT vs. TEMPERATURE


7 SUPPLY CURRENT (mA) 6 5 4 3 2 1 0 -50 -25 0 25 50 75 100 TEMPERATURE (C)
MAX4389 toc31

_______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
Pin Description
PIN MAX4389 SC70/SOT23 1 MAX4390 SC70 1 SOT23 1 MAX4392 MAX/SO MAX4393 MAX MAX4394 SO/TSSOP MAX4395 SO/TSSOP MAX4396 TSSOP OUT Amplifier Output Negative Power Supply. Connect a 0.1F Capacitor to GND. Noninverting Input Inverting Input Disable. Connect to VCC to Enable. Positive Power Supply. Connect a 0.1F Capacitor to GND. No Connection. Not Internally Connected. Amplifier A Noninverting Input Amplifier A Inverting Input Amplifier A Output Shutdown Amplifier A. Connect to VCC to Enable. Amplifier B Noninverting Input Amplifier B Inverting Input Amplifier B Output NAME FUNCTION

11

11

16

VEE

3 4 5

3 4

3 4

IN+ INDISABLE

10

VCC

10, 11

N.C.

INA+

2 1

2 1

6 7

2 1

3 2

INAOUTA

DISABLEA

10

INB+

6 7

8 9

9 8

6 7

7 8

INBOUTB

10

______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable


Pin Description (continued)
PIN MAX4389 SC70/SOT23 MAX4390 SC70 SOT23 MAX4392 MAX/SO MAX4393 MAX MAX4394 SO/TSSOP MAX4395 SO/TSSOP MAX4396 TSSOP Shutdown Amplifier B. Connect to VCC to Enable. Amplifier C Noninverting Input Amplifier C Inverting Input Amplifier C Output Shutdown Amplifier C. Connect to VCC to Enable. Amplifier D Noninverting Input Amplifier D Inverting Input Amplifier D Output Shutdown Amplifier D. Connect to VCC to Enable. NAME FUNCTION

MAX4389/MAX4390/MAX4392MAX4396

DISABLEB

12

10

15

INC+

13 14

9 8

14 13

INCOUTC

12

DISABLEC

12

17

IND+

13 14

18 19

INDOUTD

20

DISABLED

Detailed Description
The MAX4389/MAX4390/MAX4392MAX4396 are dualsupply, rail-to-rail, voltage-feedback amplifiers that employ current-feedback techniques to achieve 500V/s slew rates and 85MHz bandwidths. Excellent harmonic distortion and differential gain/phase performance make these amplifiers an ideal choice for a wide variety of video and RF signal-processing applications.

gain sensitivity to load variations. The input stage permits common-mode voltages to the negative supply and to within 2.25V of the positive supply rail.

Choosing Resistor Values


Unity-Gain Configuration The MAX4389/MAX4390/MAX4392MAX4396 are internally compensated for unity gain. When configured for unity gain, a 24 resistor (RF) in series with the feedback path optimizes AC performance. This resistor improves AC response by reducing the Q of the parallel LC circuit formed by the parasitic feedback capacitance and inductance.

Applications Information
The output voltage swings to within 200mV of each supply rail. Local feedback around the output stage ensures low open-loop output impedance to reduce

______________________________________________________________________________________

11

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
Video Line Driver The MAX4389/MAX4390/MAX4392MAX4396 are lowpower, voltage-feedback amplifiers featuring large-signal (2V P-P) bandwidths of 90MHz and 0.1dB largesignal gain flatness of 24MHz. They are designed to minimize differential-gain error and differential-phase error to 0.015% and 0.015, respectively. They have a 21ns settling time to 0.1%, 500V/s slew rates, and output-current-drive capability of up to 50mA making them ideal for driving video loads. Inverting and Noninverting Configurations Select the gain-setting feedback (RF) and input (RG) resistor values to fit your application. Large resistor values increase voltage noise and interact with the amplifiers input and PC board capacitance. This can generate undesirable poles and zeros and decrease bandwidth or cause oscillations. For example, a noninverting gain-of-two configuration (RF = RG) using 2k resistors, combined with 1pF of amplifier input capacitance and 1pF of PC board capacitance, causes a pole at 79.6MHz. Since this pole is within the amplifier bandwidth, it jeopardizes stability. Reducing the 2k resistors to 100 extends the pole frequency to 1.59GHz, but could limit output swing by adding 200 in parallel with the amplifiers load resistor (Figures 1a and 1b).

Layout and Power-Supply Bypassing


The MAX4389/MAX4390/MAX4392MAX4396 operate from single 4.5V to 11V or from dual 2.25V to 5.5V supplies. Bypass each supply with a 0.1F capacitor as close to the pin as possible. Maxim recommends using microstrip and stripline techniques to obtain full bandwidth. To ensure that the PC board does not degrade the amplifiers performance, design it for a frequency greater than 1GHz. Pay careful attention to inputs and outputs to avoid large parasitic capacitance. Whether or not you use a constant-impedance board, observe the following design guidelines: Do not use wire-wrap boards; they are too inductive. Do not use IC sockets; they increase parasitic capacitance and inductance. Use surface-mount instead of through-hole components for better, high-frequency performance. Use a PC board with at least two layers; it should be as free from voids as possible. Keep signal lines as short and as straight as possible. Do not make 90 turns; round all corners.

Low-Power Disable Mode


The MAX4389/MAX4393/MAX4394/MAX4396 feature a disable function that allows the amplifiers to be placed in a low-power, high-output-impedance state. When the disable pin (DISABLE) is active, the amplifiers output impedance is 95k. This high resistance and the low 2pF output capacitance make the MAX4389/ MAX4390/MAX4392MAX4396 in RF/video multiplexer or switch applications. For larger arrays, pay careful attention to capacitive loading (see the Output Capacitive Loading and Stability section).

RG

RF

MAX43_ _

VOUT

VIN

VOUT = [1 + (RF / RG)] VIN

Output Capacitive Loading and Stability


Figure 1a. Noninverting Gain Configuration

RG VIN

RF

MAX43_ _

VOUT

VOUT = -(RF / RG) VIN

Figure 1b. Inverting Gain Configuration

The MAX4389/MAX4390/MAX4392MAX4396 are optimized for AC performance. They are not designed to drive highly reactive loads, which decrease phase margin and may produce excessive ringing and oscillation. Figure 2 shows a circuit that eliminates this problem. Figure 3 is a graph of the Optimal Isolation Resistor (RS) vs. Capacitive Load. Figure 4 shows how a capacitive load causes excessive peaking of the amplifiers frequency response if the capacitor is not isolated from the amplifier by a resistor. A small isolation resistor (usually 10 to 15) placed before the reactive load prevents ringing and oscillation. At higher capacitive loads, AC performance is controlled by the interaction of the load capacitance and the isolation resistor. Figure 5 shows the effect of a 15 isolation resistor on closed-loop response.

12

______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
RG RF

6 5
RISO

4
VOUT

MAX438 _

3 2 GAIN (dB) 1 0 -1 -2 -3 -4 -5 -6 100k 1M

VIN

CL

120pF

68pF

Figure 2. Driving a Capacitive Load Through an Isolation Resistor

180pF

16 15 14 RISO () 13 12 11 10 9 0 50 100 150 200 250 300 350 400 450 500 550 CLOAD (pF) SMALL SIGNAL (VOUT = 100mVP-P) LARGE SIGNAL (VOUT = 2VP-P)

10M FREQUENCY (Hz)

100M

1G

Figure 5. Small-Signal Gain vs. Frequency with Load Capacitance and 27 Isolation Resistor

Chip Information
MAX4389 TRANSISTOR COUNT: 70 MAX4390 TRANSISTOR COUNT: 70 MAX4392 TRANSISTOR COUNT: 204 MAX4393 TRANSISTOR COUNT: 204 MAX4394 TRANSISTOR COUNT: 298 MAX4395 TRANSISTOR COUNT: 396 MAX4396 TRANSISTOR COUNT: 396 PROCESS: BiCMOS

Figure 3. Isolation Resistance vs. Capacitive Load

6 5 4 3 2 GAIN (dB) 1 0 -1 -2 -3 -4 -5 -6 100k 1M

100pF

68pF

33pF

10M FREQUENCY (Hz)

100M

1G

Figure 4. Small-Signal Gain vs. Frequency with Load Capacitance and No Isolation Resistor ______________________________________________________________________________________ 13

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
Pin Configurations (continued)

TOP VIEW
OUT 1 6 VCC

TOP VIEW
OUT 1 5 VCC

VEE 2

MAX4390

N.C.

VEE 2

MAX4390
4 IN-

IN+ 3

IN-

IN+ 3

SC70

SOT23

TOP VIEW
OUTA 1 INAINA+ VEE 2 3 4 8 7 VCC OUTB INBINB+

TOP VIEW
OUTA 1 INAINA+ VEE DISABLEA 2 3 4 5 10 VCC 9 OUTB INBINB+ DISABLEB

MAX4392

6 5

MAX4393

8 7 6

MAX/SO

MAX

TOP VIEW
DISABLEA 1 DISABLEC 2 DISABLEB 3 VCC 4 INA+ 5 INA- 6 OUTA 7 14 OUTC 13 INC12 INC+

TOP VIEW
OUTA 1 INAINA+ 2 3 14 OUTD 13 IND12 IND+

MAX4394

11 VEE 10 INB+ 9 8 INBOUTB

VCC 4 INB+ 5 INB- 6 OUTB 7

MAX4395

11 VEE 10 INC+ 9 8 INCOUTC

SO/TSSOP

SO/TSSOP

14

______________________________________________________________________________________

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable


Pin Configurations (continued) Ordering Information (continued)
PART TEMP RANGE -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C PINPACKAGE 8 MAX 8 SO 10 MAX 14 SO 14 TSSOP 14 SO 14 TSSOP 20 TSSOP TOP MARK

MAX4389/MAX4390/MAX4392MAX4396

TOP VIEW
DISABLEA 1 OUTA 2 INA- 3 INA+ 4 VCC 5 INB+ 6 INB- 7 OUTB 8 DISABLEB 9 N.C. 10 20 DISABLED 19 OUTD 18 IND17 IND+

MAX4392EUA MAX4392ESA MAX4393EUB MAX4394ESD MAX4394EUD MAX4395ESD MAX4395EUD MAX4396EUP

MAX4396

16 VEE 15 INC+ 14 INC13 OUTC 12 DISABLEC 11 N.C.

Selector Guide
PART MAX4389 MAX4390 MAX4392 MAX4393 MAX4394 MAX4395 MAX4396 NO. OF AMPS 1 1 2 2 3 4 4 DISABLE Yes No No Yes Yes No Yes

TSSOP

______________________________________________________________________________________

15

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)
SC70, 6L.EPS

PACKAGE OUTLINE, SOT-23, 6L

21-0058

1 1

16

______________________________________________________________________________________

6LSOT.EPS

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable


Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)
SOT-23 5L .EPS

MAX4389/MAX4390/MAX4392MAX4396

PACKAGE OUTLINE, SOT-23, 5L

21-0057

1 1

4X S

INCHES DIM A A1 A2 b MIN 0.002 0.030 MAX 0.043 0.006 0.037

MILLIMETERS MAX MIN 0.05 0.75 1.10 0.15 0.95

0.500.1

0.60.1

c D e E H L
1

1
0.60.1

BOTTOM VIEW

0.010 0.014 0.005 0.007 0.116 0.120 0.0256 BSC 0.116 0.120 0.188 0.198 0.016 0.026 6 0 0.0207 BSC

0.25 0.36 0.13 0.18 2.95 3.05 0.65 BSC 2.95 3.05 4.78 5.03 0.41 0.66 0 6 0.5250 BSC

TOP VIEW

A2

A1

c e b L

SIDE VIEW

FRONT VIEW

PROPRIETARY INFORMATION TITLE:

PACKAGE OUTLINE, 8L uMAX/uSOP


APPROVAL DOCUMENT CONTROL NO. REV.

21-0036

1 1

______________________________________________________________________________________

8LUMAXD.EPS

17

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392MAX4396
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)
e
10

4X S
10

INCHES MAX DIM MIN A 0.043 A1 0.002 0.006 A2 0.030 0.037 D1 0.116 0.120 D2 0.114 0.118 E1 0.116 0.120 0.118 E2 0.114 0.199 H 0.187 L 0.0157 0.0275 L1 0.037 REF b 0.007 0.0106 e 0.0197 BSC c 0.0035 0.0078 0.0196 REF S 0 6

MILLIMETERS MAX MIN 1.10 0.15 0.05 0.75 0.95 3.05 2.95 3.00 2.89 3.05 2.95 2.89 3.00 4.75 5.05 0.40 0.70 0.940 REF 0.177 0.270 0.500 BSC 0.090 0.200 0.498 REF 0 6

H 0.500.1 0.60.1

0.60.1

TOP VIEW

BOTTOM VIEW

D2 GAGE PLANE A2 A b A1 D1

E2

E1 L1

FRONT VIEW

SIDE VIEW

PROPRIETARY INFORMATION TITLE:

PACKAGE OUTLINE, 10L uMAX/uSOP


APPROVAL DOCUMENT CONTROL NO. REV.

21-0061

1 1

INCHES DIM A A1 B C e E H L MAX MIN 0.069 0.053 0.010 0.004 0.014 0.019 0.007 0.010 0.050 BSC 0.150 0.157 0.228 0.244 0.016 0.050

MILLIMETERS MAX MIN 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 1.27 BSC 3.80 4.00 5.80 6.20 0.40 1.27

VARIATIONS:
1

INCHES

MILLIMETERS MIN 4.80 8.55 9.80 MAX 5.00 8.75 10.00 N MS012 8 AA 14 AB 16 AC

TOP VIEW

DIM D D D

MIN 0.189 0.337 0.386

MAX 0.197 0.344 0.394

D C

A e B A1

0-8 L

FRONT VIEW

SIDE VIEW

PROPRIETARY INFORMATION TITLE:

PACKAGE OUTLINE, .150" SOIC


APPROVAL DOCUMENT CONTROL NO. REV.

21-0041

1 1

18

______________________________________________________________________________________

SOICN .EPS

10LUMAX.EPS

Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable


Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)

MAX4389/MAX4390/MAX4392MAX4396

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 19 2003 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.

TSSOP4.40mm.EPS

This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.

You might also like