You are on page 1of 8

MTN GSM NPI PROJECT

Wuse II, FCT, Abuja. 26th December, 2013

Introduction
Data Collection Date December 26th 2013

Test Route

Wuse II, FCT, Abuja

Test Procedure

MS 1 MS 2

Short Calls(3 Minutes) Long Calls(10 Minutes)

Test Essence

Optimization Check

BSC and Test Route

Summary: Analysis & Recommendation


S/N CELL NETWORK ISSUES/EVENTS REASON COMMENT/RECOMMENDATION Change the azimuth of 118B from 140o to Poor quality and There is the fair or reduced coverage and 120o and also increase the antenna height fair coverage poor quality along this road close to from 30m to 35m for better coverage and T118_MTN Switch due to the blockage of quality. the signal of 118B by a building Handover failures occurred from FC0101D to 1709A which is not a configured The swapped sectors or feeder cross on Handover failures, neighbour. There is crossed feeder on FC0101 should be corrected. Configure Poor Coverage FC0101 causing reduced or poor quality 1709A as neighbour to FC0101D, FC0101A, and Quality and coverage around T1709 (indoor site FC0101E,FC0101C,FC0101F bi at Valencia Hotel) which is also having a directionally. low signal strength at the area Handover failures occurred from 5848DA Handover failure, to 116C which is an overshooting cell that Poor Quality and is not configured as neighbour. There is Reduced/fair also reduced or fair coverage and poor Coverage quality at this area due to the overshooting cell 116C

118B

FC0101D

5848DA

Do mechanical down tilt of 116C by two degrees to improve HOSR, quality and coverage.

Summary: Analysis & Recommendation


4 1502DB Handover failure occurred from 1502DB Handover failure to FC0101E and FC0101C which are and Poor Quality missing neighbours, resulting poor quality and coverage. Configure FC101C, FC0101F,FC0101B,FC0101E as neighbours to 1502DB and 1502B to improve HOSR, coverage and quality.

1026DB

Configure 1443A and 1443B as neighbours Dropped call occurred here on 1026DB to 1026DB and 1026DB. Also confirm and due to its reduced coverage strength at change the azimuth of 1026B from 120o to Dropped Call and this area. Also, failure of 1026DB to 140o . Down tilt 1026B electrically by two Blocked Call handover to 1443A or 1443B, caused degrees to improve coverage and quality at blocked to occur as the coverage and the area quality reduced drastically

5848DB

Configure 1495C and 1495DC as neighbours to 5848B and 5848DB. Handover failure occurred from 5848DB Configure 1495DC as neighbour to 5848A. Handover failure, to 1495C due to missing neighbours. Configure 1495C and 1495DC as Poor Quality and 1495C has a very low signal at the area neighbour to 5848DA. Down tilt 1495C Fair Coverage causing reduced coverage and poor mechanically by two degrees to improve quality. quality and coverage

Analysis & Recommendation


Case 1

Comment: Handover failures


occurred from FC0101D to 1709A which is not a configured neighbour. There is crossed feeder on FC0101 causing reduced or poor quality and coverage around T1709 (indoor site at Valencia Hotel) which is also having a low signal strength at the area

Recommendation: The
swapped sectors or feeder cross on FC0101 should be corrected. Configure 1709A as neighbour to FC0101D, FC0101A, FC0101E,FC0101C,FC0101F bi directionally..

Problem: Handover failures, Poor Coverage and Quality


6

Conclusion
The network performance at Wuse II is averagely good and okay but the network quality needs to be optimized as there are areas at the city with reduced or poor quality due to interference and overshooting cells resulting into handover failures and blocked calls.
100 90 80 70 60 50 40 99.7 91.67 86.8

95.12
88.08

30
20 10 0 0 CSSR (%) CDR (%) Coverage Quality HOSR SQI

Thank You
WWW.Huawei.com
8

You might also like