Professional Documents
Culture Documents
30. Communicating information Content 30.1 Principles of modulation 30.2 Sidebands and bandwidth 30.3 Transmission of information by digital means 30.4 Different channels of communication 30.5 The mobile-phone network Learning outcomes Candidates should be able to: (a) understand the term modulation and be able to distinguish between amplitude modulation (AM) and frequency modulation (FM) (b) recall that a carrier wave, amplitude modulated by a single audio frequency, is equivalent to the carrier wave frequency together with two sideband frequencies (c) understand the term bandwidth (d) demonstrate an awareness of the relative advantages of AM and FM transmissions (e) recall the advantages of the transmission of data in digital form (f) understand that the digital transmission of speech or music involves analogue-todigital conversion (ADC) on transmission and digital-to-analogue conversion (DAC) on 1 reception
(g) show an understanding of the effect of the sampling rate and the number of bits in each sample on the reproduction of an input signal (h) appreciate that information may be carried by a number of different channels, including wire-pairs, coaxial cables, radio and microwave links and optic fibres (i) discuss the relative advantages and disadvantages of channels of communication in terms of available bandwidth, noise, crosslinking, security, signal attenuation, repeaters and regeneration, cost and convenience (j) describe the use of satellites in communication (k) recall the relative merits of both geostationary and polar orbiting satellites for communicating information (l) recall the frequencies and wavelengths used in different channels of communication (m) understand and use signal attenuation expressed in dB and dB per unit length
(o) understand that in a mobile-phone system, the public switched network (PSTN) is linked to base stations via a cellular exchange (p) understand the need for an area to be divided into a number of cells, each cell served by a base station (q) understand the role of the base station and the cellular exchange during the making of a call from a mobile phone set (r) recall a simplified block diagram of a mobile phone handset and understand the function of each block
Communication
Any system of communication must have transmitter and a receiver A simple system of communication at a short distance could be one person A speaking to another person B
A is the transmitter B is the receiver Communication system is sound waves
Disadvantages
Transmitting aerial Receiving aerial
Microphone
Amplifier
Speaker
Amplifier
Modulation
Modulation is a process whereby a high frequency wave, known as a carrier wave is transmitted. This carrier wave has either the amplitude varied or the frequency varied so as to carry information pg 427 Fig 16.2 A/AS level Physics Chris Mee In amplitude modulation(AM), the carrier wave has constant frequency. The amplitude of the carrier wave is made to vary in synchrony with the displacement of the information signal The rate at which the amplitude of the carrier wave varies is related directly to the frequency of the information signal Amplitude modulation is not the same as superposition. Superposition involves the addition of displacements, whereas AM is achieved by multiplication of the displacements In frequency modulation(FM), the amplitude of the carrier wave remains constant. The frequency of the carrier is made to vary in synchrony with the displacement of the information signal The use of a carrier wave allows different radio stations in the same area to transmit at the same time, but each radio station has a different transmitting carrier wave frequency. The receiver is tuned or adjusted to the frequency of whichever transmitter or radio station is desired i.e. the receiver accepts the signal transmitted on that particular carrier wave and rejects all other carrier wave frequencies7
Example
A sinusoidal carrier wave has a frequency of 800 kHz and an amplitude of 5.0 V. The frequency deviation of the carrier wave is 30 kHz V-1 i.e. for every 1.0 V change in displacement of the signal, the frequency of the carrier wave changes by 30 kHz. The carrier wave is frequency-modulated by a sinusoidal signal of frequency 10 kHz and amplitude 2.0 V. Describe the modulated carrier wave. Solution
Amplitude of information signal = 2.0 V. This gives a frequency variation of (2 x 30) = 60 kHz The carrier wave has a constant amplitude of 5.0 V The carrier frequency changes from 740 kHz to 860 kHz This change of frequency occurs 10000 times per second
Amplitude
(fC + fS ) fC (fC fS )
Frequency
The central frequency fC is the frequency of the carrier wave and it has the largest amplitude The other 2 frequencies, (fC + fS) and (fC fS) are known as the sideband frequencies or just sidebands The bandwidth is the range of frequencies occupied by the AM waveform. This bandwidth is equal to 2fS
9
10
11
12
cont..
Cost and simplicity
FM can be used to serve small local areas but it is simpler and cheaper to broadcast and receive using AM, as the AM transmitters are much simpler electronically than those for FM
The difference in the coverage is an advantage where local radio is concerned but a disadvantage as regards national radio
The bandwidth necessary for FM is greater
The quality of the received FM signal is much better because of the increased frequency spectrum and it also suffers less noise
14
Example
A particular transmitter is broadcasting an AM signal of frequency 200 kHz. The transmitter is broadcasting a programme of music with a maximum frequency of 4.5 kHz. Determine for this AM signal: (a) the wavelength (b) the bandwidth Solution
(a) wavelength = speed of em waves/frequency = 1500 m (b) bandwidth = 2 x 4.5 = 9.0 kHz
15
Digital transmission
16
Analogue signals
Any information that has the same variations with time as the information itself is known as an analogue signal. e.g. the signal produced by a microphone is analogous to the sound wave incident on the microphone Much of the information that we wish to transmit and communicate is analogue in nature e.g. speech, music, television pictures etc When any signal is transmitted over a long distance, it will pick up stray electromagnetic waves which we call noise Noise is not just unwanted sound, but any unwanted random signal that adds to the signal that is being transmitted Also the power of the transmitted signal and the received signal becomes less i.e. the signal is attenuated Hence for long distance transmission, the signal has to be amplified at regular intervals This amplification of an analogue signal also causes the noise to be amplified and so the signal becomes distorted or noisy pg 432 fig 16.6 Physics Chris Mee
17
Digital signals
A digital signal consists of a series of highs and lows with no values between the highs and lows The data in the signal is transmitted as a particular sequence of highs and lows or effectively a sequence of 1s and 0s This digital signal also suffers from noise and attenuation However on amplification, the noisy 1s and 0s can be re-shaped or regenerated to return the signal to the original form Such amplifiers are known as regenerator amplifiers whose function is to filter out any noise pg 432 fig 16.7 Physics Chris Mee Unlike an analogue signal, a digital signal can be transmitted over a long distance with regular regenerations without the signal becoming degraded Modern digital electronic circuits are in general more reliable and cheaper to produce than analogue circuits Additional advantage of digital systems is that extra information or data can be added to the transmissions. These extra data are a code for the receiving system so that the transmitted signal may be checked and corrected before the signal is finally produced
18
19
cont..
When reading a digital number, the bit on the left-hand side of the number is called the most significant digit or MSB. This bit has the largest value The bit on the right-hand side has the least significant value and is known as the least significant digit or LSB When the LSB is 1, this corresponds to decimal number 1 When the second bit shows 1, this corresponds to decimal number 2 When successive bits show 1 they correspond to decimal numbers 4,8,16,32,64,128,256,512,1024 etc Hence the binary number 1101 corresponds to 8+4+0+1 = 13 Conversely decimal number 11 equals 8+0+4+1 which corresponds to binary number 1011
20
Example
Convert 218710 to a binary number 2187 1093 1 546 1 273 0 136 1 68 0 34 0 17 0 81 40 20 10 01 218710 = 1000100010112
22
Example
Convert 1011001012 to a denary number Step 1: Write down the column values by starting with a 1 on the right-hand side then just keep doubling as necessary 28 27 26 25 24 23 22 2 1 20 256 128 64 32 16 8 4 2 1 Step 2: Enter the binary number under the column headings 256 128 64 32 16 8 4 2 1 1 0 1 1 00 101 Step 3: Add up all the column values where the binary digit is 1 256 + 64 + 32 + 4 + 1 = 357 So, 1011001012 = 35710 or just 357 since denary can be assumed in this case
24
Channels of communication
27
Transfer of information
A signal whether analogue or digital is transmitted and received using different channels of communication Also between conversions from analogue to digital signals or vice-versa, the signal has to be transferred from one place to another This may be achieved in various ways using different channels of communication including
Wire-pairs Coaxial cables Radio links Microwave links Optic fibres
28
Picture of wire-pair
29
Wire-pairs
It is the simplest link between a transmitter and receiver of information In the early days of electrical communication using Morse code, the transmitter and receiver were connected directly to one another by means of 2 copper wires(or 1 copper wire and earth return) known as a wire-pair In modern communication systems, wire-pairs are used mainly for shortdistance communication at relatively low frequencies e.g. linking telephones to the nearest exchange or linking a door bell in a house to the switch outside the door
30
Wire-pairs cont
High-frequency electrical signals lose their energy over short distances in wire-pairs i.e. the signals have high attenuation partly due to the heating caused by the electrical resistance of the wires and partly due to the emission of radiation(radio waves) since the wires acts as aerials Hence a signal going any distance in a wire-pair must be amplified at regular intervals Since the wire-pairs act as aerials, they also pick up any electromagnetic waves and unwanted signals as noise which causes deterioration of the signal Again, since wire-pairs are close to each other, they pick up each others signal This effect is known as cross-talk or cross-linking which means that wirepairs give rise to poor security since the signals can be tapped easily The bandwidth of a wire-pair is only 500 kHz and as a result wire-pairs are limited as to the amount of information that they can carry
31
Summary of wire-pairs
Are used mainly for short distance communications Cause high attenuation of signals Easily pick up noise Suffer from cross-talk Are of low security Have limited bandwidth
32
33
Coaxial cables
A coaxial cable consists of 2 wire conductors which are insulated
an inner metal conductor covered by an insulator a second conductor(in the form of thin wire braid) that covers the first insulator another protective layer of insulation covering the braided conductor
The braided 2nd conductor acts as the return for the signal and is earthed The earthed outer braiding shields the inner conductor from external interference Hence, coaxial cables are far less noisy than wire-pairs and provide better security Attenuation is also reduced, hence repeater amplifiers can be further apart on coaxial cables The bandwidth of coaxial cables is about 50 MHz, hence much more information can be carried along a coaxial cable than along a wire-pair However, coaxial cables are more costly Coaxial cables are used to connect an aerial to a television, astro aerial to the astro decoder
34
Radio waves
The alternating current in a wire acts as an aerial Energy is radiated from the aerial in the form of electromagnetic waves which travel outwards from the aerial with the speed of light Electromagnetic waves in the range of 30 kHz 3 GHz are generally referred to as radio waves The first radio waves used for communication were of very low frequency and hence very long wavelength. These radio waves were switched on and off so that communication was by Morse code Development of AM enabled voice communication Further developments including FM and the use of different carrier waves enabled higher quality communication and also more radio stations to operate in the same area
35
Sky wave
3 MHz 30 MHz
Surface wave
< 3 MHz
37
38
39
Microwaves
Microwaves are also electromagnetic waves and are in the range of 3 GHz to 30 GHz and are generally used for point to point communications as the range of transmissions is limited to line of sight Reflecting parabolic dishes are used so that the transmission is in the form of a parallel beam and so that as much wave power as possible can be focussed onto the receiving aerial The reflecting parabolic dishes at the transmitter or the receiver are not the aerials . The aerial is found at the focus of the transmitting or reflecting dish The bandwidth of a microwave link is of the order of 1 GHz which means that the microwave beam has a large capacity for transmitting information
40
41
Optic fibres
An optic fibre consists of a fine strand of very pure glass(thinner than hair) surrounded by a protective covering Pulses of light or infra-red radiation carrying digital data travel along the fibre as a result of total internal reflection The radiation pulses are provided by lasers and have very high frequencies of the order of 108 MHz(i.e.1014 Hz) In theory a single pulse need only last for 10-14 seconds; however lasers cannot be controlled at such high frequencies and the duration of a single pulse or bit is governed by the frequency at which the laser can be switched on and off With present technology the frequency is about 800 MHz, but technology is always improving Such high frequencies mean a large bandwidth so many different phone calls can share the same optic fibre
42
43
Signal attenuation
Loss of power when a signal passes along a wire or optic fibre is referred to as attenuation The amount of attenuation increases as the distance that the signal travels increases i.e. attenuation is proportional to distance Power is lost in various ways;
In the case of an electrical signal in a metal wire signal power is lost as heating in the wire In optic fibres light power is lost as a result of absorption in impurities in the glass and also scattering due to imperfections In a beam of electromagnetic waves travelling through air, power is lost as a result of absorption and scattering
In order that a signal is detected, the power of the signal must be a minimum number of times greater than the noise power. This ratio is known as the signal-to-noise ratio(S/N ratio). This ratio can be very large or very small Signals are amplified and the output of the amplifier is a certain number of times greater than the input. The amplifier gain could be 100,000 When a microwave signal is sent from Earth to a satellite, the signal power may be reduced by a factor of 1019 In order to condense the scale of such variations and to make the numbers 44 more manageable, the power levels are compared on a logarithmic scale
45
Example
A signal having a power of 2.4 W is amplified in a 2-stage amplifier. The first stage has again of 18 dB and the second stage provides a further amplification of 25 dB. Calculate: a) the total gain of the 2-stage amplifier b) the power of the output signal from the amplifier Solution a) For the 1st stage the input is V1 and the output is V giving a gain G1 = V/V1 For the 2nd stage the input is V and the output is V0 giving a gain G2 = V0/V Total gain = V0/V1 = (G2V)/(V/G1) = G1 x G2 = gain of 1st stage x gain of 2nd stage Gain, when expressed in dB is a logarithm, therefore when 2 gains are multiplied, then the gains in dB must be added together lg(total gain) = lg(gain of 1st stage x gain of 2nd stage) = lg(gain of 1st stage) + lg(gain of 2nd stage) = 18 + 25 = 43 dB b) Gain in dB = 10 lg(P2/P1) 43 = 10 lg(P2/(2.4 x 10-6)) and taking antilogs, P2= 0.048 W
46
Logarithm fundamentals
Base 10 The log of a number to the base 10 is the power to which the number 10 must be raised in order to give that number e.g. 100 = 102, so the logarithm to the base ten of 100 i.e. log 100, is 2.00 2.00 = 100.301 so the logarithm to the base ten of 2.00 i.e. log 2.00, is 0.301 101.699 = 50 and so log 50.0 = 1.699 Multiplication When 2 numbers are multiplied, if the numbers are expressed as numbers to the base 10, then the powers of the base ten are added e.g. 75 x 3.00 = 101.875 x 100.477 = 102.352, so 102.352 = 225 Division When 2 numbers are divided, if the numbers are expressed as numbers to the base 10, then the powers of the base ten are subtracted e.g. 75 3 = 101.875 100.477 = 101.398, so 101.398 = 25 Gain The gain of an amplifier is usually expressed in dB i.e. Gain in dB = 10 lg(Pout/Pin) in series, hence the combined gain is found either by multiplying together the 2 actual gains or by adding together the gains when expressed in dB 47
Signal attenuation
In a transmission line the amount of attenuation is dependent on the length of the line L Hence attenuation per unit length = (1/L) 10 lg(P2/P1) Attenuation per unit length is measured in dB km-1 Channel Attenuation per unit length(dB km-1)
Optic fibre 13 Coaxial cable 3 at 10 MHz Coaxial cable 40 at 3 GHz (hence attenuation for coaxial cables depends on frequency)
48
Example
The signal input to an optic fibre is 7.0 mW. The average noise power in the fibre is 5.5 x 10-19 W and the signal-to-noise ratio must not fall below 24 dB. The fibre has an attenuation of 1.8 dB km-1. Calculate: a) the minimum effective signal power on the cable b) the maximum uninterrupted length of the optic fibre through which the signal can be transmitted Solution a)
102.4 = Pmin/(5.5 x 10-19) therefore min effective signal power is = 1.38 x 10-16 W
b) total attenuation of signal to reach minimum = 10 lg(Pinput/Pmin) = 10 lg((7.0 x 10-3)/(1.38 x 10-16)) = 137 dB maximum uninterrupted length = total attenuation/attenuation per unit length = 137/1.8 49 = 76 km
Communication satellites
Although long distance communication using radio waves is possible on the MW waveband(as surface waves) and the SW waveband(as sky waves), for modern communication systems, there are 3 main disadvantages:
1) Long distance communication using sky waves is unreliable as it depends on reflection from layers of ions in the upper atmosphere which vary in height and density.
This gives rise to variable quality of signal. Surface waves are also unreliable because there is poor reception in hilly areas
2) The wavebands available on MW and SW are already crowded 3) The bandwidths that are available are narrow and completely unable to carry large amounts of information
Satellite communication enables more wavebands to be made available and at much higher frequencies, thus giving rise to a much greater data carrying capacity
50
The uplink and downlink carrier frequencies fup and fdown respectively are different so that the very low power signals received from Earth are not swamped by(i.e. can be distinguished from) the high power signal that is transmitted back to Earth Typical values of uplink/downlink are 6/4 GHz(6/4 GHz band), 14/11 GHz and 30/20 GHz The communication satellite may be in geostationary orbit which means that the satellite is above the equator, orbits the Earth with a period of 24 hours at a height of 3.6 x 104 km above the Earths surface and in the same direction as the rotation of the Earth which is from west to east From the viewpoint of a person on Earth, the satellite remains above the same point on the Earths surface
51
cont..
The transmitting aerial and the receiving aerial on Earth both have large parabolic reflectors For geostationary satellites, these aerials can be in fixed positions and hence the satellite does not need to be tracked This also means that a geostationary satellite can have a permanent link with a transmitting ground station hence maintaining communications with any point on the Earths surface that can receive the signal from the satellite A number of satellites with overlapping areas allows for long distance communications removing the need for long distance submarine cables International television broadcasting is possible allowing for live events in one country to be viewed by another
52
53
Polar satellites
Polar satellites are satellites that have low orbits and pass over the poles The orbital period is about 100 minutes Since the Earth rotates below these satellites, then in any period of 24 hours, the satellite will pass over every region of the Earths surface Continuous communications with a single polar satellite is not possible, however, information may be transmitted to the satellite while it is overhead This data can be stored and transmitted back to Earth when the satellite is above the appropriate area Continuous communications is possible using a number of polar satellites in orbits which are inclined to one another so that at least one satellite is always above the transmitter and receiver, but in this case the aerials must track the satellites in their orbits The advantage of using polar satellites is that their orbital height is only of the order of 105 m(a few hundred km) and hence delays in telephone conversations are not noticed Since polar satellites pass over the whole of the Earth in any 24 hour period, they are used for remote sensing e.g. military espionage, geological prospecting, weather forecasting etc The Global Positioning System(GPS or sat nav) uses the signals from a number of satellites that are not in geostationary orbits 54
55
Components:
Circuit board Antenna/aerial Liquid Crystal Display Keyboard Microphone Speaker Battery
56
Circuit Board
Analog-to-Digital, Digital-toAnalog converters Digital Signal Processor (DSP) Radio Frequency (RF) Control RF Amplifiers Power Control ROM and Flash memory Microprocessor
Front
Back
57
Microprocessor
58
LCD Display
Keypad
In modern systems, the telephone operator has been replaced by electronic relays that carry out the switching operations International exchanges called gateways have been introduced so that telephone communications may be worldwide The public switched telephone network(PSTN) uses the principle of exchanges. It is a "switched" network because a connection is made between caller and receiver before any communication begins Pg 448 fig 16.14 Physics by Chris Mee PSTN => local exchange trunk exchange gateway trunk exchange local exchange
60
PSTN cont..
The telephone network can be visualised as a "hub and spokes" arrangement. When the call is made, if it is local to the exchange, then the signal is carried along a spoke to the local exchange (i.e. the hub) then routed down another spoke to the receiver. If the call is a "trunk" call (i.e. not local to the exchange) then the local exchange routes the call to the trunk exchange for onward delivery to the exchange local to the receiver. For international calls, the local exchange will route to an international gateway Local exchange <> trunk exchange<>international gateway=PSTN In this PSTN system, The caller is connected to the PSTN through a local exchange Each caller has a fixed line, either a wire-pair or an optic fibre that links the subscriber(the phone user) to the local exchange The fixed line means that the user has limited mobility while making a call More recently, mobile phone systems were developed that did not require a permanent line to the local exchange Cellular system developed to provide mobile telephony: telephone access anytime, anywhere First mobile telephone system was developed and inaugurated in the U.S. in 1945 in St. Louis, MO. This was a simplified version of the system used today. 61
One and only one high power base station with which all users communicate.
Normal Telephone System
Wired connection
62
With only one high power base station, users phones also needed to be able to transmit at high powers (to reliably transmit signals to the distant base station).
Car phones were therefore much more feasible than handheld phones, e.g. police car phones.
63
Improved Design
Over the next few decades, researchers at AT&T Bell Labs, USA developed the core ideas for todays cellular systems.
Although these core ideas existed since the 60s, it was not until the 80s that electronic equipment became available to realize a cellular system.
In the mid 80s the first generation of cellular systems was developed and deployed.
64
65
cont..
When a mobile phone is linked to a base station, this is achieved using a particular carrier-wave frequency The range of carrier-wave frequencies is limited to a number that is far less than the number of mobile phones This means that each mobile phone does not have its own carrier frequency, and that the same frequency must be shared with many other phones at the same time This is made possible by having a network of base stations
66
67
68
multiple lower-power base stations of certain carrier frequency that service mobile users within their coverage area and handoff users to neighbouring base stations as users move. Together base stations tessellate the system coverage area.
69
3 Core Principles
Small cells 'tessellate' (a word in mathematics which means to cover a plane surface by repeated use of a single shape, without gaps or overlapping)
'Frequency reuse'
70
Tessellation
Some group of small regions tessellate a large region if they cover the large region without any gaps or overlaps. There are only three regular polygons that tessellate any given region. Three regular polygons that always tessellate:
71
Original cellular system was developed assuming base station antennas are omnidirectional, i.e. they transmit in all directions equally.
Users located outside some distance to the base station receive weak signals. Result: base station has circular coverage area.
72
Thus, ideally base stations have identical, circular coverage areas. What is the problem? Interference and blind spots
The most circular of the regular polygons that tessellate is the hexagon.
Thus, early researchers started using hexagons to represent the coverage area of a base station, i.e. a cell.
73
Base Station
Since the network resembles cells from a honeycomb, the name cellular was used to describe the resulting mobile telephone network.
74
Handoffs
Mobile phone users are by definition mobile, i.e. they move around while using the phone.
Thus, the network should be able to give them continuous access as they move.
This is not a problem when users move within the same cell.
When they move from one cell to another, a handoff is needed. A user is transmitting and receiving signals from a given base station, say B1. Assume the user moves from the coverage area of one base station into the coverage area of a second base station, B2. B1 notices that the signal from this user is degrading. B2 notices that the signal from this user is improving.
75
A Handoff (contd)
At some point, the users signal is weak enough at B1 and strong enough at B2 for a handoff to occur.
Specifically, messages are exchanged between the user B1 and B2 so that communication to/from the user is transferred from B1 to B2.
76
Frequency Reuse
Extensive frequency reuse allows for many users to be supported at the same time. Total em spectrum allocated to the service provider is broken up into smaller bands. A cell is assigned one of these bands. This means all communications (transmissions to and from users) in this cell occur over these frequencies only Neighbouring cells are assigned a different frequency band. This ensures that nearby transmissions do not interfere with each other. The same frequency band is reused in another cell that is far away. This large distance limits the interference caused by this cell In frequency reuse, a group of local cells use different frequencies to transmit/receive signals in their cell. This group of local cells is referred to as a cluster.
77
Clustersize of 7
Assume a clustersize of 7. This means that a total 395 voice channels are divided into groups of seven. Thus, each cell has about 56 voice channels. This is the most number of users that can be supported in a cell, i.e. roughly 10 square miles in normal environments. This may/may not be sufficient based on the distribution of users.
78
79
80
R.F. amplifier
Modulator / Oscillator
De-modulator / Oscillator
Parallel-to-serial converter
Serial-to-parallel converter
ADC
DAC
A.F. amplifier
A.F. amplifier
Microphone
Loudspeaker
81
82
Abrupt drop, or fading, of signal strength in the land mobile wireless channel is quite common. The fading feature of the mobile channel depends on the radio wave propagation environment.
83
The box houses the radio transmitters and receivers that let the tower communicate with phones. The radio transmitters connect with the antennae on the tower through thick cables.
84
85
Risks
Brain tumors?
The brain cancer patients did not report more cellular phone use
Side of the head on which the brain cancer occurred and the side on which the cellular phone was used no link.
86
87
88
For example, in cellular systems cell phones users in a local area typically communicate with the same cell tower.
How is the limited spectrum shared between these local transmitters? In such cases, system adopts a multiple access policy.
89
Frequency Division Multiple Access (FDMA) Time Division Multiple Access (TDMA) Code Division Multiple Access (CDMA)
90
FDMA
In FDMA, we assume that a base station can receive radio signals in a given band of spectrum, i.e., a range of continuous frequency values.
Each transmitter (user) transmits to the base station using radio waves in its own sub-band.
TDMA
In pure TDMA, base station does not split up its allotted frequency band into smaller frequency sub-bands.
Rather it communicates with the users one-at-a-time, i.e. round robin access
User N
Time
92
CDMA
CDMA is a more complicated scheme. Here all users communicate to the receiver at the same time and using the same set of frequencies. This means they may interfere with each other. The system is designed to control this interference. A desired users signal is deciphered using a unique code assigned to the user.
93
94
Channels
Channel is a general term which refers to a frequency in an FDMA system, a timeslot/frequency combination in TDMA, or a code in CDMA.
This way, a base station has a fixed number of channels and can support only that many simultaneous users.
95
96
97
These licenses allow the service provider to setup cellular towers in that region which can transmit over a prescribed band of frequencies.
98
Standards
The service providers must use one of the approved cellular standards for developing the cellular network in that region.
These standards are mutually agreed upon rules adopted by the industry on how the cell phone system operates.
These standards described the air interface, i.e., how cell phones and base stations must communicate with each other
These mutually agreed upon standards change over time, as technology progresses. The first cellular systems deployed in the U.S. adhered to a standard called Analog Mobile Phone System (AMPS). This system existed in the mid 80s to early 90s. The first cellular network used analog technology. Specifically, speech was converted to an FM signal and transmitted back and forth from user phones.
99
100
101
A group of local base stations are connected (by wires) to a mobile switching center (MSC). MSC is connected to the rest of the world (normal telephone system).
MSC
MSC
MSC MSC
102
They serve as intermediary between base stations that may be handing off users between each other.
103