You are on page 1of 25

7.

MOMENT DISTRIBUTION METHOD


7.1 MOMENT DISTRIBUTION METHOD - AN
OVERVIEW

• 7.1 MOMENT DISTRIBUTION METHOD - AN OVERVIEW


• 7.2 INTRODUCTION
• 7.3 STATEMENT OF BASIC PRINCIPLES
• 7.4 SOME BASIC DEFINITIONS
• 7.5 SOLUTION OF PROBLEMS
• 7.6 MOMENT DISTRIBUTION METHOD FOR STRUCTURES
HAVING NONPRISMATIC MEMBERS
7.2 MOMENT DISTRIBUTION METHOD -
INTRODUCTION AND BASIC PRINCIPLES
7.1 Introduction
(Method developed by Prof. Hardy Cross in 1932)
The method solves for the joint moments in continuous beams and
rigid frames by successive approximation.

7.2 Statement of Basic Principles


Consider the continuous beam ABCD, subjected to the given loads,
as shown in Figure below. Assume that only rotation of joints occur
at B, C and D, and that no support displacements occur at B, C and
D. Due to the applied loads in spans AB, BC and CD, rotations
occur at B, C and D.
150 kN
15 kN/m 10 kN/m
3m

A B C D
I I I
8m 6m 8m
In order to solve the problem in a successively approximating manner,
it can be visualized to be made up of a continued two-stage problems
viz., that of locking and releasing the joints in a continuous sequence.

7.2.1 Step I
The joints B, C and D are locked in position before any load is
applied on the beam ABCD; then given loads are applied on the
beam. Since the joints of beam ABCD are locked in position, beams
AB, BC and CD acts as individual and separate fixed beams,
subjected to the applied loads; these loads develop fixed end
moments.

-80 kN.m 15 kN/m -80 kN.m -112.5kN.m 10 kN/m


112.5 kN.m -53.33 kN.m 53.33 kN.m
3m
150 kN

A B C
8m B C D
6m 8m
In beam AB
Fixed end moment at A = -wl2/12 = - (15)(8)(8)/12 = - 80 kN.m
Fixed end moment at B = +wl2/12 = +(15)(8)(8)/12 = + 80 kN.m

In beam BC
Fixed end moment at B = - (Pab2)/l2 = - (150)(3)(3)2/62
= -112.5 kN.m
Fixed end moment at C = + (Pab2)/l2 = + (150)(3)(3)2/62
= + 112.5 kN.m

In beam AB
Fixed end moment at C = -wl2/12 = - (10)(8)(8)/12 = - 53.33 kN.m
Fixed end moment at D = +wl2/12 = +(10)(8)(8)/12 = + 53.33kN.m
7.2.2 Step II

Since the joints B, C and D were fixed artificially (to compute the the fixed-
end moments), now the joints B, C and D are released and allowed to rotate.
Due to the joint release, the joints rotate maintaining the continuous nature of
the beam. Due to the joint release, the fixed end moments on either side of
joints B, C and D act in the opposite direction now, and cause a net
unbalanced moment to occur at the joint.

150 kN
15 kN/m 10 kN/m
3m

A B C D
I I I
8m 6m 8m

Released moments -80.0 +112.5 -112.5 +53.33 -53.33


Net unbalanced moment -53.33
+32.5 -59.17
7.2.3 Step III

These unbalanced moments act at the joints and modify the joint moments at
B, C and D, according to their relative stiffnesses at the respective joints. The
joint moments are distributed to either side of the joint B, C or D, according
to their relative stiffnesses. These distributed moments also modify the
moments at the opposite side of the beam span, viz., at joint A in span AB, at
joints B and C in span BC and at joints C and D in span CD. This
modification is dependent on the carry-over factor (which is equal to 0.5 in
this case); when this carry over is made, the joints on opposite side are
assumed to be fixed.
7.2.4 Step IV
The carry-over moment becomes the unbalanced moment at the joints
to which they are carried over. Steps 3 and 4 are repeated till the carry-
over or distributed moment becomes small.
7.2.5 Step V
Sum up all the moments at each of the joint to obtain the joint
moments.
7.3 SOME BASIC DEFINITIONS
In order to understand the five steps mentioned in section 7.3, some words
need to be defined and relevant derivations made.

7.3.1 Stiffness and Carry-over Factors

Stiffness = Resistance offered by member to a unit displacement or rotation at a


point, for given support constraint conditions

MA MB A clockwise moment MA is
A B
applied at A to produce a +ve
A A bending in beam AB. Find A
and MB.
RA RB
L
E, I – Member properties
Using method of consistent deformations

MA
A fAA
B B
A L L
A

1
MAL2 f AA 
L3
A  
2EI 3EI

Applying the principle of


consistent
deformation, 3MA
 R f  0 R   
A A AA A 2L
MAL RAL2 MAL 4EI MA 4EI
A    MA  A; hence k  
EI 2EI 4EI L A L
Stiffness factor = k = 4EI/L
Considering moment MB,

MB + M A + R A L = 0
MB = MA/2= (1/2)MA
Carry - over Factor = 1/2

7.3.2 Distribution Factor


Distribution factor is the ratio according to which an externally applied
unbalanced moment M at a joint is apportioned to the various members
mating at the joint

+ ve moment M M
A B MBC C
A C
MBA
I2
I1 B MBD
L2
L1 I3
At joint B
L3
M - MBA-MBC-MBD = 0
D D
i.e., M = MBA + MBC + MBD

  4 E1 I 1   4 E 2 I 2   4 E 3 I 3 
           B
  L1   L 2   L 3 
  K BA  K BC  K BD  B
M M
 B  
 K BA  K BC  K BD  K
 K BA 
M BA  K BA B    M  ( D . F ) BA M
K 
 
Similarly
 K 
M BC   BC  M  ( D . F ) BC M
K 
 
 K BD 
M BD   M  ( D . F ) BD M
K 
 
7.3.3 Modified Stiffness Factor
The stiffness factor changes when the far end of the beam is simply-
supported.

MA A

A B

L
RA RB

As per earlier equations for deformation, given in Mechanics of Solids


text-books.
M AL
A 
3EI
M 3EI  3  4EI 
KAB  A     
A L  4  L 
3
 (KAB) fixed
4
7.4 SOLUTION OF PROBLEMS -

7.4.1 Solve the previously given problem by the moment


distribution method
7.4.1.1: Fixed end moments
wl 2 (15)(8) 2
M AB   M BA     80 kN .m
12 12
wl (150)(6)
M BC   M CB     112.5 kN .m
8 8
wl 2 (10)(8) 2
M CD   M DC     53.333 kN .m
12 12

7.4.1.2 Stiffness Factors (Unmodified Stiffness)


4 EI ( 4 )( EI )
K K    0 . 5 EI
AB BA L 8
4 EI ( 4 )( EI )
K  K    0 . 667 EI
BC CB L 6
 4 EI  4
K     EI  0 . 5 EI
CD
 8  8
4 EI
K   0 . 5 EI
DC 8
7.4.1.3 Distribution Factors

K BA 0.5EI
DFAB    0.0
K K 0.5   (wall stiffness)
BA wall
K 0.5EI
DFBA  BA
  0.4284
K BA  K BC 0.5EI  0.667EI
K BC 0.667EI
DFBC    0.5716
K BA  K BC 0.5EI  0.667EI
K 0.667EI
DF  CB
  0.5716
CB K CB  K CD 0.667EI  0.500EI
K CD 0.500EI
DFCD    0.4284
K K 0.667EI  0.500EI
CB CD
K
DFDC  DC  1.00
K
DC
7.4.1.4 Moment Distribution Table
Joint A B C D
Member AB BA BC CB CD DC
Distribution Factors 0 0.4284 0.5716 0.5716 0.4284 1
Computed end moments -80 80 -112.5 112.5 -53.33 53.33
Cycle 1
Distribution 13.923 18.577 -33.82 -25.35 -53.33
Carry-over moments 6.962 -16.91 9.289 -26.67 -12.35
Cycle 2
Distribution 7.244 9.662 9.935 7.446 12.35
Carry-over moments 3.622 4.968 4.831 6.175 3.723
Cycle 3
Distribution -2.128 -2.84 -6.129 -4.715 -3.723
Carry-over moments -1.064 -3.146 -1.42 -1.862 -2.358
Cycle 4
Distribution 1.348 1.798 1.876 1.406 2.358
Carry-over moments 0.674 0.938 0.9 1.179 0.703
Cycle 5
Distribution -0.402 -0.536 -1.187 -0.891 -0.703

Summed up -69.81 99.985 -99.99 96.613 -96.61 0


moments
7.4.1.5 Computation of Shear Forces

15 kN/m 10 kN/m
150 kN

B C
A D
I I I
8m 3m 3m 8m

Simply-supported 60 60 75 75 40 40
reaction
End reaction
due to left hand FEM 8.726 -8.726 16.665 -16.67 12.079 -12.08

End reaction
due to right hand FEM -12.5 12.498 -16.1 16.102 0 0

Summed-up 56.228 63.772 75.563 74.437 53.077 27.923


moments
7.4.1.5 Shear Force and Bending Moment Diagrams

52.077
75.563
2.792 m
56.23

27.923
3.74 m 74.437
63.77

S. F. D.
Mmax=+38.985 kN.m
Max=+ 35.59 kN.m
126.704 31.693
35.08

48.307
-69.806 3.74 m
84.92 98.297 2.792 m

-99.985 -96.613

B. M. D
Simply-supported bending moments at center of span

Mcenter in AB = (15)(8)2/8 = +120 kN.m

Mcenter in BC = (150)(6)/4 = +225 kN.m

Mcenter in AB = (10)(8)2/8 = +80 kN.m


7.5 MOMENT DISTRIBUTION METHOD FOR
NONPRISMATIC MEMBER (CHAPTER 12)

The section will discuss moment distribution method to analyze


beams and frames composed of nonprismatic members. First
the procedure to obtain the necessary carry-over factors,
stiffness factors and fixed-end moments will be outlined. Then
the use of values given in design tables will be illustrated.
Finally the analysis of statically indeterminate structures using
the moment distribution method will be outlined
7.5.1 Stiffness and Carry-over Factors

Use moment-area method to find the stiffness and carry-


over factors of the non-prismatic beam.

PA MA
MB
A

B

A
PA  ( K A ) AB  A M A   K  AB  A
M B  C AB M A
CAB= Carry-over factor of moment MA from A to B
A (= 1.0)
MA MB B (= 1.0)

B A
B

MA(KA) MA=CBAMB
MB=CABMA =CBAKB MB(KB)
=CABKA
(a) (b)

Use of Betti-Maxwell’s reciprocal theorem requires that the work


done by loads in case (a) acting through displacements in case (b) is
equal to work done by loads in case (b) acting through displacements in
case (a)

 M A  (0)   M B  (1)   M A  (1.0)   M B  (0.0)


C ABK A  C BA K B
7.5.2 Tabulated Design Tables

Graphs and tables have been made available to determine fixed-end


moments, stiffness factors and carry-over factors for common
structural shapes used in design. One such source is the Handbook of
Frame constants published by the Portland Cement Association,
Chicago, Illinois, U. S. A. A portion of these tables, is listed here as
Table 1 and 2

Nomenclature of the Tables


aA ab = ratio of length of haunch (at end A and B to the length
of span
b = ratio of the distance (from the concentrated load to end A)
to the length of span
hA, hB= depth of member at ends A and B, respectively
hC = depth of member at minimum section
Ic = moment of inertia of section at minimum section = (1/12)B(hc)3,
with B as width of beam
kAB, kBC = stiffness factor for rotation at end A and B, respectively

h h  h h 
L = Length of member

rA   , rB  
A moments

C at end A andBB, respectively;
C
MAB, MBA = Fixed-end specified in
tables for uniform load w or concentrated force P

 hC   hC 
h  h k EI r 
h h
k EI
B C
r 
Also K A  , KB 
A C B
A
h AB
C
C h BA CC

Also K 
k EILA , K  ABk EI
C LB
BA C

L L

You might also like